TECHNICAL GUIDE LISTED

Transcription

1 T I I I T G TECHNICAL GUIDE SPLIT-SYSTEM AIR CONDITIONERS 10 SEER AC012M102 THRU AC030M1021 (1 THRU 2.5 NOMINAL TONS, 1 PH) AC036X102 THRU 60 (3 THRU 5 NOMINAL TONS, 1 PH) AC036X10(3,4) THRU 60 (3 THRU 5 NOMINAL TONS, 3 PH) This product was manufactured in a plant whose quality system is certified/registered as being in conformity with ISO U R A C T MA N U F R E C E UN I R T I C ER T A R I A RY F F I E D E Q U I C A T T S A Certification applies only when the complete system is listed with ARI. AC012M1021 THRU 030 AC036X1021 THRU 060 AC036X10(31,41) THRU 060 LISTED Due to continuous product improvement, specifications are subject to change without notice. Visit us on the web at for the most up-to-date technical information. Additional rating information can be found at T R P ON O T M E N S A R I AI E CT N D A R R - C I D AS ONDI ON S 2 O I C 1 0 OM P NI N G OF L Y N I W IT H DESCRIPTION Rev. E (0405) The 10 SEER Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be custom-matched with one of UPG s complete line of evaporator sections, each designed to serve a specific function. Matching Air Handlers are available for upflow, downflow or horizontal applications to provide a complete system. Electric Heaters are available if required. Add-On coils are available for use with upflow, downflow or horizontal furnaces and air handlers. WARRANTY 5-year limited parts warranty. 5-year limited compressor warranty. FEATURES QUALITY CONDENSER COILS - The coil is constructed of enhanced copper tube and aluminum fins. COIL PROTECTION - Coils are protected from damage by a polymer mesh applied between the coil face, and a PVC coated steel coil guard. PROTECTED COMPRESSOR - The compressor is internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor. DURABLE FINISH - The cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted desert sand finish insure less fading when exposed to sunlight. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Discharge line heat exchanger knockouts are provided, if required. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications. LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise up away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections, a single panel covering the electrical controls and the molex plug in the control box connecting the condenser fan, make for easy servicing of the unit. SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging. U.L. AND C.U.L. LISTED - Approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240. FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

2 Physical and Electrical Data - 1 Phase MODEL 012M M M M X X X X1022 Unit Supply Voltage 208/ Normal Voltage Range 187 to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Compressor Type Rotary Recip Recip Recip Recip Recip Recip Scroll B Rated Load Compressor Amps Locked Rotor Crankcase Heater No No No No No No No No Fan Motor Amps Rated Load Fan Diameter Inches 17-1/2 17-1/2 17-1/2 17-1/ Fan Motor Rated HP 1/12 1/12 1/8 1/8 1/4 1/4 1/4 1/4 Nominal RPM 1,100 1,100 1,075 1,075 1,100 1, Nominal CFM 1,600 1,550 1,750 1,750 2,750 2,750 3,250 3,300 Face Area Sq. Ft Coil Rows Deep Fin / Inches Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 5/8 5/8 5/8 3/4 3/4 3/4 7/8 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot, Oz Operating Weight Lbs Physical and Electrical Data - 3 Phase MODEL AC036X1031 AC048X1031 AC060X1031 AC036X1041 AC048X1041 AC060X1041 Unit Supply Voltage 208 / Normal Voltage Range Minimum Circuit Ampacity Max. Overcurrent Device Amps Compressor Type 3 Recip Recip Scroll B Recip Recip Scroll B Compressor Amps Rated Load Locked Rotor Crankcase Heater No No No No No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/4 1/4 1/4 1/4 1/5 1/4 Fan Motor Nominal RPM 1, , Nominal CFM 2,750 3,250 3,450 2,750 3,250 3,450 Face Area Sq. Ft Coil Rows Deep Fin / Inch Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line OD 3/4 7/8 7/8 3/4 7/8 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot, Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2. Dual element fuses or HACR circuit breaker. 3. All scrolls listed with a superscript B are Bristol scrolls. All scrolls listed with a superscript C are Copeland scrolls. 4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value. 2 Unitary Products Group

3 Additional R-22 Charge / Orifice Size for Various Matched Systems - 1 PHASE ADDITIONAL R-22 CHARGE / ORIFICE SIZE FOR VARIOUS MATCHED SYSTEMS Outdoor Unit 012M M M M X X X X1022 Unit Orifice (s) Factory R-22 Charge, lbs-oz Indoor Coil Coil Orifice 2 System Orifice - Additional Charge, Oz G2FD024(S,H)14/ G2FD030(S,H) G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21/ G1HA024H G1HA036H G1HA036H G1HA048H G1HA060H G1FA/G1UA024S14/ G1FA/G1UA030S G1FA/G1UA036S G1FA/G1UA03617/ G1FA/G1UA048S G1FA/G1UA048S G1FA/G1UA060S G1NA024S17G G1NA030S17H G1NA030S17K G1NA030S21B G1NA030S21M G1NA036S17J G1NA036S21C G1NA048S21D G1NA048S24P G1NA060S24T G1NF024SOF G1NF036SOF G1NF048SOF G1NF060SOF F2RP/F2FP F2RP/F2FP F2RP/F2FP F2RC/F2FC F2RP/F2FP F2RP/F2FP F2FP048N F2FP060N FOOTNOTES: 1. These orifices are packed in the customer packet of each outdoor unit. 2. These orifices are factory mounted in the flow control device of each indoor coil. 3. Systems matched with furnaces or air handlers not equipped with blower-off delays, may require blower Time Delay Kit #6918A5011. PROCEDURES: 1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaportor and for 15 feet of interconnecting line tubing. 2. Verify the orifice size and additional charge required for specific evaportor coil in the system using the above table. 3. Add charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above. 4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaportor + adder for line set. 5. If the orifice in the evaportor was changed, verify the evaportor nameplate has been marked with the correct orifice size. Unitary Products Group 3

4 Additional R-22 Charge / Orifice Size for Various Matched Systems - 3 PHASE ADDITIONAL R-22 CHARGE / ORIFICE SIZE FOR VARIOUS MATCHED SYSTEMS Outdoor Unit AC036X AC048X AC060X Unit Orifice (s) Factory R-22 Charge, lbs-oz Indoor Coil Coil Orifice 2 System Orifice = Additional Charge, Oz G1NA036S17J G1NA036S21C G1NA048S21D G1NA048S24P G1NA060S24T G1FA/G1UA036S17/ G1FA/G1UA048S G1FA/G1UA060S21/ G2FD036(S,H) G2FD036(S,H) G2FD042(S,H)21 78 G2FD048(S,H)21/ G2FD060(S,H) G1NF036SOF G1NF048SOF G1NF060SOF FOOTNOTES: 1. These orifices are packed in the customer packet of each outdoor unit. 2. These orifices are factory mounted in the flow control device of each indoor coil. PROCEDURES: 1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaportor and for 15 feet of interconnecting line tubing. 2. Verify the orifice size and additional charge required for specific evaportor coil in the system using the above table. 3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above. 4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaportor + adder for line set. 5. If the orifice in the evaportor was changed, verify the evaportor nameplate has been marked with the correct orifice size. 4 Unitary Products Group

5 COOLING CAPACITY - With Air Handler Coils AIR HANDLER UNIT MODEL MODEL ELECTRIC 2 HEAT KW COIL 1 MODEL COOLING NET MBH SEER TOTAL SENS. W/O TXV 1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number. 2. Single phase units require single phase 2HK heaters. Three phase units require three phase 2HK heaters. 3. TXV = Use 1TV700 Series Kit. 4. To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC. models. All ratings remain the same. 5. FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D (Blower on Delay) standard. - = Not applicable. W RATED CFM SEER + TXV 3 EER 1 PH 10 SEER AC WITH N1AH / G2FD AC012M1021 N1AHB G2FD024(S,H) AC018M1021 N1AHB G2FD024(S,H) AC024M1021 N1AHB G2FD024(S,H) AC030M1021 N1AHB ,15,18 17 G2FD030(S,H) AC036X1021 N1AHB ,15,18 17 G2FD036(S,H) AC042X1021 N1AHC ,15,18 21 G2FD042(S,H) AC048X1021 N1AHC ,15,18 21 G2FD048(S,H) AC060X1022 N1AHD2006 8,10,15,20,25,30 24 G2FD060(S,H) PH 10 SEER AC WITH N1AH / G2FD AC036X10(31,41) N1AHB ,15 21 G2FD036(S,H) AC036X10(31,41) N1AHB ,15 21 G2FD042(S,H) AC048X10(31,41) N1AHC ,15 21 G2FD048(S,H) AC048X10(31,41) N1AHD ,15,29 24 G2FD048(S,H) AC048X10(31,41) N1AHD ,15,29 24 G2FD048(S,H) AC060X10(31,41) N1AHD ,15,29 24 G2FD060(S,H) PH 10 SEER AC / F2RP / RC / FC 4, 5 AC012M1021 F2RP018 2,5, AC012M1021 M1HC AC018M1021 F2RP/F2FP018 2,5, AC018M1021 F2RP/F2FP024 5,8, AC024M1021 F2RP/F2FP024 5,8, AC024M1021 F2RP/F2FP024 5,8, AC030M1021 F2RP/F2FP030 5,8,10, AC030M1021 F2RP/F2FP036 5,8,10,15, AC036X1021 F2RC/F2FC036 5,8,10, AC036X1021 F2RP/F2FP036 5,8,10,15, AC036X1021 F2RP/F2FP042 5,8,10, AC042X1021 F2FP048 5,8,10,15,20, AC042X1021 F2RP/F2FP042 5,8,10, AC048X1021 F2FP048 5,8,10,15,20, AC048X1021 F2FP060 5,8,10,15,20, AC060X1022 F2FP060 5,8,10,15,20, PH 10 seer AC with F2RP / FP AC036X10(31,41) F2RC/F2FC036 5,8,10, AC048X10(31,41) F2FP048 5,8,10,15,20, AC060X10(31,41) F2FP060 5,8,10,15,20, Rated in accordance with DOE test procedures (Federal Register and ) and ARI Standards 210/240. Cooling MBH based on 80 F entering air temperature, 50% RH, and rated air flow. EER (Energy Efficiency Ratio) is the total cooling output in BTU s at a 95 F outdoor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period. Unitary Products Group 5

6 COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils FURNACE** COOLING COIL UNIT MODEL NET MBH W MODEL RATED CFM AC012M1021 AC018M1021 AC024M1021 AC030M1021 AC036X1021 CFM RANGE (MIN.-MAX.) TOTAL SENS. SEER W/O TXV SEER + TXV 1 14,17 G1FA024S14, G1HD G1NA024S17G ,17 G1UA024S14, ,17 G2FD024(S,H)14, ,17 G1FA024S14, G1HA024H G1HD G1NA024S17G ,17 G1UA024S14, ,17 G2FD024(S,H)14, ,17 G1FA024S14, G1FA036S G1HA024H G1HA036H G1HD G1NA030S17H G1NA030S21B ,17 G1UA024S14, G1UA036S ,17 G2FD024(S,H)14, G1FA030S G1FA036S ,21 G1FA036S17, G1HA036H G1HA036H G1HD G1NA030S17K G1NA030S21M G1UA030S G1UA036S ,21 G1UA036S17, G2FD030(S,H) G2FD035(S,H) G1FA036S ,21 G1FA036S17, G1FA048S ,24 G1FA048S G1HA036H G1HA036H G1HA048H G1HD G1HD G1NA036S17J G1NA036S21C G1UA036S ,21 G1UA036S17, G1UA048S ,24 G1UA048S G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) G2FD046(S,H) EER 6 Unitary Products Group

7 COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils (Continued) FURNACE** COOLING COIL UNIT MODEL NET MBH W MODEL RATED CFM AC036X10(31,41) For Notes See Page 5. AC042X1021 AC042X1031,41 AC048X1021 AC048X10(31,41) CFM RANGE (MIN.-MAX.) TOTAL SENS. SEER W/O TXV SEER + TXV 1 17,21 G1FA036S17, ,24 G1FA048S G1NA036S17J G1NA036S21C ,21 G1UA036S17, ,24 G1UA048S G2FD036(S,H) G2FD036(S,H) G1FA048S ,24 G1FA048S ,24 G1FA060S21, G1HA036H G1HA048H G1HD G1NA036S21C G1NA048S21D G1UA048S ,24 G1UA048S ,24 G1UA060S21, G2FD042(S,H) G2FD046(S,H) ,24 G2FD048(S,H)21, G2FD060(S,H) ,24 G1FA048S ,24 G1FA060S21, G1NA036S21C G1NA048S21D ,24 G1UA048S ,24 G1UA060S21, G2FD042(S,H) G2FD046(S,H) ,24 G2FD048(S,H)21, G1FA048S ,24 G1FA048S ,24 G1FA060S21, G1HA048H G1HA060H G1HD G1HD G1NA048S21D G1UA048S ,24 G1UA048S ,24 G1UA060S21, G2FD046(S,H) ,24 G2FD048(S,H)21, G2FD060(S,H) ,24 G1FA048S G1NA048S21D ,24 G1UA048S ,24 G2FD048(S,H)21, EER Unitary Products Group 7

8 COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils (Continued) FURNACE** COOLING COIL UNIT MODEL NET MBH W MODEL RATED CFM AC060X1022 AC060X10(31,41) CFM RANGE (MIN.-MAX.) TOTAL 21,24 G1FA060S21, G1HA060H G1HD G1NA048S21D G1NA060S24T ,24 G1UA060S21, G2FD060(S,H) G2FD061H ,24 G1FA060S21, G1NA060S24T ,24 G1UA060S21, G2FD060(S,H) TXV = Use 1TV700 Series Kit. * Requires a 2FD Blower Time Delay unless a standard furnace is equipped with one. ** Refer to Quick Selection Chart for specific furnace match-up. COOLING PERFORMANCE MODEL AC012M1021 AC018M1021 AC024M1021 AC030M1021 AC036X1021 AC036X10(31,41) SENS. SEER W/O TXV SEER + TXV 1 SUCT. AIR TEMP ON CONDENSER SUCT. AIR TEMP ON CONDENSER COMPR. 75ºF 95ºF 115ºF MODEL COMPR. 75ºF 95ºF 115ºF TEMP. PSIG MBH KW MBH KW MBH KW TEMP. PSIG MBH KW MBH KW MBH KW AC042X AC048X AC048X10(31,41) AC060X AC060X10(31,41) NOTES: 1. For condensing unit only. Does not include effect of evaporator motor power or heat. 2. Performance based on 15 superheat and 15 sub-cooling at condensing unit. a. Increase capacity 1% for each 2 increase in sub-cooling. b. Decrease capacity 1% for each 2 decrease in sub-cooling. 3. Sub-cooling in excess of 20 may result in excessively high condensing temperature with air on condenser above 115 F. Maximum recommended condensing temperature is 140 F. EER 8 Unitary Products Group

9 A A B C B C 1. Including Fan guard. ACCESSORIES* Refer to Price Manual for specific model numbers. Hard Start Kit - Provides increased starting torque for areas with low voltage. Compressor Blanket - Designed to further reduce the normal compressor operating sound. Refer to price pages for specific match-ups. Off Cycle Timer Delay - Provides a 5-minute off cycle to prevent rapid recycling of the compressor. Room Thermostats - A wide selection of compatible thermosets are available to provide optimum performance and features for any installation. 1 Heat Stage only, manual, mechanical thermostat. Add subbase for 1H/1C. 1H/1C, manual change-over electronic non-programmable thermostat. 1H/1C, auto/manual changeover, electronic programmable, deluxe 7-day, thermostat. 1H/1C, auto/manual changeover, electronic programmable. * For the most current accessory information, refer to the price book or consult factory. SOUND POWER RATINGS* DIMENSIONS - 1 Phase Unit Model Dimensions (Inches) Refrigerant Connection Service Valve Size A 1 B C Liquid Vapor /4 21-3/ /4 21-3/ /4 21-3/ /4 21-3/ /8 3/4 2 3/4 7/8 UNIT MODEL (dba) *Rated in accordance with ARI Standards. 1. Including Fan guard. 2. Reducer fitting required for 5/8 line set. DIMENSIONS - 3 Phase Unit Model Dimensions (Inches) Refrigerant Connection Service Valve Size A 1 B C Liquid Vapor /8 3/ /8 7/ /8 7/8 Unitary Products Group 9

10 TYPICAL INSTALLATION - AC012M1021 THRU 030 AND AC036X1021 THRU CLEARANCE AROUND PERIMETER 1 TO 2.5 TON, 10 SEER ( M SERIES ONLY) 60 OVERHEAD CLEARANCE MINIMUM 18 SERVICE ACCESS CLEARANCE ON ONE SIDE WEATHERPROOF DISCONNECT SWITCH THERMOSTAT TO FURNACE OR AIR HANDLER TERMINAL BLOCK NEC CLASS 1 WIRING NEC CLASS 2 WIRING 10 CLEARANCE COIL AREA 3 TO 5 TONS, 10 SEER TO INDOOR COIL NOTE: ALL OUTDOOR WIRING MUST BE WEATHERPROOF. SEAL OPENING(S) WITH PERMAGUM OR EQUIVALENT CONTROL ACCESS PANEL TYPICAL FIELD WIRING - 1 PHASE APPLICATION ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES POWER WIRING 208/ VOLT CONTROL WIRING MINIMUM 18 GA. WIRE (NEC CLASS 2) POWER WIRING CONTROL WIRING FACTORY WIRING * TERMINAL W IS ONLY REQUIRED ON SYSTEMS WITH HEAT. FURNACE OR AIR HANDLER TERMINAL BLOCK C Y R G W GND. LUG CONTACTOR TERMINALS COIL Y R G W * CONDENSING UNIT ALL OUTDOOR WIRING MUST BE WEATHERPROOF. ROOM THERMOSTAT USE COPPER CONDUCTORS ONLY. TYPICAL FIELD WIRING - 3 PHASE APPLICATION ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES POWER WIRING 208/ VOLT CONTROL WIRING MINIMUM 18 GA. WIRE (NEC CLASS 2) POWER WIRING CONTROL WIRING FACTORY WIRING FURNACE OR AIR HANDLER TERMINAL BLOCK GND. LUG CONTACTOR TERMINALS COIL * TERMINAL W IS ONLY REQUIRED ON SYSTEMS WITH HEAT. C Y R G W * Y R G W CONDENSING UNIT ROOM THERMOSTAT ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY. 10 Unitary Products Group

11 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC012M1021 G1NA024S17G ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW N1AHB0806 G2FD024(S,H) F2RP M1HC G1FA024S14, G1HD G1UA024S14, G2FD024(S,H)14, Unitary Products Group 11

12 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC018M1021 G1NA024S17G ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW N1AHB0806 G2FD024(S,H) F2RP/F2FP F2RP/F2FP G1FA024S14, G1HD G1NA024S17G G1UA024S14, G2FD024(S,H)14, Unitary Products Group

13 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC024M1021 G1NA030S17H ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW N1AHB0806 G2FD024(S,H) F2RP/F2FP F2RP/F2FP G1FA024S14, G1FA036S G1HD G1NA030S17H G1NA030S21B G1UA024S14, G1UA036S G2FD024(S,H)14, Unitary Products Group 13

14 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC030M1021 G1NA030S17K ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW N1AHB1206 G2FD030(S,H) F2RP/F2FP F2RP/F2FP G1FA030S G1FA036S G1FA036S17, G1HD G1NA030S21M G1UA030S G1UA036S G1UA036S17, G2FD030(S,H) G2FD035(S,H) Unitary Products Group

15 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC036X1021, AC036X10(31,41) G1FA036S17,21 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. 1 Phase 3 Phase Air Handler Coil T.C. S.C. KW Air Handler Coil T.C. S.C. KW N1AHB1206 G2FD036(S,H) N1AHB1246 G2FD036(S,H) N1AHB1206 G2FD046(S,H) N1AHB1246 G2FD046(S,H) F2RC/F2FC F2RC/F2FC F2RP/F2FP G1FA048S F2RP/F2FP G1NA036S17J G1FA036S G1NA036S21C G1FA048S G1UA036S17, G1FA048S G1UA048S G1HD G2FD036(S,H) G2FD046(S,H) G2FD036(S,H) G1HD G1NA036S17J G1NA036S21C G1UA036S G1UA036S17, G1UA048S G1UA048S G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) Unitary Products Group 15

16 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC042X1021, AC042X10(31,41) G1FA048S21 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. 1 Phase 3 Phase Air Handler Coil T.C. S.C. KW Air Handler Coil T.C. S.C. KW N1AHC1606 G2FD042(S,H) N1AHC1646 G2FD042(S,H) N1AHC1606 G2FD048(S,H) N1AHC1646 G2FD048(S,H) F2RP/F2FP F2RP/F2FP F2FP F2FP G1FA048S G1FA060S21, G1FA060S21, G1NA036S21C G1HD G1NA048S21D G1NA036S21C G1UA048S G1NA048S21D G1UA060S21, G1UA048S G2FD042(S,H) G1UA048S G2FD046(S,H) G1UA060S21, G2FD048(S,H)21, G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21, G2FD060(S,H) Unitary Products Group

17 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC048X1021, AC048X10(31,41) G1FA048S21 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. 1 Phase 3 Phase Air Handler Coil T.C. S.C. KW Air Handler Coil T.C. S.C. KW N1AHC1606 G2FD048(S,H) N1AHC1646 G2FD048(S,H) N1AHD2006 G2FD060(S,H) N1AHD2046 G2FD048(S,H) F2FP N1AHD2046 G2FD060(S,H) F2FP F2FP G1FA048S G1FA048S G1FA060S21, G1NA048S21D G1UA048S G1UA048S G1HD G2FD048(S,H)21, G1HD Unitary Products Group 17

18 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC060X1022 G1FA060S21,24 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW N1AHD2006 G2FD060(S,H) F2FP G1HD G1NA048S21D G1NA060S24T G1UA060S21, G2FD060(S,H) G2FD061H Unitary Products Group

19 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER ENTERING AIR TEMPERATURE AC060X10(31,41) G2FD060(S,H)24A ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW N1AHD2046 G2FD060(S,H) F2FP G1FA060S21, G1NA060S24T G1UA060S21, Unitary Products Group 19

20 MATCHING INDOOR COMPONENTS ADD-ON COILS - FOR FURNACE APPLICATIONS G1UA 1/2 CASED UPFLOW G1HD HORIZONTAL DUCT G1NA UNCASED UPFLOW G1FA FULL CASED UPFLOW G2FD* MULTI-POSITION (UPFLOW, HORIZONTAL AND DOWNFLOW) * Available with factory installed horizontal drain pan. AIR HANDLERS - FOR NON-FURNACE APPLICATIONS N-AH OR N-VS MODULAR BLOWER (UPFLOW, HORIZONTAL AND DOWNFLOW) G+FD COIL F+RC / F+FC OR F+RC / F+FP FAN COIL UNITS (UPFLOW, HORIZONTAL) Subject to change without notice. Printed in U.S.A Rev. E (0405) Copyright by York International Corp All rights reserved. Supersedes: Rev. D (0604) Unitary 5005 Norman Product York OK Group Drive 73069