SILENCE THIN DC-INVERTER Fan coil GB 01. Air conditioning. Ideas to install

Transcription

1 SILENCE THIN DC-INVERTER Fan coil GB 01 ir conditioning Ideas to install

2 Silence... to listen to Cooling, dehumidification and heating systems have finally found a valid and innovative solution with the use of the single device SILENCE THIN which is able to create and maintain the conditions of total comfort in every season thanks to its sophisticated and precise control. SILENCE THIN is equipped with the very new technology DC-INVERTER high efficiency permanent magnet motor, power and speed adjusted by means of an electronic device in pulse modulation PWM (Pulse With Modulation), which allows a significant reduction of vibration and noise. SILENCE THIN range models are available with or without cabinet, for wall or ceiling installations. ll EMMETI fan coils are designed to reduce as much as possible the noise level and to allow an easy and quick installation.

3 The range ETM models with cover cabinet Fan coils for wall/floor or horizontal ceiling installation. The delicate and balanced design and 130 mm reduced depth make it perfectly suitable to every kind of environment. 130 mm ETI built-in models Fan coils for horizontal or vertical installation. ll ETM and ETI versions are standard equipped with a 3-way valve with calibrated diversion by-pass actuated by normally closed 2-point electrothermal head (ON / OFF 230V~). Installation types Version ETM - Wall / Floor ETM - Ceiling ETI - Vertical / horizontal BSE UTO TERMINL BLOCK EVOLUT

4 ETM models ( BSE version) Fan coil with cover cabinet for wall / floor installation, featuring SMRT TOUCH electronic control to control the room temperature and set the fan speed with UTO function (adjustment of speed in steps), ON/OFF function, cooling / heating. Super Silent function for the operation at the minimum fan cooling speed and only in heating radiant mode (fan off, electrovalve open). UTO Wall / Floor ETM models ( UTO version) This configuration, compared to the previous BSIC version, features two independent clean contacts for the activation of a chiller and a boiler and a presence input. In UTO mode the fan adjustement is linear (not in steps). On the circuit board of the control, there are two dip-switches (microswitches) for the configuration of the operation of the device in function of the requirements. The first microswitch changes the operating logic in night heating mode: when ON, ventilation is inhibited and the machine is therefore able to heat the rooms by radiation and natural convection, as occurs in traditional radiators; when OFF fan operates normally. With the second microswitch: when ON, continuous ventilation at minimum speed is enabled, in cooling only, even after the set point has been reached, in order to allow a more regular operation of the temperature probe and avoid air stratification. when OFF, the function is cycled (2 minutes ON, 10 minutes OFF). Wall / Floor UTO ETM models ( TERMINL BLOCK version) Fan coil with cover cabinet for wall / floor or ceiling installation disposed to be connected with electronic control panel (TE-15) or digital control panel (TD-15). Condensation coollection trays for ceiling installation included. Wall / Floor Ceiling TE-15 TD-15

5 ETI models ( TERMINL BLOCK version) Built-in fan coil for horizontal or vertical installation, disposed to be connected with electronic control panel (TE-15) or digital control panel (TD-15). Vertical Horizontal TE-15 TD-15 ETM and ETI models EVOLUT version Fan coils for wall, floor or ceiling installation, (according to the model) to be combined to a wall-mounted CRB-DCT (mandatory accessory). ETI models, in the case of ceiling installation, must be completed with BRC condensation collection trays. ETM and ETI models EVOLUT version, have the same settings of ETM models UTO version. single CRB-DCT command can be connected to up to 30 temperature controllers. The most common application is a big room where a single CRB-DCT thermostat can control several terminals electrically connected to another. The temperature controller controls the electric valve of the supply circuit of the heat exchanger and the fan speed. Example of single unit management with a single wall-mounted remote control CRB-DCT BUS / / / / UTO CRB-DCT Example of multi-unit management with a single wall-mounted remote control CRB-DCT BUS / / / / UTO CRB-DCT

6 Technical data Models u.m Heating capacity (1) kw (max) 1,89 3,99 5,47 6,98 Water flow (1) l/h Loss of charge (1) kpa 6,7 7,6 16,1 14 Heating capacity (1) * kw (max) 0,322 0,379 0,447 0,563 Heating capacity (2) kw (max) 1,09 2,35 3,19 4,1 Water flow (2) l/h Loss of charge (2) kpa 5,7 6,6 16,3 14 Refrigerating capacity (3) kw (max) 0,83 1,76 2,65 3,34 Refrigerating cap. sensible (3) kw (max) 0,62 1,27 1,96 2,65 Water flow (3) l/h Loss of charge (3) kpa 7,2 8,4 22,5 18,6 ir flow (6) m 3 /h (max) m 3 /h (med) m 3 /h (min) Loss of charge Pa Sound pressure (4) db() (max) 39,4 40,2 42,2 42,5 db() (med) 33,2 34,1 34,4 35 db() (min) 24,2 25,3 25,6 26,3 Fan number n Max power input fan motor W 11,9 17,6 19,8 26,5 Max current absorbed 0,11 0,16 0,18 0,26 Power supply V~/Ph/Hz 230/1/50 230/1/50 230/1/50 230/1/50 Connection (5) 3/4 Eurocone 3/4 Eurocone 3/4 Eurocone 3/4 Eurocone Water quantity coil l 0,47 0,8 1,13 1,46 Maximum operating pressure bar Connection dry tube mm Ø 14 Ø 14 Ø 14 Ø 14 (1) Heating: Room air temperature 20 C - Water inlet temperature 70 C Water Dt 10 C - Maximum fan speed (2) Heating: Room air temperature 20 C - Water inlet temperature 50 C Water flow rate same as in cooling operation - Maximum fan speed (UNI EN 1397) (3) Cooling: Room air temperature 27 C d.b., 19 C w.b. - Water inlet temperature 7 C Water Dt 5 C - Maximum fan speed (4) Sound pressure: Measured in semianechoic room (ISO 779) (5) Connection exchange left standard (6) ir flow rate with clean filters. * Values referred to the conditions (1) but with fan off (70 C) Note: If fan coil is watched frontally, standard plumbing fittings will be to the left and the control is placed in the opposite side of the fittings. MX water inlet temperature 80 C, MIN temp. 4 C.

7 Weight and dimensions ETM models L P H Connections from wall Connections from floor Model u.m Dimensions LxHxPx mm 735x579x131x x579x131x x579x131x x579x131x1105 Net weight kg ETI models L P H Model u.m Dimensions LxHxP mm 525x576x x576x x576x126 Net weight kg ccessories UTO CRB-DCT SMRT TOUCH wall-mounted electronic control panel CRB-DCT with room temperature probe and simultaneous transmission of commands (Broadcast), for EVOLUT version TE-15 Thermostat with cooling/off/heating switch and fan speed slide selector. It can be either controlled by thermostat or always running. Facility for external temperature probe and for a bimetal thermostat for the cutoff thermostat function. TD-15 Digital configurable thermostat, with LCD display, for automatic or manual fan speed selection. Manual, automatic or centralised heating/cooling. Special functions: Economy, Dirty Filter Warning, Window contact. Suitable for remote sensor and supply water pipe sensor (STB).

8 TM Water low temperature thermostat compatible with TE-15 control STB Remote probe air/minimum temperature compatible with TE-15 and TD-15 controls CP2 Pair of attractive feet for wall fixing PP2 Pair of attractive feet for floor installation BRC Condensation collecting basin for ETM Evoluta version ceiling model installation CT Telescopic air flow channel G ir intake grille DTT 3-4 3/4 Eurocone adapter pair kit - Flat seal CF Box with front air output C90 90 elbow channel BM ir flow inlet DIST 3-4 3/4 Eurocone spacer kit for installation with wall-mounted hydraulic connections PE2 ttractive box cover panel R ir intake fitting CCM-DC Motor connection cable kit for right-hand connection EMMETI spa - Via Brigata Osoppo, Vigonovo frazione di Fontanafredda (PN) - Italia Tel Fax info@emmeti.com Rev Ufficio Pubblicità & Immagine - BT / ll rights are reserved. This publication nor any of its contents can be reproduced or publicized without Emmeti s written authorization