TO INDEX WIPER AND WASHER REAR WIPER MOTOR ASSEMBLY WINDSHIELD WIPER SWITCH ASSEMBLY WINDSHIELD WASHER JAR ASSEMBLY

Transcription

1 TO INDEX BODY AND ELECTRICAL WIPER AND WASHER WIPER AND WASHER SYSTEM BASIC INSPECTION LOCATION PROBLEM SYMPTOMS TABLE WINDSHIELD WIPER MOTOR ASSEMBLY COMPONENTS REMOVAL INSTALLATION ON-VEHICLE INSPECTION INSPECTION WIPER RUBBER LH COMPONENTS REMOVAL INSTALLATION REAR WIPER MOTOR ASSEMBLY COMPONENTS REMOVAL INSTALLATION ON-VEHICLE INSPECTION INSPECTION REAR WIPER RUBBER COMPONENTS REMOVAL INSTALLATION WINDSHIELD WIPER SWITCH ASSEMBLY COMPONENTS REMOVAL INSTALLATION INSPECTION WASHER NOZZLE INSPECTION WINDSHIELD WASHER JAR ASSEMBLY COMPONENTS REMOVAL INSTALLATION WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY ON-VEHICLE INSPECTION REAR WASHER NOZZLE INSPECTION

2 1 WIPER AND WASHER - WIPER AND WASHER SYSTEM BODY AND ELECTRICAL WASHER WIPER AND WASHER SYSTEM BASIC INSPECTION 1. CHECK WIPER AND WASHER SYSTEM (1) CHECK OPERATION OF WIPER AND WASHER (a)with the ignition switch (IG) ON, check the operation of the wipers. Standard: LO position:: Sets the speed to low. HI position:: Sets the speed to high. INT position:: Sets the speed to intermittent. MIST position:: Wipes 1 time and then stops. (b)check the wiping status when the wipers are operating. Standard:: Spray direction and height are good. (c)check the direction and height of the wiper fluid when it is sprayed. Standard:: Spray direction and height are good. (d)visually check the amount of washer fluid in the washer tank. Standard:: There is sufficient washer fluid in the washer tank.

3 WIPER AND WASHER - WIPER AND WASHER SYSTEM 2 LOCATION REAR WASHER NOZZLE REAR WIPER ARM ASSEMBLY REAR WIPER MOTOR ASSEMBLY WINDSHIELD WIPER SWITCH ASSEMBLY FRONT WIPER ARM RH WINDSHIELD WIPER LINK ASSEMBLY WASHER NOZZLE FRONT WIPER ARM LH WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY INSTRUMENT PANEL J/B ASSEMBLY -IG FUSE -ACC FUSE -WIP WSHR FUSE WASHER NOZZLE WINDSHIELD WIPER MOTOR ASSEMBLY E128156J02 PROBLEM SYMPTOMS TABLE FRONT WIPER AND WASHER Symptom Suspected Area See Page Both the wipers and the washer do not operate WIP WSHR fuse - Windshield wiper switch assembly -23 Wire harness -

4 3 WIPER AND WASHER - WIPER AND WASHER SYSTEM Symptom Suspected Area See Page Washer does not operate when in either the LO or HI setting Washer does not operate on the INT setting Washer motor does not operate Washer fluid does not spray With the wiper switch ON, the wipers do not operate when the washer is operated When the wiper switch is turned OFF, the wiper blades do not return to the stopped position, or the stopped position is incorrect WIP WSHR fuse - Windshield wiper switch assembly -23 Windshield wiper motor assembly -11 Wire harness - WIP WSHR fuse - Windshield wiper switch assembly -23 Windshield wiper motor assembly -11 Wire harness - WIP WSHR fuse - Windshield wiper switch assembly (washer switch) -23 Windshield washer motor and pump assembly (front spray -28 position) Wire harness - Washer hose - Washer nozzle - WIP WSHR fuse - Windshield wiper switch assembly (washer switch) -23 Windshield wiper motor assembly -11 Windshield wiper motor assembly (automatic stop position) -11 Vehicle wire harness and connector - REAR WIPER AND WASHER Symptom Suspected Area See Page Both the rear wiper and the rear washer do not operate Rear wiper does not operate Rear washer motor does not operate Rear washer does not spray When the rear wiper is OFF, the rear wiper blade does not return to the stopped position. WIP WSHR fuse - Windshield wiper switch assembly -23 Wire harness - WIP WSHR fuse - Windshield wiper switch assembly -23 Rear wiper motor assembly -17 Wire harness - WIP WSHR fuse - Windshield wiper switch assembly (rear washer switch) -23 Windshield washer motor and pump assembly (rear spray -28 position) Wire harness - Washer hose - Washer nozzle - Rear wiper motor assembly -17 Wire harness -

5 WIPER AND WASHER - WINDSHIELD WIPER MOTOR ASSEMBLY WINDSHIELD WIPER MOTOR ASSEMBLY BODY WIPER AND ELECTRICAL WASHER COMPONENTS 4 FRONT WIPER ARM HEAD CAP FRONT WIPER ARM AND BLADE ASSEMBLY LH FRONT WIPER ARM HEAD CAP FRONT WIPER ARM AND BLADE ASSEMBLY RH COWL TOP VENTILATOR LOUVER COWL TOP VENTILATOR LOUVER BONNET (HOOD) TO COWL TOP SEAL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY WINDSHIELD WIPER MOTOR ASSEMBLY 3 WINDSHIELD WIPER LINK ASSEMBLY TIGHTENING TORQUE [N*m{kgf*cm}] E130099J01

6 5 WIPER AND WASHER - WINDSHIELD WIPER MOTOR ASSEMBLY REMOVAL 1. DISCONNECT NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (a) Remove the front wiper arm nut. Then remove the front wiper arm and blade assembly RH. E REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (a) Remove the front wiper arm nut. Then remove the front wiper arm and blade assembly RH. 4. REMOVE COWL TOP VENTILATOR LOUVER (a) Disengage the 7 clips and remove the cowl top ventilator louver. E Clip E127784J01

7 WIPER AND WASHER - WINDSHIELD WIPER MOTOR ASSEMBLY 6 (b) Detach the 2 clips and 10 claws, and remove the cowl top ventilator louver as shown in the illustration. Clip Claw E127785J01 5. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (FOR VEHICLES WITHOUT COLD WEATHER SPECIFICATIONS) (a) Remove the 3 bolts. (b) Remove the clamp and connector. Then remove the windshield wiper motor and link assembly. E REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (FOR VEHICLES WITH COLD WEATHER SPECIFICATIONS) (a) Disconnect the connector and clamp. E (b) (c) Remove the 3 bolts. Remove the clamp and connector. Then remove the windshield wiper motor and link assembly. E129775

8 7 WIPER AND WASHER - WINDSHIELD WIPER MOTOR ASSEMBLY 7. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY (a) Using a screwdriver covered with protective tape, remove the arm of the windshield wiper link assembly from the crank arm pivot of the windshield wiper motor assembly, as shown in the illustration. Protective Tape E107892J01 (b) Remove the 3 bolts. Then remove the windshield wiper motor assembly. HINT: If the windshield wiper motor assembly cannot easily be removed from the windshield wiper link assembly, it can be removed by turning the crank arm until the windshield wiper motor assembly is in a position where it can be detached. INSTALLATION E INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY (a) Install the windshield wiper motor assembly to the windshield wiper link assembly with the 3 bolts. Torque: 5.4 N*m (55 kgf*cm) (b) Coat the pivoting part of the crank arm of the windshield wiper motor assembly with Denso No. 50 grease. E (c) Connect the arm of the windshield wiper link assembly to the pivoting part of the crank arm of the windshield wiper motor assembly. 9. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (FOR VEHICLES WITHOUT COLD WEATHER SPECIFICATIONS) (a) Connect the connector. (b) Engage the rubber pin. E107894

9 WIPER AND WASHER - WINDSHIELD WIPER MOTOR ASSEMBLY 8 (c) Install the windshield wiper motor and link assembly with the 3 bolts. Torque: 5.5 N*m (56 kgf*cm) (d) Connect the connector. 10. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (FOR VEHICLES WITH FOR COLD WEATHER SPECIFICATIONS) (a) Connect the connector to the wiper motor assembly. E129775J01 (b) Engage the rubber pin. (c) Install the windshield wiper motor and link assembly with the 3 bolts. Torque: 5.5 N*m (56 kgf*cm) E (d) Connect the connector and clamp. 11. INSTALL COWL TOP VENTILATOR LOUVER (a) Attach the 10 claws. E132263J01 Clip Claw E127785J01 (b) Engage the 5 claws and the 2 clips, and install the cowl top ventilator louver. 12. CONNECT NEGATIVE BATTERY TERMINAL

10 9 Wiper Arm Serrations Wire Brush WIPER AND WASHER - WINDSHIELD WIPER MOTOR ASSEMBLY 13. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (a) Stop the windshield wiper motor assembly at the automatic stop position. (b) Using a round file or equivalent, clean the wiper arm serration. (when reassembling) (c) Using a wire brush, clean the wiper pivot serration part. (d) Install the front wiper arm and blade assembly RH with the front wiper arm nut, so that it comes to the position shown in the illustration. Wiper Pivot Serrations E053010J E129774J01 Torque: 22 N*m (224 kgf*cm) HINT: While holding down the wiper arm hinge with your hand, tighten the front wiper arm nut.

11 WIPER AND WASHER - WINDSHIELD WIPER MOTOR ASSEMBLY 10 Wiper Arm Serrations 14. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (a) Using a round file or equivalent, clean the wiper arm serration. (when reassembling) (b) Using a wire brush, clean the wiper pivot serration part. (c) Install the front wiper arm and blade assembly LH with the front wiper arm nut, so that it comes to the position shown in the illustration. Wire Brush Wiper Pivot Serrations E053010J E129774J01 (d) Torque: 22 N*m (224 kgf*cm) HINT: While holding down the wiper arm hinge with your hand, tighten the front wiper arm nut. Operate the front wipers while spraying water or washer fluid on the windshield glass. Make sure that the wipers function properly and that there is no interference with the vehicle body. 15. PERFORM INITIALIZATION (See page SS-10.)

12 11 WIPER AND WASHER - WINDSHIELD WIPER MOTOR ASSEMBLY ON-VEHICLE INSPECTION 1. CHECK WINDSHIELD WIPER MOTOR ASSEMBLY (a) CHECK AUTOMATIC STOP POSITION (1) Operate the windshield wiper motor assembly. Then stop the wipers and check the automatic stop position of the wiper arm. Standard: The wiper arm stops at the position shown in the illustration E129774J01 INSPECTION E CHECK WINDSHIELD WIPER MOTOR ASSEMBLY (a) Check LO Operation (1) Connect the positive battery terminal to terminal 1 (+1) of the connector, and the negative battery terminal to terminal 5 (E). Then check that the windshield wiper motor assembly operates at low speed (LO). (b) CHECK HI OPERATION (1) Connect the positive battery terminal to terminal 4 (+2) of the connector, and the negative battery terminal to terminal 5 (E). Then check that the windshield wiper motor assembly operates at high speed (HI).

13 WIPER RUBBER LH BODY AND ELECTRICAL WASHER COMPONENTS WIPER AND WASHER - WIPER RUBBER LH 12 FRONT WIPER BLADE LH FRONT WIPER BACKING PLATE WIPER RUBBER LH FRONT WIPER BACKING PLATE E130802J01 REMOVAL 1. REMOVE FRONT WIPER BLADE LH (a) Remove the front wiper blade LH from the front wiper arm LH, as shown in the illustration. NOTICE: Do not lay the wiper arm down with the wiper blade removed. E127345

14 13 WIPER AND WASHER - WIPER RUBBER LH 2. REMOVE WIPER RUBBER LH (a) Remove the wiper rubber LH, together with the front wiper backing plate, from the front wiper blade LH. (b) Remove the front wiper backing plate from the wiper rubber LH. INSTALLATION E INSTALL WIPER RUBBER LH (a) Install the front wiper backing plate to the wiper rubber LH. NOTICE: Align the recessed part of the backing blade with the protruding part of the wiper rubber LH. Align the R direction of the backing plate with the R direction on the windshield glass. E (b) Install the front wiper blade LH so that the head part (the side that bulges) of wiper rubber LH faces the arm axle side. NOTICE: Firmly push the connectors on the wiper blade into the recessed part of the wiper rubber to attach them completely. 4. INSTALL FRONT WIPER BLADE LH (a) Install front wiper blade LH to front wiper arm LH. E112266

15 WIPER AND WASHER - REAR WIPER MOTOR ASSEMBLY REAR WIPER MOTOR ASSEMBLY BODY WIPER AND ELECTRICAL WASHER COMPONENTS 14 REAR WIPER ARM ASSEMBLY REAR WIPER MOTOR GROMMET REAR WIPER ARM HEAD CAP REAR WIPER MOTOR ASSEMBLY TIGHTENING TORQUE [N*m{kgf*cm}] E130721J01

16 15 WIPER AND WASHER - REAR WIPER MOTOR ASSEMBLY REMOVAL 1. REMOVE REAR WIPER ARM HEAD CAP 2. REMOVE REAR WIPER ARM ASSEMBLY (a) Remove the nut. Then remove the rear wiper arm. 3. REMOVE REAR WIPER MOTOR GROMMET 4. REMOVE BACK DOOR TRIM PANEL ASSEMBLY (See Page ED- 47) 5. REMOVE REAR WIPER MOTOR ASSEMBLY (a) Disconnect the connector. (b) Loosen the 3 bolts. Then remove the rear wiper motor assembly. INSTALLATION 6. INSTALL REAR WIPER MOTOR ASSEMBLY (a) Install the rear wiper motor assembly with the 3 bolts. Torque: 5.5 N*m (56 kgf*cm) (b) Connect the connector. E INSTALL BACK DOOR TRIM PANEL ASSEMBLY (See Page ED- 49) Set Mark 8. INSTALL REAR WIPER MOTOR GROMMET (a) Install the rear wiper motor grommet, with the positioning mark shown in the illustration facing up. Rear Wiper Motor Grommet E102190J01

17 WIPER AND WASHER - REAR WIPER MOTOR ASSEMBLY 16 Wiper Arm Serrations 9. INSTALL REAR WIPER ARM (a) Using a round file or equivalent, clean the serrated part of the rear wiper arm. (when reassembling) (b) Using a wire brush, clean the serrated part of the wiper pivot. (c) Stop the rear wiper motor assembly at the automatic stop position and install the rear wiper arm as shown in the illustration. Wire Brush Wiper Pivot Serrations E060224J01 ±5 E130720J01 (d) Torque: 5.5 N*m (56 kgf*cm) HINT: While holding down the wiper arm hinge with your hand, tighten the front wiper arm nut. Operate the rear wipers while spraying washer fluid or water on the windshield glass. Make sure that the wipers function properly and there is no interference with the vehicle body. 10. INSTALL REAR WIPER ARM HEAD CAP

18 17 WIPER AND WASHER - REAR WIPER MOTOR ASSEMBLY ON-VEHICLE INSPECTION 1. CHECK REAR WIPER MOTOR ASSEMBLY (a) CHECK AUTOMATIC STOP POSITION ±5 E130720J01 (1) Operate the rear wiper motor assembly. Then stop the wipers and check the automatic stop position of the wiper arm. Standard: The position of the rear wiper blade is within 5mm above or below the defogger line. INSPECTION E CHECK REAR WIPER MOTOR ASSEMBLY (a) CHECK OPERATION (1) Connect the positive battery terminal to terminal 1 (+B) of the connector, and the negative battery terminal to terminal 3 (LS). Then check that the rear wiper motor assembly operates. NOTICE: The body ground must be connected. (b) CHECK INTERMITTENT OPERATION (1) Connect the positive battery terminal to terminal 1 (+B) of the connector, and the negative battery terminal to terminal 2 (C1). Then check that the rear wiper motor assembly operates intermittently. NOTICE: The body ground must be connected.

19 REAR WIPER RUBBER BODY WIPER AND ELECTRICAL WASHER COMPONENTS WIPER AND WASHER - REAR WIPER RUBBER 18 Rear Wiper Blade Assembly Rear Wiper Rubber Backing Plate Rear Wiper Rubber Backing Plate Rear Wiper Rubber E107956J01

20 19 WIPER AND WASHER - REAR WIPER RUBBER REMOVAL Claw 1. REMOVE REAR WIPER BLADE (a) Lift up the rear wiper blade. (b) Lift the rear wiper blade to the position shown in the illustration until you hear the sound of the claws snapping out of their engagement. [*1] NOTICE: Be careful not to damage the claws. E036417J01 (c) After completing [*1] above, remove the rear wiper blade from the rear wiper arm by pulling the blade straight away from the wiper arm towards the left side of the vehicle. NOTICE: Do not lay the wiper arm down on the windshield with the wiper blade removed. E036418J01 Stopper (Rear End Tip) Warpage Lightly Push (Squeeze) Hold Up Pull Out E056794J01 2. REMOVE REAR WIPER RUBBER (a) Squeeze the rear wiper rubber out of the stopper at the back end of the rear wiper blade and pull it out as shown in the illustration. NOTICE: Do not pull out the wiper rubber forcibly. Doing so will deform the backing plate or damage the blade claw. HINT: Lightly press around the center of the wiper blade claws until it is easy to lift and pull out the rubber. (b) Remove the backing blade from the rear wiper rubber. INSTALLATION 1. INSTALL REAR WIPER BLADE (a) Install the rear wiper rubber backing plate as shown in the illustration. NOTICE: Make sure that the curve of the backing plate is facing in the proper direction. E036208J01

21 WIPER AND WASHER - REAR WIPER RUBBER 20 Second Claw (b) (c) (d) Insert the rear wiper rubber at the second claw from the front end of the wiper blade and push the rubber through to the rear end of the rear wiper blade. Pass the rear wiper rubber through the rear end side claw and allow it to protrude from the rear end stopper. Pass the rear wiper rubber through the front end claw to install it. Rear End Claw E060705J01 2. INSTALL REAR WIPER RUBBER (a) Engage the claw and install the rear wiper blade to the wiper arm. (b) Confirm that the claws are engaged securely and return the rear wiper arm. E107955

22 21 WIPER AND WASHER - WINDSHIELD WIPER SWITCH ASSEMBLY WINDSHIELD WIPER SWITCH ASSEMBLY BODY WIPER AND ELECTRICAL WASHER COMPONENTS STEERING COLUMN UPPER COVER WINDSHIELD WIPER SWITCH ASSEMBLY STEERING COLUMN LOWER COVER E132255J01 REMOVAL 1. DISCONNECT NEGATIVE BATTERY TERMINAL 2. REMOVE STEERING COLUMN LOWER COVER (a) Turn the steering wheel assembly to the right and remove the screw as shown in the illustration. E127343

23 WIPER AND WASHER - WINDSHIELD WIPER SWITCH ASSEMBLY 22 (b) Turn the steering wheel assembly to the left and remove the screw as shown in the illustration. E (c) (d) Remove the screw. Disengage the 5 claws and remove the steering column lower cover. Claw E127787J02 3. REMOVE STEERING COLUMN COVER UPPER (a) Disengage the claw and remove the steering column upper cover. Clip E127788J01 4. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY (a) Disconnect the connector. (b) Disengage the claws and remove the windshield wiper switch assembly. NOTICE: The claw will be damaged if it is pressed too hard. : Claw E127344J01

24 23 WIPER AND WASHER - WINDSHIELD WIPER SWITCH ASSEMBLY :Claw E128485J01 INSTALLATION 1. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY (a) Insert the windshield wiper switch assembly until the claw engages. (b) Connect the connector. 2. INSTALL STEERING COLUMN UPPER COVER (a) Engage the clip and install the steering column cover upper. 3. INSTALL STEERING COLUMN LOWER COVER (a) Engage the 5 claws and install the steering column lower cover with the screw. 4. CONNECT BATTERY NEGATIVE TERMINAL 5. PERFORM INITIALIZATION (See page SS-10 for details.) INSPECTION 1. CHECK WINDSHIELD WIPER SWITCH ASSEMBLY (a) Check the continuity. (1) Using the tester, check the continuity between each of the connecter terminals. Standard: E Front wiper switch Switch Terminal No. (Terminal Name) Continuity MIST 7 (+1) 8 (WB) Continuity OFF 6 (+S) 7 (+1) Continuity INT 6 (+S) 7 (+1) Continuity LO 7 (+1) 8 (WB) Continuity HIGH 8 (WB) 9 (+2) Continuity Front wiper switch Switch Terminal No. (Terminal Name) Continuity OFF 4 (W) 5 (EW) None ON 4 (W) 5 (EW) Continuity Rear wiper switch Switch Terminal No. (Terminal Name) Continuity WASH 3 (WR) 5 (EW) Continuity OFF (Vehicles with rear intermittent operation) OFF (Vehicles without rear intermittent operation) 3 (WR) 1 (C1R) 2 (+1R) 5 (EW) NEITHER 3 (WR) 5 (EW) NEITHER INT 1 (C1R) 5 (EW) Continuity ON 2 (+1R) 5 (EW) Continuity ON + WASH 3 (WR) 2 (+1R) 5 (EW) Continuity (b) CHECK INTERMITTENT FUNCTION (FRONT WIPERS) (1) Using the tester, connect the 7 (+1) terminal of the connector to the positive (+) terminal of the tester and

25 WIPER AND WASHER - WINDSHIELD WIPER SWITCH ASSEMBLY 24 connect the 5 (EW) terminal to the negative (-) terminal of the tester. (2) Connect the negative battery (-) terminal to the 5 (EW) terminal and the 6 (+S) terminal, and connect the positive battery (+) terminal to the 8 (B) terminal of the connector. (3) Set the front wiper switch to INT. (4) Connect the positive (+) battery terminal to the 6 (+S) terminal of the connector for 5 seconds V 7(+1) 5(EW) Voltage Between Terminals Connect The Negative Battery Terminal To The 6(+S) Terminal 0V 3.3±1 Sec. E101527J09 (c) (5) Connect the negative (-) battery terminal to the 6 (+S) terminal of the connector and check the voltage between the 5 (EW) terminal and the 7 (+1) terminal when the intermittent wiper relay is operated. Standard: As shown in the illustration OPERATION CHECK (FRONT WASHER) (1) Turn front wiper switch OFF. (2) Connect the negative (-) battery terminal to the 5 (EW) terminal and the 6 (+S) terminal, and connect the positive (+) battery terminal to the 8 (+B) terminal of the connector. Washer Switch ON OFF 7(+1) 5(EW) 10 to 14V Voltage 0V Between Terminals Approx. 0.3 Sec. Approx. 2.2 Sec. (3) Using the tester, connect the negative (-) terminal of the tester to the 5 (EW) terminal, and connect the positive (+) terminal of the tester to the 7 (+1) terminal of the connector. Then check the voltage between the 5 (EW) terminal and the 7 (+1) terminal when the washer switch is turned ON and OFF. Standard: As shown in the illustration E036383J05

26 25 WASHER NOZZLE BODY WIPER AND ELECTRICAL WIPER AND WASHER - WASHER NOZZLE INSPECTION 1. CHECK WASHER NOZZLE (a) With the engine running, check the position of the spray of the washer fluid. HINT: Check the left handle using the same standard. Standard: Within the area shown in the illustration E129772J01

27 WIPER AND WASHER - WINDSHIELD WASHER JAR ASSEMBLY 26 BODY WIPER AND ELECTRICAL WASHER WINDSHIELD WASHER JAR ASSEMBLY COMPONENTS WINDSHIELD WASHER JAR ASSEMBLY E130015J01 REMOVAL 1. REMOVE WINDSHIELD WASHER JAR ASSEMBLY (1) Remove the 2 bolts and the connector. Then remove the windshield washer jar assembly. E127789

28 27 INSTALLATION WIPER AND WASHER - WINDSHIELD WASHER JAR ASSEMBLY 1. INSTALL WINDSHIELD WASHER JAR ASSEMBLY (1) Temporarily install the windshield washer jar assembly to the vehicle body and connect the connector. (2) Install the 2 bolts. E129448

29 WIPER AND WASHER - WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY BODY WIPER AND ELECTRICAL WASHER ON-VEHICLE INSPECTION CHECK WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY (FRONT SPRAY POSITION) (a) CHECK OPERATION (1) With the windshield washer motor and pump assembly installed in the windshield washer jar assembly, add washer fluid to the windshield washer jar assembly. E (2) Check the pressure feed of the washer liquid on the front side when the battery minus (-) is connected to terminal 2 and the battery positive (+) is connected to terminal 1 of the windshield washer motor & pump assembly. 2. CHECK WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY (REAR SPRAY POSITION) (a) CHECK OPERATION (1) With the windshield washer motor and pump assembly installed in the windshield washer jar assembly, add washer fluid to the windshield washer jar assembly. (2) Check the pressure feed of the washer liquid on the front side when the battery minus (-) is connected to terminal 2 and the battery positive (+) is connected to terminal 1 of the windshield washer motor & pump assembly. E066244

30 29 WIPER AND WASHER - REAR WASHER NOZZLE BODY WIPER AND ELECTRICAL WASHER REAR WASHER NOZZLE INSPECTION 1. CHECK REAR WASHER NOZZLE (1) With the engine running, check the position of the spray of the washer fluid. Standard: Within the area shown in the illustration E129773J01 TO INDEX TO NEXT SECTION