Contents. I. Dantherm Product Index II. Understanding Dantherm Model Identification... 4

Transcription

1 Closed-Loop Cooling for Electronics & Communications Enclosures

2 Contents I. Dantherm Product Index... 3 II. Understanding Dantherm Model Identification... 4 III. Classic Series Air-Conditioners Classic 20 Air-conditioner 2,000 BTU / Hr Classic 30 Air-conditioner 4,000 BTU / Hr Classic 30 Air-conditioner 7,500 BTU / Hr Classic 47 Air-conditioner 10,000 BTU / Hr Classic 50 Air-conditioner 12,500 BTU / Hr Classic 50 Air-conditioner 13,000 BTU / Hr Classic 53 Air-conditioner 19,000 BTU / Hr Classic Top-Mount Air-Conditioners Class 1 Div 1 Hazardous Duty Air-Conditioner IV. Pinnacle Series Air-to-Air Heat Exchangers 23 Pinnacle Heat Exchanger 11 W / o F Pinnacle Heat Exchanger 15 W / o F Pinnacle Heat Exchanger 35 W / o F Pinnacle Heat Exchanger 45 W / o F Pinnacle Heat Exchanger 55 W / o F Pinnacle Heat Exchanger 100 W / o F V. Custom Products and Design Capabilities VI. Dantherm Technologies and Innovations & Summary Focus. Trust. Initiative. 2

3 Dantherm Standard Product Index Classic Series Air-Conditioners Product Model # Performance Voltages Refrigerant Classic 20 CS ,000 BTU / Hr A, B5, B6 134a Classic 30 CS ,000 BTU / Hr A, B 134a Classic 30 Classic 47 CS (previously CS030060) CS (previously CS047120) 7,500 BTU / Hr A, B5, B6 R-22 10,000 BTU / Hr B R-22 Classic 50 CS ,500 BTU / Hr B R-22 Classic 50 CS ,000 BTU / Hr B R-22 Classic 53 CS ,000 BTU / Hr B 134a Rack/Top Mount CS ,500 BTU / Hr A, B 134a Rack/Top Mount CS ,500 BTU / Hr A, B R-22 A = 115V 1 Ph 50/60 Hz B = 208/ 230V 1 Ph 50/60 Hz B5 = 230V 1 Ph 50 Hz B6 = 230V 1 Ph 60 Hz Pinnacle Series Heat Exchangers Product Model # Performance Voltages Refrigerant 23" Pinnacle PS W / o F A, B, Z N/A Pinnacle 2" PS W / o F A, B, Z N/A Pinnacle 6" PS W / o F A, B, Z N/A Pinnacle 6" PS W / o F A, B, Z N/A Pinnacle 8" PS W / o F A, B, Z N/A 60" Pinnacle PS W / o F B N/A A = 115V 1 Ph 50/60 Hz B = Z = 230V 1 Ph 50/60 Hz 48V DC 3

4 Understanding Dantherm Model Identification Dantherm Classic Series Air-Conditioners C=Classic S= Standard Configuration X= Custom Configuration 030 = Height Of Unit = 2000 BTU/Hr 040 = 4000 BTU/Hr 060 = 6000 BTU/Hr CS030040A-H004 Example Number Translation Classic 30 with Standard Construction 4,000 BTU/Hr 115 V 1Ph 50-60Hz Includes a 400 Watt Heater Option Option Codes H _ = Heater. Requires an additional 3 digits to refer to heater rating. ex: H004=400W A = 115Volt/1Ph/50-60 Hz B = 230Volt/1Ph/50-60Hz B5 = 220Volt/1Ph/50Hz B6 = 230V/1Ph/60Hz Z = 48v DC Dantherm Pinnacle Series Heat Exchangers P=Pinnacle S= Standard Configuration X= Custom Configuration 023 = Height Of Unit = Watts per degree F 015 = Watts per degree F 035 = Watts per degree F 045 = Watts per degree F 055 = Watts per degree F 100 = Watts per degree F PS023011A-T1 Example Number Translation Pinnacle with Standard Construction 35 Watts per degree F 115V 1Ph 50-60Hz Includes a 400 Watt Heater Option Option Codes T= Thermostat GR = Designed for GR testing S = Speed Controller M= Stainless Steel Cover P= Cover Color option A = 115Volt/1Phase/50-60 Hz B = 230Volt/1Phase/50-60Hz Z = 48v DC 4

5 Dantherm CLASSIC 20 Air-Conditioner Model CS ,000 BTU / Hr. DANTHERM S CLASSIC Line of Air-conditioners is specifically designed for the removal of heat from cabinets containing temperature-sensitive electrical, electronic, or telecommunications equipment. Closed-loop cooling maintains a clean, sealed internal environment to insure optimum performance and maximum life of the enclosed electronics, while protecting against the intrusion of airborne contaminants and humidity. Dantherm Part Number Product Description 2,000 BTU / Hr CS A or B 115V or 230V 1 Ph, Hz Dimensions: 20 H X 10 W X 9 D -H005 Optional: Integrated 500 Watt Heater Standard Features: Advanced Printed Circuit Control Board Built-in Lead Lag Controller Integral Return Air Thermostat Integrated Self Test Switch Infrared Diagnostic Connection Port Hot Spot Sensor Input Failure Alarm Output Variable Heating and Cooling Settings Condenser Fan on/off Controlled Coated Condenser Coil UL \ cul Recognized Outdoor Rated to UL o F to +113 o F Operating Range High Pressure Switch Low Pressure Switch (inc. bypass timer) Low Ambient Operation Short Cycle Protection High Quality Powder-coated Cover 5

6 Dantherm CLASSIC 20 Air-Conditioner Dimensional Diagram Mounting Interface 6

7 Dantherm CLASSIC 20 Air-Conditioner Classic Air-flow Diagram Component Locations General Performance Data Dantherm Model BTU/Hr Watts Removal Voltage Hz Ph Full Load Amps Breaker / Fuse Size Approx Wt. lbs. / Kg. CS020020A 2, V 50 / / 25 CS020020B5 1, V / 25 CS020020B6 2, V / 25 Capacity ratings shown above are based on 95 o F (35 o C) return air temperature to cabinet in 95 o F (35 o C) ambient conditions at nominal voltage and unimpeded resistance to air flow. 7

8 Dantherm CLASSIC 20 Air-Conditioner ACG2 Controller LED Trip Indicator Microprocessor Infra-Red LED Alarm Contacts Self-Test Button Cooling Dial Settings from 68 F (20 C) to 104 F (40 C) Heating Dial Settings from 41 F (5 C) to 59 F (15 C) ACG2 Self-Test Button Function A self-test button is provided on the control board of each Classic panel-mount air-conditioner. Simply pressing and holding this button for 6 seconds will activate the self-test sequence as shown in the chart below. During this test, the installer or technician may observe the air-conditioner for the expected function and duration, indicating that all are operating properly. On completion of the self-test, the air-conditioner automatically returns to normal running condition. The control board is also outfitted with an Infrared LED diagnostic port. Optional software and an infrared / RS232 Interface cable are available from Dantherm, enabling the unit to be connected to a portable laptop computer. In this manner, comprehensive and detailed real-time operational data may be observed, diagnostics run, and data imported onto the laptop. Call for more details. Sequence Description Evaporator Fan Heater Compressor Condenser Fan Duration 1 Internal Fan only ON OFF OFF OFF 30 Seconds 2 Heater ON ON OFF OFF 35 Seconds 3 Internal Fan only ON OFF OFF OFF 20 Seconds 4 Compressor & Condenser fan ON OFF ON ON 75 Seconds 5 Internal Fan only ON OFF OFF OFF 30 Seconds 8

9 Dantherm CLASSIC 20 Air-Conditioner Alarm Capabilities All Dantherm Classic units have built-in alarm capabilities programmed into the control board. Failure Modes The following conditions will activate the failure alarm output on terminals 7 and 8: Loss of supply voltage Low Pressure (< 10 psi for 300 seconds) High Pressure (> 400 / 500 psi) Low or no current to compressor (less than 1 amp) High Return Air Temperature (18 o F / 10 o C higher than cooling set point) Low Return Air Temperature (9 o F / 5 o C lower than heater set point) Alarm Connections The alarm cable consists of four wires: Black wire: connected to terminal 7 on the control board Red wire: connected to terminal 8 on the control board White wire: not used Green wire: not used Alarm Description Only the red and black wires are used and are connected to terminals 7 and 8 of the control board. Terminals 7 and 8 operate as a normally closed contactor and open upon failure. During normal operation, a relay is energized, providing continuity between terminals 7 and 8. When a failure is detected, the relay is deenergized such that there is no continuity between terminals 7 and 8. A low voltage signal (up to 50V DC and 0.1 amps) may be connected to the contactors for external alarm capabilities. Performance Curves 9

10 Dantherm CLASSIC 30 Air-Conditioners Model CS ,000 BTU / Hr. and Model CS ,500 BTU / Hr. DANTHERM S CLASSIC Line of Air-conditioners is specifically designed for the removal of heat from cabinets containing temperature-sensitive electrical, electronic, or telecommunications equipment. Closed-loop cooling maintains a clean, sealed internal environment to insure optimum performance and maximum life of the enclosed electronics, while protecting against the intrusion of airborne contaminants and humidity. Dantherm Part Number Product Description 4,000 BTU / Hr CS A or B 115V or 230V 1 Ph, Hz Dimensions: 30 H X 19 W X 9 D 7,500 BTU / Hr CS A or B 115V or 230V 1 Ph, Hz Dimensions: 30 H X 19 W X 11 D -H004 Optional: Integrated 400 Watt Heater -H008 Optional: Integrated 800 Watt Heater -H012 Optional: Integrated 1200 Watt Heater 10

11 Dantherm CLASSIC 30 Air-Conditioners Standard Features: Advanced Printed Circuit Control Board Built-in Lead Lag Controller Integral Return Air Thermostat Integrated Self Test Switch Infrared Diagnostic Connection Port Hot Spot Sensor Input Failure Alarm Output Variable Heating and Cooling Settings Condenser Fan on/off Controlled Coated Condenser Coil UL \ cul Recognized Outdoor Rated to UL o F to +131 o F Operating Range High Pressure Switch Low Pressure Switch (inc. bypass timer) Low Ambient Operation Short Cycle Protection Options for GR-487-CORE modifications High Quality Powder-coated Cover Classic Air-flow Diagram Inside View 11

12 Dantherm CLASSIC 30 Air-Conditioner General Performance Data Dantherm Model BTU/Hr Watts Removal Voltage Hz Ph Full Load Amps Breaker / Fuse Size Approx Wt. lbs. / Kg. CS030040A 4,000 1, V 50 / / 45 CS030040B 4,000 1, V 50 / / 45 CS030075A 7,500 2, V 50 / / 48 CS030075B 7,500 2, V 50 / / 48 Capacity ratings shown above are based on 95 o F (35 o C) return air temperature to cabinet in 95 o F (35 o C) ambient conditions at nominal voltage and unimpeded resistance to air flow. ACG2 Controller LED Trip Indicator Microprocessor Infra-Red LED Alarm Contacts Self-Test Button Cooling Dial Settings from 68 F (20 C) to 104 F (40 C) Heating Dial Settings from 41 F (5 C) to 59 F (15 C) 12

13 Dantherm CLASSIC 30 Air-Conditioner ACG2 Self-Test Button Function A self-test button is provided on the control board of each Classic panel-mount air-conditioner. Simply pressing and holding this button for 6 seconds will activate the self-test sequence as shown in the chart below. During this test, the installer or technician may observe the air-conditioner for the expected function and duration, indicating that all are operating properly. On completion of the self-test, the air-conditioner automatically returns to normal running condition. The control board is also outfitted with an Infrared LED diagnostic port. Optional software and an infrared / RS232 Interface cable are available from Dantherm, enabling the unit to be connected to a portable laptop computer. In this manner, comprehensive and detailed real-time operational data may be observed, diagnostics run, and data imported onto the laptop. Call for more details. Sequence Description Evaporator Fan Heater Compressor Condenser Fan Duration 1 Internal Fan only ON OFF OFF OFF 30 Seconds 2 Heater ON ON OFF OFF 35 Seconds 3 Internal Fan only ON OFF OFF OFF 20 Seconds 4 Compressor & Condenser fan ON OFF ON ON 75 Seconds 5 Internal Fan only ON OFF OFF OFF 30 Seconds Alarm Capabilities All Dantherm Classic units have built-in alarm capabilities programmed into the control board. Failure Modes The following conditions will activate the failure alarm output on terminals 7 and 8: Loss of supply voltage Low Pressure (< 10 psi for 300 seconds) High Pressure (> 400 / 500 psi) Low or no current to compressor (less than 1 amp) High Return Air Temperature (18 o F / 10 o C higher than cooling set point) Low Return Air Temperature (9 o F / 5 o C lower than heater set point) Alarm Connections The alarm cable consists of four wires: Black wire: connected to terminal 7 on the control board Red wire: connected to terminal 8 on the control board White wire: not used Green wire: not used Alarm Description Only the red and black wires are used and are connected to terminals 7 and 8 of the control board. Terminals 7 and 8 operate as a normally closed contactor and open upon failure. During normal operation, a relay is energized, providing continuity between terminals 7 and 8. When a failure is detected, the relay is deenergized such that there is no continuity between terminals 7 and 8. A low voltage signal (up to 50V DC and 0.1 amps) may be connected to the contactors for external alarm capabilities. 13

14 Dantherm CLASSIC 30 Air-Conditioner Dimensional Diagram Mounting Interface 4,000 BTU CLASSIC 30 Air-Conditioner **Mounting pattern for GR version only, call or to request the standard version. 14

15 Dantherm CLASSIC 30 Air-Conditioner Dimensional Diagram Mounting Interface 7,500 BTU CLASSIC 30 Air-Conditioner 15

16 Dantherm CLASSIC 30 Air-Conditioner Performance Curves 4,000 BTU CLASSIC 30 Air-Conditioner 7, 500 BTU CLASSIC 30 Air- Conditioner 16

17 Dantherm CLASSIC 47 Air-Conditioner Model CS047100B 10,000 BTU / Hr. DANTHERM S CLASSIC Line of Air-conditioners is specifically designed for the removal of heat from cabinets containing temperature-sensitive electrical, electronic, or telecommunications equipment. Closed-loop cooling maintains a clean, sealed internal environment to insure optimum performance and maximum life of the enclosed electronics, while protecting against the intrusion of airborne contaminants and humidity. Dantherm Part Number Product Description 10,000 BTU / Hr CS047100B 230V 1 Ph, Hz Dimensions: 47 H X 19 W X 12 D -H008, H012, H015, H030 Optional: Integrated 800W, 1200W, or 1500W Heater Standard Features: Advanced Printed Circuit Control Board Built-in Lead Lag Controller Integral Return Air Thermostat Integrated Self Test Switch Infrared Diagnostic Connection Port Hot Spot Sensor Input Failure Alarm Output Variable Heating and Cooling Settings Condenser Fan on/off Controlled Coated Condenser Coil UL \ cul Recognized Outdoor Rated to UL o F to +131 o F Operating Range High Pressure Switch Low Pressure Switch (inc. bypass timer) Low Ambient Operation Short Cycle Protection Options for GR-487-CORE modifications High Quality Powder-coated Cover 17

18 Dantherm CLASSIC 47 Air-Conditioner CLASSIC Air-Flow Diagram Dimensional Diagram Mounting Interface 10,000 BTU CLASSIC 47 Air-Conditioner 18

19 Dantherm CLASSIC 47 Air-Conditioner General Performance Data Dantherm Model BTU/Hr Watts Removal Voltage Hz Ph Full Load Amps Breaker / Fuse Size Approx Wt. lbs. / Kg. CS047100B 10,000 3, V / 70 CS047100B 9,000 2, V / 70 Capacity ratings shown above are based on 95 o F (35 o C) return air temperature to cabinet in 95 o F (35 o C) ambient conditions at nominal voltage and unimpeded resistance to air flow. ACG2 Controller LED Trip Indicator Microprocessor Infra-Red LED Alarm Contacts Self-Test Button Cooling Dial Settings from 68 F (20 C) to 104 F (40 C) Heating Dial Settings from 41 F (5 C) to 59 F (15 C) 19

20 Dantherm CLASSIC 47 Air-Conditioner ACG2 Self-Test Button Function A self-test button is provided on the control board of each Classic panel-mount air-conditioner. Simply pressing and holding this button for 6 seconds will activate the self-test sequence as shown in the chart below. During this test, the installer or technician may observe the air-conditioner for the expected function and duration, indicating that all are operating properly. On completion of the self-test, the air-conditioner automatically returns to normal running condition. The control board is also outfitted with an Infrared LED diagnostic port. Optional software and an infrared / RS232 Interface cable are available from Dantherm, enabling the unit to be connected to a portable laptop computer. In this manner, comprehensive and detailed real-time operational data may be observed, diagnostics run, and data imported onto the laptop. Call for more details. Sequence Description Evaporator Fan Heater Compressor Condenser Fan Duration 1 Internal Fan only ON OFF OFF OFF 30 Seconds 2 Heater ON ON OFF OFF 35 Seconds 3 Internal Fan only ON OFF OFF OFF 20 Seconds 4 Compressor & Condenser fan ON OFF ON ON 75 Seconds 5 Internal Fan only ON OFF OFF OFF 30 Seconds Alarm Capabilities All Dantherm Classic units have built-in alarm capabilities programmed into the control board. Failure Modes The following conditions will activate the failure alarm output on terminals 7 and 8: Loss of supply voltage Low Pressure (< 10 psi for 300 seconds) High Pressure (> 400 / 500 psi) Low or no current to compressor (less than 1 amp) High Return Air Temperature (18 o F / 10 o C higher than cooling set point) Low Return Air Temperature (9 o F / 5 o C lower than heater set point) Alarm Connections The alarm cable consists of four wires: Black wire: connected to terminal 7 on the control board Red wire: connected to terminal 8 on the control board White wire: not used Green wire: not used Alarm Description Only the red and black wires are used and are connected to terminals 7 and 8 of the control board. Terminals 7 and 8 operate as a normally closed contactor and open upon failure. During normal operation, a relay is energized, providing continuity between terminals 7 and 8. When a failure is detected, the relay is deenergized such that there is no continuity between terminals 7 and 8. A low voltage signal (up to 50V DC and 0.1 amps) may be connected to the contactors for external alarm capabilities. 20

21 Dantherm CLASSIC 47 Air-Conditioner Performance Curves 21

22 Dantherm CLASSIC 50 Air-Conditioner Model CS050125B 12,500 BTU / Hr. and Model CS050130B 13,000 BTU / Hr. DANTHERM S CLASSIC Line of Air-conditioners is specifically designed for the removal of heat from cabinets containing temperature-sensitive electrical, electronic, or telecommunications equipment. Closed-loop cooling maintains a clean, sealed internal environment to insure optimum performance and maximum life of the enclosed electronics, while protecting against the intrusion of airborne contaminants and humidity. Dantherm Part Number Product Description 12,500 BTU / Hr CS050125B 230V 1 Ph, Hz Dimensions: 50 H X 19 W X 15 D -H015 or -H030 Optional: 1500W or 3000W Heater 13,000 BTU / Hr CS050130B 230V 1 Ph, Hz Dimensions: 50 H X 19 W X 13 D -H015 or -H030 Optional: 1500W or 3000W Heater 22

23 Dantherm CLASSIC 50 Air-Conditioner Standard Features: Advanced Printed Circuit Control Board Built-in Lead Lag Controller Integral Return Air Thermostat Integrated Self Test Switch Infrared Diagnostic Connection Port Hot Spot Sensor Input Failure Alarm Output Variable Heating and Cooling Settings Condenser Fan on/off Controlled Coated Condenser Coil UL \ cul Recognized Outdoor Rated to UL o F to +131 o F Operating Range High Pressure Switch Low Pressure Switch (inc. bypass timer) Low Ambient Operation Short Cycle Protection Options for GR-487-CORE modifications High Quality Powder-coated Cover CLASSIC Air-Flow Diagram 23

24 Dantherm CLASSIC 50 Air-Conditioner General Performance Data Dantherm Model BTU/Hr Watts Removal Voltage Hz Ph Full Load Amps Breaker / Fuse Size Approx Wt. lbs. / Kg. CS050125B 12,500 3, V 50 / *15 / / 70 CS050130B 13,000 3, V 50 / *15 / / 70 Capacity ratings shown above are based on 131 o F (55 o C) return air temperature to cabinet in 131 o F (55 o C) ambient conditions at nominal voltage and unimpeded resistance to air flow. * NOTE: Breaker / Fuse requirement with no heater and 1500W heater: 15 amp. Breaker / Fuse requirement with 3000W heater: 20 amp. ACG2 Controller LED Trip Indicator Microprocessor Infra-Red LED Alarm Contacts Self-Test Button Cooling Dial Settings from 68 F (20 C) to 104 F (40 C) Heating Dial Settings from 41 F (5 C) to 59 F (15 C) 24

25 Dantherm CLASSIC 50 Air-Conditioner ACG2 Self-Test Button Function A self-test button is provided on the control board of each Classic panel-mount air-conditioner. Simply pressing and holding this button for 6 seconds will activate the self-test sequence as shown in the chart below. During this test, the installer or technician may observe the air-conditioner for the expected function and duration, indicating that all are operating properly. On completion of the self-test, the air-conditioner automatically returns to normal running condition. The control board is also outfitted with an Infrared LED diagnostic port. Optional software and an infrared / RS232 Interface cable are available from Dantherm, enabling the unit to be connected to a portable laptop computer. In this manner, comprehensive and detailed real-time operational data may be observed, diagnostics run, and data imported onto the laptop. Call for more details. Sequence Description Evaporator Fan Heater Compressor Condenser Fan Duration 1 Internal Fan only ON OFF OFF OFF 30 Seconds 2 Heater ON ON OFF OFF 35 Seconds 3 Internal Fan only ON OFF OFF OFF 20 Seconds 4 Compressor & Condenser fan ON OFF ON ON 75 Seconds 5 Internal Fan only ON OFF OFF OFF 30 Seconds Alarm Capabilities All Dantherm Classic units have built-in alarm capabilities programmed into the control board. Failure Modes The following conditions will activate the failure alarm output on terminals 7 and 8: Loss of supply voltage Low Pressure (< 10 psi for 300 seconds) High Pressure (> 400 / 500 psi) Low or no current to compressor (less than 1 amp) High Return Air Temperature (18 o F / 10 o C higher than cooling set point) Low Return Air Temperature (9 o F / 5 o C lower than heater set point) Alarm Connections The alarm cable consists of four wires: Black wire: connected to terminal 7 on the control board Red wire: connected to terminal 8 on the control board White wire: not used Green wire: not used Alarm Description Only the red and black wires are used and are connected to terminals 7 and 8 of the control board. Terminals 7 and 8 operate as a normally closed contactor and open upon failure. During normal operation, a relay is energized, providing continuity between terminals 7 and 8. When a failure is detected, the relay is deenergized such that there is no continuity between terminals 7 and 8. A low voltage signal (up to 50V DC and 0.1 amps) may be connected to the contactors for external alarm capabilities. 25

26 Dantherm CLASSIC 50 Air-Conditioner Dimensional Diagram Mounting Interface 12,500 BTU CLASSIC 50 Air-Conditioner 13,000 BTU CLASSIC 50 Air-Conditioner 26

27 Dantherm CLASSIC 50 Air-Conditioner Performance Curves 13,000 BTU CLASSIC 50 Air-Conditioner 27

28 Dantherm CLASSIC 53 Air-Conditioner Model CS053190B 19,000 BTU / Hr. DANTHERM S CLASSIC Line of Air-conditioners is specifically designed for the removal of heat from cabinets containing temperature-sensitive electrical, electronic, or telecommunications equipment. Closed-loop cooling maintains a clean, sealed internal environment to insure optimum performance and maximum life of the enclosed electronics, while protecting against the intrusion of airborne contaminants and humidity. Dantherm Part Number Product Description 19,000 BTU / Hr CS053190B 230V 1 Ph, 60 Hz Dimensions: 53 H X 23 W X 16.5 D -H W Heater Standard Features: Advanced Printed Circuit Control Board Built-in Lead Lag Controller Integral Return Air Thermostat Integrated Self Test Switch Infrared Diagnostic Connection Port Hot Spot Sensor Input Failure Alarm Output Variable Heating and Cooling Settings Condenser Fan on/off Controlled Coated Condenser Coil UL \ cul Recognized Outdoor Rated to UL o F to +131 o F Operating Range High Pressure Switch Low Pressure Switch (inc. bypass timer) Low Ambient Operation Short Cycle Protection Options for GR-487-CORE modifications High Quality Powder-coated Cover 28

29 Dantherm CLASSIC 53 Air-Conditioner CLASSIC Air-Flow Diagram Dimensional Diagram Mounting Interface 29

30 Dantherm CLASSIC 53 Air-Conditioner Dantherm Model BTU/Hr Watts Removal Voltage Hz Ph Full Load Amps Breaker / Fuse Size Approx Wt. lbs. / Kg. CS053190B 19,000 5, V 60 1 TBC /113 Capacity ratings shown above are based on 131 o F (55 o C) return air temperature to cabinet in 131 o F (55 o C) ambient conditions at nominal voltage and unimpeded resistance to air flow. ACG2 Controller LED Trip Indicator Microprocessor Infra-Red LED Alarm Contacts Self-Test Button Cooling Dial Settings from 68 F (20 C) to 104 F (40 C) Heating Dial Settings from 41 F (5 C) to 59 F (15 C) 30

31 Dantherm CLASSIC 53 Air-Conditioner ACG2 Self-Test Button Function A self-test button is provided on the control board of each Classic panel-mount air-conditioner. Simply pressing and holding this button for 6 seconds will activate the self-test sequence as shown in the chart below. During this test, the installer or technician may observe the air-conditioner for the expected function and duration, indicating that all are operating properly. On completion of the self-test, the air-conditioner automatically returns to normal running condition. The control board is also outfitted with an Infrared LED diagnostic port. Optional software and an infrared / RS232 Interface cable are available from Dantherm, enabling the unit to be connected to a portable laptop computer. In this manner, comprehensive and detailed real-time operational data may be observed, diagnostics run, and data imported onto the laptop. Call for more details. Sequence Description Evaporator Fan Heater Compressor Condenser Fan Duration 1 Internal Fan only ON OFF OFF OFF 30 Seconds 2 Heater ON ON OFF OFF 35 Seconds 3 Internal Fan only ON OFF OFF OFF 20 Seconds 4 Compressor & Condenser fan ON OFF ON ON 75 Seconds 5 Internal Fan only ON OFF OFF OFF 30 Seconds Alarm Capabilities All Dantherm Classic units have built-in alarm capabilities programmed into the control board. Failure Modes The following conditions will activate the failure alarm output on terminals 7 and 8: Loss of supply voltage Low Pressure (< 10 psi for 300 seconds) High Pressure (> 400 / 500 psi) Low or no current to compressor (less than 1 amp) High Return Air Temperature (18 o F / 10 o C higher than cooling set point) Low Return Air Temperature (9 o F / 5 o C lower than heater set point) Alarm Connections The alarm cable consists of four wires: Black wire: connected to terminal 7 on the control board Red wire: connected to terminal 8 on the control board White wire: not used Green wire: not used Alarm Description Only the red and black wires are used and are connected to terminals 7 and 8 of the control board. Terminals 7 and 8 operate as a normally closed contactor and open upon failure. During normal operation, a relay is energized, providing continuity between terminals 7 and 8. When a failure is detected, the relay is deenergized such that there is no continuity between terminals 7 and 8. A low voltage signal (up to 50V DC and 0.1 amps) may be connected to the contactors for external alarm capabilities. 31

32 Dantherm CLASSIC 53 Air-Conditioner Performance Curves 19,000 BTU CLASSIC 53 Air-Conditioner Capacity Curve 19K - November 30, Load Btu/hr ºC Ambient 45ºC Ambient 55ºC Ambient Internal Temperature (Return) ºC 32

33 Dantherm CLASSIC Top-Mount Air-Conditioner Model CS ,500 BTU / Hr. Model CS ,500 BTU / Hr. DANTHERM S CLASSIC Line of Air-conditioners is specifically designed for the removal of heat from cabinets containing temperature-sensitive electrical, electronic, or telecommunications equipment. Closed-loop cooling maintains a clean, sealed internal environment to insure optimum performance and maximum life of the enclosed electronics, while protecting against the intrusion of airborne contaminants and humidity. Dantherm Part Number CS A or B CS A or B Product Description 3,500 BTU / Hr 115V or 230V 1 Ph, Hz Dimensions: 12-1/4 H X 17-1/4 W X 22 D 5,500 BTU / Hr 115V or 230V 1 Ph, Hz Dimensions: 16-1/4 H X 17-1/4 W X 22 D -H004 or -H008 Optional: Integrated 400W or 800W Heater 33

34 Dantherm CLASSIC Top-Mount Air-Conditioner General Performance Data Dantherm Model BTU/Hr Watts Removal Voltage Hz Ph Full Load Amps Breaker / Fuse Size Approx Wt. lbs. / Kg. CS012035A 3, V 50 / / 58 CS012035B 3, V 50 / / 58 CS016055A 5, V 50 / / 65 CS016055B 5, V 50 / / 65 Capacity ratings shown above are based on 95 o F (35 o C) return air temperature to cabinet in 95 o F (35 o C) ambient conditions at nominal voltage and unimpeded resistance to air flow. Standard Features Closed Loop Cooling Rated for Outdoor Use to UL o F to +131 o F Operating Range High Pressure Switch Low Pressure Switch (inc. bypass timer) Low Ambient Operation Condensation Removal System Short Cycle Protection High Performance Fans UL \ cul Recognized High Quality Powder-coated Cover Product Diagram Component Locations 34

35 Dantherm CLASSIC Top-Mount Air-Conditioner Dimensional Diagram Mounting Interface Classic Top-Mount Air-flow Diagram Introducing. 35

36 Hazardous Duty Cooling At Its Best Completely New Design for explosive environments Cooling unit specifically designed for Class 1, Division 1 hazardous locations All electrical components / connections located on internal loop Operational capacity of 10,000 BTU / hr Available in 480-Volt and 230-Volt 1 Phase High and low pressure switches w/ Lock-out Relay Compressor overload protection w/ Lock-out Relay No electronic controls. simple on / off control Operational temperature up to 131 o F Efficient Rotary Compressor Low ambient control Ambient air filter Alarm output 36

37 Pinnacle Series Air-to-Air Heat Exchangers * Efficient COOLING for indoor & outdoor electronics cabinets & enclosures * DANTHERM S PINNACLE Heat Exchangers are specifically designed for the removal of heat from cabinets containing temperature-sensitive electrical, electronic, or telecommunications equipment. Closed-loop cooling maintains a clean, sealed internal environment to insure optimum performance and maximum life of the enclosed electronics, while protecting against the intrusion of airborne contaminants and humidity. Quality Efficiency Durability Versatility Simplicity Available in 48V DC and 115V and 230V AC Voltages. Closed-loop cooling removes heat and protects electronics from humidity & contaminants. Options for GR-487-CORE compliance for corrosion resistance and wind-driven rain. Compact design allows for wide variety of mounting configurations and applications. Units mount quickly and easily to outside of cabinet or enclosure. Longest standard warrantee in the industry at 18 months. UL Recognized or Listed to UL 484 for outdoor use. Optional temperature control and alarm strategies. Units are manufactured here in the United States. Efficient coated aluminum heat-transfer core. Low maintenance; CFC and refrigerant free. 37

38 Pinnacle Series Air-to-Air Heat Exchangers Every Pinnacle Series Heat Exchanger incorporates an efficient and durable epoxy-coated aluminum heat-transfer core manufactured on state-of-the-art equipment exclusive to Dantherm. General Performance Data Model Number Voltage Performance in Watts / o F Performance in Watts / o C Dimensions Full Load Amps. Breaker / Fuse Weight (lbs.) PS023011A 115V AC "H x 12"W x 5"D PS023011B 230V AC "H x 12"W x 5"D PS023011Z 48V DC "H x 12"W x 5"D PS035015A 115V AC "H x 18"W x 3.6"D PS035015B 230V AC "H x 18"W x 3.6"D PS035015Z 48V DC "H x 18"W x 3.6"D PS035035A 115V AC "H x 18"W x 6.8"D PS035035B 230V AC "H x 18"W x 6.8"D PS035035Z 48V DC "H x 18"W x 6.8"D PS035045A 115V AC "H x 18"W x 6.8"D PS035045B 230V AC "H x 18"W x 6.8"D PS035045Z 48V DC "H x 18"W x 6.8"D PS035055A 115V AC "H x 18"W x 8.8"D PS035055B 230V AC "H x 18"W x 8.8"D PS035055Z 48V DC "H x 18"W x 8.8"D PS060100B 230V AC "H x 24W" x 14"D

39 Pinnacle Series Air-to-Air Heat Exchangers Dimensional Diagrams Mounting Interfaces Pinnacle PS Models Pinnacle Series Air-to-Air Heat Exchangers 39

40 Pinnacle Series Air-to-Air Heat Exchangers Dimensional Diagrams Mounting Interfaces Pinnacle PS0350XX Models Pinnacle PS060100B Model 40

41 Pinnacle Series Air-to-Air Heat Exchangers Dimensional Diagrams Mounting Interfaces Pinnacle PS Models 41

42 Pinnacle Series Air-to-Air Heat Exchangers Heat Exchanger Performance Curves Total Heat Dissipation (Watts) Temperature Delta in 0 F PS PS PS PS PS PS

43 Dantherm Custom Products Air-Conditioners & Heat Exchangers Ask about Dantherm Global Design Capabilities 43

44 Introducing. Dantherm New Technologies & Innovations Plastic Foil Heat Exchanger Solutions Improved fuel cell technologies Pressurized ventilation systems Others in development 44

45 Global Expertise, Resources, and Capabilities. Local Commitment to Quality Products and Exceptional Customer Service. Focus. Trust. Initiative. 45

46 For Personal Assistance or Ordering: The information contained in this document is subject to change without notification. For personal assistance in product sizing, pricing, or model selection, call, fax, or your questions, specifications, or requirements to: Dantherm Contact Responsibility Title Direct Phone Address Rick Gromlovits Commercial Sales Manager Electronics Cooling (704) Rick Schmidt Technical Engineering Manager (864) Lourdes Sisk Customer Service & Marketing Customer Service (864) & Marketing Manager Dantherm Air Handling, Inc Orchard Park Blvd. Spartanburg, SC Phone: (864) Fax: (864)