EqualLogic DCB Configuration Best Practices

Transcription

1 EqualLogic DCB Configuration Best Practices A Dell EqualLogic Best Practices Technical White Paper Dell Storage Engineering May 2014

2 Revisions Date February 2013 February 2013 May 2013 May 2014 Description Initial publication Changed PC81xx configuration steps to external SGC link Added Force10 S4820T information Updated links to new Switch Configuration Guides 2014 Dell Inc. All Rights Reserved. Dell, the Dell logo, and other Dell names and marks are trademarks of Dell Inc. in the US and worldwide. All other trademarks mentioned herein are the property of their respective owners. 2 BP1058 EqualLogic DCB Configuration Best Practices

3 Table of Contents 1 Introduction Objective Audience DCB configuration guidelines DCB requirements summary Configuration process overview Enabling DCB and configuring the VLAN Switch configuration Disabling DCB on the SAN DCB configuration verification Priority Group, ETS, and PFC verification Invalid DCB configuration detection Switch specific configuration steps Configuration for switches with DCB support Force10 S Force10 S4820T Force10 MXL PowerConnect 81XX Series Cisco Nexus 5548UP Brocade B Configuration for switches that do not support DCB for EqualLogic PowerConnect 8024, 8024F, and M Cisco Nexus 5010/5020 and Nexus A EqualLogic command line reference for DCB configuration verification B Broadcom 57810S configuration and verification B.1 Broadcom 57810S DCBX willing mode verification B.2 Broadcom 57810S iscsi VLAN configuration B.3 Broadcom 57810S DCB configuration verification BP1058 EqualLogic DCB Configuration Best Practices

4 1 Introduction Data Center Bridging (DCB) is a networking standard that first appeared on Fibre Channel over Ethernet (FCoE) SANs as a method to ensure lossless delivery of Fibre Channel (FC) traffic from Ethernet hosts to FC storage targets. Over recent years, this technology has been extended to deliver similar benefits for iscsi storage solutions and continues to gain acceptance with storage networking device manufacturers and customers. Beginning with Dell EqualLogic Firmware release 5.1 in 2010, Dell introduced DCB for iscsi on all 10 GbE PS Series products. Given that all network elements in a DCB-enabled iscsi SAN need to support DCB, Dell offers PowerEdge converged network adapters (CNAs) and Ethernet switches in the PowerConnect and Force10 product line that support DCB for iscsi. A complete listing of all Ethernet switches and CNAs validated for DCB compliance with EqualLogic can be found in the EqualLogic Compatibility Matrix at Objective The purpose of this document is to provide an overview of the DCB requirements for EqualLogic and to assist with identifying and resolving basic DCB configuration issues in the EqualLogic SAN. This information may be used to ensure that DCB is properly enabled across all devices in the SAN or to ensure that DCB is effectively disabled if it is not required. Note: For an in-depth tutorial of DCB, refer to the Dell white paper, Data Center Bridging: Standards, Behavioral Requirements, and Configuration Guidelines with Dell EqualLogic iscsi SANs at Audience This document is primarily targeted at storage and networking administrators who are responsible for the design, deployment, and maintenance of Dell EqualLogic SANs and related system components. It is assumed that the reader has operational and administrative knowledge of EqualLogic storage, iscsi SAN network design, and related EqualLogic networking best practices. For a comprehensive listing of EqualLogic networking best practices, please refer to the EqualLogic Configuration Guide at 4 BP1058 EqualLogic DCB Configuration Best Practices

5 2 DCB configuration guidelines 2.1 DCB requirements summary It is required that all devices in the EqualLogic SAN support DCB for iscsi when this functionality is enabled. If any device in the SAN does not support DCB, then DCB must be disabled at the switches for the entire SAN. Once all devices in the SAN are DCB compliant, then DCB can be re-enabled. Devices that are designated as DCB Supported in the EqualLogic Compatibility Matrix have been fully validated by Dell to ensure compatibility for EqualLogic SANs. In deployments that contain devices not listed in the EqualLogic Compatibility Matrix, ensure that all Ethernet switches and CNAs in the SAN adhere to the following DCB standards: Support for DCB versions 1.01 (also known as Baseline DCBx or CEE DCBx) or IEEE DCB. Data Center Bridging Exchange (DCBX) DCB protocol that performs discovery, configuration, and mismatch resolution using Link Layer Discovery Protocol (LLDP). iscsi application priority Support for the iscsi protocol in the application priority DCBX Type Length Value (TLV). Advertises the priority value (IEEE 802.1p CoS, PCP field in VLAN tag) for iscsi protocol. End devices identify and tag Ethernet frames containing iscsi data with this priority value. Enhanced Transmission Selection (ETS) Provides minimum, guaranteed bandwidth allocation per traffic class/priority group during congestion and permits additional bandwidth allocation during non-congestion. Priority-based Flow Control (PFC) - Independent traffic priority pausing and enablement of lossless packet buffers/queuing for iscsi. 2.2 Configuration process overview Important: With all network configuration changes, there is the possibility of service interruptions. Network changes required to properly configure DCB for EqualLogic will result in a temporary loss of connectivity. Therefore, Dell strongly recommends that all network environment changes are performed during a planned maintenance window. This section provides general steps to configure DCB for EqualLogic and Section 3 contains detailed steps for specific Dell and other switch models. These steps apply to both new deployments and those deployments that have DCB improperly configured. It is important to verify that all components in the SAN are listed in the EqualLogic Compatibility Matrix as DCB Supported or that the components support all EqualLogic requirements for DCB. If multiple switches are in the path between iscsi Hosts and EqualLogic arrays, then all configuration steps below must be applied to these switches. For SAN deployments with two or more switch hops, please refer to Data Center Bridging: Standards, Behavioral Requirements, and Configuration Guidelines with Dell EqualLogic iscsi SANs for additional configuration guidance and considerations at: 5 BP1058 EqualLogic DCB Configuration Best Practices

6 When configuring DCB on a new array member, ensure the switch is setup properly first. The CLI setup wizard or the Remote Setup Wizard will detect the switch is DCB capable and prompt for the required configuration information, including the VLAN ID, during setup. To configure DCB on an existing EqualLogic array member: 1. Disable DCB on the switch, if it is enabled. 2. Verify that all CNAs are enabled and configured in DCB willing mode. 3. Verify that the EqualLogic array has DCB enabled (Note: This is enabled by default and should never be disabled). 4. Enter a VLAN ID from in Group Manager. With firmware v7 and later, the VLAN ID will default to 2 when DCB is detected on the switch. 5. On the switch, create a VLAN in trunk mode for all switch ports connected to arrays and iscsi hosts with the same VLAN ID configured on the array. 6. Configure all CNAs with same VLAN ID configured on the array. 7. On the switch, configure Priority Groups/ETS, PFC, and iscsi application priority on all ports connected to EqualLogic arrays and iscsi host CNAs. The same should be configured for any switch interconnects (LAGs, VLTi, vpc, and others) 8. Enable DCB on the switch. 9. Verify all DCB configuration and operational parameters on array ports via Group Manager. 10. Verify DCB operational parameters on CNAs using the respective management application. Steps 1, 3, 4, 7, 8, and 9 are outlined in the following section. Appendix B provides additional guidance for steps 2, 6, and 10 using the Broadcom 57810S CNA. 2.3 Enabling DCB and configuring the VLAN The DCB VLAN setting can be found in the Group Manager Summary page as seen below. For firmware versions prior to 7.x, the Enable DCB checkbox should always be checked. With firmware version 7.x and later, the checkbox is no longer displayed and DCB is always enabled and in willing mode. 6 BP1058 EqualLogic DCB Configuration Best Practices

7 Figure 1 DCB VLAN setting from Group Manager v7 Important: At no point should DCB be disabled on the array. This is important for several reasons: DCB is enabled on 10 Gb capable arrays by default and in willing mode. It can only be disabled via CLI and should only be done if instructed by Dell support. Disabling DCB on the array does not ensure that DCB is fully disabled in the SAN and flow control may not be enabled between the switch ports, hosts, and arrays. When DCB is enabled, the arrays receive DCB configuration information from the switch and will continue to provide real-time DCB status which can be used to verify the configuration. If the attached switch ports are not DCB enabled, then the array ports will operate in standard (802.3x) flow control mode. Next, a valid VLAN ID must be entered. The range of recommended values is However, verify that the VLAN ID choice does not conflict with any default or reserved IDs for your specific switch make and model. With firmware v7 and later, the VLAN ID will default to 2 when DCB is detected on the switch. Important: When DCB is enabled on the switch, it is necessary to configure a non-default VLAN on the array, switch, and all host ports that are part of the EqualLogic SAN. VLAN IDs 0 and 1 should not be used as these may be the default or reserved VLAN for some switches, and as such, may forward frames untagged (with no VLAN tagging). VLAN tagging is required to fully support DCB. 2.4 Switch configuration For switch configuration steps, refer to Section 3 and find your specific switch model. If the specific switch is not listed, consult with your switch vendor to confirm the DCB support requirements for EqualLogic and obtain instructions for configuring (or disabling) DCB on the switch as needed. 7 BP1058 EqualLogic DCB Configuration Best Practices

8 2.5 Disabling DCB on the SAN When DCB functionality is not required for the SAN deployment, DCB must be disabled on all switches in the SAN. Once DCB is disabled on the SAN, the attached EqualLogic arrays and CNAs will no longer receive DCBx messages from the attached switches, effectively disabling DCB functionality on the SAN completely. Configuration steps for disabling DCB can also be found in Section 3. Important: If DCB is disabled on the switch, ensure that 802.3x flow control is enabled on all switch ports attached to the EqualLogic arrays and iscsi hosts. EqualLogic best practices recommend a minimum of RX flow control on the switch ports. Also it is assumed that the switches are dedicated for SAN traffic alone when DCB is disabled. Important: If DCB is disabled on a switch, then all DCB functionality will be disabled, including support for other protocols such as FCoE. Mixing of FCoE and iscsi on the same converged fabric is not recommended and not supported by Dell. Note: VLAN tagging is only supported when DCB mode is fully enabled and configured. If DCB is disabled on the switch, switch ports must be configured as untagged or as access ports (or left in the native VLAN). 2.6 DCB configuration verification The following sections show how to verify the DCB configuration of a switch via the EqualLogic Group Manager. Equivalent methods for verifying the configuration via the command line interface (CLI) are provided in Appendix A Priority Group, ETS, and PFC verification To determine what configuration steps in Section 2 are needed to properly configure switches and correct the error condition, verify the following information in Group Manager. 1. In Group Manager, click a member array and go to the Network tab. 2. Right-click on each 10 Gb interface (for example eth0) and click DCB Details to display the dialog box shown below. 8 BP1058 EqualLogic DCB Configuration Best Practices

9 3. From these details, verify the following: a. Column 1: For the iscsi Traffic Class Group (Group 1, in this example), only iscsi is present (no other traffic classes should appear, such as FCoE). b. Column 2: ETS % from 1 to 100% (recommend 50% as an initial setting). c. Column 3: Priority level for iscsi is 4 (recommended). d. Column 4: Lossless state for iscsi equals PFC ON for priority Repeat this verification for all 10 Gb array interfaces in the group Invalid DCB configuration detection A new capability released with version 6.0 of the EqualLogic firmware automatically detects if there is an invalid configuration state on the Ethernet switch attached to the EqualLogic array due to the following conditions: PFC is configured (PFC TLV received) iscsi is using a priority group which is not PFC enabled (lossless) This state will result in a warning message that will be displayed at the bottom of the EqualLogic Group Manager interface as shown in Figure 3. Figure 2 Invalid DCB configuration detection warning message in Group Manager v7 If a switch does not support the iscsi TLV, it may not be possible to properly classify the iscsi traffic and assign it to a priority group and enable DCB Priority-based Flow Control. In this case, the array will place all iscsi frames in default priority 0. Typically, priority 0 will not have PFC enabled on the switch, which means that iscsi traffic would be treated with the same priority as all other traffic or in some cases, with a 9 BP1058 EqualLogic DCB Configuration Best Practices

10 lower priority. It is also possible that even when the iscsi TLV is supported by the switch, the iscsi priority may not have PFC enabled for that priority. Upon detection of either of these conditions, the array will issue a warning message that Ethernet flow control has been disabled on one or more interfaces. Operation with no flow control may cause performance degradation and service interruptions. Refer to subsequent sections in this document for information on corrective actions. Figure 3 Invalid DCB configuration detection warning message in Group Manager v6 In addition to this warning message, a more detailed message will appear in the event log and CLI as shown in these examples: Firmware Versions up to 6.0.3: Interface eth0 has negotiated DCB Priority-based Flow Control with the switch. However, the switch did not configure iscsi traffic for a lossless priority. No Ethernet flow control is enabled for iscsi on this interface. Firmware versions and higher: Interface eth0 has detected an invalid switch configuration. All iscsi initiators and targets connected to this switch will have no flow control for iscsi until this is corrected. Firmware version and higher: An invalid switch configuration has been detected. This issue must be corrected in the network infrastructure. Refer to the document located at: 10 BP1058 EqualLogic DCB Configuration Best Practices

11 3 Switch specific configuration steps In this section, switch-specific commands are provided to correctly configure DCB for the EqualLogic SAN or disable it completely if DCB is not required. This is not a comprehensive set of configuration commands for EqualLogic deployments; it is only intended to address the DCB configuration aspect of switches within the EqualLogic SAN. 3.1 Configuration for switches with DCB support The following switches feature DCB with the requirements necessary to fully support EqualLogic storage systems. These switches can be configured for DCB mode or as a dedicated SAN switch with standard link-level (802.3x) flow control Force10 S4810 Refer to the Dell Force10 S4810 Switch Configuration Guide for instructions related to DCB or non-dcb configuration at Force10 S4820T Refer to the Dell Force10 S4820TSwitch Configuration Guide for instructions related to DCB or non-dcb configuration at Force10 MXL Refer to the Dell Force10 MXL 10/40 GbE Blade Switch Configuration Guide for instructions related to DCB or non-dcb configuration at PowerConnect 81XX Series Refer to the Dell PowerConnect 8100Series Switch Configuration Guide for instructions related to DCB or non-dcb configuration at Cisco Nexus 5548UP Refer to the Cisco Nexus 5548-UP Switch Configuration Guide for instructions related to DCB or non- DCB configuration at 11 BP1058 EqualLogic DCB Configuration Best Practices

12 3.1.6 Brocade B8000 Refer to the Brocade B8000 Switch Configuration Guide for instructions related to DCB or non-dcb configuration at Configuration for switches that do not support DCB for EqualLogic The following switches do not fully support DCB requirements for EqualLogic, so DCB must be disabled on these SAN switches. Important: If DCB is disabled on a switch, then all DCB functionality will be disabled, including support for other protocols such as FCoE. Mixing of FCoE and iscsi on the same converged fabric is not recommended and not supported by Dell PowerConnect 8024, 8024F, and M8024 The first step in configuring this line of switches is to first verify the firmware version installed is or higher. Note: If an earlier firmware version is installed, it will not be possible to fully disable DCB on the switch and correct the invalid flow control condition on the arrays and hosts. Upgrade instructions can be found under the corresponding product firmware download pages at To disable DCB, refer to the following guide: Cisco Nexus 5010/5020 and Nexus 7000 The Cisco Nexus 5010/5020 and Nexus 7000 family enables DCB by default, but it does not support the iscsi TLV. Furthermore, Cisco does not provide a method for fully disabling DCB on the switch. Note: All firmware versions do not support DCB with iscsi TLV. DCB support on these switches is for FCoE only. DCB functionality can be disabled on the Nexus 5000 and 7000 switches by disabling LLDP on all ports that connect to EqualLogic array controller ports. This essentially prevents the transmission of DCBX advertisements to the storage system. 12 BP1058 EqualLogic DCB Configuration Best Practices

13 A EqualLogic command line reference for DCB configuration verification From the CLI (GroupAdmin login), the following commands can be executed to obtain the same information that is presented in the Group Manager GUI: show grpparams (Display Global DCB and VLAN status): PG1> show grpparams Group Information Name: PG1 Group-Ipaddress: Group-Mgmt-Gateway: Def-Snap-Reserve: 100% Def-Snap-Warn: 10% Def-Snap-Depletion: delete-oldest Def-Thin-Growth-Warn: 60% Def-Thin-Growth-Max: 100% DateAndTime: Fri Nov 9 13:32: TimeZone: America/New_York Description: Def-Iscsi-Prefix: Def-Iscsi-Alias: yes iqn com.equallogic Info-Messages: enabled Webaccess: enabled Webaccess-noencrypt: enabled Cliaccess-SSH: enabled Cliaccess-Telnet: enabled -Notify: disabled Syslog-Notify: disabled isns-server-list: -List: NtpServers: Smtp-Server-List: DNS-Server-List: DNS-Suffix-List: Syslog-Server-List: Target-Auth-UserName: Target-Auth-Password: Zphr8HHZj2PJX22H BbH822Bx2xXpBRJZ -From: Location: default Conn-Balancing: enabled Discovery-Use-Chap: disabled -Contact: Perf-balancing: enabled Disallow-Downgrades: yes Management-Ipaddress: SSH-V1-Protocol: enabled Standby-Button: disabled FTP-service: enabled Def-DCB-VLAN-Id: 100 DCB: enabled Crypto-Legacy-Protocols: enabled Thermal-Shutdown: enabled Session-Idle-Timeout: 0 Volume-Recovery: enabled Session-Banner-Enable: disabled Session-Idle-Timeout-Enable: disabled Def-Snapshot-Borrow: disabled member select <array-name> eth show (Display DCB ON/OFF): The example below is from an EqualLogic PS6110, so eth0 is the iscsi port and eth1 is the management port which shows the DCB as off for the management port. PG1> member select P1 eth show Name iftype ifspeed Mtu Ipaddress Status Errors DCB eth0 ethernetcsmacd 10 Gbps up 0 on eth1 ethernetcsmacd 100 Mbps up 0 off 13 BP1058 EqualLogic DCB Configuration Best Practices

14 member select <array-name> eth select 0 dcb show (Display DCB details): PG1> member select P1 eth select 0 dcb show Eth DCB Information Name: eth0 DCB: on Lossless-Priorities: on Traffic-Classes: on Congestion Notification: off iscsi-priority: 4 member select <array-name> eth select 0 dcb lossless-priority show (Display Lossless Priority configuration): PG1> member select P1 eth select 0 dcb lossless-priority show Priority Status 0 off 1 off 2 off 3 off 4 on 5 off 6 off 7 off member select <array-name> eth select 0 dcb traffic-class show (Display Traffic Classes): PG1> member select P1 eth select 0 dcb traffic-class show Traffic Bandwidth Priorities Class % 50% 4 0,1,2,3,5,6,7 14 BP1058 EqualLogic DCB Configuration Best Practices

15 B Broadcom 57810S configuration and verification B.1 Broadcom 57810S DCBX willing mode verification Figure 4 below shows a screen shot from the Broadcom Advanced Control Suite (BACS). This is applicable to the Broadcom 57810S Dual-Port 10 GbE SFP+ adapter and the Broadcom 57810S Dual-Port 10 GbE KR Blade Converged Mezzanine Card on Windows Server 2008 R2 SP1. The parameter local machine willing indicates the willing mode state and is enabled by default. Figure 4 Initiator willing mode configuration In this figure, the adapter is configured with willing mode enabled by default. Also the local DCBX settings are shown in the default configuration. These settings include the priority and PFC values for FCoE and iscsi. This also includes the priority groups with their bandwidth allocation and priority mapping. Once the adapter port establishes an operational link with a peer switch port and receives the switch DCBX settings, it will use those settings for DCB operations. The local settings will not be operational at that point. The default local DCBX setting can be changed by overriding them. 15 BP1058 EqualLogic DCB Configuration Best Practices

16 B.2 Broadcom 57810S iscsi VLAN configuration The figure below illustrates the VLAN configuration for iscsi traffic on the adapter port. Figure 5 Initiator VLAN ID configuration B.3 Broadcom 57810S DCB configuration verification The image below is the screen shot from the Broadcom Advanced Control Suite. This is applicable to the Broadcom 57810S Dual-Port 10 GbE SFP+ adapter and the Broadcom 57810S Dual-Port 10 GbE KR Blade Converged Mezzanine Card on Windows Server 2008 R2 SP1. The DCB parameters shown are the values advertised by the switch peer and accepted by the NIC port. It also indicates the DCB operational state for each feature. Figure 6 DCBX operation state and configuration verification 16 BP1058 EqualLogic DCB Configuration Best Practices

17 The local and remote DCBX settings are displayed in the DCBX Advanced section of the BACS, see Figure 7. Figure 7 Advanced DCB operation state and configuration verification 17 BP1058 EqualLogic DCB Configuration Best Practices