EMC TEST REPORT. Complied

Transcription

1

2 Page : 1 of 39 EMC TEST REPORT Test report No: Type of Equipment : Model Name: Variant Model Name: Applicant: Manufacturer #1: Manufacturer #2: EMC-CE-1338 CCTV CAMERA HD61X HD73X, CNB-D2750PVR, CNB-V1760PVR CNB Technology Inc. CNB Technology Inc. CNB Electronic (shenzhen) Co., Ltd Test standards : EN 55022:2006, Class A EN :1995+A1:1998+A2:2003 Testing Laboratory : Test result : Complied This product complies with the requirements of the EMC Directive 2004/108/EC. The results in this report apply only to the sample tested. This test report shall not be reproduced except in full, without the written approval of EMC compliance Laboratory. Receipt date: Date of testing: ~ Issued date: Tested by: Approved by: PARK, YONG-JIN CHUNG, MIN-SEOK

3 Page : 2 of 39 Contents 1. Applicant information Laboratory information Test system configuration Operation environment 3.2 Measurement Uncertainty 4. Description of E.U.T General information 4.2 Product description 4.3 Auxiliary equipments 4.4 Test configuration 4.5 Operating conditions 5. Summary of test results Modification to the E.U.T. 5.2 Summary of EMI emission test results 5.3 Summary of immunity test results 5.4 Performance criteria 6. Test results Radiated Emission 6.2 Electrostatic Discharge test result 6.3 Radio Frequency Electromagnetic Fields 6.4 Electric Fast Transient/BURST 6.5 Surge 6.6 Conducted Immunity 7. E.U.T. photographs

4 Page : 3 of Applicant information Applicant : CNB Technology Inc. Address : #701,star valley,60-11 Gasan-Dong, Geumcheon-Gu, Seoul, , Korea Telephone : Fax. : kira1227@cnbtec.com Contact name : LEE KI SUNG Manufacturer#1 : CNB Technology Inc. Address : #701,star valley,60-11 Gasan-Dong, Geumcheon-Gu, Seoul, , Korea Telephone : Fax. : kira1227@cnbtec.com Contact name : LEE KI SUNG Manufacturer#2 : CNB Electronic (Shenzhen) co., Ltd Address : 4~5/F.,4 Bldg kingwingtat technology industry Park gangtou village, buji town, long gang district Shenzhen,p.r.china Telephone : Fax. :

5 2. Laboratory information Page : 4 of 39 Address EMC compliance Ltd. Telephone Number : Facsimile Number : CBTL Testing Laboratory FCC Filing No.: FCC CAB.: KR0040 VCCI Registration No. : C-1713, R-2710, T-258 KOLAS NO.: 231 SITE MAP Yongin city EMC compliance

6 3. Test system configuration Page : 5 of Operation environment Temperature Humidity Pressure OATS : 19 C 40 % - Immunity area : 20 C 41 % 1000 hpa Test site These testing items were performed following locations; Semi-anechoic chamber: Radiated Emission #4(3m) OATS : Radiated Emission (10m) Anechoic chamber (3m) : RS Immunity area :, ESD, EFT/Burst, Surge, CS

7 3.2 Measurement Uncertainty Page : 6 of 39 All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are test receiver, cable loss, antenna factor calibration, Antenna directivity, antenna factor variation with height, antenna phase center variation, antenna frequency interpolation, measurement distance variation, site imperfection, mismatch, and system repeatability. Based on NIS 80, 81, the measurement uncertainty level with a 95% confidence level was applied. Radiated Emission measurement :(k=2, 95%) MHz ; 3 m: ±3.73 [db], 10 m: ±3.71 [db] MHz ; 3 m: ±3.81 [db], 10 m: ±3.80 [db] Radio Frequency Electromagnetic Fields :(k=2, 95%) ± [db]

8 Page : 7 of Description of E.U.T. 4.1 General information - HD61X is a CCTV camera. 4.2 Product description Type of product: Model name (Basic): CCTV CAMERA HD61X Model name (Variant): HD73X, CNB-D2750PVR, CNB-V1760PVR HD73X: High Resolution Difference: CNB-D2750PVR: CNB BRAND of HD61X CNB-V1760PVR: CNB BRAND of HD73X Serial no: - Trade name : - Testing Voltage: Product rating: Note : DC 12V DC 12V This test was done with HD61X.

9 4.3 Auxiliary equipments Page : 8 of 39 Type Model / Part # Serial number Manufacturer Monitor CX911MW N732H1IL900530W SAMSUNG DC power supply 6032A US HP 4.4 Test configuration

10 Page : 9 of 39 Type Description Connection (To) Spec. Length(m) Note * Signal Power Power supply (DC 12V) Non-Shield BNC cable Monitor Shield Operating conditions The EUT was configured as normal intended use. Test mode 1 Display mode. Normal operating

11 5. Summary of test results Page : 10 of Modification to the E.U.T. None 5.2 Summary of EMI emission test results Application Test method Test result Conducted emission EN Class A N/A Radiated emission EN Class A Complied Harmonics current EN :2006 N/A Voltage fluctuations and flickers EN :2005 N/A 5.3 Summary of immunity test results Items Application Test method Test result Electrostatic discharge Enclosure EN :1995+A1+A2:2001 Complied Radiated RF immunity Enclosure EN :1995+A1:2002 Complied Fast transient Surge Conducted RF immunity Magnetic field immunity Voltage dip/interruption DC 12V Signal DC 12V Signal DC 12V Signal EN :1995+A1+A2:2004 EN :1995+A1:2001 EN :1996+A1:2001 Complied Complied Complied Enclosure EN :1994+A1:2001 N/A DC 12V EN :2004 N/A Voltage variation DC 12V EN :2003 N/A

12 5.4 Performance criteria Page : 11 of 39 The variety and the diversity of the apparatus within the scope of this document makes it difficult to define precise criteria for the evaluation of the immunity test results. If as a result of the application of the tests defined in this standard, the apparatus becomes dangerous or unsafe then the apparatus shall be deemed to have failed the test. A functional description and a definition of performance by the manufacture and noted in the test report, based on the following criteria: Electrostatic discharge There shall be no damage, malfunction or change of status due to the conditioning. Flickering of an indicator during the application of discharge is permissible, providing which could be interpreted by associated equipment as a change, Radiated electromagnetic fields There shall be no damage, malfunction or change of status due to the conditioning. Flickering of an indicator during the application of discharge is permissible, providing which could be interpreted by associated equipment as a change, and no such Flickering of indicators occurs at a field strength of 3V/m. For components of CCTV systems, where the picture is allowed at 10V/m, providing. (a) there is no permanent damage or change to EUT (e.g. no corruption of memory or changes to programmable setting etc.) (b) at 3V/m, any deterioration of the picture is so minor that the system could still be used; and (c) there is no observable deterioration of the picture at 1V/m. Fast transient burst / slow high energy voltage surge There shall be no damage, malfunction or change of status due to the conditioning. Flickering of an indicator during the application of discharge is permissible, providing That there is no residual is permissible, providing that there is no residual change in the EUT or any change in outputs, which could be interpreted by associated equipment as a change, and no such flickering of indicators oeuvres at U=130dBuV. For components of CCTV systems, where the status is monitored by observing the TV picture, then deterioration of the picture is allowed at U=140dBuV, providing: (a) there is no permanent damage or change to the EUT (e.g. no corruption of memory or changes to programmable settings etc.):

13 Page : 12 of 39 (b) at U =130dBuV, any deterioration of the picture is so minor that the system could still be used; and (c) there in no observable deterioration of the picture at U +120dBuV. Conducted RF immunity There shall be no damage, malfunction or change of status due to the conditioning. Flickering of an indicator during the application of discharge is permissible, providing That there is no residual is permissible, providing that there is no residual change in the EUT or any change in outputs, which could be interpreted by associated equipment as a change, and no such flickering of indicators oeuvres at U=130DBuv. For component of CCTV systems, where the status is monitored by observing the TV picture, then deterioration of the picture is allowed at U=140dBuV, providing: (d) there is no permanent damage or change to the EUT (e.g. no corruption of memory or changes to programmable settings etc.): (e) at U =130dBuV, any deterioration of the picture is so minor that the system could still be used; and (f) there in no observable deterioration of the picture at U +120dBuV. Voltage dip/interruption There shall be no damage, malfunction or change of status due to the conditioning. Flickering of an indicator during the conditioning is permissible, providing that there is no residual change in the EUT or any change in outputs, which could be interpreted by associated equipment as a change. The EUT shall meet the acceptance criteria for the functional test, after the conditioning.

14 Page : 13 of Test results 6.1 Radiated Emission Test specification Test mode EN Sections 6, Class A Display mode. Date Power supply DC 12V Semi-anechoic chamber #4, Test facility 10m OATS Temperature ( C) 18 C Humidity (%) 39 % Remarks Complied Minimum limit margin is 1.00 db at MHz Limits of radiated emission measurement Frequency [MHz] Class A(dBuV/m)@10m Class B(dBuV/m)@10m Above 1000MHz Measurement procedure A pretest was performed at 3m distance in a semi-anechoic chamber for searching correct frequency. The final test was done at a 10m open area test site with a quasi-peak detector. EUT was placed on a non-metallic table height of 0.8m above the reference ground plane. Cables were folded back and forth forming a bundle 0.3m to 0.4m long and were hanged at a 0.4m height to the ground plane. Cables connected to EUT were fixed to cause maximum emission. Test was made with the antenna positioned in both the horizontal and vertical planes of polarization. The measurement antenna was varied in height above the conducting ground plane to obtain the maximum signal strength.

15 Page : 14 of Used equipments Equipment Model no. Serial no. Makers Next cal. date Test Receiver ESCI R&S TRILOG SUPER BROADBAND ANT VULB Schwarz beck Antenna Mast A109 N/A DAEIL - Used Turn Table TS25 N/A DAEIL - 10m OATS - - EMC Compliance Sample calculation The field strength is calculated adding the antenna Factor, cable loss and, Antenna pad adding, subtracting the amplifier gain from the measured reading. The sample calculation is as follow: FS = MR + AF + CL + AT -AG MR = Meter Reading AF = Antenna Factor CL = Cable Loss AP = Antenna Pad AG=Amplifier Gain If MR is 30dB, AF 12dB, CL 5dB, AP 10dB, AG 35dB The result (MR) is = 22dBuV/m

16 6.1.5 Photographs of test setup Page : 15 of 39

17 6.1.6 Radiated emission measurement result *3m Semi-anechoic chamber Pre-scan Data ( #4) -Horizontal Page : 16 of 39 -Vertical

18 *10m OATS measurement data Page : 17 of 39 Frequency Reading Pol. Correction Height angle Factor Limits Result Margin [MHz] [dbuv/m] [m] Antenna Cable [dbuv/m] [dbuv/m] [db] V V H V H V H H * Note : Reading = Test Receiver value,

19 6.2 Electrostatic Discharge test result Test specification Test level Discharge impedance Power supply EN :2001 Contact: ± 2, 4, 6 kv Air: ± 2, 4, 8 kv HCP / VCP : ± 2, 4, 6 kv 330 Ω/150 DC 12V Page : 18 of 39 Date Number of discharge 10 Interval between discharges : 1s Temperature( C) 20 C Humidity (%) 41% Pressure (mb) 1000 mb Remarks Complied - There was no change of operation status during above testing.(a1) - During the test, some of flickering phenomenon happened. After this test, EUT was operated normally.(c1, A2) Measurement procedure A ground reference plane was located on the floor, and connected to earth via a low Impedance connection. The return cable of the ESD generator was connected to the reference plane. In case of floor standing equipment, EUT was placed on the reference plane on 0.1 m of insulating Support. In case of table top equipment, EUT was placed on a wooden table 0.8m above the reference grounded floor. A horizontal coupling plane(hcp) was placed on the table, and Connected to the reference plane via a 470 resistor located in each end (0.5mm insulating support between EUT and HCP). In both cases a vertical coupling plane(vcp) OF 0.5 X 0.5m was located 10cm from the EUT s sides. The VCP was connected to the reference plane in the same matter as the HCP.

20 6.2.2 Used equipments Page : 19 of 39 Equipment Model No. Serial No. Makers Next Cal. Date ESD Tester PESD 1600 H HAEFELY HCP VCP Used Photographs of test setup

21 6.2.4 Measurement result Electrostatic Discharge (Test Point) Page : 20 of 39 Air discharge Contact discharge

22 Page : 21 of 39 Contact discharge Location(EUT) Applied level (±) Result C1 Screw ±2,4,6KV Complied HCP (All 4 sides) ±2,4,6KV Complied VCP (All 4 sides) ±2,4,6KV Complied Air discharge Location(EUT) Applied level(±) Result A1 EUT case ±2,4,8KV Complied A2 Power port ±2,4,8KV Complied

23 6.3 Radio Frequency Electromagnetic Fields Test specification EN :2002 Page : 22 of 39 Tested frequency Test level & Modulation Distance Dwell time Step size Power supply 80MHz 2000MHz log 1% step 1,3,10 Vrms, 80% Amplitude Modulation(1kHz) 1,3,10 Vrms, Pulse Modulation (1Hz (0.5s ON: 0.5 s OFF)) 3m from EUT to tip of antenna 3S 1% step DC 12V Date Temperature( C) 19 C Humidity (%) 40% Pressure (mb) 1002 mb Remarks Complied - There was no change of operation status during above testing.(1v) - During the test, some of flickering phenomenon happened. After this test, EUT was operated normally.(3v,10v) Measurement procedure The test was performed at 3m full anechoic chamber. For floor standing equipment, the EUT was standing on the floor. For tabletop equipment, the EUT was located on a wooden table 0.8m above the floor. The EUT was tested all sides, horizontal and vertical polarization. The field uniformity was calibrated for 1V/m, 3V/m, 10V/m Used equipments Equipment Model no. Serial no. Makers Next Cal. date Power meter PM AR Power sensor (with adapter) Power sensor (with adapter) PH AR PH AR Directional coupler DC AR Signal generator E4421B GB AGILENT Used

24 Page : 23 of 39 Amplifier 150W1000M AR Directional Coupler DC7144M AR Amplifier 60S1G3M AR BiconiLog Ant. LPDA ETS - BiconiLog Antenna 3142B 1786 EMCO - Field monitor SI TDK - Controller HD Deisel - Turn table DS 412S - Deisel - Antenna mast MA Deisel Photographs of test setup Measurement result Location(EUT) Antenna polarization Result Front side Horizontal Complied Vertical Complied Rear side Horizontal Complied Vertical Complied Left side Horizontal Complied Vertical Complied Right side Horizontal Complied Vertical Complied

25 6.4 Electric Fast Transient/BURST Page : 24 of 39 Test specification EN : 2004 Coupling Test level Repetition frequency Coupling time Power supply DC 12V,Signal: Clamp DC 12V : ± 1 kv Peak Signal : ± 1 kv Peak 5 khz, Tr/Th = 5/50nS 60s DC 12V Date Temperature( C) 20 C Humidity (%) 41% Pressure (mb) 1002 mb Remarks Complied - During the test, some of flickering phenomenon happened. After this test, EUT was operated normally Measurement procedure A ground reference plane was located on the floor. EFT generator was connected to reference ground plane via low impedance connection. For floor standing equipment, EUT was placed on a 0.1 m wooden table. For tabletop equipment, EUT was placed on a 0.8m above the ground reference plane. Test generator and coupling/decoupling network was placed on, and bounded to, the ground reference plane. When using the coupling clamp, the minimum distance between the coupling plates and all other conductive surfaces, except the ground reference plane beneath the coupling clamp, Shall be 0.5m Used equipments Equipment Model No. Serial No. Makers Next Cal. date Generator UCS 500 M6 V EM TEST Capacitive Coupling Clamp - - EM TEST - Used

26 6.4.3 Photographs of test setup Page : 25 of 39

27 6.4.4 Measurement result DC 12V Page : 26 of 39 EFT coupling point (+) (-) Result L(+) +1KV -1KV Complied N(-) +1KV -1KV Complied L-N +1KV -1KV Complied Signal EFT coupling point (+) (-) Result BNC cable +1KV -1KV Complied

28 6.5 Surge Page : 27 of 39 Test specification EN :2001 Coupling DC 12V Test level Surge pulse shape Coupling Impedance DC 12V: 0.5,1 KV Signal: 0.5,1 KV Tr/Th =1.2/50uS DC12V: 40Ω+0.5 Signal (BNC): Direct Angles 0,90,180,270 Number of surge & Coupling time Power supply 5T/1min DC 12V Date Temperature( C) 20 C Humidity (%) 41% Pressure (mb) 1001 mb Remarks Complied - During the test, some of flickering phenomenon happened. After this test, EUT was operated normally Measurement procedure A ground reference plane was located on the floor. SURGE generator was connected to reference ground plane via low impedance connection. For floor standing equipment, EUT was placed on a 0.8 m wooden table. For tabletop equipment, EUT was placed on a wooden table (0.8m) above the reference plane Used equipments Equipment Model No. Serial No. Makers Next Cal. date Generator UCS 500 M6 V EM TEST CDN CNV EM TEST - Used

29 6.5.3 Photographs of test setup Page : 28 of 39

30 6.5.4 Measurement result Page : 29 of 39 DC 12V Coupling point (+) (-) Result L-N +0.5,1KV -0.5,1KV Complied Signal Coupling point (+) (-) Result BNC cable +0.5,1KV -0.5,1KV Complied

31 6.6 Conducted Immunity Page : 30 of 39 Test specification EN :2001 Tested frequency Test level & Modulation Coupling method Step size Power supply 150 KHz 100 MHz 1% step 1,3,10 Vrms, 80% Amplitude Modulation(1kHz) 1,3,10 Vrms, Pulse Modulation (1Hz (0.5s ON: 0.5 s OFF)) DC 12V : M2 Signal : clamp 1% step DC 12V Date Temperature( C) 19 C Humidity (%) 40% Pressure (mb) 1002 mb Remarks Complied - There was no change of operation status during above testing.(1v) - During the test, some of flickering phenomenon happened. After this test, EUT was operated normally.(3v,10v) Measurement procedure A ground reference plane was located on the floor. The test was performed on a ground reference plane on a 0.1m wooden table. This test were performed using CDN for mains, clamp for signal and injection probe. The frequency range was swept from 150 khz to 100MHz.This frequency range was Modulated with 1 khz sine wave at 80%. The signal generators provided the modulated frequency at a 1% step size. The power and all network cable, I/O cables longer than 3m in length were tested.

32 6.6.2 Used equipments Page : 31 of 39 Equipment Model no. Serial no. Makers Next Cal. date CS generator CWS 500 C S1 V EM TEST Used CDN CDN M2/M EM TEST Attenuator MU918 MCE/WEINSCHEL EM Clamp KEMZ Schaffner EM Clamp KEMA Scahffner - Current probe MD720 W /M6/ 0068 Schaffner Photographs of test setup

33 Page : 32 of Measurement result Coupling point Coupling method Result Power CDN (M2) Complied BNC cable Clamp Complied

34 7. E.U.T. photographs Page : 33 of 39 Front View Rear View

35 Inside Page : 34 of 39

36 Main Board Page : 35 of 39

37 Power Board Page : 36 of 39

38 LED Board Page : 37 of 39

39 Lens Page : 38 of 39

40 SUB Board Page : 39 of 39