Config guide.qxd :37 Pagina a Configuration Guide
|
|
- Carol Harmon
- 7 years ago
- Views:
Transcription
1 Configuration Guide
2 10/2000 Intermec Technologies Corporation. All rights reserved. Edition 1.0 P/N: October 2000
3 Programming with barcodes The BARCODE PROGRAMMING feature gives the possibility to change the Intermec scanner settings without any tools or dismounting the scanner from the checkstand.
4
5 Table of contents Change scanner settings Factory default settings Default message format Programming flow chart 1. General 1.1 Open programming mode /Close programming mode with update 1.2 Close programming mode without update 1.3 Return to factory default settings 1.4 Return to custom default settings 2. Scanner functionality 2.1 Speaker settings Speaker frequency Speaker volume 2.2 Sleep mode Sleep mode off Sleep mode after 30 minutes (default) Sleep mode after 60 minutes 2.3 Scanner timing Same code delay 300msec Same code delay 600msec (default) 3. Communication parameters 3.1 RS232 communication Baudrate Baudrate 9600 (default) 1
6 3.1.6 Baudrate Parity none (default) Parity even Parity odd databits databits (default) stop bit stop bits (default) RTS/CTS on RTS/CTS off (default) RS232 Preset RS232 Preset RS232 Preset RS232 Preset RS232 Preset RS232 Preset RS232 Preset OCIA communication OCIA byte format DTS (default) OCIA byte format NCR short OCIA byte format NCR long OCIA Preset OCIA Preset OCIA Preset OCIA Preset IBM RS485 communication IBM fixed POS scanner (default) IBM handheld scanner emulation 2
7 3.4 Keyboard Wedge communication Terminal type PC/AT (default) Terminal type PS International keyboard (Alt method) (default) US keyboard French keyboard German keyboard User defined keyboard Inter character delay 0msec Inter character delay 2msec (default) Inter character delay 5msec Inter character delay 10msec Inter character delay 20msec 4. Decoding parameters 4.1 Decoder selection EAN/UPC on + AddOn off (default) EAN/UPC on + AddOn on EAN/UPC on + AddOn mandatory on (for 379/434/439/529/977) Code 128/EAN 128 on Code 128/EAN 128 off Code 39 on Code 39 full ASCII on Code 32 on Code 39/Code 32 off Codabar on Codabar off Interleaved 2/5 on Interleaved 2/5 off 3
8 4.2 Decoder configuration Set min. length Interleaved 2/ Length = Length = Length = 8 (default) Length = Length = Length = Data formatting 5.1 Preambles Free programmable preambles: Open programming mode/close programming without update Free programmable preambles: Close programming mode with update 5.2 Postambles Predefined postamble = CR Predefined postamble = LF Predefined postamble = CR + LF Postamble = free format Free programmable postambles: Open programming mode/close programming mode without update Free programmable postambles: Close programming mode with update 5.3 Code identifiers Set message format with code identifiers Set message format without code identifiers 4
9 5.4 Code representation UPCA transmitted as UPCA (12 digits) UPCA transmitted as EAN13 (with leading zero) UPCE to UPCA expansion: ON UPCE to UPCA expansion: OFF UPCE with leading zero UPCE without leading zero UPCE with check digit UPCE without check digit 6. Appendix 6.1 Predefined ASCII characters SOH STX ETX EOT TAB (KBW ONLY) Enter (NUMERIC) (KBW ONLY) 7. Polaris interface selection 7.1 Return to Keyboard Wedge Default 7.2 Return to RS232 Default 7. 1 Polaris features Enable search mode Disable search mode Select single line Select freeze frame 5
10 Change scanner settings In order to change the scanner settings please follow the sequence below: 1. OPEN the scanner Programming Mode by scanning code CHANGE SCANNER SETTINGS by scanning any of the codes 1.3 to 7.x.x. 3. CLOSE the scanner Programming Mode by scanning code 1.1. Reading the OPEN/CLOSE code 1.1 gives a double tone beep (Low High). An example: For changing the baudrate to 4800 the following codes must be scanned successively: > > 1.1 6
11 After reading a valid barcode in Programming Mode the scanner will give a High beep. The scanner will generate a Low beep after receiving an unexpected code. Reading a code, for example a predefined ASCII character, directly after entering the Programming Mode, is not allowed and the scanner will not accept this data. At any moment (in Programming Mode) you can scan code 1.2 to close the programming mode without update, or code 1.3 to return to default settings. 7
12 Factory default settings SLEEP MODE Sleep mode SCANNER TIMING Same code delay RS232 COMMUNICATION Baudrate Parity Data bits Stop bits RTS/CTS Postamble OCIA COMMUNICATION OCIA byte format IBM RS485 COMMUNICATION Mode KEYBOARD WEDGE COMMUNICATION Terminal type Keyboard Inter character delay Postamble DECODER SELECTION EAN/UPC Code 128/EAN 128 Code 39 Code 32 Codabar Interleaved 2/5 DECODER CONFIGURATION Min. length Interleaved 2/5 CODE IDENTIFIERS Code identifiers DEFAULT After 30 minutes DEFAULT 600msec DEFAULT 9600 None 8 2 Off <CR> DEFAULT DTS DEFAULT IBM fixed POS scanner DEFAULT PC/AT International (Alt method) 2msec Enter (Alpha numeric) DEFAULT On (AddOn Off) Off Off Off Off Off DEFAULT 8 DEFAULT Off 8
13 Default message format CODE EAN13 EAN8 UPCA UPCE Code 128 EAN 128 Code 39 Code 32 Codabar Interleaved 2/5 MESSAGE FORMAT D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D1 D2 D3 D4 D5 D6 D7 D8 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D1 D2 D3 D4 D5 D6 D7 D1 - Dx ]C1 D1 - Dx D1 - Dx D1 - Dx D1 - Dx D1 - Dx Important: Please note that EAN/UPC codes with AddOn are transmitted without a separator. 9
14 Programming flow chart CHANGE SCANNER SETTINGS OPEN PROGRAMMING MODE BY SCANNING CODE 1.1 OR BY SLEEPMODE BUTTON (U.S. PROGRAMMING MODE) CHANGE SCANNER SETTINGS BY SCANNING CODE x.x CLOSE PROGRAMMING MODE BY SCANNING CODE 1.1 SAVE AND EXIT 10
15 1. General
16 Configuration Guide General OPEN PROGRAMMING MODE/ CLOSE PROGRAMMING MODE WITH UPDATE 1.1 Important: This code does not apply for scanners used in the USA concerning the Open Programming Mode. To Open Programming Mode press the sleep mode switch for 3-8 seconds. To Close Programming Mode with Update scan code
17 Configuration Guide General CLOSE PROGRAMMING MODE WITHOUT UPDATE
18 Configuration Guide General RETURN TO FACTORY DEFAULT SETTINGS 1.3 Use this code to return to the original factory default settings. Important: Programming Mode is closed after scanning this code. 14
19 Configuration Guide General RETURN TO CUSTOM DEFAULT SETTINGS 1.4 Important: Programming Mode is closed after scanning this code. 15
20 Configuration Guide 16
21 2. Scanner functionality
22 Configuration Guide 18
23 2.1 Speaker settings
24 Configuration Guide Speaker settings SPEAKER FREQUENCY SPEAKER VOLUME
25 2.2 Sleep mode
26 Configuration Guide Sleep mode SLEEP MODE OFF SLEEP MODE AFTER 30 MINUTES (DEFAULT)
27 Configuration Guide Sleep mode SLEEP MODE AFTER 60 MINUTES
28 Configuration Guide 24
29 2.3 Scanner timing
30 Configuration Guide Scanner timing SAME CODE DELAY 300MSEC SAME CODE DELAY 600MSEC (DEFAULT)
31 3. Communication parameters
32 Configuration Guide 28
33 3.1 RS232 communication
34 Configuration Guide RS232 communication BAUDRATE BAUDRATE 9600 (DEFAULT)
35 Configuration Guide RS232 communication BAUDRATE PARITY NONE (DEFAULT)
36 Configuration Guide RS232 communication PARITY EVEN PARITY ODD
37 Configuration Guide RS232 communication 7 DATABITS DATABITS (DEFAULT)
38 Configuration Guide RS232 communication 1 STOP BIT 3.1.2O 2 STOP BITS (DEFAULT)
39 Configuration Guide RS232 communication RTS/CTS ON RTS/CTS OFF (DEFAULT)
40 Configuration Guide RS232 communication RS232 PRESET RS232 PRESET
41 Configuration Guide RS232 communication RS232 PRESET RS232 PRESET
42 Configuration Guide RS232 communication RS232 PRESET RS232 PRESET
43 Configuration Guide RS232 communication RS232 PRESET
44 Configuration Guide 40
45 3.2 OCIA communication
46 Configuration Guide OCIA communication OCIA BYTE FORMAT DTS (DEFAULT) OCIA BYTE FORMAT NCR SHORT
47 Configuration Guide OCIA communication OCIA BYTE FORMAT NCR LONG OCIA PRESET
48 Configuration Guide OCIA communication OCIA PRESET OCIA PRESET
49 Configuration Guide OCIA communication OCIA PRESET
50 Configuration Guide 46
51 3.3 IBM RS485 communication
52 Configuration Guide IBM RS485 communication IBM FIXED POS SCANNER (DEFAULT) IBM HANDHELD SCANNER EMULATION
53 3.4 Keyboard Wedge communication
54 Configuration Guide KBW communication TERMINAL TYPE PC/AT (DEFAULT) TERMINAL TYPE PS
55 Configuration Guide KBW communication INTERNATIONAL KEYBOARD (ALT METHOD) (DEFAULT) US KEYBOARD
56 Configuration Guide KBW communication FRENCH KEYBOARD GERMAN KEYBOARD Other keyboards available through download utility.
57 Configuration Guide KBW communication USER DEFINED KEYBOARD INTER CHARACTER DELAY 0MSEC
58 Configuration Guide KBW communication INTER CHARACTER DELAY 2MSEC (DEFAULT) INTER CHARACTER DELAY 5MSEC
59 Configuration Guide KBW communication INTER CHARACTER DELAY 10MSEC INTER CHARACTER DELAY 20MSEC
60 Configuration Guide 56
61 4. Decoding parameters
62 Configuration Guide 58
63 4.1 Decoder selection
64 Configuration Guide Decoder selection EAN/UPC ON + ADDON OFF (DEFAULT)
65 Configuration Guide Decoder selection EAN/UPC ON + ADDON ON
66 Configuration Guide Decoder selection EAN/UPC ON + ADDON MANDATORY ON (FOR 379/434/439/529/977) Important: After scanning this code, bar codes starting with 379, 434, 439, 529 or 977 will only be accepted including AddOn. If no AddOn has been found, the bar code will not be accepted. Bar codes starting with different characters are accepted with or without AddOn. 62
67 Configuration Guide Decoder selection CODE 128/EAN 128 ON CODE 128/EAN 128 OFF
68 Configuration Guide Decoder selection CODE 39 ON CODE 39 FULL ASCII ON
69 Configuration Guide Decoder selection CODE 32 ON CODE 39/CODE 32 OFF
70 Configuration Guide Decoder selection CODABAR ON CODABAR OFF
71 Configuration Guide Decoder selection INTERLEAVED 2/5 ON (Select a minimum code length using the appropriate barcodes in paragraph 4.2) INTERLEAVED 2/5 OFF
72 Configuration Guide 68
73 4.2 Decoder configuration
74 Programming flow chart minimum length Interleaved 2/5 PROGRAMMING MINIMUM LENGTH INTERLEAVED 2/5 SET MINIMUM LENGTH INTERLEAVED 2/5 (SCAN CODE 4.2.4) LENGTH (SCAN CODE ) SAVE AND EXIT 70
75 Configuration Guide Decoder configuration SET MIN. LENGTH INTERLEAVED 2/ LENGTH =
76 Configuration Guide Decoder configuration LENGTH = LENGTH = 8 (DEFAULT)
77 Configuration Guide Decoder configuration LENGTH = LENGTH =
78 Configuration Guide LENGTH =
79 5. Data formatting
80 Configuration Guide 76
81 5.1 Preambles
82 Programming sequence preambles The scanner can be programmed to output bar code data according to the following format: [PREAMBLE STRING] [BAR CODE DATA] The preamble string is limited to a maximum length of 3 characters. Use the chart on the next page to program the preamble string. Example: to send a <STX> in front of the bar code data, scan successively (while in Programming Mode) Free programmable preambles: Open programming mode <STX> Free programmable preambles: Close programming mode with update As a result, the scanner will give the following bar code data output: [<STX>] [BAR CODE DATA] 78
83 Programming flow chart preambles PROGRAMMING PREAMBLE STRING OPEN PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES (SCAN CODE 5.1.1) SELECT PREAMBLE CHARACTER (SCAN CODE 6.1.X) YES NUMBER OF PREAMBLE CHARACTERS = 3? NO SAVE AND EXIT MORE PREAMBLE CHARACTERS TO BE PROGRAMMED? YES NO SAVE PROGRAMMED DATA? YES NO CLOSE PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES WITHOUT UPDATE (SCAN CODE 5.1.1) CLOSE PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES WITH UPDATE (SCAN CODE 5.1.2) EXIT SAVE AND EXIT 79
84 Configuration Guide Preambles FREE PROGRAMMABLE PREAMBLES: OPEN PROGRAMMING MODE /CLOSE PROGRAMMING MODE WITHOUT UPDATE FREE PROGRAMMABLE PREAMBLES: CLOSE PROGRAMMING MODE WITH UPDATE
85 5.2 Postambles
86 Programming sequence postambles The scanner can be programmed to output bar code data according to the following format: [BAR CODE DATA] [POSTAMBLE STRING] The postamble string is limited to a maximum length of 3 characters. Use the chart on the next page to program the postamble string. Example: to send a <ETX> after the bar code data, scan successively (while in Programming Mode) Free programmable postambles: Open programming mode <ETX> Free programmable postambles: Close programming mode with update As a result, the scanner will give the following bar code data output: [BAR CODE DATA] [<ETX>] 82
87 Programming flow chart postambles PROGRAMMING POSTAMBLE STRING POSTAMBLE = FREE FORMAT (SCAN CODE 5.2.4) OPEN PROGRAMMING MODE FREE PROGRAMMABLE POSTAMBLES (SCAN CODE 5.2.5) SELECT POSTAMBLE CHARACTER (SCAN CODE 6.1.X) YES NUMBER OF POSTAMBLE CHARACTERS = 3? NO SAVE AND EXIT MORE POSTAMBLE CHARACTERS TO BE PROGRAMMED? YES NO SAVE PROGRAMMED DATA? YES NO CLOSE PROGRAMMING MODE FREE PROGRAMMABLE POSTAMBLES WITHOUT UPDATE (SCAN CODE 5.2.5) CLOSE PROGRAMMING MODE FREE PROGRAMMABLE POSTAMBLES WITH UPDATE (SCAN CODE 5.2.6) EXIT SAVE AND EXIT 83
88 Configuration Guide Postambles PREDEFINED POSTAMBLE = CR PREDEFINED POSTAMBLE = LF
89 Configuration Guide Postambles PREDEFINED POSTAMBLE = CR + LF POSTAMBLE = FREE FORMAT
90 Configuration Guide Postambles FREE PROGRAMMABLE POSTAMBLES: OPEN PROGRAMMING MODE /CLOSE PROGRAMMING MODE WITHOUT UPDATE FREE PROGRAMMABLE POSTAMBLES : CLOSE PROGRAMMING MODE WITH UPDATE
91 5.3 Code identifiers
92 Set message format with code identifiers A code identifier is a data string, giving information to the host system concerning the bar code type that has been read. After scanning code the scanner is programmed to transmit data according to the following format: CODE EAN13 EAN8 UPCA UPCE Code 128 EAN 128 Code 39 Code 32 Codabar Interleaved 2/5 CODE IDENTIFIER F FF A E # P * * % i MESSAGE FORMAT D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D1 D2 D3 D4 D5 D6 D7 D8 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 0 D1 D2 D3 D4 D5 D6 D1 - Dx ]C1 D1 - Dx D1 - Dx D1 - Dx D1 - Dx D1 - Dx Important: Please note that the UPCE format will be changed. The scanner will transmit UPCE codes with leading zero and without check digit. To return to the Scantech default format without code identifiers scan code
93 Configuration Guide Code identifiers SET MESSAGE FORMAT WITH CODE IDENTIFIERS SET MESSAGE FORMAT WITHOUT CODE IDENTIFIERS
94 Configuration Guide 90
95 5.4 Code representation 91
96 Configuration Guide Code representation UPCA FORMAT TRANSMITTED AS UPCA (12 DIGITS) UPCA FORMAT TRANSMITTED AS EAN13 (WITH LEADING ZERO)
97 Configuration Guide Code representation UPCE FORMAT UPCE TO UPCA EXPANSION: ON UPCE FORMAT UPCE TO UPCA EXPANSION: OFF
98 Configuration Guide Code representation UPCE FORMAT WITH LEADING ZERO UPCE FORMAT WITHOUT LEADING ZERO
99 Configuration Guide Code representation UPCE FORMAT WITH CHECK DIGIT UPCE FORMAT WITHOUT CHECK DIGIT
100 Configuration Guide 96
101 6. Appendix
102 Predefined ASCII characters
103 Configuration Guide 99
104 Configuration Guide Predefined ASCII characters SOH STX
105 Configuration Guide Predefined ASCII characters ETX EOT
106 Configuration Guide Predefined ASCII characters TAB (KBW ONLY) ENTER (NUMERIC) (KBW ONLY)
107 7. Polaris interface selection 103
108 Configuration Guide Polaris interface selection RETURN TO KEYBOARD WEDGE DEFAULT 7.1 RETURN TO RS232 DEFAULT 7.2 Important: Programming Mode is closed after scanning these codes. 104
109 7.1 Polaris features 105
110 Configuration Guide Polaris features User instructions: Freeze Frame / Single Line The Polaris featuring the Freeze Frame and the Single Line option, enables the user to temporarily switch from the full scan pattern (the Omni directional mode) to a blinking, multiple scan pattern called Freeze Frame, or to a Single Line preventing the wrong bar code being read. These features are especially helpful on sheets or products where multiple bar codes are printed. 1. Press the button on top of the scanner. Dependent on which feature is chosen, the scanner s scan pattern will change from the multiple scan lines, to either a blinking multiple scan pattern or to just one single Line. 2. Direct the blinking multiple scan pattern/single line onto the required bar code, whilst holding the button. 106
111 Configuration Guide Polaris features 3. Once the scan pattern/line is completely crossing the bar code, release the button. The scanner generates a beep indicating the scanner has read the bar code. 4. After a successful read, the blinking multiple scan pattern/single line will disappear, and the scanner will return to the normal Omni directional mode. To use the Freeze Frame/Single Line option again, follow steps one to four. To activate the Freeze Frame/Single Line: 1. Scan code Enable Search Mode. 2. Scan code for Single Line or code for Freeze Frame. Turn off Freeze Frame/ Single Line by scanning code
112 Configuration Guide Polaris features ENABLE SEARCH MODE DISABLE SEARCH MODE
113 Configuration Guide Polaris features SELECT SINGLE LINE SELECT FREEZE FRAME
114 Intermec Technologies Corporation: North America / Asia Pacific / Latin America * th Avenue West, PO Box 4280, Everett, WA Tel: * Fax: * U.S. service and technical support, tel: Canadian service and technical support, tel: Europe / Middle East / Africa * Sovereign House, Vastern Road, Reading RG1 8BT, England Tel: * Fax: Internet: info@intermec.com Technical information:
Laser Barcode Scanner User s Manual
Laser Barcode Scanner User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
More informationBARCODE READER V 2.1 EN USER MANUAL
BARCODE READER V 2.1 EN USER MANUAL INSTALLATION OF YOUR DEVICE PS-2 Connection RS-232 Connection (need 5Volts power supply) 1 INSTALLATION OF YOUR DEVICE USB Connection 2 USING THIS MANUAL TO SETUP YOUR
More informationLaser Barcode Scanner
Laser Barcode Scanner User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
More informationXi2000 Series Configuration Guide
U.S. Default Settings Sequence Reset Scanner Xi2000 Series Configuration Guide Auto-Sense Mode ON UPC-A Convert to EAN-13 OFF UPC-E Lead Zero ON Save Changes POS-X, Inc. 2130 Grant St. Bellingham, WA 98225
More informationPart No. : MUL-53221-07 PROGRAMMING GUIDE
Part No. : MUL-53221-07 PROGRAMMING GUIDE PROGRAMMING GUIDE for BARCODE SCANNERS The guide can be used as keyboard emulation, RS- 232C serial interface, and USB 1.1 interface and wand emulation. IMPORTANT
More informationBarcode Magstripe. Decoder & Scanner. Programming Manual
Barcode Magstripe Decoder & Scanner Programming Manual CONTENTS Getting Started... 2 Setup Procedures... 3 Setup Flow Chart...4 Group 0 : Interface Selection... 5 Group 1 : Device Selection for keyboard
More informationDUET / VS800 Scanner. DUET Scanner VS800 Scanner. Programming Kit
DUET / VS800 Scanner DUET Scanner VS800 Scanner Programming Kit PSC Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Telefax: (541) 345-7140 PSC and the PSC logo are registered
More informationMetroSelect Programming Guide. MLPN 2407/December 1998
MetroSelect Programming Guide MLPN 2407/December 1998 Locations: USA Corporate Headquarters Europe Metrologic Instruments, Inc. Metrologic Instruments GmbH 90 Coles Road Dornierstrasse 2 Blackwood, NJ
More informationAllen-Bradley. Bar Code. 2-D Hand-Held. Programming Guide. Bar Code. Scanners. (Cat. No. 2755-HTG-4)
Allen-Bradley 2-D Hand-Held Bar Code Scanners Bar Code Programming Guide (Cat. No. 2755-HTG-4) Important User Information The illustrations, charts, sample programs and layout examples shown in this guide
More informationCD-3860 Bar Code Scanner User s Manual
CD-3860 Bar Code Scanner User s Manual Important Notice Rev. Original No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or
More informationEnter/Exit programming
P/N: MUL-53247-02 Enter/Exit programming (This barcode is also found at back cover page.) Framed values are default values. All Rights Reserved This guide is designed for advanced settings of Hand Free
More informationHANDHELD LASER SCANNER
HANDHELD LASER SCANNER PROGRAMMING GUIDE PSC Scanning, Inc. En Suisse: 959 Terry Street GOMARO s.a. Eugene, Oregon 97402-9120 1123 Aclens - Switzerland Telephone: (541) 683-5700 http://www.gomaro.ch/ Toll
More informationE-i. Section E. Code Formatting. E/D = Enable/Disable T/DNT = Transmit/Do Not Transmit EX/DNEX = Expand/Do Not Expand
Section E Code Formatting E/D = Enable/Disable T/DNT = Transmit/Do Not Transmit EX/DNEX = Expand/Do Not Expand C/DNC = Convert/Do Not Convert E/DNE = Enable/Do Not Enable T/DNT UPC-A Check Digit (E - 1)
More informationVoyager 9520/40 Voyager GS9590 Eclipse 5145
Voyager 9520/40 Voyager GS9590 Eclipse 5145 Quick Start Guide Aller à www.honeywellaidc.com pour le français. Vai a www.honeywellaidc.com per l'italiano. Gehe zu www.honeywellaidc.com für Deutsch. Ir a
More informationIndex...1. Introduction...3. Installation- Keyboard Wedge...3 RS-232...3 USB...3. Default Setting for each barcode shown as below:...
Index Index...1 Introduction...3 Installation- Keyboard Wedge...3 RS-232...3 USB...3 Default Setting for each barcode shown as below:...4 Programming the MS320...5 Interface Selection...7 Keyboard wedge...8
More informationBI-300. Barcode configuration and commands Manual
BI-300 Barcode configuration and commands Manual 1. Introduction This instruction manual is designed to set-up bar code scanner particularly to optimize the function of BI-300 bar code scanner. Terminal
More informationMETROLOGIC INSTRUMENTS INC. MetroSelect Single-Line Configuration Guide
METROLOGIC INSTRUMENTS INC. MetroSelect Single-Line Configuration Guide Copyright 2005 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted, or stored
More informationMK-SERIE 1000/1500/2000 AllOfBarcode.de Michael Krug - 83278Traunstein BARCODE SCANNER
MK-SERIE 1000/1500/2000 AllOfBarcode.de Michael Krug - 83278Traunstein BARCODE SCANNER Configuration Guide - 1 - Table of Contents Chapter 1 System Information 1.1 About this manual 3 1.2 How to set up
More informationMETROLOGIC INSTRUMENTS, INC. MetroSelect Configuration Guide
METROLOGIC INSTRUMENTS, INC. MetroSelect Configuration Guide Copyright 2005 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted, or stored in any form
More informationScanner Configuration
Scanner Configuration SmartScan Manual DOC Version 2.21 This document is specifically designed for the user to print two pages per sheet of paper with optimal print quality. Copyright 2005~ 2008 CIPHERLAB
More informationEnter/Exit Programming Mode
Enter/Exit Programming Mode (This barcode can also be found at back cover page.) Framed values are default values. IMPORTANT NOTICE No warranty of any kind is made in regard to this material, including,
More informationIntroduction. Setting Up the Scanner. Performing Verification Sequence
MDE-4389A Setting Up Datalogic DLL2020 Bar Code Scanner Used on Profit Point Terminal September 2005 Introduction If you have a Polaris bar code scanner, refer to C35424 Setting Up Your Polaris Bar Code
More informationBarcode Scanner User Manual V6.6.2
Barcode Scanner User Manual V6.6.2 CONTENTS.......................................................................................... 1 1 2 2 3 4 13 14 15 17 17 19 19 20 22 23 23 28 29 33 42 60 65 85 87
More informationQuickScan i. QD2100 Barcode Imager. Product Reference Guide
QuickScan i QD2100 Barcode Imager Product Reference Guide Configuring the Interface KEYBOARD FEATURES AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/standard Key Encoding Select KBD-AT Keyboard
More informationBar Code CCD Scanner OPERATION MANUAL
ISO 9002 Certified Lead with technology Win customers with service Bar Code CCD Scanner OPERATION MANUAL 69 Jarltech International Inc. 1998. All rights reserved. Under the copyright laws, this manual
More informationMetroSelect. Single-Line Scanner. Configuration Guide
MetroSelect Single-Line Scanner Configuration Guide Disclaimer Honeywell International Inc. ( HII ) reserves the right to make changes in specifications and other information contained in this document
More informationRevision History. Advanced Handheld CCD/Laser Scanner
Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 September 9, 2010 Initial release 1.1 February 18, 2011 Added Blink mode selections. i Important
More informationDL910 SERIES. Instruction Manual
DL910 SERIES Instruction Manual DL910 SERIES INSTRUCTION MANUAL ALL RIGHTS RESERVED Datalogic reserves the right to make modifications and improvements without prior notification. Datalogic shall not
More informationTaoTronics Laser Barcode Scanner User s Manual
TaoTronics Laser Barcode Scanner User s Manual SETUP from PC keyboard For KBW or KBW/RS232 interface 1 Features * Simple installation,keyboard Wedge Serial, Wand Emulation tc * Superior keyboard wedge
More informationConfigure Your FuzzyScan
Configure Your FuzzyScan A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding Before you trying to configure the FuzzyScan, you must refer to the Quick Installation chapter of reading devices
More informationMetrologic MS1690 2D Scanner Installation Guide
Metrologic MS1690 2D Scanner Installation Guide Revision 1.0 Revision History 1.0 04/17/2007 Initial Release The latest version of this document can be found in the following places: Internally for Cerner
More informationMS100 Bar Code Pen Reader
MS100 Bar Code Pen Reader AdventureJan General Advisory Improper handling, storage, environmental influences and /or product modification can lead to problems during use. This is particularly true if repairs
More informationBarcode reader setup manual
Barcode reader setup manual Setup procedures are as follows: 1 Scan Begin setting 2 Scan your required function and its corresponding barcode 3 Scan End setting 4 All the setting parameters will be saved
More informationMetroSelect Single Line Configuration Guide. MS9500 Voyager Series i
MetroSelect Single Line Configuration Guide MS9500 Voyager Series i LOCATIONS Corporate Headquarters Metrologic Instruments, Inc. Customer Service: 1-800-ID-METRO 90 Coles Road Tel: 856-228-8100 Blackwood,
More informationBarcode Scanning Made Easy. Programming Guide
Barcode Scanning Made Easy Programming Guide CCD Scanner Programming Guide Please Read Note: The Wasp WCS3900 Series Scanners are ready to scan the most popular barcodes out of the box. This manual should
More informationLaser Scanner Programming Guide (SE923 laser engine)
Laser Scanner Programming Guide (SE923 laser engine) CONTENT Technical note... 5 How to recognise the type of the laser barcode engine... 5 How to program the laser barcode reader into default value...
More informationWireless Laser Barcode Scanner ils 6300BU. User s Manual
Wireless Laser Barcode Scanner ils 6300BU User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
More informationNOTICE: respective owner. Note: Specification is subject to changes without. notice.
0 NOTICE: This device complies with Part 15 of the FCC Rules. Operation shall be subject to the following two conditions: (1) This device may not cause harmful interface, and (2) This device must accept
More informationHAND-HELD DEVICES II. Software Configuration Manual
HAND-HELD DEVICES II Software Configuration Manual HAND-HELD DEVICES II SOFTWARE CONFIGURATION MANUAL DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy Hand-Held Devices
More informationMK-5200 2D Imager Barcode Scanner Configuration Guide
MK-5200 2D Imager Barcode Scanner Configuration Guide V 1.2 Programming the Engine Code Programming On/Off Read the barcode to activate Code Programming function. One or more Code Programming barcodes
More informationScanner Configuration Manager Manual. for PC type computers
Scanner Configuration Manager Manual for PC type computers TABLE OF CONTENTS 1. SCANNER CONFIGURATION MANAGER......... 1 Start it Up...................... 1 First Look...................... 3 Settings......................
More informationAdvanced Handheld High-Speed Laser Scanner
1 Revision History Changes to the original manual are listed below: Version Date of Version 1.0 Jun. 25, 2010 Initial release 1.1 Sep. 07, 2010 Add configuration barcode value. Add settings of Code 11,
More informationBARCODE IMAGER. Programming Manual International Edition, Rev. A1
BARCODE IMAGER International Edition, Rev. A Revision History Rev. No. Released Date Description Rev.. Beta Aug., 8 First Release Rev.. Beta Aug., 8 Page 9 Vibrator Default value is changed from Disable
More informationS302D. Programming Guide. 2D Imaging Barcode Scanner. Advanced Handheld High-Speed Laser Scanner
S302D 2D Imaging Barcode Scanner Programming Guide 1 Advanced Handheld High-Speed Laser Scanner Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0
More informationQuickScan QS6500/QS6500BT
QuickScan QS6500/QS6500BT Product Reference Guide PSC Inc 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents
More informationBCST-20 Barcode Scanner. Instruction Manual. www.inateck.com
BCST-20 Barcode Scanner Instruction Manual www.inateck.com IMPORTANT NOTICE Safety Precaution * DO NOT disassemble the scanner, or place foreign matter into the scanner causing a short circuit or circuit
More informationQuickScan Mobile. Reference Manual
QuickScan Mobile Reference Manual Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of
More informationBarcode Scanning Made Easy. WWS500 Programming Guide
Barcode Scanning Made Easy WWS500 Programming Guide Table of Contents Chapter 1. Introduction...........................2 Chapter 2. Barcode Symbologies...................3 Chapter 3. Quick Start............................4
More informationTable of Contents Appendix
Table of Contents Configure Your FuzzyScan...- Bar Code Programming Menu...- Programming Procedures...- Host Interface Selection...- Symbology Reading Control...- Keyboard Interface Control...- Serial
More informationCT20 Barcode Scanner User Manual
CT20 Barcode Scanner User Manual IMPORTANT NOTICE Safety Precaution * DO NOT disassemble the scanner, or place foreign matter into the scanner cause a short circuit or circuit damage. * DO NOT expose the
More informationCCD Programming Guide
CCD Programming Guide Please Read Note: The Wasp CCD Scanner is ready to scan the most popular bar codes out of the box. This manual should only be used to make changes in the configuration of the scanner
More informationOPN_DL UTILITY SOFTWARE. INSTALLATION AND USER GUIDE - v2.03
OPN_DL UTILITY SOFTWARE INSTALLATION AND USER GUIDE - v2.03 Electronic Reading Systems Ltd 14 Wolseley Business Park Kempston Beds MK42 7PW Tel: 01234 855300 Fax: 01234 855446 CONTENTS 1.0 INTRODUCTION
More informationQUICK START GUIDE. Wasp WLS 9500. www.waspbarcode.com
QUICK START GUIDE Wasp WLS 9500 www.waspbarcode.com LED Scan Window Beeper Trigger CORD ATTACHMENT Model Number and Serial Number appear here. Cable interface Interface cable modular connector Interface
More informationProduct Reference Guide. QuickScan TM QS6500/QS6500BT. General Purpose Handheld Linear Imager Bar Code Reader with Bluetooth Wireless Technology
QuickScan TM QS6500/QS6500BT General Purpose Handheld Linear Imager Bar Code Reader with Bluetooth Wireless Technology Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402
More informationAPPENDIX E COMMAND BARCODES
APPENDIX E COMMAND BARCODES Scan command barcode(s) to quickly configure the Socket Bluetooth Cordless Hand Scanner v3 (1D laser versions). By default, the CHS is in HID mode as a Keyboard device. IMPORTANT!
More informationTMCT-10 Barcode Scanner User Manual. 102, 5661-99 St. Edmonton, AB T6E 3N8 Ph. 780.988.0215 Fax 780.988.0465
TMCT-10 Barcode Scanner User Manual 102, 5661-99 St. Edmonton, AB T6E 3N8 Ph. 780.988.0215 Fax 780.988.0465 IMPORTANT NOTICE Safety Precaution * DO NOT disassemble the scanner, or place foreign matter
More informationProduct Reference Guide
PowerScan 7000 SRI Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part
More informationbecause we care MS910 Wireless Barcode Scanner Quick Guide Full user s manual is available on the enclosed CD. Version 1.2 400947G
because we care MS910 Wireless Barcode Scanner Quick Guide Full user s manual is available on the enclosed CD. Version 1.2 400947G because we care OUT OF THE BOX INTRODUCTION 2. Trigger 3. LED Indicator
More informationUser s Manual. Decoding Laser Scanner P/N 063496-003
User s Manual Decoding Laser Scanner P/N 063496-003 Intermec Corporation 6001 36th Avenue West P.O. Box 4280 Everett, WA 98203-9280 U.S. service and technical support: 1-800-755-5505 U.S. media supplies
More informationMD6 Series 2D Barcode Scanner
MD6 Series 2D Barcode Scanner User Manual Version: MD6_UM_EN_V1.1.9 2 Warning: Ensure that the optional DC adapter works at +5V, especially for the RS-232 interface cable. NOTICE: 1. All software, including
More informationSocketScan Software Advanced Programming Guide
SocketScan Software Advanced Programming Guide A guide to help you program symbology and parameter settings for the following Socket barcode scanning products: Secure Digital Scan Card Series 3 CompactFlash
More informationUSER'S GUIDE NUSCAN 2100 Series
BARCODE SCANNER USER'S GUIDE NUSCAN 2100 Series Table of Contents 1. Limited Warranty...1 2. Introduction...2 3. Contents...3 4. Barcode Symbologies...3 5. Product Introduction...3 6. Installation...4
More informationLS6300 Lecteur de code-barres laser
WWW.SYMCOD.COM Manuel LS6300 Lecteur de code-barres laser Version: 30/04/2013 Introduction Le lecteur laser Symcod LS6300 est une solution très abordable pour la gestion de vos opérations. Toujours à la
More informationWireless Scanner. User s Manual - MS910 - Version 1.0
Wireless Scanner - MS910 - User s Manual Version 1.0 Table of Contents Chapter 1 Overview... 1 Introducing the MS910... 1 Package Contents... 2 Chapter 2 Installation and Connection... 5 Connecting (Pairing)
More informationBluetooth Version FUZZYSCAN FAMILY. Quick Start Guide WIRELESS SCANNER
Bluetooth Version FUZZYSCAN FAMILY Quick Start Guide WIRELESS SCANNER Getting Familiar with Your FuzzyScan Thank you for choosing Cino FuzzyScan Bluetooth Cordless Image Scanner. Powered by the combination
More informationQuick Installation. A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding. Quick Installation
Quick Installation A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding This chapter intends to get your new FuzzyScan scanner working with your existing system within minutes. General instructions
More informationBar Code Reader Models 1000/1002 USER'S MANUAL 2190 Regal Parkway Euless, TX 76040 (817) 571-9015 (800) 648-4452 FAX (817) 685-6232 FCC NOTICE WARNING: This equipment generates, uses and can radiate radio
More informationUsers Manual. QuickBarII Single-Chip Bar Code Decoder
Users Manual QuickBarII Single-Chip Bar Code Decoder REV E Dec. 22, 2009 LIMITED WARRANTY ID TECH warrants to the original purchaser for a period of 12 months from the date of invoice that this product
More informationMETROLOGIC INSTRUMENTS, INC. IS4225 ScanGlove USB Addendum for the MetroSelect Single-Line Configuration Guide
METROLOGIC INSTRUMENTS, INC. IS4225 ScanGlove USB Addendum for the MetroSelect Single-Line Configuration Guide Copyright 2005 by Metrologic Instruments, Inc. All rights reserved. No part of this work may
More informationSG20T. Tethered Scanner. User s Guide
SG20T Tethered Scanner User s Guide Intermec by Honeywell 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely for the purpose of allowing customers
More informationCHAPTER 8 BAR CODE CONTROL
CHAPTER 8 BAR CODE CONTROL CHAPTER 8 BAR CODE CONTROL - 1 CONTENTS 1. INTRODUCTION...3 2. PRINT BAR CODES OR EXPANDED CHARACTERS... 4 3. DEFINITION OF PARAMETERS... 5 3.1. Bar Code Mode... 5 3.2. Bar Code
More informationProgramming Menu V3.9
BAR CODE Programming Menu V3.9 Notice The manufacturer shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages in connection with
More informationSymbol LS9203. Product Reference Guide
Symbol LS9203 Product Reference Guide Symbol LS9203 Product Reference Guide 72E-71538-03 Revision A February 2007 Motorola, Inc. 2007. All rights reserved. No part of this publication may be reproduced
More informationQuickScan TM L QD 2300 Bar Code Scanner
QuickScan TM L QD 2300 Bar Code Scanner Product Reference Guide Datalogic ADC, Inc. 959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 2007-2014 Datalogic ADC, Inc. An
More informationTutorial 8: Setting Up a Barcode Scanner
Tutorial 8: Setting Up a Barcode Scanner This tutorial explains how to use a barcode scanner with PranaStudio. PranaStudio allows you to use a scanner on your products and to assign a barcode to a student.
More informationSynergy Controller Application Note 4 March 2012, Revision F Tidal Engineering Corporation 2012. Synergy Controller Bar Code Reader Applications
Synergy Controller Bar Code Reader Applications Synergy Controller with Hand Held Products Bar Code Scanner OCR-A Labeled Part Introduction The value of the ubiquitous Bar Code Scanner for speeding data
More informationSR30. Handheld Scanner. User s Guide
SR30 Handheld Scanner User s Guide Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely
More informationMagellan TM 3200VSi. On-Counter Vertical Presentation Scanner. Product Reference Guide
Magellan TM 3200VSi On-Counter Vertical Presentation Scanner Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 An
More informationQuickScan QS2500 Handheld Bar Code Scanner. Product Reference Guide
QuickScan QS2500 Handheld Bar Code Scanner Product Reference Guide PSC Inc 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved.
More informationCreate!form Barcodes. User Guide
Create!form Barcodes User Guide Barcodes User Guide Version 6.3 Copyright Bottomline Technologies, Inc. 2008. All Rights Reserved Printed in the United States of America Information in this document is
More information1.1 Notice... 3 1.2 Introduction... 4 1.3 Codes Read... 4 1.4 Installation... 4 1.5 Pin Assignment... 6. Configuration - General
BAR CODE Contents Chapter 1 Description 1.1 Notice... 3 1.2 Introduction... 4 1.3 Codes Read... 4 1.4 Installation... 4 1.5 Pin Assignment... 6 Chapter 2 Configuration - General 2.1 Flow Chart... 8 2.2
More informationRegister your product and get support at www.philips.com/dictation DPM8500. Barcode scanner configuration guide
Register your product and get support at www.philips.com/dictation DPM8500 Barcode scanner configuration guide Table of contents 1 Introduction 5 Operational Parameters 5 Parameter defaults 5 2 Set default
More informationScanMaster for Scanner Configuration
ScanMaster for Scanner Configuration For 1 Series Barcode Scanners: 1070, 1500, 1502 (1D, tethered) 1560, 1562, 1660, 1661 (1D, cordless) 1504, 1704 (2D, tethered) 1564, 1664 (2D, cordless) Version 1.30
More informationProgramming Reference Guide HP USB Barcode Scanner
Programming Reference Guide HP USB Barcode Scanner Document Part Number: 430944-002 August 2006 Print this document before setting up the HP USB Barcode Scanner. The document provides the programming bar
More informationMaster-Touch and ValuMass. Modbus Communications. INSTRUCTION MANUAL 80202201 (Rev. 2.1)
Master-Touch and ValuMass Modbus Communications INSTRUCTION MANUAL 80202201 (Rev. 2.1) Eldridge Products, Inc. 2700 Garden Road, Building A Monterey, CA 93940 Tel: 800/321-3569 or 831/648-7777 Fax: 831/648-7780
More informationMINIMAG. Magnetic Stripe Reader Keyboard Wedge. User s Manual
MINIMAG Magnetic Stripe Reader Keyboard Wedge User s Manual TM Agency Approved Specifications for subpart B of part 15 of FCC rule for a Class A computing device. Limited Warranty ID TECH warrants to the
More informationAll brand, product and service, and trademark names are the property of their registered owners.
Copyright 2010 EQUATOR LIMITED All rights reserved. All intellectual property rights are the property of their owners. EQUATOR LIMITED is authorized the right to use the software; it is provided under
More informationMAGELLAN CONNECTING TO CASH REGISTER EXPRESS
MAGELLAN CONNECTING TO CASH REGISTER EXPRESS Programming codes are for the following products: Magellan 8100 Magellan 8200 Magellan 8300 Magellan 8400 Magellan 8500 Magellan 8500XT Magellan 8500XTS Magellan
More informationQuickScan L. Barcode Scanner. Advanced Data Formatting (ADF) Guide
QuickScan L Barcode Scanner Advanced Data Formatting (ADF) Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights
More informationND48-RS ASCII A2.04 Communication Protocol
ND48-RS ASCII A2.04 Communication Protocol SEM 06.2003 Str. 1/6 ND48-RS ASCII A2.04 Communication Protocol ASCII A2.04 protocol provides serial communication with most of the measurement and control devices
More informationGryphon I GD4100/GM4100
Gryphon I GD4100/GM4100 General Purpose Handheld Linear Imager Barcode Reader Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541)
More informationQuickScan TM Lite QW2100
QuickScan TM Lite QW2100 General Purpose Corded Handheld Linear Imager Bar Code Reader Product Reference Guide Datalogic ADC, Inc. 959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541)
More informationGetting Started with POS. Omni POS Getting Started Manual. switched on accounting
Omni POS Getting Started Manual switched on accounting i i Getting Started with Omni POS Table Of Contents Overview...1 Setting up POS...2 Initial Steps...2 Tellers...2 POS Clearing Account...3 Printing...4
More informationWindows Driver Manual Metapace T-4 Thermal Printer Rev. 1.00
Manual Metapace T-4 Thermal Printer Rev. 1.00 http://www.metapace.com Table of Contents 1. Manual Information... 3 2. Operating System (OS) Environment... 3 3. Windows Driver Preparation... 3 4. Windows
More informationBAR CODE CONTROL BAR CODE CONTROL - 1
BAR CODE CONTROL BAR CODE CONTROL - 1 CONTENTS 1. INTRODUCTION... 3 2. PRINT BAR CODES OR EXPANDED CHARACTERS... 4 3. DEFINITION OF PARAMETERS... 5 3.1. Bar Code Mode............ 5 3.2. Bar Code Style,
More information1500/1502 Series Barcode Scanner
1500/1502 Series Barcode Scanner Setup barcodes included. Version 1.20 Copyright 2008~2015 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.;
More information2 Advanced Scanner Configuration Guide
2 Advanced Scanner Configuration Guide Table of contents Introduction...4 Operational Parameters...4 Set Default Parameter...7 Default Parameters...7 Beeper Volume...7 Beeper Tone...8 Beeper Frequency
More informationBARCODE PRINTING SET UP BARCODE PRINTING
21 BARCODE PRINTING The Barcode Printing option can be purchased for an additional cost. You will receive a floppy disk or CD that you can use to activate this feature. SET UP BARCODE PRINTING To start,
More informationPM1122 INT DIGITAL INTERFACE REMOTE
PM1122 INT DIGITAL INTERFACE REMOTE PM1122 INT front panel description: 1. Clear wireless remotes knob: push this button for more than 2 seconds to clear the list of all assigned wireless remote settings
More informationSymbol LS1203. Product Reference Guide
Symbol LS1203 Product Reference Guide LS1203 Product Reference Guide 72E-73953-04 Revision A November 2012 ii Symbol LS1203 Product Reference Guide Motorola Solutions, Inc. All rights reserved. No part
More information