SPECIFICATION MANUAL. Panic & Emergency Exit Hardware. Part of the Securefast Group SECUREFAST DEEDLOCK PINSON TATE COLSON. securefast.co.uk.

Transcription

1 CI/SfB (31.59) X Panic & Emergency Exit Hardware securefast.co.uk SPECIFICATION MANUAL SECUREFAST Part of the Securefast Group DEEDLOCK PINSON TATE COLSON

2 1 Panic & Emergency Exit Hardware Panic & Emergency Exit Hardware 2 Which to choose? Securefast offers a range of panic and emergency exit hardware which is operated either by Touch Bar, Push Bar or Push Pad. All our panic and emergency exit hardware is comprehensively tested for compliance with the latest European Standards and is CE marked. Touch Bar Range Our standard projection Touch Bar range of panic exit hardware provides a sleek and clean looking option for those applications where a high quality architectural look is a priority and where multi point latching may be required. Complies with EN1125:2008 and is therefore suitable for applications which will be used by the general public such as in a cinema, hospital or shopping centre. Push Bar Panic Exit Hardware For Panic applications our versatile Push Bar range of panic exit hardware in latch, vertical bolts or mortice nightlatch operator will satisfy single and double door applications. Complies with EN1125:2008 and is therefore suitable for applications which will be used by the general public such as in a cinema, hospital or shopping centre. Push Pad Emergency Exit Hardware For Emergency situations, our Push Pad range of exit hardware is available in latch, vertical bolt and mortice nightlatch versions for single and double doors. Complies with EN179:2008 and is therefore suitable for applications where occupants are familiar with the exit such as an office, factory or warehouse.

3 3 Touch Bar Panic Exit Hardware - EN1125:2008 Touch Bar Panic Exit Hardware - EN1125: SED600 Series SED601 Top Pullman latch SED602 Touch Bar Series Touch Bar Panic Latch - Single Point Latching Touch Bar Panic Bolt - Two Point Latching The Securefast Touch Bar Series of panic exit hardware provides a high quality option which combines sleek architectural styling with superb performance characteristics. The main feature of the design is the tactile aluminium touch bar which is not only visually attractive but is comfortable to grip, enabling the unit to be used to close the door and is easy to cut on-site during installation. The Series is available in single, double or triple latching point variations for single or double door combinations and can be used with or without external access device. The Securefast Touch Bar Series is not just attractive in appearance but has undertaken 2 million test cycles (10 times the highest requirement of the standard) offering exceptional levels of durability and functionality. Tested by independent test house to EN 1125:2008 Panic Exit Hardware, and CE marked for safety. Touch bar activated single point panic latch with the following features: Non handed, suitable without alteration for left or right hand applications Can be cut down on site suitable for doors up to 1240mm wide Additional length bar can be supplied for doors up to 1540mm wide Narrow stile suitable for upvc doors and glass panelled doors Single latch with anti-thrust protection Universal keep suitable for timber or aluminium single doors or double door combinations (for steel and upvc doors see Keep Options on page 17) Suitable for single doors or the active leaf of a rebated double door Optional hold-back available enabling the door to be put into free access (order additional SED600/HB) Optional Microswitch concealed in tail end of the unit to integrate with an access control system (order additional SED600/MS) 240 hour salt spray corrosion resistance on all finishes Bottom Pullman latch Touch bar activated two point panic bolt with the following features: Fire rated to EN Can be cut down on site suitable for doors up to 1240mm wide and up to 2450mm high Vertical shoot bolts with aluminium covers can be cut down on-site Top and bottom Pullman latches are adjustable for perfect alignment and smooth activation and built in anti-thrust protection Non handed, suitable for left or right hand applications Suitable for single doors or the active leaf of a rebated double door Supplied with easy clean keep for bottom Pullman and surface keep for top Pullman to suit timber and aluminium doors (for steel and upvc doors see Keep Options on page 17) Additional length bar can be supplied for doors up to 1540mm wide Optional hold-back available enabling the door to be put into free access (order additional SED600/HB) Optional Microswitch concealed in tail end of the unit to integrate with an access control system (order additional SED600/MS) SC Satin Chrome (stainless steel appearance) available to order 240 hour salt spray corrosion resistance on all finishes SC Satin Chrome (stainless steel appearance) available to order Single Point panic latch Two Point panic latch SED601/M/SE Single point latching - silver EN AA SED602/VM/SE Two point latching - silver EN1125 With OAD Without OAD SED601/M/SC Single point latching - satin chrome AA SED602/VM/SC Two point latching - satin chrome 36mm 47mm 73mm 110mm 16mm 17.5mm 73mm 110mm 112mm

4 5 Touch Bar Panic Exit Hardware - EN1125:2008 Touch Bar Panic Exit Hardware - Accessories 6 SED603 SED600/LE & SED600/LEC SED600/LEC SED600/KNC Touch Bar Panic Latch - Three Point Latching Outside Access Device with Lever Upper side Pullman latch (shown on double door application) Touch bar activated three point panic latch with the following features: Fire rated to EN Can be cut down on site suitable for doors up to 1240mm wide and up to 2450mm high Vertical shoot bolts with aluminium covers can be cut down on-site Side Pullman latches top and bottom with adjustable keep for perfect alignment Non handed, suitable for left or right hand applications Suitable for single doors or the active leaf of a rebated double door Universal keep for timber & aluminium frames Lever operated external access unit with euro profile cylinder locking Designed to fully comply with EN1125 for Panic Exit applications Suitable for use with all single and multiple point Touch Bar panic exit hardware Bolt through into the outside unit from the internal mounting plate of the panic device Key retention feature ensures OAD is always secure Available with or without cylinder (40mm single cylinder) Available in silver finish. Other finishes available to special order SED600/KN & SED600/KNC SED600/ES Lower side Pullman latch (shown on double door application) For steel and upvc doors please see optional keeps on page 17 Additional length bar can be supplied for doors up to 1540mm wide Optional hold-back available enabling the door to be put into free access (order additional SED600/HB) Optional Microswitch concealed in the tail end of the unit to integrate with an access control system (order additional SED600/HB) 240 hour salt spray corrosion resistance on all finishes SC Satin Chrome (stainless steel appearance) available to order Outside Access Device with Fixed Knob Designed to fully comply with EN1125 for Panic Exit applications Fixed knob For use with Touch Bar single latch only Bolt through into the outside unit from the internal mounting plate of the panic latch Available with or without cylinder (40mm single cylinder) Available in silver finish. Other finishes available to special order Electric Release Designed for use with Securefast Touch Bar panic exit hardware, the electric release enables mechanical Panic exit hardware to be used with an electronic access control system to provide access from outside. In normal use the panic exit device will provide escape from inside with a digital code, card or proximity device giving access from outside. Release operates with a 12v DC supply. Three Point panic latch SED603/HM/SE SED603/HM/SC Three point latching - silver Three point latching - satin chrome EN1125 With OAD Without OAD Double Door Configurations (Rebated or Non-Rebated) Rebated Doors Non-Rebated Doors Rebated Doors SED602 SED601 SED602 SED602 SED602 SED603 36mm 53mm 16mm 17.5mm 73mm 110mm 129mm

5 7 Touch Bar Panic Exit Hardware - Electronic Actuator Push Bar Panic Exit Hardware - EN1125: AEB800 SED991 Microswitch Touchbar Electronic actuator for use in Panic applications. The actuator provides touch bar operation across the door width which activates an electronic locking device. Designed to fully comply with pren13637 for electrical panic & emergency exit systems Can be cut down on site suitable for doors up to 1240mm wide Minimum unit width 365mm Ideally used in conjunction with face to face electromagnets (please contact us for further information on these and other suitable locking devices) Suitable for single doors, rebated or non-rebated double doors Dual switching for lock activation and monitoring Operates 12v or 24v DC Max. 5 Amp Universal keep - surface mounted Universal keep morticed into frame Optional Hold-Back function housed beneath arm of mechanism unit Push Bar Panic Latch Push bar single point panic latch with the following features: Supplied as Left Hand or Right Hand but can be reversed on-site Tested for use on Fire Doors to EN Optional hold-back facility (see page 20 for conditions of use) Can be cut down on site suitable for doors up to 1300mm wide Universal Keep for single doors and rebated double door applications. Keep can be surface mounted or morticed into a timber frame on single door applications Supplied with fixings for timber doors Can be fixed with self tapping screws Optional Microswitch can be concealed in the slave unit to integrate with an access control system 240 hour salt spray tested Range of accessories (see pages 17/18) SAA Satin anodised aluminium Powder coated colours in Blue, Green and Red available to order. SC Satin Chrome plated Microswitch Touchbar Single panic latch 1000mm max. AEB800/SE Electronic touch bar actuator - Silver SED991/SE Panic latch - silver EN1125 With OAD Without OAD AEB800/BE Electronic touch bar actuator - Blue SED991/SC Panic latch - satin chrome Electromagnetic Lock (see P.18) AEB800/GN AEB800/RD Electronic touch bar actuator - Green Electronic touch bar actuator - Red SED991/SE/HB SED991/SC/HB Panic latch with hold back - silver Panic latch with hold-back - satin chrome Break Glass Control Unit Power Transfer (see P.17) 910mm 70mm 180mm 97mm

6 9 Push Bar Panic Exit Hardware - EN1125:2008 Push Bar Panic Exit Hardware - EN1125: Top shoot with standard top trip release SED992 SED995 Push Bar Panic Bolt Push bar activated double vertical bolt with the following features: Patent Application No. GB Push Bar Panic Actuator Push bar mortice nightlatch panic actuator with the following features: Universal for left and right hand applications Tested for use on Fire Doors to EN Optional hold-back facility available Can be cut down on site suitable for doors up to 1300mm wide and 2500mm high Adjustable top/bottom shoots with ±5mm of adjustment Anti thrust device prevents shoot bolt being forcibly retracted Supplied with easy clean socket and flat plate keep Optional Microswitch can be concealed in the slave unit to integrate with an access control system 240 hour salt spray tested Range of accessories (see pages 17/18) Supplied with fixings for timber doors Universal for left or right hand applications Tested for use on Fire Doors to EN Lockcase meets the requirements of EN Can be cut down on site for doors up to 1300mm wide Range of accessories (see page 17) Single cylinder required for outside access (SEU412) SE Powder coated silver (as standard) SC Satin Chrome plated Bottom shoot with flat plate Bottom shoot with standard easy clean socket SC Satin Chrome plated Nightlatch lockcase has the following features: - Reversible latchbolt - 72mm centres, 60mm backset - Single piece stainless steel square ended forend. For round ended forend suffix product code RF - With or without anti-thrust Optional Microswitch can be concealed in the slave unit to integrate with an access control system Supplied with fixings for timber doors When used on a rebated double door combination, a 13mm rebate kit, SEU706 must be specified. Vertical panic bolts Single panic mortice nightlatch SED992/SE Panic bolt - silver EN1125 With OAD Without OAD SED995/SE/72 Panic actuator & nightlatch - silver EN1125 With Cylinder Without Cylinder SED992/SC Panic bolt - satin chrome SED995/SC/72 Panic actuator & nightlatch - satin chrome SED992/SE/HB Panic bolt with hold back - silver SED995/SE/72/AT Panic actuator & anti-thrust nightlatch - silver SED992/SC/HB Panic bolt with hold back - satin chrome SED995/SC/72/AT Panic actuator & anti-thrust nightlatch - satin chrome For round ended forend suffix product code RF 90mm 24mm 180mm 72mm 180mm 235mm 97mm 97mm 60mm

7 11 Push Bar Panic Exit Hardware - EN1125:2008 Push Pad Emergency Exit Hardware - EN179: Double Door Configurations Double door configurations can be achieved using combinations of: Securefast SED991 Securefast SED992 Securefast SED995 The universal strike plate supplied with the SED991 is suitable for use on single doors or rebated double door applications, eliminating the need to specify a dedicated double door set or a replacement strike component. The diagrams below show one hand of combination only. The same components can be used to create the opposite hand on site. Non-Rebated Door Applications SED992 SED992 Please note, when used on rebated doors a door co-ordinator will be required on self closing doors to ensure the doors close in the correct sequence. A rebate kit will also be required for use with mortice nightlatches on rebated doors using the SED995 actuator. SED992 SED995 SED993 Push Pad Emergency Latch Push Pad single point emergency latch with the following features: Supplied as Left Hand or Right Hand but can be reversed on-site Tested for use on Fire Doors to EN Optional hold-back facility (see page 20 for conditions of use) Universal Keep for single doors and rebated double door applications. Keep can be surface mounted or morticed into a timber frame on single door applications 240 hours salt spray tested Range of accessories (see page 17/18) Universal keep - surface mounted Optional Hold-Back function housed below arm of mechanism unit Non rebated double door using vertical bolts SC Satin Chrome plated Single emergency latch Rebated Door Applications SED992 SED991 SED992 SED995 SED993/SE Emergency latch - silver EN179 With OAD Without OAD SED993/SC SED993/SE/HB Emergency latch - satin chrome Emergency latch with hold-back - silver SED993/SC/HB Emergency latch with hold-back - satin chrome 180mm Active Leaf Active Leaf Universal strike showing use on rebated double door application. 98mm

8 13 Push Pad Emergency Exit Hardware - EN179:2008 Push Pad Emergency Exit Hardware - EN179: SED994 Push Pad Emergency Bolt Patent Application No. GB SED996 Push Pad Emergency Actuator Push pad vertical emergency bolt with the following features: Push pad mortice nightlatch emergency actuator with the following features: Universal for left and right hand applications Tested for use on Fire Doors to EN Optional hold-back facility available (see conditions on page 20) Can be cut down on site suitable for doors up to 2500mm high Adjustable top/bottom shoots with ± 5mm of adjustment Anti thrust device to prevent shoot bolt being forcibly retracted Supplied with easy clean socket and flat plate keep 240 hour salt spray tested Range of accessories (see page 17/18) Supplied with fixings for timber doors Top shoot with standard top trip release Bottom shoot with standard easy clean socket Universal for left or right hand applications Tested for use on Fire Doors to EN Lockcase meets the requirements of EN Range of accessories (see page 17) Nightlatch lockcase has the following features: - Reversible latchbolt - 72mm centres, 60mm backset - Single piece stainless steel square ended forend. For round ended forend suffix product code RF - With or without anti-thrust Single cylinder required for outside access Supplied with fixings for timber doors SC Satin Chrome plated SC Satin Chrome plated When used on a rebated double door combination, a 13mm rebate kit, SEU706 must be specified. Vertical emergency bolts Bottom shoot with flat plate Single emergency mortice nightlatch SED994/SE Emergency bolt - silver EN179 With OAD Without OAD SED996/SE/72 Emergency actuator & nightlatch - silver EN179 With Cylinder Without Cylinder SED994/SC Emergency bolt - satin chrome SED996/SC/72 Emergency actuator & nightlatch - satin chrome SED994/SE/HB Emergency bolt with hold-back - silver SED996/SE/72/AT Emergency actuator & anti-thrust nightlatch - silver SED994/SC/HB Emergency bolt with hold-back - satin chrome SED996/SC/72/AT Emergency actuator & anti-thrust nightlatch -satin chrome For round ended forend suffix product code RF 90mm 24mm 180mm 72mm 180mm 235mm 97mm 60mm 98mm

9 15 Push Pad Emergency Exit Hardware - EN179:2008 Outside Access for Panic & Emergency Exit Hardware 16 Double Door Configurations SED900 & SED990 Double door configurations can be achieved using combinations of: Securefast SED993 Securefast SED994 Securefast SED996 The universal strike plate supplied with the SED993 is suitable for use on single and also on rebated double door applications, eliminating the need to specify a dedicated double door set or a replacement strike component. The diagrams below show one hand of combination only. The same components can be used to create the opposite hand on site. Non-Rebated Door Applications SED994 SED994 Please note, when used on rebated doors a door co-ordinator will be required on self closing doors to ensure the doors close in the correct sequence. A rebate kit will also be required for use with mortice nightlatches on rebated doors using the SED996 actuator. SED994 SED996 Outside Access Devices Providing external access to doors fitted with Panic and Emergency Exit hardware: Suitable for use with SED991, SED992, SED993 and SED994 push bar and push pad exit hardware Available knob or lever operated Bolt through fixing from the inside for timber and metal doors up to 54mm thick Easily handed on site for left or right hand applications Tested for use on Fire Doors to EN Available with or without cylinder Cylinder supplied is 40mm Euro profile single cylinder SEU402 in polished nickel finish (can be supplied as part of a full master key suite if desired. Please contact us for further information) Lever option has key retention to ensure OAD is always secure SED990/KNC/SE SED996 on active leaf SC Satin Chrome plated (knob version only) SED900/LEC/SE Outside access device - Selector Rebated Door Applications Fire performance with OAD Timber Doors Steel Doors SED994 SED993 SED994 SED996 SED900/SE/LE Outside access device with lever operation - no cylinder SED900/SE/LEC Outside access device with lever operation - c/w cylinder SED990/SE/KN Outside access device with knob operation - no cylinder SED990/SE/KNC Outside access device with knob operation - c/w cylinder 95mm Active Leaf Active Leaf RH application shown 175mm 156mm active leaf active leaf 88mm 43mm 70mm SED994 on non-rebated door

10 17 Accessories for Panic & Emergency Exit Hardware 18 SED600/815 - Touch Bar Keeps For steel frame applications Keeps available for each latch on single, two or three point latching units. Supplied in silver finish as standard. Touch Bar Keeps For upvc frame applications Keeps available for each latch on single, two or three point latching units. Contact sales office for options. Supplied in white finish as standard. SED/032A - Vertical Bolt Keeps For steel frame applications Bottom keep and top trip/keep for use with vertical bolts on steel door frames. Supplied in silver finish as standard. SED999/S - Shoot tube, 1200mm lengths for use on doors over 2500mm. SED999/B - Connector used to connect two shoot tubes SED999/G - Shoot guide to conceal the joint between tubes. Please note: A complete set is required for extra high doors. AIGEW5700S Electromagnetic slimline lock with housing and built-in alarm. Must be used in conjunction with the micro switch slave unit, SED999/M or Touchbar unit with microswitch SED600/MS AST125-FLT Electric release for 72mm panic nightlatch (compatible with SED995 and SED996), 12v DC fail locked. Other electric releases are also available. Please ask for further details. SBL329.SP Mechanical digital lock providing external access for Push Bar latch or Push Pad latch devices. SBL369.SP Mechanical digital lock providing external access for Touch Bar latch, Push Bar latch or Push Pad latch devices. AHOEX204 Exit Guard door alarm unit, battery powered. Alarm signals unauthorised use of the exit. AHOEX206 Exit Guard door alarm unit, mains powered. ASULP5010DXKWL Heavy duty mechanical digital lock providing external access for Push Bar latch or Push Pad latch devices. With key override facility. Supplied to order only. Packers for steel doors, used to offset SED900 Series exit devices to ensure correct engagement with steel frames. Thickness - 3mm SED991PK - for SED991 & SED993 latches SED992PK - for SED992 & SED994 vertical bolts ALP101 Concealed power transfer loop for use with microswitch units used in conjunction with electromagnetic lock. Suitable for timber or steel frames. Accessories Selector Exit Device Ref: SED600/MS - Touch bar microswitch SED600/LE & LEC - OAD SED600/KN & KNC - OAD SED600/ES - Electric release SED990/KN & KNC - OAD SED900/LE & LEC - OAD SBL329.SP - Digital OAD SBL369.SP - Digital OAD ASULP5010DXKWL - Digital OAD SED999/M - Slave unit microswitch SLB154 (+SED999A) - Rim cylinder SEU402 - Cylinder for OADs SEU412 - Cylinder for nightlatches AHOEX204 - Door alarm (battery) AHOEX206 - Door alarm (mains) AIGEW5700S - Electromagnetic lock AST125-FLT - Electric strike SED999/B - Shoot tube connector SED999/G - Shoot guide SED999/S - Shoot tube SEU706-13mm Rebate kit for nightlatches SED991PK - Steel door packers SED992PK - Steel door packers Touch Bar Keeps - Steel frames Touch Bar Keeps - upvc frames Push Bar Keeps - Steel frames SED601 SEU402 - Single cylinder 40mm for use with OADs SEU412 - Single cylinder 45mm for use with nightlatches on 44mm thick doors (other sizes available to order) SLB154 - Rim cylinder for use with Push Bar latch or Push Pad latch devices to provide access from outside. Use with adapter (below). SED999/A - Adapter for use with rim cylinder. Converts rim cylinder for use with Push Bar latch or Push Pad latch devices. SED602 SED603 AEB800 SED991/ SED992/ SED993/ SED994/ SED995/ SED996/

11 19 CE s Explained EN1125:2008 and EN179:2008 Panic & Emergency Exit Hardware - Technical Data 20 EN1125: Panic Exit Applications Digit 1 - Category of Use Guarantees Standard Sizes All final escape doors which are used by members of the public are categorised as PANIC EXIT DOORS and must be fitted with escape hardware that has been certified to European Standard EN1125. The standard is for all push bar and touch bar devices which can be used in any environment open to members of the public and are distinct from Emergency Exit doors by virtue of the fact that they must provide "safe and effective escape through a doorway with minimum effort and without prior knowledge of operation". EN179: Emergency Exit Applications Applications where a final exit door is to be used only by trained personnel it is categorised as an EMERGENCY EXIT DOOR and must be certified to European Standard EN179. The standard is intended for such areas as places of work which are not accessible to members of the public and where the occupants are familiar with the layout and means of escape. Emergency Exit devices can be operated by push pads and lever handles. Only one category is identified:- 3 - High frequency use by public and others with little or no incentive to exercise care; e.g schools, areas of entertainment Digit 2 - Durability 6 - Tested up to 100,000 cycles 7 - Tested up to 200,000 cycles Digit 3 - Door Mass 5 - For doors up to 100kg 6 - For doors up to 200kg 7 - For doors over 200kg Digit 4 - Fire Resistance 0 - Not approved for use on Fire Doors A - Suitable for use on Smoke Door assemblies B - Suitable for use on Fire Doors - tested to EN To support the high quality engineering, durability and quality performance of the Securefast Panic & Emergency Exit Hardware we provide a 10 year guarantee against defects due to faulty manufacturing, workmanship or defective materials. The manufacturer agrees to replace any defective Securefast product free of charge provided the product has been fitted and maintained in accordance with the fitting instructions. Fixing/Installation - Touch Bar The Securefast Touch Bar hardware uses a series of mounting backplates for the end mechanisms and Pullman latches which are fixed to the surface of the door. The end mechanisms of the Touch Bar unit and Pullman latches are then mounted onto the backplates. A series of spacers are provided to take up any inaccuracies in the door. The Touch Bar is aluminium and can be easily cut on-site to suit the door width, with the ends being fully concealed by the end covers. Similarly, the vertical rods of the double and triple point latching units and the rod covers can be readily cut on-site to suit the door height with the cut ends of the covers being concealed inside the cast covers of the mechanism and Pullman latches. The latch bolts are adjustable to assist in achieving accurate alignment to ensure a smooth operation of the exit device and a positive fit of the door within the frame. Standard size units are tested on doors up to 2500mm high and 1300mm wide. The shoot bolts and the push bar can be cut down on-site to suit the door height and/or width. To comply with EN1125, the touch/push bar should be installed at a height between 900mm and 1100mm from finished floor level and the bar length must be at least 60% of the door opening width. When fitted at 1100mm the maximum door height is 2530mm on the standard range and 2750mm on the Touch bar range. Handing Details Touchbar Exit Devices All Securefast Touch Bar exit hardware is non handed and is suitable without alteration for left or right hand applications. Push Bar and Push Pad Devices Securefast Push Bar and Push Pad latches can be reversed on-site to suit left or right hand application. Vertical bolts are non handed. Single Doors The handing is defined by viewing the door from the pull side, as below. A door with hinges to the left viewed from the pull side is classified as a Left Hand door. Digit 5 - Safety & Coding System Under both standards, products are tested and classified in accordance with 10 fundamental criteria, culminating in a 10 digit code that must be displayed on the product packaging and on the product itself. Each digit represents a measure of how the product performs in each element of the testing or assessment criteria under the appropriate standard. Only the top grade is allowed on Panic & Emergency Exit Hardware 1 - Safety Digit 6 - Corrosion Resistance 3 - High resistance (96 hours salt spray tested to EN 1670) 4 - Very high resistance (240 hours salt spray tested to EN 1670) Digit 7 - Security for Products Fixing/Installation - Push Bar/Push Pad The hardware is surface mounted and supplied with full fixing instructions. To comply with the standards and guarantee, the push bars and shoot bolts which are supplied loose and must be cut down on-site to suit the door width and/or height. The top and bottom shoots (where applicable) allow for ±5mm of vertical adjustment. The cut ends of the push bar are concealed within the end boxes. Shoot bolt ends must be carefully cut on-site as the ends are visible. The Securefast range is supplied with all the necessary fixings for timber doors and allows for either self tapping or machine screws to be used on other door types. UK Left Hand ISO 6 UK Right Hand ISO 5 Double Doors The handing is defined by the first opening leaf (or active leaf). Using the same criteria as for a single door, if the hinges of the first opening leaf are to the left it is a Left Hand door. For EN N is the only grade allowed For EN N N N N The 4 grades are used to allow the opportunity for greater security as these devices are subject to testing with doors under greater pressure Digit 8 - Projection of Device Construction - Touch Bar The Touch Bar is extruded elliptical section aluminium. Aluminium vertical rods are concealed beneath aluminium covers. All box mechanisms, slave units and Pullman latch mechanisms are manufactured in galvanised steel with nickel plated latchbolts and painted cast Zamak cover casings. Outside access devices are cast Zamak and galvanised steel with die cast aluminium handle. UK Left Hand ISO 6 active leaf 1 - Large projection (less than 150mm from door face) 2 - Standard projection (less than 100mm from door face) active leaf Digit 9 - Type of Device Construction - Push Bar/Push Pad B B A The main body and slave unit is manufactured from die cast aluminium with extruded aluminium guides. The top and bottom shoots, the shoot ends and internal components are steel. The latchbolt is stainless steel. UK Right Hand ISO 5 [3] [6-7] [5-7] [0AB] [0/1] [3-4] [2] [1-2] [AB] [A-D] For example, our SED601 is classified with the code shown above. The numbers in brackets show the coding options identified within the standards. EN1125 A - Panic device using a Push Bar B - Panic device using a Touch Bar EN179 A - Emergency device using a Lever Handle B - Emergency device using a Push Pad Digit 10 - Field of Application A - Outward opening, single & double doors, active & inactive leaf B - Outward opening, single exit door only C - Outward opening, double exit door, inactive leaf only D (EN179 only) - Inward opening, single exit door only Fire Rating The Securefast range of panic and emergency exit devices is approved for use on timber and steel doors to EN1634-1:2000. However, it is important to recognise that the hardware is required for the initial part of a fire test until the door has become sealed into the frame. The fire door is then responsible for sealing off the area and therefore it is the door which will give the fire rating. Hold-Back Facility The touch bar range, push bar panic exit and push pad emergency exit devices are available with a hold-back feature incorporated into the mechanism unit which allows the bolts or latch to be held in the withdrawn position. This feature must not be specified on exit doors which are designated as fire doors unless the door has been fire rated in the unlatched condition.

12 21 Panic & Emergency Exit Hardware Summary 22 Select to suit application >> Panic Applications EN:1125:2008 Panic Applications EN:1125:2008 Emergency Applications EN:179:2008 SED601 SED602 SED603 AEB800 SED991 SED992 SED995 SED993 SED994 SED996 See Page No. >> CERTIFICATION BS EN1125:2008 BS EN179:2008 CE Marked FIRE RATING Timber Door - Single, Rebated & Non-Rebated Double Fitted with OAD Timber Door - Single, Rebated & Non-Rebated Double Fitted without OAD Timber or Steel Door - Single & Non-Rebated Double Fitted with outside cylinder Timber or Steel Door - Single & Non-Rebated Double Fitted without outside cylinder Steel Door - Single, Rebated & Non-Rebated Double Fitted with OAD Steel Door - Single & Non-Rebated Double Fitted without OAD 2 hour 4 hour 2 hour 4 hour 2 hour 4 hour 2 hour 4 hour OPERATION Push Pad Operator Push Bar Operator Touch Bar Operator Single Point Latching LATCHING Multi Point Latching Pullman Latching Single Door Applications DOOR TYPE Non-Rebated Double Door Applications Rebated Double Door - 1st Opening Leaf (active) Rebated Double Door - 2nd Opening Leaf (inactive) OUTSIDE ACCESS Outside Access Device with Knob or Lever Outside Access by Rim Cylinder Outside Access by Mechanical Digital Lock Outside Access by Euro Profile Cylinder

13 Our complete portfolio of product brochures can be obtained through our sales offices or can be downloaded from our website TateColson 1st Floor, Queen Anne House, 18 Eastbank Street, Southport, PR8 1DT Tel: (01704) Fax: (01704) Technical Support (01704) Unit 6, The Cedars Business Park, Avon Road, Cannock, Staffordshire WS11 1QJ Tel: (01543) Fax: (01543)