ADATA Technology Corp.

Transcription

1 60GB,120GB ADATA Technology Corp. 2.5 inch SATA SSD Datasheet S510 60GB 120GB V 1.1 Document Number: R

2 60GB,120GB Key Features: Capacity: 60GB, 120GB NAND Flash: Intel/Micron 25nm (MLC) Form Factor: 2.5 inch SATA Compatibility: Serial ATA 6Gb/s interface Complies with ATA-8/ACS-2 Standard S.M.A.R.T feature supported NCQ Command set supported Trim Command supported AES 128/256 supported Performance Sequential Read: Up to 550MB/s Power Consumption: Active: 0.9W Idle: 0.5W Temperature: Opration: 0 C ~ 70 C Non-operation: -40 C ~ 85 C Shock 1500G/0.5ms Vibration 20G Peak, 10~2000Hz Reliability MTBF: 1,200,000 hours Uncorrectable Bit Error Rate(UBER): Sequential Write: Up to 510MB/s Random 4K Read: Up to 20K Random 4K Write: Up to 85K

3 60GB,120GB Revision History Revision No. History Draft Date Remark Editor 0.9 Aug. 30, 2011 Preliminary Robin Chung 1.0 Oct. 5, 2011 Add 60GB Robin Chung

4 Table of Contents 1.0 General Description Mechanical Specification Physical dimensions and Weight Product Dimensions Product Specification Interface and configuration Capacity Performance Read/Write & IOPS Performance PCMark Vantage Scores...9 [Table 3-5] PCMark Vantage Performance Electrical Operating Voltage Power Consumption (Typical) Environmental Conditions Reliability Supported Command Sets ATA Feature Command Sets Identify Device ConfigDriveUnique Command Block Pin assignment and descriptions SATA Interface Product Line up...17 [Table 7-1] Product Line up Package Specifications...17

5 1.0 General Description Taking the advantages of NAND flash memory, Solid State Drive (SSD) provides better solutions on durability, performance, and power efficiency over traditional hard disk drives. Employing static wear-leveling technology to maximize device mean time between failures (MTBF), The SSD solutions are your best choice on wide-ranged mobile computing devices and consumer electronic products. With standard SATA form factor or customized module form factor, The 2.5 ADATA SSD S510 use latest technology to enhance Read/Write performance up to 550/510(MB/s) and offers capacities 60GB and 120GB, using MLC NAND type flash memories. [Figure 1-1] Functional Block Diagram

6 2.0 Mechanical Specification 2.1 Physical dimensions and Weight [Table 2-1] Dimensions and Weight Model Length(mm) Width(mm) Height(mm Weight(gram) 60GB Max Max 70.1 Max ±1g 120GB Max Max 70.1 Max ±1g 2.2 Product Dimensions

7 [Figure 2-1] Physical Dimensions ADATA S510

8 3.0 Product Specification 3.1 Interface and configuration Burst read/write rate is 600 MB/sec (6.0 Gb/sec). Compliant with Serial ATA International Organization: Serial ATA Revision 2.6. Compliant SSD Alliance compliance program 3.2 Capacity Model [Table 3-1] User Addressable Sectors S510 Unformatted Capacity 60GB 120GB Total User Addressable Sectors (LBA Mode) 117,038, ,245,680 Total useable capacity may be less (duo to formatting, flash management, and other functions). 1GB=1,000,000,000 bytes; 1sector = 512bytes. 3.3 Performance Read/Write & IOPS Performance [Table 3-2] Read/Write & IOPS Performance 60GB 120GB Unit Max 128K Sequential Read Max 128K Sequential Write MB/s MB/s Max 4K Random Read 18K 20K IOPS 4K Random Write 80K 85K IOPS Seq. Read & Write speed test by IOmeter 2010 with 00 pattern (Queue depth of 32; Measurements are performed on 10% capacity of LBA range. Write cache enable) IOPS Test Utility: IOmeter 2010 (Queue depth of 32; Measurements are performed on 10% capacity of LBA range. Write cache enable) The system conditions and test environment may affect test result

9 [Table 3-3] Read/Write Performance (AS-SSD) ADATA S510 60GB 120GB Unit Sequential Read MB/s Sequential Write MB/s 4K-64 Thrd Read MB/s 4K-64 Thrd Write MB/s Seq. Read & Write speed test by AS-SSD with Random pattern [Table 3-4] Read/Write Performance (ATTO) 60GB 120GB Unit Sequential Read MB/s Sequential Write MB/s Seq. Read & Write speed test by ATTO The system conditions and test environment may affect test result PCMark Vantage Scores [Table 3-5] PCMark Vantage Performance 60GB 120GB PCMark Electrical Operating Voltage [Table 3-6] Operating Voltage Operating Voltage Input Power DC 5.5V ± 10% Maximum Ripple 100mV p-p or less

10 3.4.2 Power Consumption (Typical) [Table 3-7] Power Consumption (Typical) ADATA S510 Power 60GB 120GB Unit Active Mode W Idle Mode W Active average power measured while during execution of MobileMark 2007 with DIPM enable Idle mode power measure during running Win7 without any access to the SSD. The power consumptions depend on the disk capacity and the type of NAND flash components being used 3.5 Environmental Conditions [Table 3-8] Temperature, Humidity, Shock, Vibration Feature Operator Non-Operator Temperature 0 C to 70 C -40 C to 85 C Humidity Vibration Shock 0 to 55 / 5%~95% RH, non-condensing 20G Peak, 10~2000Hz 1500G, duration 0.5ms, Half Sine Wave 3.6 Reliability Parameter [Table 3-9] Reliability Specification Value Uncorrectable Bit Error Rate (UBER) 1 sector in bits read, Max Mean Time Between Failures (MTBF) The MTBF statistics were calculated by Part Count Method, not relevant to individual units 1,000,000 hours

11 4.0 Supported Command Sets 4.1 ATA Feature Command Sets ADATA S511 supports all the mandatory ATA commands defined in ATA/ATAPI-7 specification. The supported command sets are listed as below. Feature Set [Table 4-1] Supported ATA Feature Sets 48-bit Address Feature Set Advanced Power Management(APM) Feature Set Device Configuration Overlay(DCO) Extended Power Conditions (EPC) General Feature Set General Purpose Logging(GPL) Feature Set Host Protected Area(HPA) Feature Set Long Logical Sector (LLS) Feature Set non-512 Native Command Queuing(NCQ) Feature Set Power Management Feature Set Power-Up In Standby (PUIS) Feature Set Sanitize Device Feature Set Security Feature Set S.M.A.R.T Feature Set Software Setting Preservation (SSP) Feature Set Trusted Computing Feature Set Write-Read-Verify Feature Set

12 Command OPCode Command OPCode CHECK POWER MODE E5h SECURITY DISABLE PASSWORD F6h DATA SET MANAGEMENT 06h SECURITY ERASE PREPARE F3h DEVICE CONFIGURATION OVERLAY B1h SECURITY ERASE UNIT F4h DOWNLOAD MICROCODE 92h SECURITY FREEXE LOCK F5h DOWNLOAD MICROCODE DMA 93h SECURITY SET PASSWORD F1h EXECUTE DEVICE DIAGNOSTIC 90h SECURITY UNLOCK F2h FLUSH CACHE E7h SEEK 70h FLUSH CACHE EXT EAh SET FEATURES EFh IDENTIFY DEVICE ECh SET MAX ADDRESS F9h IDENTIFY PACKET DEVICE A1h SET MAX ADDRESS EXT 37h IDLE E3h SET MULTIPLE MODE C6h IDLE IMMEDIATE E1h SLEEP E6h INITIALIZE DEVICE PARAMETERS 91h SMART B0h NOP 00h STANDBY E2h READ BUFFER E4h STANDBY IMMEDIATE E0h READ BUFFER DMA E9h STANDBY NON-DATE 5Bh READ DMA EXT 25h TRUSTED RECEIVE 5Ch READ DMA WITHOUT RETRIES C9h TRUSTED RECEIVE DMA 5Dh READ FPDMA QUEUED 60h TRUSTED SEND 5Eh READ LOG DMA EXT 47h TRUSTED SEND DMA 5Fh READ LOG EXT 2Fh WRITE BUFFER E8h READ LONG 22h WRITE BUFFER DMA EBh READ LONG (without Retry) 23h WRITE DMA EXT 35h READ LONG WITHOUT RETRY 23h WRITE DMA WITHOUT RETRIES CBh READ MULTIPLE C4h WRITE FPDMA QUEUED 61h READ MULTIPLE EXT 29h WRITE LOG DMA EXT 57h READ NATIVE MAX ADDRESS F8h WRITE LOG EXT 3Fh READ NATIVE MAX ADDRESS EXT 27h WRITE LONG 32h READ SECTORS(S) EXT 24h WRITE LONG (without Retry) 33h READ SECTORS WITHOUT RETRY 21h WRITE LONG WOTHOUT RETRY 33h READ VERIFY SECTOR(S) 40h WRITE MULTIPLE C5h READ VERIFY SECTIR(S) (without Retry) 41h WRITE MULTIPLE EXT 39h READ VERIFY SECTIR(S) EXT 42h WRITE SECTIR(S) EXT 34h RECALIBRATE 10h WRITE SECTOR WITHOUT RETRY 31h REQUEST SENSE DATA EXT 0Bh WRITE UNCORRECTABLE EXT 45h

13 4.2 Identify Device ADATA S511 responds to ATA IDENTIFY DEVICE command with a pre-defined string of information on features, hardware and firmware revision information, and functionality support indicators. Many portions of the IDENTIFY DEVICE response string are configurable at manufacturing time via the ConfigDriveUnique SCT diagnostic command ConfigDriveUnique Command Block ConfigDriveUnique command is used to configure firmware settings. It contains both read and write data and each of them is described in the following sections. [Table 4-2] ConfigDriveUnique Command Block Bytes Field Description 0-1 Action Code Command = C008h 2-3 Function Code Data to return -0000h: Read ConfigDriveUnique settings h: Write ConfigDriveUnique settings Reserved Reserved ConfigureDriveUnique Write Data [Table 4-3] ConfigureDriveUnique Write Data Bytes Field Description Identify Mask Mask of the bits to be configured in IDENTIFY DEVICE information. A value of one in the mask allows the corresponding bit to be configured Identify Data New data for IDENTIFY DEVICE. Bits falling outside of the mask are ignored UART Frequency Reserved (Set to 0) Flags Options for serial output and SATA status coalescing LED and GPIO Setting Specify GPIO behavior and LED configuration options Assigned ID The Controller Vendor ID assigned to the manufacturer Customer ID The ID assigned by the manufacturer Configuration ID Configuration ID of the firmware being loaded on the device

14 Diagnostic Unlock Key Reserved Reserved PFAIL Hold-up Test Hours PFAIL Hold-up Test Discharge Timeout PFAIL Hold-up Test Enable Reserved Reserved Power Mode Configuration Temperature Sensor 1 Configuration Temperature Sensor 2 Configuration Reserved Reserved Security Erase Behavior Enhanced Security Erase Behavior SATA Command Behavior Reserved Reserved Max LBA Entry Count Max LBA Entries ADATA S510 Set a new diagnostic unlock key. MFB will store the key correctly but will use the default until flashware is loaded. Number of hours between auto-initiated PFAIL hold-up tests. The value is dithered to prevent arrays of disks entering the PFAIL hold-up test at the same time. Maximum number of milliseconds to allow the PFAIL hold-up supply to discharge during a PFAIL hold-up test. Enables or disables the PFAIL hold-up test. Specify the configuration of power mode. Specify the configuration of temperature sensor 1. Specify the configuration of temperature sensor 2. Configures the behavior of SECURITY ERASE UNIT command. Determines whether the enhanced security erase protocol can be configured through the Change Enhanced Security Erase Behavior command (C605h). Behavior of SATA command. Number of max LBA entries. Equal to the number of sector sizes supported (Valid values are 1h~Ah). Max LBA setting for each supported sector size. Each entry is 8 bytes long SMART Configuration Configuration of SMART command.

15 4.2.3 ConfigureDriveUnique Read Data [Table 4-4] ConfigureDriveUnique Read Data Bytes Field Description ADATA S Firmware Identify Mask Identify Mask Identify Data ConfigDriveUnique Data Mask of the bits that firmware allows to be modified for IDENTIFY DEVICE. This mask is OP'ed with the identify mask Mask of the bits to be configured in IDENTIFY DEVICE information. A value of one in the mask allows the corresponding bit to be configured. New data for IDENTIFY DEVICE. Bits falling outside of the mask will be ignored Follows the same format as write ConfigDriveUnique(offset by 512 bytes)

16 5.0 Pin assignment and descriptions 5.1 SATA Interface SATA Interface signals Power [Figure 4-1] SATA Interface No. Pin Name. Descriptions S1 GND System Ground S2 Rx+ S3 Rx- Differential signals pair Receive S4 GND System Ground S5 Tx- S6 Tx+ Differential signals pair Transmit S7 GND System Ground P1 V V Power supply P2 V V Power supply P3 V33/PC +3.3V Power supply, 2 nd Pre-charge P4 GND System Ground P5 GND System Ground P6 GND System Ground P7 V5/PC +5V Power supply, 2 nd Pre-charge P8 V5 +5V Power supply P9 V5 +5V Power supply P10 GND System Ground P11 DAS Reserved P12 GND System Ground P13 V12/PC +12V Power supply, 2 nd Pre-Charge P14 V12 +12V Power supply P15 V12 +12V Power supply

17 6.0 Product Line up [Table 7-1] Product Line up Part Number Capacity Type Remark AS510S3-60GM-C 60GB 2.5 SATA AS510S3-120GM-C 120GB 2.5 SATA 7.0 Package Specifications [Figure 8-1] Package