STEP 1 STEP 2 OEM PARTS REMOVAL. Note: This installation procedure is intended for vehicles without an EGR system.

Size: px
Start display at page:

Download "STEP 1 STEP 2 OEM PARTS REMOVAL. Note: This installation procedure is intended for vehicles without an EGR system."

Transcription

1

2 TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please H&S Motorsports support at OEM PARTS REMOVAL Note: This installation procedure is intended for vehicles without an EGR system. STEP 1 Disconnect the negative terminal connection from both batteries. STEP 2 Drain approximately 4-5 gallons from the primary cooling system using the drain port on the driver side lower portion of the radiator. If the coolant is fairly new and clean, use a clean container so the coolant can be reused. Tighten the drain port once the coolant is drained. 2 Turbo Kit - 6.7L Power Stroke

3 STEP 3 Remove the front passenger inner fender lining and set aside. STEP 4 Unplug the MAF sensor located on the factory air intake box and remove the OEM air intake box/piping. The OEM intake box assembly will be re-installed later. Note: Most aftermarket intake systems should be compatible with the H&S Motorsports turbo kit as well. Turbo Kit - 6.7L Power Stroke 3

4 step 4 continued STEP 5 Remove the bolt holding the engine and transmission oil dipstick tubes to the plastic intake manifold and unplug the MAP sensor electrical connection on top of the plastic intake manifold. Unclip any electrical harnesses or coolant hoses that are attached to the plastic intake manifold. STEP 6 Disconnect the plastic/rubber coolant hose from the metal coolant pipe by carefully pinching the grey/white portion of the plastic locking connector and pulling it apart. 4 Turbo Kit - 6.7L Power Stroke

5 step 6 continued STEP 7 Remove the 15 bolts retaining the plastic intake manifold and remove it from the vehicle. Removal clearances can be tight, but it is easiest to pull the passenger side of the manifold out first. Note: Removing the hot-side intercooler pipe first can also free up some extra space for the plastic intake manifold removal if necessary. Turbo Kit - 6.7L Power Stroke 5

6 STEP 8 On 2015 vehicles, this step is a bit more difficult due to the fact that most of the bolts in the plastic intake manifold cannot be pulled out of the plastic manifold completely. After removal, place clean rags inside the intake openings and be extremely careful to NOT drop any items down these chambers! STEP 9 Disconnect the Intake Air Temperature sensor harness from the OEM cold-side intercooler pipe and remove the OEM intercooler piping, both hot and cold side. The hot-side intercooler pipe to turbocharger connection has a metal locking ring that must be disengaged while pulling the pipe off of the turbocharger for removal. The cold-side intercooler pipe to aluminum intake connection has a large locking C-clip that must be removed completely before the pipe can be removed. 6 Turbo Kit - 6.7L Power Stroke

7 step 9 continued STEP 10 Loosen the air inlet clamps on factory turbo ( vehicles may have dual inlets). Unplug the throttle valve electrical connection and disconnect the crank case breather hose from the aluminum intake assembly. The crank case breather connection has a cam lock that must be rotated counter-clockwise for removal. Once the breather hose is disconnected, carefully rotate it towards the driver fender. If you have purchased a crank case breather removal kit (not required), now would be a good time to install that product onto your vehicle. Turbo Kit - 6.7L Power Stroke 7

8 STEP 11 Remove the 3 bolts from the aluminum intake assembly and remove the assembly from the vehicle. Note: It may be necessary to remove the throttle valve from the intake assembly to clear the fan shroud during removal. STEP 12 Remove the two bolts holding the metal coolant pipe to the engine and carefully slide it out of the aluminum thermostat housing to remove it. Set the coolant pipe and hardware aside for re-use later. On vehicles, slide the plastic retaining ring back on the turbo coolant feed line and remove the now exposed metal locking ring to disconnect the coolant line from the turbo. Note: Be careful not to lose this ring during removal and re-install it into the turbo once the coolant line is removed. 8 Turbo Kit - 6.7L Power Stroke

9 step 12 continued On 2015 vehicles, unbolt the metal coolant pipe from the top of the turbo to disconnect the coolant feed line from the turbo. STEP 13 Remove the spring clamp connecting the turbo coolant feed hose to the thermostat housing and remove the entire turbo coolant feed line. Turbo Kit - 6.7L Power Stroke 9

10 STEP 14 Unplug the VGT (Variable Geometry Turbocharger) electrical connection from the top of the turbo. On vehicles, disconnect the vacuum hose from the turbo wastegate and install the supplied plastic vacuum plug into the end of the previously disconnected wastegate hose. Re-route and zip-tie the wastegate hose away from hot/moving parts as it will not be re-used. STEP 15 Remove the bolts holding the turbo exhaust housing heat shield and remove the heat shield from the vehicle. Now is a good time to spray all exhaust V-band connections, intermediate exhaust pipe nuts, and exhaust manifold nuts with penetrating oil to aid in removal. 10 Turbo Kit - 6.7L Power Stroke

11 step 15 continued STEP 16 Disconnect the exhaust back-pressure sensor tube from the passenger side intermediate exhaust pipe. If applicable, unbolt the back-pressure sensor support bracket from the EGR cooler and set the back-pressure sensor aside for re-installation later. On 2015 vehicles, there may also be an EGT sensor located in the passenger side intermediate exhaust pipe. Unplug the electrical connection for this sensor, but leave the sensor installed in the pipe as it will be removed with the pipe (the sensor will not be re-installed). STEP 17 Remove the V-band clamp from the passenger side intermediate pipe and also remove the 3 nuts connecting the pipe to the exhaust manifold. Remove the passenger exhaust intermediate pipe from the vehicle. The OEM exhaust V-band clamps WILL be reused, do not damage or discard! Turbo Kit - 6.7L Power Stroke 11

12 step 17 continued STEP 18 The OEM downpipe is a 2-piece assembly. Underneath the vehicle, disconnect the 2 bolt downpipe-to-exhaust connection and fully loosen the clamp connecting the upper downpipe section to the lower downpipe section. On 2015 vehicles, remove the nut attaching the lower downpipe section to the passenger side cylinder head. Remove the lower downpipe section from the vehicle. With the lower section removed, it provides much easier access to a bolt that connects the upper downpipe section to the transmission bell-housing (especially on 2015 vehicles). Remove this bolt and disconnect the V-band connection on the OEM downpipe. Remove the upper downpipe section from the vehicle. 12 Turbo Kit - 6.7L Power Stroke

13 step 18 continued STEP 19 Remove the V-band clamp from the driver side exhaust intermediate pipe. It is NOT necessary to remove the intermediate pipe separately here, as it can be removed while still attached to the OEM exhaust manifold. Note: On some vehicles, it may be easier to access the v-band clamp through the passenger fender-well. STEP 20 Remove the 4 OEM turbocharger pedestal mounting bolts and set aside for re-use. Ensure there is nothing left connected to the turbocharger/pedestal assembly and lift the entire OEM turbocharger/pedestal assembly out of the vehicle. This can be made much easier with the help of another individual since the assembly is quite heavy and awkward. Remove the OEM pedestal gasket from the vehicle. Note: It may be helpful to soak the front guide-dowels on the pedestal with penetrating oil to aid in removal. Place a clean rag over the now exposed hole in the engine valley and be extremely careful to NOT drop any items down this cavity! Turbo Kit - 6.7L Power Stroke 13

14 step 20 continued STEP 21 Using brake cleaner and compressed air or other suitable media, clean the driver side high pressure outlet on the CP4 fuel pump. After cleaning, loosen and disconnect the nut on the high pressure line and loosen the two high pressure line hold down bolts as shown. Rotate the high pressure line towards rear of vehicle slightly. Moving this line will provide better access to the driver side top-front manifold nut. It is very important that no dirt or other contaminants get into the CP4 outlet or fuel line while it is disconnected! Possible pump or injector damage could occur! 14 Turbo Kit - 6.7L Power Stroke

15 step 21 continued STEP 22 If the vehicle is equipped with an EGT solution, unplug the EGT sensor harness and remove the sensor from the bung. The EGT sensor will be re-installed in one of the HSM exhaust manifolds later. Unbolt and remove the EGT solution plate and gasket (or regular block-off plate if applicable). Stuff a small rag into the now exposed exhaust port on the passenger exhaust manifold. STEP 23 Remove the bolts holding the manifold heat shields to the exhaust manifolds and remove the heat shields from the vehicle. Remove all 16 exhaust manifold nuts/spacers and remove the OEM exhaust manifolds from the vehicle. Retain the OEM exhaust manifold hardware for re-use. Note: The clearance between the driver side manifold and the fuel lines can be tight, be extremely careful not to apply excessive pressure to these fuel lines while disconnecting the hardware or removing the manifold. With the exhaust manifolds removed, the exhaust ports on the cylinder heads are now exposed! DO NOT drop anything into these ports! Turbo Kit - 6.7L Power Stroke 15

16 step 23 continued hsm parts installation STEP 24 If some of the exhaust manifold studs were pulled out of cylinder heads during the removal of the OEM exhaust manifolds, carefully remove the nuts from the studs and re-install the studs into the cylinder heads now. Ensure they bottom out correctly into the cylinder heads but DO NOT over-tighten as the cylinder heads are aluminum. 16 Turbo Kit - 6.7L Power Stroke

17 step 24 continued STEP 25 If you are not using a factory EGT solution, install the supplied plug into the appropriate location on the driver side HSM manifold. Using high temperature thread sealant, install the supplied 1/8 NPT to -5AN adapter into the side port near the rear of the passenger side manifold as shown. This connection will be used for the OEM back-pressure sensor. Each of the HSM exhaust manifolds has an extra 1/8 NPT port that can be used for extra sensors such as EGT or drive-pressure. Now is a good time to install these external sensors if applicable. If you will not be using any external sensors, apply anti-sieze and install the supplied 1/8 NPT plugs into the ports that you will not be using. If you are not using an external wastegate, also plug the wastegate port at this time with the supplied plug and clamp. Turbo Kit - 6.7L Power Stroke 17

18 step 25 continued STEP 26 Slide one of the previously removed OEM V-band clamps onto the driver side HSM exhaust manifold. It is best to orient the bolt of the V-band clamp facing UP as shown. Slide the other OEM V-band clamp onto the passenger side HSM manifold as well. STEP 27 Ensure the OEM exhaust manifold gaskets are in good condition. If they are not, please replace them with new OEM gaskets (not supplied). Starting with the driver side first, very loosely install the HSM exhaust manifolds into the vehicle using the OEM manifold hardware. Make sure the V-band clamps are oriented as shown during installation of the manifolds with the driver side clamp between the manifold flanges. On 2015 vehicles, be sure to install the thicker spacers on the rear studs of each manifold. Be careful not to pinch or crush the V-band clamps during installation. Do NOT fully tighten the manifold hardware at this time and ensure that the manifolds are still able to be moved slightly. 18 Turbo Kit - 6.7L Power Stroke

19 step 27 continued STEP 28 Clean and inspect the HSM pedestal assembly thoroughly to ensure no foreign materials are present in oil, coolant, or exhaust passages. Install the HSM intermediate exhaust pipes onto the HSM pedestal using the supplied two-bolt gaskets and (4) 8mm bolts as shown (the longer pipe needs to be installed on the passenger side). Torque these bolts to 22 lb/ft. Turbo Kit - 6.7L Power Stroke 19

20 STEP 29 Carefully install the HSM pedestal assembly into the vehicle using the new supplied OEM pedestal gasket and previously removed OEM bolts. Use the loose exhaust manifolds to your advantage when installing the pedestal assembly. Ensure that the pedestal is aligned correctly on the guide-dowels and that it is fully seated against the engine block before tightening hardware. Torque the pedestal bolts to 35 lb/ft. STEP 30 Starting with the driver side first, slide the OEM V-band clamps onto exhaust manifold to intermediate pipe connection points. Ensure the connection points are flush and that the machined flanges fit together well. Adjust the manifolds accordingly until the flanges fit together correctly and tighten the V-band clamps securely. Note: The V-band clamps can be a tight fit, so use the loose manifolds to your advantage while working the clamps into place. 20 Turbo Kit - 6.7L Power Stroke

21 step 30 continued STEP 31 Ensure that the manifold and pedestal assembly are aligned correctly and no potential exhaust leaks or other issues can be found. Torque the exhaust manifold mounting hardware to 25 lb/ft. Turbo Kit - 6.7L Power Stroke 21

22 STEP 32 Re-install the previously removed high pressure fuel line onto the CP4 pump, tighten the nut and line support hardware. STEP 33 Carefully slide the supplied HSM downpipe into its approximate location from the top. It will be connected at a later time. STEP 34 Install the previously removed OEM back-pressure sensor onto the 1/8 NPT to -5AN adapter on the passenger side HSM exhaust manifold and tighten securely. On vehicles, the OEM back-pressure mounting bracket can be bent to connect to the original location on the EGR cooler assembly if applicable. Make sure the back-pressure sensor electrical connection is secure and fasten the OEM VGT electrical connection away from heat using zip ties. 22 Turbo Kit - 6.7L Power Stroke

23 STEP 35 Locate the HSM turbine flange adapter, adapter gasket, and (6) 5/16 x 5/8 stainless bolts. Install the turbine flange adapter onto HSM turbocharger and tighten hardware to 25 lb/ft. STEP 36 Clean the turbo oil drain surface and install the supplied HSM oil drain adapter onto your HSM turbocharger assembly using the supplied gasket and (2) 3/8 12-point flange bolts as shown. Note: The oil drain is not centered on the adapter. The drain needs to be offset TOWARDS the DRIVER side as shown. Apply some assembly grease or clean engine oil to the supplied rubber oil drain fitting and push it into the bottom of the oil drain adapter, leaving the more tapered end of the rubber fitting protruding from the adapter. Ensure your oil drain fitting is not damaged and will make a leak-free seal. Turbo Kit - 6.7L Power Stroke 23

24 step 36 continued STEP 37 Install two of the supplied pedestal studs into the top two holes on the pedestal and slide the supplied T4 flange gasket onto the HSM pedestal. Apply assembly grease or clean engine oil to the rubber oil drain fitting and also to the oil drain hole on the pedestal. VERY carefully install the turbocharger assembly onto the HSM pedestal by rotating the turbocharger counter-clockwise to get the oil drain fitting started in the pedestal before SLOWLY lowering the turbocharger onto the two pedestal studs. Ensure that as the turbo slides onto the studs and that the oil drain adapter is aligned correctly in the pedestal. If the rubber oil drain adapter is damaged during installation, it must be replaced. 24 Turbo Kit - 6.7L Power Stroke

25 STEP 38 Install the two remaining studs in the pedestal and fasten the turbo assembly to the pedestal using the supplied 3/8 flange nuts. Tighten these nuts to 30 lb/ft. Note: A short 9/16 wrench will be the easiest way to tighten the driver side mounting nuts as they are a very tight fit. The passenger side nuts can be easily reached with a ratchet and extension. STEP 39 Using the supplied downpipe V-band clamp, connect the supplied upper downpipe section to the previously installed turbine housing adapter on the turbo. Leave this connection slightly loose at this time. Slide the supplied flat-band clamp onto the lower downpipe section as shown and then slide the lower downpipe section onto the upper downpipe section. Note: It may be necessary to temporarily strap the exhaust system towards the rear of the vehicle in order to provide room for the lower downpipe section. Turbo Kit - 6.7L Power Stroke 25

26 step 39 continued Loosely bolt the lower downpipe section to the exhaust system using the supplied hardware. STEP 40 Adjust the upper downpipe section so that it is not coming in contact with the exhaust manifold or firewall and tighten the V-band clamp at the turbo. A gap of about 1/8 between the manifold and downpipe is ideal. Tighten the 2-bolt ball flange and flat-band clamp while ensuring that the downpipe or exhaust system is not making contact with the firewall or any other part of the vehicle. Note: If you are using an external wastegate, now would be a good time to make the necessary connections to the downpipe if desired. 26 Turbo Kit - 6.7L Power Stroke

27 step 40 continued STEP 41 Clean/ inspect the supplied oil feed line to ensure that it is free of debris and install it between pedestal oil fitting (passenger side fitting, marked O for OIL) and turbo oil feed fitting on top of the turbocharger center section. Route the oil feed line in a manner so that it does not interfere with any other parts and is away from heat as shown. Double check that the oil feed line is connected to the correct PASSENGER SIDE fitting on the HSM pedestal! Connecting it to the incorrect port will almost certainly result in turbocharger damage and possibly other engine damage! Turbo Kit - 6.7L Power Stroke 27

28 step 41 continued STEP 42 Using the supplied 3/8 hose clamp, install the supplied coolant hose between the pedestal coolant fitting (driver side fitting) and factory thermostat housing as shown. If you are using an EGT solution, install the previously removed EGT sensor into the appropriate port on the driver side exhaust manifold and plug in the EGT sensor electrical connection. 28 Turbo Kit - 6.7L Power Stroke

29 step 42 continued STEP 43 Remove the rubber gaskets from the OEM plastic intake manifold and wipe any oil or debris from them using a clean rag. Install the rubber gaskets into the gasket locations on the HSM intake manifold assembly. The HSM intake manifold assembly has two extra 1/8 NPT ports. Plug any un-used 1/8 NPT ports with the supplied plugs and teflon tape. Turbo Kit - 6.7L Power Stroke 29

30 STEP 44 Clean the OEM intake manifold flange surfaces before installing the HSM intake manifold and supplied dipstick bracket with the supplied (8) M6 x 25 flange bolts. The dipstick bracket will be mounted to the driver rear manifold bolt as shown. Tighten the intake manifold hardware to 12 lb/ft. Note: The clearance between the turbo compressor housing and firewall is tight. The easiest method to install the intake manifold is by sliding the driver side in first, then work the passenger side between the turbo and firewall. STEP 45 Attach the engine and transmission oil dipsticks to the previously installed dipstick bracket using the supplied 1/4 hardware as shown. 30 Turbo Kit - 6.7L Power Stroke

31 step 45 continued STEP 46 Remove the MAP sensor from the OEM plastic intake manifold and clean any oil/debris from it using a clean rag. Apply a small amount of assembly grease or clean engine oil to the MAP sensor O-ring and install the MAP sensor into the HSM intake manifold using the supplied M10 x 32 button-head allen bolt. Reconnect the MAP sensor electrical connection. STEP 47 Apply a small amount of assembly grease or clean engine oil to the O-ring on the previously removed OEM metal coolant pipe and re-install it in the factory location. Securely fasten the pipe using the OEM hardware and reconnect the plastic locking connection on the OEM coolant hose. Turbo Kit - 6.7L Power Stroke 31

32 step 47 continued STEP 48 Re-install the factory air intake box (or aftermarket if applicable) using the previously removed factory hardware and reconnect the MAF sensor. Locate the HSM 4 intake pipe, 20-degree 4 ID boot, 4.25 ID to 4 ID straight boot, and (4) 4 worm-gear clamps. Install the HSM intake pipe assembly with the 20-degree boot on the turbocharger and the straight adapter boot on factory air box as shown. Clock the boots and pipe to ensure that there is adequate clearance on all parts before tightening the clamps. The intake pipe needs to sit as low as possible without coming in contact with the thermostat housing. Note: The 4.25 ID end of the straight adapter boot will be installed on the factory air intake box, and the 4 ID end on the metal intake pipe. 32 Turbo Kit - 6.7L Power Stroke

33 step 48 continued STEP 49 If you chose NOT to remove factory crank case breather assembly, locate the supplied HSM breather hose adapter and push it into factory breather hose until it locks into place as shown. Using the supplied 5/8 rubber hose, push the hose onto the end of the HSM breather hose adapter (no clamp is necessary here since it will not be seeing any pressure). Route the hose toward the driver side inner fender-well and down under the vehicle to a location away from any hot or moving parts. Make sure the hose is not kinked or pinched and zip-tie in a desired location. Note: You may need to unclip the crank breather electrical harness from the nearby bracket to provide more slack for routing. Turbo Kit - 6.7L Power Stroke 33

34 step 49 continued STEP 50 Install the supplied HSM power steering reservoir relocation bracket as shown using the supplied 1/4 hardware and OEM bolt. 34 Turbo Kit - 6.7L Power Stroke

35 STEP 51 Since the intercooler is now reverse-flow, the wiring harness for the charge air temperature sensor must be moved from the OEM location to up near the oil fill location. The wire can be un-clipped (3 clips) from the fan shroud and re-routed using zip-ties. Zip-tie the harness to the lower power-steering reservoir hose as shown and route the wiring away from the serpentine belt and other moving or hot parts to ensure it will not be damaged. STEP 52 Remove the charge air temperature sensor from the OEM intercooler piping by carefully disengage small locking tab while twisting the sensor counter-clockwise. Clean the sensor of any oil/debris and install it into the supplied HSM cold-side intercooler pipe with a small amount of assembly grease or clean engine oil on the O-ring to aid in installation and prevent damage. Ensure the sensor is fully locked into place as shown. Turbo Kit - 6.7L Power Stroke 35

36 step 52 continued STEP 53 The HSM cold-side intercooler pipe has two extra 1/8 NPT ports. Plug any un-used ports with the supplied plugs and teflon tape. Thoroughly clean the intercooler clamp locations on the OEM intercooler before using the supplied 60-degree 3 ID boot, straight 3 ID boot, and (4) T-bolt clamps to install the cold-side intercooler pipe onto the vehicle as shown. Be careful not to damage the charge air temperature sensor during installation. Position the pipe as shown and ensure that the pipe and boot are fully seated against the intercooler before tightening all connections. Note: We recommended using glass cleaner on all boot connections for ease of install and a clean connection surface. 36 Turbo Kit - 6.7L Power Stroke

37 step 53 continued STEP 54 Plug in the charge air temperature sensor to the previously re-routed wiring harness. STEP 55 Install the supplied HSM hot-side intercooler pipe using the supplied 60-degree 3 ID boot, 90-degree 3 ID boot, and (4) T-bolt clamps. The 90-degree boot will be used on the intercooler. Position the pipe as shown and tighten the clamps securely. Turbo Kit - 6.7L Power Stroke 37

38 step 55 continued STEP 56 Refill the coolant system with the recommended coolant and reconnect the negative battery terminals. Reinstall the passenger inner fender lining. 38 Turbo Kit - 6.7L Power Stroke

39 STEP 57 If required, install the proper H&S Motorsports tuning calibration(s) onto your vehicle. See for more information. STEP 58 Start the vehicle and check for any fuel, oil, coolant, exhaust, or air leaks. Bleed coolant system and add additional coolant as necessary. STEP 59 ENJOY THE BEST 6.7L POWERSTROKE TURBOCHARGER KIT ON THE MARKET! Turbo Kit - 6.7L Power Stroke 39

40

This kit may void factory warranty please check with manufacturer.

This kit may void factory warranty please check with manufacturer. Mfg Company TM Thank you for purchasing a Sinister Manufacturing Company EGR delete kit. Precision manufactured using aircraft quality 304 stainless steel and billet aluminum; this EGR kit is designed

More information

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION 303-01C-1 REMOVAL AND INSTALLATION Engine Body On Special Tool(s) Adapter For 303-D043 303-D043-02 or equivalent Special Tool(s) 303-01C-1 Turbocharger Lifting Bracket 303-1266 Wrench, Fan Clutch Nut 303-214

More information

Solstice/Sky Water Pump Replacement

Solstice/Sky Water Pump Replacement Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the

More information

Figure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top.

Figure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top. Here are some pictures to show what s required when replacing the A/C compressor, expansion valve and receiver/drier on a 2001 Volvo V70. Even if you don t replace these A/C parts these pictures can help

More information

Turbocharger system components, servicing

Turbocharger system components, servicing 21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners

More information

Before installation it is important to know what parts you have and what the capabilities of these parts are.

Before installation it is important to know what parts you have and what the capabilities of these parts are. INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With

More information

COOLING SYSTEM Section Page

COOLING SYSTEM Section Page 5 COOLING SYSTEM Section Page 5.1 COOLANT PRE-HEATER... 5-3 5.2 COOLANT PUMP NON-EGR ENGINE... 5-7 5.3 COOLANT PUMP EGR ENGINE... 5-13 5.4 FRONT CONNECTOR HOUSING NON-EGR ENGINE... 5-17 5.5 FRONT CONNECTOR

More information

2003 ACCORD - Automatic Transmission Removal

2003 ACCORD - Automatic Transmission Removal 2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special

More information

P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc

P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center

More information

M-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS

M-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

Cooling system components, removing and installing

Cooling system components, removing and installing Engine BHW Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! When doing any repair work, especially in the engine compartment,

More information

Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks

Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended

More information

INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5

INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to

More information

TITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V

TITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended

More information

ENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER...

ENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER... FUEL FILTER............................ FUEL HEATER.......................... INJECTOR.............................. SUPPLY PUMP.......................... COMMON RAIL.......................... FUEL PRESSURE

More information

Cooling system components, removing and installing

Cooling system components, removing and installing Page 1 of 34 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate

More information

Katana Supercharger Installation Instructions Rev. E Page 1 of 23

Katana Supercharger Installation Instructions Rev. E Page 1 of 23 Katana Supercharger Installation Instructions Rev. E Page 1 of 23 READ FITTING INSTRUCTIONS IN FULL BEFORE INSTALLATION This article is sold without warranty expressed or implied. No warranty or representation

More information

Installing a new 928 Motorsports All-Aluminum Radiator

Installing a new 928 Motorsports All-Aluminum Radiator 928 Motorsports Supercharger Installation Copyright 2008, 928 Motorsports, LLC All Rights Reserved Installing a new 928 Motorsports All-Aluminum Radiator Copyright 2008 928 Motorsports, LLC. Toll-Free

More information

INSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES

INSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY

More information

Intake Manifold: Service and Repair

Intake Manifold: Service and Repair 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 Copyright 2008, ALLDATA 9.90 Page 1 Intake Manifold: Service and Repair Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement.

More information

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER 14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------

More information

SCION FR-S 2013 - PERFORMANCE AIR INTAKE Preparation 2.0L F-4

SCION FR-S 2013 - PERFORMANCE AIR INTAKE Preparation 2.0L F-4 Preparation 2.0L F-4 Part Number: PTR03-18130 Please see Page 12 for important Care and Maintenance information! Kit Contents Item # Qty. Service Part # Description 1 1 PTR03-18130-AC TRD Air Box Base

More information

with installation dynafact boost GAUGE this manual is for use with systems 64050-64054

with installation dynafact boost GAUGE this manual is for use with systems 64050-64054 owners manual with installation instructions dynafact boost GAUGE this manual is for use with systems 64050-64054 GENERAL INSTALLATION PRACTICES This manual is an installation guide for all 1. Banks DynaFact

More information

INSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)

INSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE

More information

www.servicechamp.com

www.servicechamp.com 1-800-221-0216 Fax: 1-800-472-2281 www.servicechamp.com Service Champ Part 52081 Service Interval every 30,000 miles / Chevrolet 1992-2002 6.5 liter Description and Operation The fuel filter element separates

More information

Slide the new steering column shaft through the steering column from the driver compartment.

Slide the new steering column shaft through the steering column from the driver compartment. Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.

More information

Actuator-Swirl Valve DESCRIPTION

Actuator-Swirl Valve DESCRIPTION US/Canadian 2007 Sprinter Diesel V6 Dodge Service Manual Swirl Valve Info Actuator-Swirl Valve DESCRIPTION The swirl valve linkage links the swirl valves in the intake manifold to the swirl valve actuator.

More information

Oregon Fuel Injection

Oregon Fuel Injection Corporate Office: P.O. Box 21121, VE Pump Removal and Installation Cummins Lock Timed Applications Removal Clean the exterior of the injection pump and mounting surfaces. 1. Disconnect the fuel return

More information

SALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT

SALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT SALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT INSTALLATION MANUAL: 2005 MUSTANG 4.6 3V MANUAL P/N: 10-8002-C14338C SUPERCHARGER KIT P/N: 10-1607-B14083* Saleen Performance, Inc. 1225 East Maple Rd.,

More information

Cooling system components

Cooling system components Page 1 / 33 19-1 Cooling system components Caution! When doing any repair work, especially in the engine compartment, pay attention to the following due to clearance issues: Route lines of all types (e.g.

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS. 2012-2015 BMW 335i 3.0L

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS. 2012-2015 BMW 335i 3.0L Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS 2012-2015 BMW 335i 3.0L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2057DK AIR FILTER 1 2 9-0442 TUBE;

More information

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 INSTALLATION GUIDE Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 Take every precaution to make this installation a safe procedure. Make safety the number

More information

VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS

VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS Tools required: 10mm/13mm socket and 3/8 drive ratchet with extension Torx T20/25/30 screwdrivers or bits Phillips head screwdriver,

More information

Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer

Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer Overview READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION PARTS LIST A. Flush valve B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve

More information

XL PREMIUM OIL COOLER KIT

XL PREMIUM OIL COOLER KIT -J05 REV. 0-0-0 XL PREMIUM OIL COOLER KIT GENERAL Kit Number 0008 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English

More information

Installation instruction do88 Intercooler for Volvo S40 / V50 / C30

Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At

More information

Cylinder head gasket, replacement

Cylinder head gasket, replacement "VCC065612 EN 20110604" 1(7) Cylinder head gasket, replacement Special tools: 999 5098 Disconnect battery earth lead Drain coolant Remove heat shield over exhaust manifold. (Only the two bottom bolts on

More information

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new

More information

How To Fix A Car With A Carbide Engine

How To Fix A Car With A Carbide Engine Section 12 Adjustment, Repair, and Replacement Page 12-1 Section 12 Adjustment, Repair and Replacement Section Contents Page Overview...12-5 Belts Belt Guard Removal/Installation...12-7 Belt Removal/Installation...12-11

More information

2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net

2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.

More information

Cooling system components, removing and installing

Cooling system components, removing and installing Page 1 of 30 19-1 Cooling system components, removing and installing Notes: When the engine is warm the cooling system is under pressure. If necessary release pressure before commencing repair work. Secure

More information

COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011

COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 Below are instructions for the Mini Mania Pulley Upgrade Kit, Part Number NME5011. Please take all necessary precautions for working

More information

SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3

SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3 PART #50190 SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER

More information

INSTALLATION MANUAL MODEL RP-100

INSTALLATION MANUAL MODEL RP-100 INSTALLATION MANUAL FOR 24 VALVE 5.9L CUMMINS POWERED DODGE TRUCKS 2003 THROUGH 2004.5 MODEL RP-100 READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 5400 BUSINESS 50 WEST SUITE 8 573 635-0555

More information

specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP

specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47) 47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing

More information

This kit may void factory warranty please check with manufacturer.

This kit may void factory warranty please check with manufacturer. Thank you for purchasing a Sinister Manufacturing Company EGR delete kit. Precision manufactured using the highest grade 304 stainless steel and 6061 billet aluminum; this EGR kit is designed to endure

More information

Volkswagen Golf 5 2004-> VW Rabbit GTI 2006->

Volkswagen Golf 5 2004-> VW Rabbit GTI 2006-> Стр. 1 из 24 Volkswagen Golf 5 2004-> VW Rabbit GTI 2006-> 19-1 Cooling system components Warning! Hot steam may escape when opening expansion tank. Wear protective goggles and protective clothing to prevent

More information

SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT

SCREAMIN' EAGLE HEAVY BREATHER PERFORMANCE AIR CLEANER KIT REV. 05-04- SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 95-08B, 9006-09B, 876-0A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories

More information

MAN - MERCEDES - BENZ

MAN - MERCEDES - BENZ SAYFA: 1 10100 10102 10103 355 353 06 15 355 353 03 15 346 353 08 15 AXLE GEAR AXLE GEAR AXLE (WITH BUSHING TYPE) (WITH BUSHING TYPE) (WITH BUSHING TYPE) 2521 2517-2521-2622 10104 10105 10106 308 350 00

More information

16 March 2015 1045440-2003-2007 r700 Dodge Cummins Primary Upgrade (I-00279) 1 P/N# 1045440

16 March 2015 1045440-2003-2007 r700 Dodge Cummins Primary Upgrade (I-00279) 1 P/N# 1045440 16 March 2015 1045440-2003-2007 r700 Dodge Cummins Primary Upgrade (I-00279) 1 Dodge Cummins (2003-07) R700 Primary Turbocharger Upgrade Kit P/N# 1045440 - Installation Manual - Please read all instructions

More information

Cooling system components, removing and installing

Cooling system components, removing and installing Volkswagen Touareg 3.2 - Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! Hot steam may escape when opening expansion tank.

More information

STEERING SYSTEM - POWER

STEERING SYSTEM - POWER STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and

More information

PUMP MAINTENANCE SCHEDULE AND CHECKLISTS

PUMP MAINTENANCE SCHEDULE AND CHECKLISTS PUMP MAINTENANCE SCHEDULE AND CHECKLISTS Providing a maintenance schedule defined specifically by run hours or yardage pumped serves only as a general guideline given the large amount of variables a unit

More information

Instruction Manual. Please read the manual carefully before installing and using this product. This product is for off road use only.

Instruction Manual. Please read the manual carefully before installing and using this product. This product is for off road use only. Instruction Manual Please read the manual carefully before installing and using this product. This product is for off road use only. PARTS 1. LIST BLOW OFF VALVE 1 5. GASKET 1 2. VACUUM HOSE 4.5φ 1 6.

More information

INSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05

INSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05 INSTRUCTIONS -J04 REV. 0-9-04 General FLHR/C/S (Road King) FRONT END LOWERING KIT This kit is designed for installation on 00 and later FLHR/C/S Model Motorcycles. Road King models use the conventional

More information

1 5 05-12 5 05-12. Additions, Revisions, or Updates

1 5 05-12 5 05-12. Additions, Revisions, or Updates 5 05-12 1 5 05-12 SUBJECT DATE Cylinder Head May 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0023 EPA04 MBE 4000 Cylinder Head Additional

More information

2011-14 F250 6 RADIUS ARM KIT

2011-14 F250 6 RADIUS ARM KIT 92154000 Thank you for choosing Rough Country for your suspension needs. 2011-14 F250 6 RADIUS ARM KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

MFH-5057 Ford Small-Block V-8 Fresh Water Cooling Kit Instructions

MFH-5057 Ford Small-Block V-8 Fresh Water Cooling Kit Instructions MFH-5057 Ford Small-Block V-8 Fresh Water Cooling Kit Instructions MONITOR PRODUCTS, INC. 15400 Flight Path Dr Brooksville, FL 34604 Tel: 1-800-334-4591 or 352-544-2620 Sales: ext 201 Technical Support:

More information

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware

More information

Section 7 Adjustment, Repair and Replacement

Section 7 Adjustment, Repair and Replacement Section 7 Adjustment, Repair, and Replacement Page 7-1 Section 7 Adjustment, Repair and Replacement Section Contents Page Overview...7-5 Belts Belt Guard Removal/Installation...7-7 Belt Removal/Installation...7-11

More information

Cooling system components, servicing

Cooling system components, servicing 19-1 Cooling system components, servicing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate protection, cover the cap

More information

Installation Instructions 4508 4508S

Installation Instructions 4508 4508S SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect

More information

Not required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided)

Not required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided) ELECTRIC FUEL PUMPS P/N 12-801-1, 712-801-1, 12-802-1, 712-802-1, 12-815-1, & 712-815-1 FUEL PRESSURE REGULATORS P/N 12-803, 12-501, 12-804, 12-500, & 15812NOS Installation Instructions THESE INSTRUCTIONS

More information

16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1

16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 Dodge 1500 4WD Model 1994-2001 P/N# 1032011-F

More information

BUGGY SETUP GUIDE. Volume GOKARTSUSA GY6 150, CN250. Buggy Setup Guide

BUGGY SETUP GUIDE. Volume GOKARTSUSA GY6 150, CN250. Buggy Setup Guide BUGGY SETUP GUIDE Volume 1 GOKARTSUSA GY6 150, CN250 Buggy Setup Guide GY6 150, CN250 DUNE BUGGY Buggy Setup Guide GOKARTSUSA.COM 2000 Highway 50 S. Lake Tahoe, CA 96150 Phone 800.603.1437 2 Table of Contents

More information

3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE

3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE 4 3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE A. Changing the Control Board B. Replacing a Heating Element C. Thermistor Replacement D. High Limit Switch Replacement E. Level Detector Replacement

More information

M-9000-ZX3 JRSC Focus Big Boost Upgrade Kit INSTALLATION INSTRUCTIONS

M-9000-ZX3 JRSC Focus Big Boost Upgrade Kit INSTALLATION INSTRUCTIONS Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: These instructions

More information

FRONT TURN SIGNAL RELOCATION KIT

FRONT TURN SIGNAL RELOCATION KIT -J0 REV. 00-0-0 FRONT TURN SIGNAL RELOCATION KIT GENERAL Kit Number -0 Models This kit fits 00 and later Dyna model motorcycles (except FXDSE), relocating the front turn signal from the handlebars to the

More information

http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html

http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -

More information

EM 58. 19. REMOVE NO. 2 MANIFOLD STAY (a) Remove the bolt, nut and stay.

EM 58. 19. REMOVE NO. 2 MANIFOLD STAY (a) Remove the bolt, nut and stay. 57 ROVAL 1. DISCHARGE FUEL SYST PRESSURE (See page FU-9) 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual

More information

The Ford Model A Water Pump

The Ford Model A Water Pump The Ford Model A Water Pump George Washington Chapter, Inc. 3903 Old Lee Highway Fairfax, VA 22030 1 Table of Contents Introduction/Specifications.. 3 1. Water Pump Inspection and Removal. 4 a. Removal..

More information

CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6

CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize

More information

Volkswagen B3 Passat General-Engine 4 CYL. 19 Engine - Cooling System (Page GR-19)

Volkswagen B3 Passat General-Engine 4 CYL. 19 Engine - Cooling System (Page GR-19) 19 Engine - Cooling System (Page GR-19) Cooling system draining and filling general information Body components, layout Engine components, layout Radiator fan run-on checking Recommended mixture ratios

More information

INSTALLATION MANUAL MODEL RP-150

INSTALLATION MANUAL MODEL RP-150 INSTALLATION MANUAL FOR 24 VALVE 5.9L CUMMINS POWERED DODGE TRUCKS 2003 THROUGH 2004.5 MODEL RP-150 READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 5400 BUSINESS 50 WEST SUITE 8 573 635-0555

More information

ReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD

ReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD SAFETY WARNING: recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks

More information

AWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T

AWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T AWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T Congratulations on your purchase of the AWE Tuning Intercoolers for your 2.7T Audi. Hundreds of hours of design and operational testing were spent

More information

2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure

2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure 2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure Derek Guenther 1/28/2015 Rev. Purpose The purpose of this document is to describe the procedure necessary to replace one of the ball nuts

More information

http://www.passatworld.com/forums/showthread.php?t=166611

http://www.passatworld.com/forums/showthread.php?t=166611 Page 1 of 6 For advertising info, email us! Home Forums Passat of the Month Marketplace About Us Passat World Forums > Passat Discussion > Club B5 > B5 Information-Base 1.8T Waterpump/Thermostat Replacement

More information

A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS

A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.

More information

Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna)

Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna) Installation Instructions Reverse Gear MAMBA (Monoblock for Cable operated) Read and become familiar with these installation instructions before start. Two Piece for H-D 5 Speed Trans., Cable operated

More information

Front brakes (FN- 3), servicing

Front brakes (FN- 3), servicing j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly

More information

CHROME FRONT BRAKE MASTER CYLINDER KIT

CHROME FRONT BRAKE MASTER CYLINDER KIT -J075 REV. 009-0-0 CHROME FRONT BRAKE MASTER CYLINDER KIT GENERAL Kit Number 5-99D, 5-99D Models These Chrome Master Cylinder Kits are designed to replace the original equipment front brake master cylinder

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-475B (Blue Finish) 21-475C (Gun Metal Grey Finish) 21-475P (Vacuum Metalized Chrome-VMC) 21-475R (Red Finish)

More information

Installation Guide 2010 BMW S1000RR Full Exhaust System

Installation Guide 2010 BMW S1000RR Full Exhaust System Installation Guide 2010 BMW S1000RR Full Exhaust System!! THIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE!! Congratulations on the purchase of your new TaylorMade

More information

11. COOLING SYSTEM 11-0 COOLING SYSTEM BET & WIN 50

11. COOLING SYSTEM 11-0 COOLING SYSTEM BET & WIN 50 11 COOLING SYSTEM SERVICE INFORMATION------------------------------------------------ 11-1 TROUBLESHOOTING----------------------------------------------------- 11-1 RADIATOR ------------------------------------------------------------------

More information

Ford F-250 / 350 2-1/2 Coil Kit. Ford F-250, F350 2011-2015. Part#: 013255

Ford F-250 / 350 2-1/2 Coil Kit. Ford F-250, F350 2011-2015. Part#: 013255 Part#: 013255 Ford F-250 / 350 2-1/2 Coil Kit Ford F-250, F350 2011-2015 Rev.040815 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web/live chat: www.bds-suspension.com. E-mail: tech@bds-suspension.com

More information

TITAN Fuel Tanks. Extended Capacity Replacement Tank for Diesel Chevrolet / GMC Trucks

TITAN Fuel Tanks. Extended Capacity Replacement Tank for Diesel Chevrolet / GMC Trucks Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended Capacity Replacement Tank

More information

CDS TROUBLESHOOTING SECTION I. VACUUM. 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg)

CDS TROUBLESHOOTING SECTION I. VACUUM. 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg) CDS TROUBLESHOOTING SECTION I. VACUUM 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg) 1.1. Clogged hoses or wand tube. Disconnect hoses and carefully check for an obstruction. 1.2. Excessive

More information

94-95 Mustang GT 5.0 HO Smog System Removal

94-95 Mustang GT 5.0 HO Smog System Removal 94-95 Mustang GT 5.0 HO Smog System Removal This is a How To article to remove the smog system from a 94-95 SN95 5.0 HO Mustang GT and installing a delete pulley kit in its place. I tried to include everything

More information

TRANS-05, Torque Tube Removal, Rebuilding, and Installation

TRANS-05, Torque Tube Removal, Rebuilding, and Installation TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket

More information

ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH

ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH The original design of the 03 Alpine Coaches (and perhaps other years as well) did not include any kind of engine fan engage mechanism

More information

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations

More information

Fitting Instruction: Daytona 675 Street Triple from VIN 411984, Street Triple R from VIN 411984 A9930222

Fitting Instruction: Daytona 675 Street Triple from VIN 411984, Street Triple R from VIN 411984 A9930222 English Fitting Instruction: Daytona 675 Street Triple from VIN 98, Street Triple R from VIN 98 A990 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's

More information

Section 6 Brake Drum Failure Analysis. Brake Drum Wear Conditions. What is Normal Wear? What is Deep or Excessive Wear? WARNING. Deep, Uniform Wear

Section 6 Brake Drum Failure Analysis. Brake Drum Wear Conditions. What is Normal Wear? What is Deep or Excessive Wear? WARNING. Deep, Uniform Wear Section Brake Drum 6 Failure Analysis WARNING To prevent serious eye injury, always wear safe eye protection when you perform vehicle maintenance or service. Figure 6.1 ASBESTOS AND NON-ASBESTOS FIBERS

More information

DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH)

DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH) Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH) DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX

More information

Fuel Injection Pump, Rotary (005-014)

Fuel Injection Pump, Rotary (005-014) Fuel Injection Pump, Rotary View Related Topic Page 1 of 30 Fuel Injection Pump, Rotary (005-014) Table of Contents Summary General Information Preparatory Steps Remove Front Gear Train Rear Gear Train

More information

FOR ANY QUESTIONS, PLEASE CALL US @ 727.347.9915 M-F 8:00a.m.-8:00p.m. EST. REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915

FOR ANY QUESTIONS, PLEASE CALL US @ 727.347.9915 M-F 8:00a.m.-8:00p.m. EST. REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915 REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915 REAR BRAKES Before getting started, remove all stock braking components. Pre-assembly of parts: Clean the bolts and the threads in the hat with acetone.

More information

Assembly overview - fuel tank

Assembly overview - fuel tank Assembly overview - fuel tank vw-wi://rl/n.en-gb.k02589829.wi::33090894.xml?xsl=3 Page 1 of 2 Assembly overview - fuel tank 1 - Fuel tank 2 - Sleeve When removing, support using engine and gearbox jack

More information