1/8. Field settings table. Applicable indoor units. GSQH10S18AA9W ThermaliaC12 Notes - GSQH10S18AA9W / ThermaliaC12 4P C

Transcription

1 1/8 Applicable indoor units *GSQH1S18AA9W ThermaliaC12* Notes - *GSQH1S18AA9W / ThermaliaC12* 4P C

2 2/8

3 3/8 User settings Preset values Room temperature Comfort (heating) R/W [3-7]~[3-6], step: A C Eco (heating) R/W [3-7]~[3-6], step: A C LWT main [8-9] Comfort (heating) R/W [9-1]~[9-], step: 1 C 55 C [8-A] Eco (heating) R/W [9-1]~[9-], step: 1 C Comfort (heating) R/W -1~1, step: 1 C Eco (heating) R/W -1~1, step: 1 C -2 C Tank temperature [6-A] Storage comfort R/W 3~[6-E] C, step: 1 C [6-B] Storage eco R/W 3~min(5, [6-E]) C, step: 1 C [6-C] Reheat R/W 3~min(5, [6-E]) C, step: 1 C Quiet level : Level 1 (*) 1: Level 2 2: Level 3 Installer settings System layout Standard A [E-] Unit type R/O 5: Ground source A [E-1] Compressor type R/O 1: 16 A [E-2] Indoor software type R/O 1: Type 2 A [5-D] BUH type R/O 4: 3PN,(1/2) A [D-1] Preferential kwh rate : No 1: Active open 2: Active closed A [C-7] Unit control method : LWT control 1: Ext RT control 2: RT control A [7-2] Number of LWT zones : 1 LWT zone 1: 2 LWT zones A [F-D] Pump operation mode : Continuous 1: Sample (only possible if [C-7] = ) 2: Request (only possible if [C-7] ) A.2.1.A [E-4] Power saving possible : No A.2.1.B User interface location : At unit 1: In room Options A [C-5] Contact type main : Thermo ON/OFF 2: C/H request A [C-6] Contact type add. : Thermo ON/OFF 2: C/H request A [C-2] Digital I/O PCB Ext. backup heat src : No 1: Bivalent A [D-7] Digital I/O PCB Solar kit : No (*) A [C-9] Digital I/O PCB Alarm output : Normally open 1: Normally closed A [D-4] Demand PCB : No 1: Power consumption control A [D-8] External kwh meter 1 (No): NOT installed 1: Installed (.1 pulse/kwh) 2: Installed (1 pulse/kwh) 3: Installed (1 pulse/kwh) 4: Installed (1 pulse/kwh) 5: Installed (1 pulse/kwh) A [D-9] External kwh meter 2 (No): NOT installed 1: Installed (.1 pulse/kwh) 2: Installed (1 pulse/kwh) 3: Installed (1 pulse/kwh) 4: Installed (1 pulse/kwh) 5: Installed (1 pulse/kwh) A.2.2.A [D-2] DHW pump : No 1: Secondary rtrn ([E-6]=1) 2: Disinf. Shunt ([E-6]=1) A.2.2.B [C-8] External sensor : No 1: Outdoor sensor (**) 2: Room sensor Capacities A [6-3] BUH: step 1 ~1kW, step:,2kw 3kW A [6-4] BUH: step 2 ~1kW, step:,2kw 3kW Space operation LWT settings Main A LWT setpoint mode : Fixed 1: Weather dep. 2: Fixed / scheduled 3: WD / scheduled A [9-1] Temperature range Minimum temp (heating) 5~37 C, step: 1 C 24 C A [9-] Temperature range Maximum temp (heating) R/W 37~65 C, step: 1 C 65 C A [1-] Set weather-dependent heating Low ambient temp. for LWT main zone heating R/W -2~5 C, step: 1 C -2 A [1-1] Set weather-dependent heating High ambient temp. for LWT main zone heating ~2, step: 1 C A [1-2] Set weather-dependent heating Leaving water value for low ambient temp. for R/W [9-1]~[9-], step: 1 C LWT main zone heating 6 A [1-3] Set weather-dependent heating Leaving water value for high ambient temp. for R/W [9-1]~min(45,[9-]), step: 1 C LWT main zone heating 25 C (*) This setting is not applicable for this unit. Do not change the. *GSQH1S18AA9W / ThermaliaC12* 4P C

4 4/8 A [8-5] Modulated LWT : No A [F-B] Shut-off valve Thermo On/OFF : No A [9-B] Emitter type : Quick 1: Slow Additional A LWT setpoint mode : Fixed 1: Weather dep. 2: Fixed / scheduled 3: WD / scheduled A [9-5] Temperature range Minimum temp (heating) 5~37 C, step: 1 C 24 C A [9-6] Temperature range Maximum temp (heating) R/W 37~65 C, step: 1 C 65 C A [-] Set weather-dependent heating Leaving water value for high ambient temp. for R/W [9-5]~min(45,[9-6]) C, step: 1 C LWT add zone heating 25 C A [-1] Set weather-dependent heating Leaving water value for low ambient temp. for R/W [9-5]~[9-6] C, step: 1 C LWT add zone heating 6 A [-2] Set weather-dependent heating High ambient temp. for LWT add zone heating ~2, step: 1 C A [-3] Set weather-dependent heating Low ambient temp. for LWT add zone heating R/W -2~5 C, step: 1 C -2 Delta T emitter A [9-9] Delta T emitter Heating R/W 3~1, step: 1 C 8 C Room thermostat A [3-7] Room temp. range Minimum temp (heating) 2~18 C, step: A C A [3-6] Room temp. range Maximum temp (heating) 8~3, step: A A [2-A] Room temp. offset R/W -5~5 C, step:,5 C A [2-9] Ext. room sensor offset R/W -5~5 C, step:,5 C A Room temp. step : 1 C 1:,5 C Operation range A [4-2] Space heating OFF temp 4~35 C, step: 1 C 35 C Domestic hot water (DHW) Type A.4.1 [6-D] : Reheat only 1: Reheat + sched. 2: Scheduled only Setpoint readout A Setpoint readout type : Temperature 1: Graphical A Conversion persons 1 person R/W 3~8, step: 1 C 42 C A Conversion persons 2 persons ~2, step: 1 C 6 C A Conversion persons 3 persons ~2, step: 1 C A Conversion persons 4 persons ~2, step: 1 C 17 C A Conversion persons 5 persons ~2, step: 1 C 1 C A Conversion persons 6 persons ~2, step: 1 C 1 C Disinfection A [2-1] Disinfection : No A [2-] Operation day : Each day 1: Monday 2: Tuesday 3: Wednesday 4: Thursday 5: Friday 6: Saturday 7: Sunday A [2-2] Start time ~23 hour, step: 1 hour 23 A [2-3] Temperature target R/W 6 A [2-4] Duration R/W 4~6 min, step: 5 min 6 min Maximum setpoint A.4.5 [6-E] R/W 4~6, step: 1 C 6 SP mode A.4.6 SP mode : Fixed 1: Weather dep. Weather dependant curve A.4.7 [-B] Weather-dependent curve DHW setpoint for high ambient temp. for DHW R/W 35~[6-E] C, step: 1 C A.4.7 [-C] Weather-dependent curve DHW setpoint for low ambient temp. for DHW R/W 45~[6-E] C, step: 1 C 6 A.4.7 [-D] Weather-dependent curve High ambient temp. for DHW ~2, step: 1 C A.4.7 [-E] Weather-dependent curve Low ambient temp. for DHW R/W -2~5 C, step: 1 C -2 Heat sources Backup heater A [4-] Operation mode : Limit 1: Enable 2: Only DHW A Auto emergency operation : Manual 1: Automatic A [4-7] Enable BUH step 2 : No A [5-1] Equilibrium temp. R/W -15~35 C, step: 1 C System operation 4P C (*) This setting is not applicable for this unit. Do not change the. *GSQH1S18AA9W / ThermaliaC12*

5 5/8 Auto restart A.6.1 [3-] Is auto restart of the unit allowed? : No Preferential kwh rate A [D-] Allowed heaters : None A [D-5] Forced pump OFF : Forced off 1: As normal Averaging time A.6.4 [1-A] : No averaging 1: 12 hours 2: 24 hours 3: 48 hours 4: 72 hours Ext amb. sensor offset A.6.5 [2-B] R/W -5~5 C, step:,5 C Forced defrost A.6.6 Are you sure you want to activate the forced defrost function? R/W (*) Brine freezeup temperature A.6.9 [A-4] : 1: -2 C 2: -4 C 3: -6 C 4: -8 C 5: -1 6: -12 C 7: -14 C Boiler efficiency A.6.A [7-5] : Very high (*) 1: High 2: Medium 3: Low 4: Very low Overview settings A.8 [-] Leaving water value for high ambient temp. for LWT add zone heating R/W [9-5]~min(45,[9-6]) C, step: 1 C 25 C A.8 [-1] Leaving water value for low ambient temp. for LWT add zone heating R/W [9-5]~[9-6] C, step: 1 C 6 A.8 [-2] High ambient temp. for LWT add zone heating ~2, step: 1 C A.8 [-3] Low ambient temp. for LWT add zone heating R/W -2~5 C, step: 1 C -2 A.8 [-4] -- R/W 8 A.8 [-5] -- 2 A.8 [-6] -- R/W 35 A.8 [-7] -- R/W 2 A.8 [-B] Leaving water value for high ambient temp. for DHW R/W 35~[6-E] C, step: 1 C A.8 [-C] Leaving water value for low ambient temp. for DHW R/W 45~[6-E] C, step: 1 C 6 A.8 [-D] High ambient temp. for DHW ~2, step: 1 C A.8 [-E] Low ambient temp. for DHW R/W -2~5 C, step: 1 C -2 A.8 [1-] Low ambient temp. for LWT main zone heating R/W -2~5 C, step: 1 C -2 A.8 [1-1] High ambient temp. for LWT main zone heating ~2, step: 1 C A.8 [1-2] Leaving water value for low ambient temp. for LWT main zone heating R/W [9-1]~[9-], step: 1 C 6 A.8 [1-3] Leaving water value for high ambient temp. for LWT main zone heating R/W [9-1]~min(45,[9-]), step: 1 C 25 C A.8 [1-4] -- A.8 [1-5] -- A.8 [1-6] -- R/W 2 A.8 [1-7] -- R/W 35 A.8 [1-8] -- R/W 22 A.8 [1-9] -- 8 A.8 [1-A] What is the averaging time for the outdoor temp? : No averaging 1: 12 hours 2: 24 hours 3: 48 hours 4: 72 hours A.8 [2-] When should the disinfection function be executed? : Each day 1: Monday 2: Tuesday 3: Wednesday 4: Thursday 5: Friday 6: Saturday 7: Sunday A.8 [2-1] Should the disinfection function be executed? : No A.8 [2-2] When should the disinfection function start? ~23 hour, step: 1 hour 23 A.8 [2-3] What is the disinfection target temperature? R/W 6 A.8 [2-4] How long must the tank temperature be maintained? R/W 4~6 min, step: 5 min 6 min A.8 [2-5] Room antifrost temperature R/W 4~16 C, step: 1 C 12 C A.8 [2-6] Room frost protection : Disabled 1: Enabled A.8 [2-9] Adjust the offset on the measured room temperature R/W -5~5 C, step:,5 C A.8 [2-A] Adjust the offset on the measured room temperature R/W -5~5 C, step:,5 C A.8 [2-B] What is the required offset on the measured outdoor temp.? R/W -5~5 C, step:,5 C A.8 [3-] Is auto restart of the unit allowed? : No A.8 [3-1] -- A.8 [3-2] -- A.8 [3-3] -- R/W 4 (*) This setting is not applicable for this unit. Do not change the. *GSQH1S18AA9W / ThermaliaC12* 4P C

6 6/8 A.8 [3-4] -- R/W 2 A.8 [3-5] -- A.8 [3-6] What is the maximum desired room temperature in heating? 8~3, step: A A.8 [3-7] What is the mimimum desired room temperature in heating? 2~18 C, step: A C A.8 [3-8] -- R/W 35 A.8 [3-9] -- 5 A.8 [4-] What is the BUH operation mode? : Limit 1: Enable 2: Only DHW A.8 [4-1] -- A.8 [4-2] Below which outdoor temperature is heating allowed? 4~35 C, step: 1 C 35 C A.8 [4-3] -- R/W 3 A.8 [4-4] -- R/W 2 A.8 [4-5] -- A.8 [4-6] -- A.8 [4-7] Enable the second step of the backup heater? : No A.8 [4-8] Which power limitation mode is required on the system? : No limitation 1: Continuous 2: Digital inputs A.8 [4-9] Which power limitation type is required? : Current 1: Power A.8 [4-B] -- A.8 [4-D] -- R/W 3 A.8 [5-] Is backup heater or boiler operation allowed above equilibrium temperature during space heating operation? : Allowed 1: Not allowed A.8 [5-1] What is the equilibrium temperature for the building? R/W -15~35 C, step: 1 C A.8 [5-2] -- A.8 [5-3] -- A.8 [5-4] -- A.8 [5-5] What is the requested limit for DI1? ~5 A, step: 1 A 5 A A.8 [5-6] What is the requested limit for DI2? ~5 A, step: 1 A 5 A A.8 [5-7] What is the requested limit for DI3? ~5 A, step: 1 A 5 A A.8 [5-8] What is the requested limit for DI4? ~5 A, step: 1 A 5 A A.8 [5-9] What is the requested limit for DI1? ~2 kw, step:,5 kw 2 kw A.8 [5-A] What is the requested limit for DI2? ~2 kw, step:,5 kw 2 kw A.8 [5-B] What is the requested limit for DI3? ~2 kw, step:,5 kw 2 kw A.8 [5-C] What is the requested limit for DI4? ~2 kw, step:,5 kw 2 kw A.8 [5-D] What type of backup heater installation is used? R/O 4: 3PN,(1/2) A.8 [5-E] -- A.8 [6-] The temperature difference determining the heat pump ON temperature. R/W 2~2, step: 1 C 2 C A.8 [6-1] The temperature difference determining the heat pump OFF temperature. ~1, step: 1 C 2 C A.8 [6-2] -- A.8 [6-3] What is the capacity of the backup heater step 1? ~1kW, step:,2kw 3kW A.8 [6-4] What is the capacity of the backup heater step 2? ~1kW, step:,2kw 3kW A.8 [6-5] -- A.8 [6-6] -- A.8 [6-7] -- A.8 [6-8] Reheat hysteresis R/W 2~2, step: 1 C 1 A.8 [6-9] -- A.8 [6-A] What is the desired comfort storage temperature? R/W 3~[6-E] C, step: 1 C 6 A.8 [6-B] What is the desired eco storage temperature? R/W 3~min(5, [6-E]) C, step: 1 C A.8 [6-C] What is the desired reheat temperature? R/W 3~min(5, [6-E]) C, step: 1 C A.8 [6-D] What is the desired setpoint mode in DHW? : Reheat only 1: Reheat + sched. 2: Scheduled only A.8 [6-E] What is the maximum tank temperature setpoint? R/W 4~6, step: 1 C 6 A.8 [7-] -- A.8 [7-1] -- R/W 2 A.8 [7-2] How many leaving water temperature zones are there? : 1 LWT zone 1: 2 LWT zones A.8 [7-3] PE factor ~6, step:,1 2,5 A.8 [7-4] -- A.8 [7-5] Boiler efficiency : Very high (*) 1: High 2: Medium 3: Low 4: Very low A.8 [8-] Minimum running time for domestic hot water operation. ~2 min, step: 1 min 5 min A.8 [8-1] Maximum running time for domestic hot water operation. R/W 5~95 min, step: 5 min 3 min A.8 [8-2] Anti-recycling time. ~1 hour, step:,5 hour,5 hour A.8 [8-3] -- R/W 5 A.8 [8-4] Additional running time for the maximum running time. ~95 min, step: 5 min 95 min A.8 [8-5] Allow modulation of the LWT to control the room? : No 4P C (*) This setting is not applicable for this unit. Do not change the. *GSQH1S18AA9W / ThermaliaC12*

7 7/8 A.8 [8-6] Leaving water temperature maximum modulation. ~5 C, step: 1 C 3 C A.8 [8-7] -- 8 A.8 [8-8] -- R/W 2 A.8 [8-9] What is the desired comfort main LWT in heating? R/W [9-1]~[9-], step: 1 C 55 C A.8 [8-A] What is the desired eco main LWT in heating? R/W [9-1]~[9-], step: 1 C A.8 [8-B] -- 3 A.8 [8-C] -- A.8 [8-D] -- A.8 [9-] What is the maximum desired LWT for main zone in heating? R/W 37~65 C, step: 1 C 65 C A.8 [9-1] What is the mimimum desired LWT for main zone in heating? 5~37 C, step: 1 C 24 C A.8 [9-2] -- R/W 22 A.8 [9-3] -- R/W 5 A.8 [9-4] -- A.8 [9-5] What is the mimimum desired LWT for add. zone in heating? 5~37 C, step: 1 C 24 C A.8 [9-6] What is the maximum desired LWT for add. zone in heating? R/W 37~65 C, step: 1 C 65 C A.8 [9-7] -- R/W 5 A.8 [9-8] -- R/W 22 A.8 [9-9] What is the desired delta T in heating? R/W 3~1, step: 1 C 8 C A.8 [9-A] -- R/W 5 A.8 [9-B] What emitter type is connected to the main LWT zone? : Quick 1: Slow A.8 [9-C] Room temperature hysteresis. ~6 C, step:,5 C 1 C A.8 [A-] -- A.8 [A-1] -- A.8 [A-2] -- A.8 [A-3] Maximum heating frequency : 148Hz 1: 193Hz A.8 [A-4] Brine freezup temperature : 1: -2 C 2: -4 C 3: -6 C 4: -8 C 5: -1 6: -12 C 7: -14 C A.8 [B-] -- A.8 [B-1] -- A.8 [B-2] -- A.8 [B-3] -- A.8 [B-4] -- A.8 [C-] -- R/O 1 A.8 [C-1] -- A.8 [C-2] Is an external backup heat source connected? : No 1: Bivalent A.8 [C-3] Bivalent activation temperature. R/W -25~25 C, step: 1 C A.8 [C-4] Bivalent hysteresis temperature. R/W 2~1, step: 1 C 3 C A.8 [C-5] What is the thermo request contact type for the main zone? : Thermo ON/OFF 2: C/H request A.8 [C-6] What is the thermo request contact type for the add. zone? : Thermo ON/OFF 2: C/H request A.8 [C-7] What is the unit control method in space operation? : LWT control 1: Ext RT control 2: RT control A.8 [C-8] Which type of external sensor is installed? : No 1: Outdoor sensor (**) 2: Room sensor A.8 [C-9] What is the required alarm output contact type? : Normally open 1: Normally closed A.8 [C-A] -- A.8 [C-C] -- A.8 [C-D] -- A.8 [C-E] -- A.8 [D-] Which heaters are permitted if prefer. kwh rate PS is cut? : None A.8 [D-1] Contact type of preferential kwh rate PS installation? : No 1: Active open 2: Active closed A.8 [D-2] Which type of DHW pump is installed? : No 1: Secondary rtrn ([E-6]=1) 2: Disinf. Shunt ([E-6]=1) A.8 [D-3] Leaving water temperature compensation around. : Disabled 1: Enabled, shift 2 C (from -2 to 2 C) 2: Enabled, shift 4 C (from -2 to 2 C) 3: Enabled, shift 2 C (from -4 to 4 C) 4: Enabled, shift 4 C (from -4 to 4 C) A.8 [D-4] Is a demand PCB connected? : No 1: Power consumption control A.8 [D-5] Is the pump allowed to run if prefer. kwh rate PS is cut? : Forced off 1: As normal A.8 [D-7] Is a solar kit connected? : No (*) A.8 [D-8] Is an external kwh meter used for power measurement? (No): NOT installed 1: Installed (.1 pulse/kwh) 2: Installed (1 pulse/kwh) 3: Installed (1 pulse/kwh) 4: Installed (1 pulse/kwh) 5: Installed (1 pulse/kwh) A.8 [D-9] Is an external kwh meter used for power measurement? (No): NOT installed 1: Installed (.1 pulse/kwh) 2: Installed (1 pulse/kwh) 3: Installed (1 pulse/kwh) 4: Installed (1 pulse/kwh) 5: Installed (1 pulse/kwh) A.8 [D-A] -- (*) This setting is not applicable for this unit. Do not change the. *GSQH1S18AA9W / ThermaliaC12* 4P C

8 8/8 A.8 [D-B] -- R/O 2 A.8 [D-C] -- A.8 [D-D] -- A.8 [D-E] -- A.8 [E-] Which type of unit is installed? R/O 5: Ground source A.8 [E-1] Which compressor type is installed in unit? R/O 1: 16 A.8 [E-2] Which Indoor software type is installed in unit? R/O 1: Type 2 A.8 [E-3] -- R/O 2 A.8 [E-4] Is the power saving function available on the outdoor unit? : No A.8 [E-5] -- A.8 [E-6] -- R/O 1 A.8 [E-7] -- R/O 1 A.8 [E-8] -- A.8 [E-9] -- A.8 [E-A] -- A.8 [F-] Pump operation allowed outside range. : Disabled 1: Enabled A.8 [F-1] -- R/W 2 A.8 [F-2] -- R/W 3 A.8 [F-3] -- R/O 5 A.8 [F-4] -- A.8 [F-5] -- A.8 [F-6] -- A.8 [F-9] Pump operation during flow abnormality. : Disabled 1: Enabled A.8 [F-A] -- A.8 [F-B] Close shut-off valve during thermo OFF? : No A.8 [F-C] -- A.8 [F-D] What is the pump operation mode? : Continuous 1: Sample (only possible if [C-7] = ) 2: Request (only possible if [C-7] ) 4P C (*) This setting is not applicable for this unit. Do not change the. *GSQH1S18AA9W / ThermaliaC12*