Housings. Housings for inserts. Housings for inserts. Housings for inserts. Housings for inserts. Housings for inserts. Housings for inserts

Transcription

1 Housings Page A 3, A 4, A 5, D, D 8, plastic 91 A 3, A 4, A 5, D 8, zinc die casting 92 Housing size 1 A and D Housing size 2 A 16 and D 99-0 Housing size 3 A 32 and D Housing size 4 B 6, BB, DD 24, MOB 6-9 Housing size 5 B, BB, DD 42, MOB Housing size 6 B 16, BB 32, BA 6, D 40, DD 2, MOB Housing size B 24, BB 46, D 64, DD 8, MOB Housing size 8 B 32, BB 64, BA 12, D 80, DD 144, 2 x MOB Housing size 9 B 48, BB 92, BV 20, BV 26, BV 32, D 128, DD 216, 2 x MOB Housing size 89

2 Specifications of size 1 housings and short overview of installation possibilities for series A 3, A 4, A 5, D and D 8 inserts Plastic housings Material: Glass-fibre reinforced polyamide Locking levers: Polyamide Flame class rating acc. to UL 94: V 0 Housing seal: NBR Temperature range: - 40 C up to + 1 C (depending on cable gland) Protection degree acc. to DIN EN : IP 65 (in locked condition) Metal housings Material: Zinc die casting Surface: Powder coated Locking levers: Zinc-plated steel Housing seal: NBR Temperature range: - 40 C up to + 1 C (depending on cable gland) Protection degree IP 65 (in locked condition) acc. to DIN EN : D - inserts are only suitable for plastic housings! The housings shown on the following pages can be equipped with the inserts listed below: A 3 Female insert, screw terminal, Screw terminal inserts Male insert, screw terminal, Crimp contact carriers 4 p. 14 A 4 Part no Female insert, screw terminal, Part no Male insert, screw terminal, 4 p. 15 A 5 Part no Part no Female insert Male insert 4 p. 15 D Part no Crimp contact carrier for sleeve contacts, Part no Crimp contact carriers for pin contacts, 4 p. 40 Part no Part no D 8 - only for plastic housings - - only for plastic housings - Crimp contact carrier for sleeve contacts, Crimp contact carriers for pin contacts, 4 p. 41 Part no Part no The page reference at the left of the table guides you to the detailed overview of inserts. Contacts for crimp contact carriers of series... A 5: see page 15 D : see page 40 D 8: see page 41 90

3 Description Previous New M Housings for series A 3, A 4, A 5, D, D 8 g Housings: plastic Wall mount housing, height.5 mm with ed hole -/ OV T T MS T MV with ed hole -/00 61 OV T T MS T MV Housings open at flange Panel housings, height 24 mm, straight Panel cut out Panel housings, height.5 mm, angled Panel cut out Coupler hoods, height 60.5 mm, top cable entry 00 6 OV 00 6 T 00 6 MS T 00 6 MV OV T MS T MV 2 2 for single locking system, side cable entry OV T MS T MV OV T MS T MV Hoods, height 48 mm Hoods, height 5 mm for single locking system, top cable entry 00 6 OV 00 6 T 00 6 MS T 00 6 MV OV T MS T MV Protective covers: plastic Protective covers with retaining cord for housings, for housings with: female insert male insert MD retaining cord

4 Description Previous New Housings for series A 3, A 4, A 5, D 8 g Housings: zinc die casting Wall mount housing, height.5 mm with open bottom with ed hole - / OV T T MS T MV with closed bottom with ed hole - / OV T T MS T MV Panel housings, height 24 mm, straight Panel housing, height 24 mm, straight only for female insert, with hinged cover only for male insert, with hinged cover, without gasket OD Panel housings, height.5 mm, angled Coupler hoods, height 60.5 mm, top cable entry OV T MS T MV Hoods, height 48 mm for single locking system, side cable entry OV T MS T MV Hoods, height 5 mm for single locking system, top cable entry OV T MS T MV

5 A 3 Connectors with Insulation Displacement Connection The convenience of insulation can now be utilized with a classic square connector a 4 pole (3 + PE) industrial plug connector, series A. Male and female versions are available in hood and coupler hoods made of plastic. Assembly Slide the sleeve nut of the insulation onto the stripped conductor. Screw the sleeve nut onto the plug connector and the round conductor connection is ready. Thanks to insulation displacement connection it now only takes a few seconds to connect the 4-pole round conductor: Only the sleeve nut has to be slid onto the conductor since splicing ring, seal and strain relief are included in the sleeve nut. Lead the cores into the marked core entries and cut off the projecting core ends fl ush, i.e. so that there is no overhang. If you need to undo the connection, then just unscrew the sleeve nut. IDC technique is tested on the basis of: EN : Solder-free and inaccessible IDC terminal blocks EN : Entries for cables and conductors DIN EN : Equipment for IDC terminal points DIN VDE 062: Connectors and plug-in socket devices Series A 3 connectors with insulation Description Part no. M g A 3 connectors with insulation Hoods with female insert Height 66 mm for single locking system Hoods with male insert Height 66 mm for single locking system Coupler hood with female insert Height 63 mm Coupler hood with male insert Height 63 mm General specifications of A 3 connectors with insulation see page 14 93