AUTODESK INVENTOR Trial Projects
|
|
|
- Barbara Bryant
- 7 years ago
- Views:
Transcription
1 AUTODESK INVENTOR Trial Projects Exploded Views and Animation Build technical documentation
2 PART 1: POSITIONING COMPONENTS page: After starting Inventor, click the Projects icon in the ribbon. Navigate to where you saved the project files and select Ember-BS-PRE.ipj. 4. In the ribbon, select New. Select the Metric folder and create a new file using the Standard (mm).ipn template. Choose Base Assembly (New).iam as the assembly file to import. In the model window, right click to bring up the marking menu. Select Tweak Components. Change the selection option to Component.
3 PART 1: POSITIONING COMPONENTS page: Select the projector subassembly shown and use the arrow pointing up to drag it approximately 210mm from the base. Click the green checkmark to complete the tweak. 8. Using the model browser, expand the model tree using the arrows next to Scene1 and Ember-BS-PRE.iam. Select the 8 components as shown. Right click in the model window to open the marking menu and select Tweak Components. Use the arrow pointing up (Z-direction) and move them approximately 40mm. Again using the model browser, select the two fans and the same 8 screws moved in the previous operation.
4 PART 1: POSITIONING COMPONENTS page: Restart the Tweak Components command from the marking menu. Move the screws and fans 170mm up in the Z-direction. Click the green checkmark to complete the command. 12. Select the two mounting screws for the control panel subassembly, and then restart Tweak Command to drag them up about 17mm. Select the same two screws and Control Panel Assembly v4 in the model tree and restart Tweak Components. Use the arrows to move them up (Z-dir) 100mm and away (Y-dir) -100mm. Select the 6 screws that are used to hold down the projector assembly as shown.
5 PART 1: POSITIONING COMPONENTS page: Restart Tweak Components and move the screws up 310mm, above the projector assembly. 16. Using the Storyboard panel at the bottom of the screen, move the 6 tweaks shown to the beginning of the timeline so they are in the correct assembly sequence. Using the same methods from Steps 11 and 12, offset the Connecter PCB and its mounting screws, up and away 100mm each from the assembly as shown. The final step is to move the main PCB board and its attachment screws using the same approach.
6 PART 1: POSITIONING COMPONENTS page: At the top of the Storyboard panel, press the Play Current Storyboard button to review the assembly sequence. In the Publish section of the ribbon, pick Video. 19. In the publish dialog, select the box next to Reverse to publish the video in the order of assembly (rather than disassembly) and then select OK to create the video.
7 PART 2: SNAPSHOTS AND DRAWINGS page: To begin creating assembly instruction views, select all of the Tweaks from the browser, and then select Hide Trails from the marking menu. 4. In the Storyboard panel, select the left arrow for Back to Storyboard Beginning and position the assembly in the model window for the first snapshot. In the ribbon, select the View tab. Click the Visual Style drop down and choose Wireframe with Visible Edges Only. Right click in the model window to open the marking menu, and select New Snapshot View.
8 PART 2: SNAPSHOTS AND DRAWINGS page: In the Storyboard panel, move the marker forward to 2.5s to setup the snapshot of the first assembly step. Reposition the model as needed to see the entire exploded view and use the marking menu to create the next snapshot Follow the same steps to move the marker in the storyboard panel to 7.5s to capture the fan disassembly and create another snapshot. Move the timeline to show the Control Panel Subassembly tweak and create another snapshot.
9 PART 2: SNAPSHOTS AND DRAWINGS page: Create the final snapshot at the end of the timeline with the PCBs in their final positions. You can now double click on any snapshot in the Snapshot Views panel to change the view in the model window In the ribbon, select Raster to bring up the dialog to publish images for use in assembly documentation. Choose the desired Image Resolution, File Location, and File Format to publish out the snapshots created as images.
10 PART 2: SNAPSHOTS AND DRAWINGS page: Right click the snapshot of the fully exploded view in the Snapshot Views panel, and choose Create Drawing View. When the Drawing Template dialog appears, select the Metric tab and choose ANSI (mm).dwg as the drawing template Change the Scale to 1:1 and drag the view to an appropriate location on the sheet. Click OK to create the view. In the Annotate tab in the ribbon, select Parts List.
11 PART 2: SNAPSHOTS AND DRAWINGS page: Select the exploded view in the drawing as the Source and click OK. Click to place the parts list in the desired location on the sheet In the Annotate tab in the ribbon, select Auto Balloon. First select the exploded view as the Select View Set and then shift-select all the components in the model browser for Add or Remove Components.
12 PART 2: SNAPSHOTS AND DRAWINGS page: Click the Select Placement icon, change the alignment to Vertical and choose where the balloons should be located on the drawing. Click OK to finish.
13 Autodesk, Autodesk Inventor, and the Autodesk logo are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and/or other countries. All other brand names, product names, or trademarks belong to their respective holders. Autodesk reserves the right to alter product offerings and specifications at any time without notice, and is not responsible for typographical or graphical errors that may appear in this document Autodesk, Inc. All rights reserved.
This Skill Builder demonstrates how to define and place sketched symbols in drawings.
Sketched Symbols This Skill Builder demonstrates how to define and place sketched symbols in drawings. A sketched symbol is a user-defined symbol. You create sketched symbols in the sketch environment
Introduction to Autodesk Inventor for F1 in Schools
Introduction to Autodesk Inventor for F1 in Schools F1 in Schools Race Car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s digital prototyping strategy
Merging Labels, Letters, and Envelopes Word 2013
Merging Labels, Letters, and Envelopes Word 2013 Merging... 1 Types of Merges... 1 The Merging Process... 2 Labels - A Page of the Same... 2 Labels - A Blank Page... 3 Creating Custom Labels... 3 Merged
Introduction to Autodesk Inventor for F1 in Schools
F1 in Schools race car Introduction to Autodesk Inventor for F1 in Schools In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital Prototyping strategy
ME 24-688 Week 4 Project 1 Assemblies and Constraints
1 Introduction to Assembly Design The following section will give an overview of bring individual components into a common environment and use various tools to assemble them. 1.1 Definition of an Assembly
Advanced Presentation Features and Animation
There are three features that you should remember as you work within PowerPoint 2007: the Microsoft Office Button, the Quick Access Toolbar, and the Ribbon. The function of these features will be more
To Begin Customize Office
To Begin Customize Office Each of us needs to set up a work environment that is comfortable and meets our individual needs. As you work with Office 2007, you may choose to modify the options that are available.
How to create a Flash banner advert in DrawPlus X2
How to create a Flash banner advert in DrawPlus X2 Open DrawPlus X2 and choose Start New: Keyframe Animation Select WebPlus 10 Flash Banner and click on Open The work area should look like the screenshot.
Microsoft Word 2010. Revising Word Documents Using Markup Tools
Microsoft Word 2010 Revising Word Documents Using Markup Tools Preface Word provides several markup tools that make document collaboration easy. Color coding, highlighting, and the ability maintain multiple
Managing Subscription Contracts
Discover the Subscription Advantage Managing Subscription Contracts Autodesk Subscription offers you a broad range of benefits to help you get the most out of your Autodesk software. This tutorial shows
Creating a Poster in Powerpoint
Creating a Poster in Powerpoint January 2013 Contents 1. Starting Powerpoint 2. Setting Size and Orientation 3. Display a Grid 5. Apply a background 7. Add text to your poster 9. Add WordArt to your poster
Autodesk Fusion 360 Badge Guide: Design an F1 in Schools Trophy
Autodesk Fusion 360 Badge Guide: Design an F1 in Schools Trophy Abstract: Gain basic understanding of creating 3D models in Fusion 360 by designing an F1 in Schools trophy. This badge may be claimed by
Animating in Inventor Studio the basics
Animating in Inventor Studio the basics This tutorial is provided at no cost to Autodesk Inventor users by B2 Design. Anyone downloading or viewing the tutorial does not have permission to copy any part
Autodesk Product Manager Tool
Autodesk Product Manager Tool A Step Guide for Conducting a Software Audit 2007 Autodesk 1 Autodesk Product Manager Installing and Conducting a Software Audit The Autodesk Product Manager (APM) utility
Pro/ENGINEER Wildfire 4.0 Basic Design
Introduction Datum features are non-solid features used during the construction of other features. The most common datum features include planes, axes, coordinate systems, and curves. Datum features do
PowerPoint 2013: Basic Skills
PowerPoint 2013: Basic Skills Information Technology September 1, 2014 1 P a g e Getting Started There are a variety of ways to start using PowerPoint software. You can click on a shortcut on your desktop
Mouse and Pointer Settings. Technical Brief
Mouse and Pointer Settings Technical Brief Avocent, the Avocent logo, DSView, AutoView, SwitchView, DSR, OSCAR and AVWorks are trademarks or registered trademarks of Avocent Corporation or its affiliates.
WebFOCUS BI Portal: S.I.M.P.L.E. as can be
WebFOCUS BI Portal: S.I.M.P.L.E. as can be Author: Matthew Lerner Company: Information Builders Presentation Abstract: This hands-on session will introduce attendees to the new WebFOCUS BI Portal. We will
Windows 10: A Beginner s Guide
Windows 10: A Beginner s Guide Copyright 2014 Conceptual Kings. All are rights reserved. This book or any portion thereof may not be reproduced or used in any manner whatsoever without the express written
How to Program a Commander or Scout to Connect to Pilot Software
How to Program a Commander or Scout to Connect to Pilot Software Commander and Scout are monitoring and control products that can transfer physical environmental conditions and alarm sensor electrical
Publication Number spse01660
Assembly reports Publication Number spse01660 Assembly reports Publication Number spse01660 Proprietary and restricted rights notice This software and related documentation are proprietary to Siemens
MICROSOFT OUTLOOK 2011 READ, SEARCH AND PRINT E-MAILS
MICROSOFT OUTLOOK 2011 READ, SEARCH AND PRINT E-MAILS Lasted Edited: 2012-07-10 1 Find the Inbox... 3 Check for New Mail... 4 Manually check for new messages... 4 Change new incoming e-mail schedule options...
Make Voice Calls and Share Documents using Skype*
Make Voice Calls and Share Documents using Skype* Intel Easy Steps 1 2012 Intel Corporation Using Skype for making Voice Calls and Sharing Documents In the previous activity Using Skype to Communicate
Creating Drawings in Pro/ENGINEER
6 Creating Drawings in Pro/ENGINEER This chapter shows you how to bring the cell phone models and the assembly you ve created into the Pro/ENGINEER Drawing mode to create a drawing. A mechanical drawing
Instructions for Formatting APA Style Papers in Microsoft Word 2010
Instructions for Formatting APA Style Papers in Microsoft Word 2010 To begin a Microsoft Word 2010 project, click on the Start bar in the lower left corner of the screen. Select All Programs and then find
PC Agent Quick Start. Open the Agent. Autonomy Connected Backup. Version 8.8. Revision 0
T E C H N I C A L N O T E Autonomy Connected Backup Version 8.8 PC Agent Quick Start Revision 0 Use this document as a quick reference for common Connected Backup PC Agent tasks. If the Agent is not on
Create a Poster Using Publisher
Contents 1. Introduction 1. Starting Publisher 2. Create a Poster Template 5. Aligning your images and text 7. Apply a background 12. Add text to your poster 14. Add pictures to your poster 17. Add graphs
Animations in Creo 3.0
Animations in Creo 3.0 ME170 Part I. Introduction & Outline Animations provide useful demonstrations and analyses of a mechanism's motion. This document will present two ways to create a motion animation
Triggers & Actions 10
Triggers & Actions 10 CHAPTER Introduction Triggers and actions are the building blocks that you can use to create interactivity and custom features. Once you understand how these building blocks work,
Roadway Plan Production
AutoCAD Civil 3D 2010 Education Curriculum Instructor Guide Unit 5: Transportation Design Lesson 5 Roadway Plan Production Overview This lesson describes how to automate the generation of plan and profile
Intermediate PowerPoint
Intermediate PowerPoint Charts and Templates By: Jim Waddell Last modified: January 2002 Topics to be covered: Creating Charts 2 Creating the chart. 2 Line Charts and Scatter Plots 4 Making a Line Chart.
PowerPoint 2007: Basics Learning Guide
PowerPoint 2007: Basics Learning Guide What s a PowerPoint Slide? PowerPoint presentations are composed of slides, just like conventional presentations. Like a 35mm film-based slide, each PowerPoint slide
Microsoft Word 2010. Quick Reference Guide. Union Institute & University
Microsoft Word 2010 Quick Reference Guide Union Institute & University Contents Using Word Help (F1)... 4 Window Contents:... 4 File tab... 4 Quick Access Toolbar... 5 Backstage View... 5 The Ribbon...
How To Write A Cq5 Authoring Manual On An Ubuntu Cq 5.2.2 (Windows) (Windows 5) (Mac) (Apple) (Amd) (Powerbook) (Html) (Web) (Font
Adobe CQ5 Authoring Basics Print Manual SFU s Content Management System SFU IT Services CMS Team ABSTRACT A summary of CQ5 Authoring Basics including: Setup and Login, CQ Interface Tour, Versioning, Uploading
Power Point 2003 Table of Contents
Power Point 2003 Table of Contents Creating a Presentation... 2 Selecting Background and Format for Slide... 3 Creating the Title Slide... 4 Adding a New Slide... 5 Types of Text for a Slide: Taken from
Autodesk Cloud Frequently Asked Questions for Customers
Autodesk Cloud Customer FAQ Autodesk Cloud Frequently Asked Questions for Customers September 27, 2011 What are web services, cloud services and cloud computing? All of these terms refer to software technology
Autodesk Software Grant for F1 in Schools Step by Step Instructions
Autodesk Software Grant for F1 in Schools Step by Step Instructions John Helfen Partnership Strategy Manager, Autodesk Education 2013 Autodesk Autodesk Software Students and Institution Student/Faculty/Mentor
Adobe Acrobat 9 Pro Accessibility Guide: Creating Accessible PDF from Microsoft Word
Adobe Acrobat 9 Pro Accessibility Guide: Creating Accessible PDF from Microsoft Word Adobe, the Adobe logo, Acrobat, Acrobat Connect, the Adobe PDF logo, Creative Suite, LiveCycle, and Reader are either
Using an Automatic Back Up for Outlook 2003 and Outlook 2007 Personal Folders
Using an Automatic Back Up for Outlook 2003 and Outlook 2007 Personal Folders Part 1 Install the Personal Folder Backup Utility Note: You should close Outlook and any other applications before installing
SpaceClaim Introduction Training Session. A SpaceClaim Support Document
SpaceClaim Introduction Training Session A SpaceClaim Support Document In this class we will walk through the basic tools used to create and modify models in SpaceClaim. Introduction We will focus on:
Outlook Email. User Guide IS TRAINING CENTER. 833 Chestnut St, Suite 600. Philadelphia, PA 19107 215-503-7500
Outlook Email User Guide IS TRAINING CENTER 833 Chestnut St, Suite 600 Philadelphia, PA 19107 215-503-7500 This page intentionally left blank. TABLE OF CONTENTS Getting Started... 3 Opening Outlook...
Software User's Guide
Software User's Guide Brother QL-series The contents of this guide and the specifications of this product are subject to change without notice. Brother reserves the right to make changes without notice
Effective Collaboration
AUTODESK BUILDING SOLUTIONS Effective Collaboration Exporting Revit Architecture Models as ACIS Solids for Use in AutoCAD MEP The intent of this paper is to explain a process by which architects using
Movie Maker 2 Beginning
Movie Maker 2 Beginning Quick Overview...3 Preparing a Folder...3 Collecting Resources...3 Pictures...4 Screen Resolution...4 Starting Windows Movie Maker...4 Which Version?...4 Windows Movie Maker 2 Window...4
Basic Microsoft Excel 2007
Basic Microsoft Excel 2007 The biggest difference between Excel 2007 and its predecessors is the new layout. All of the old functions are still there (with some new additions), but they are now located
Generative Drafting. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes
Generative Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Generative Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting
Organizing and Managing Email
Organizing and Managing Email Outlook provides several tools for managing email, including folders, rules, and categories. You can use these tools to help organize your email. Using folders Folders can
Layout Tutorial. Getting Started
Getting Started Layout Tutorial This tutorial will explain how create a layout template, send views to a layout page, then save the document in PDF format. In this tutorial you will learn about: Creating
TABLE OF CONTENTS. INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE...
Starting Guide TABLE OF CONTENTS INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE... 7 ADVANCE CONCRETE USER INTERFACE... 7 Other important
Instant Meeting Web Moderator User Guide
USER GUIDE Conferencing Instant Meeting Web Moderator User Guide Overview... 2 System Requirements... 2 Accessing Web Moderator... 2 Creating a shortcut on your desktop... 2 Web Moderator sections... 3
MET 306 Activity 6. Using Pro/MFG Milling Operations Creo 2.0. Machining a Mast Step
Using Pro/MFG Milling Operations Creo 2.0 Machining a Mast Step If the Trim option is grayed out when trimming the mill volume, Save (making sure the.asm file is going to the correct subdirectory), Exit
WHAT S NEW IN WORD 2010 & HOW TO CUSTOMIZE IT
WHAT S NEW IN WORD 2010 & HOW TO CUSTOMIZE IT The Ribbon... 2 Default Tabs... 2 Contextual Tabs... 2 Minimizing and Restoring the Ribbon... 3 Customizing the Ribbon... 3 A New Graphic Interface... 5 Live
Working with Calendars
Working with Calendars Add an Appointment or Meeting to a Calendar You can add appointments and meetings to your calendar. Appointments are those items that you schedule only for yourself. For example,
Content Author's Reference and Cookbook
Sitecore CMS 6.2 Content Author's Reference and Cookbook Rev. 091019 Sitecore CMS 6.2 Content Author's Reference and Cookbook A Conceptual Overview and Practical Guide to Using Sitecore Table of Contents
Autodesk Fusion 360: Assemblies. Overview
Overview In this module you will learn how different components can be put together to create an assembly. We will use several tools in Fusion 360 to make sure that these assemblies are constrained appropriately
Getting Started Guide. Trimble Accubid Enterprise Software
Getting Started Guide Trimble Accubid Enterprise Software Revision A August 2013 F Toronto Office Trimble Canada Ltd. 7725 Jane Street Concord, Ontario L4K 1X4 Copyright and Trademarks 2005-2013 Trimble
HHC Compensation Module Training Document
HHC Compensation Module Training Document CONTENTS 1. ICP Compensation Module Installation...3 2. Launch the compensation...6 3. Setup Survey Setup/Import Data Initial Setup...6 4. Exporting the Master
Microsoft Office PowerPoint 2013
Microsoft Office PowerPoint 2013 Navigating the PowerPoint 2013 Environment The Ribbon: The ribbon is where you will access a majority of the commands you will use to create and develop your presentation.
10.3.1.9 Lab - Configure a Windows Vista Firewall
5.0 10.3.1.9 Lab - Configure a Windows Vista Firewall Print and complete this lab. In this lab, you will explore the Windows Vista Firewall and configure some advanced settings. Recommended Equipment Step
Microsoft Access 2010 handout
Microsoft Access 2010 handout Access 2010 is a relational database program you can use to create and manage large quantities of data. You can use Access to manage anything from a home inventory to a giant
Outlook E-Mail. Step 1: Open and Configure Outlook
Outlook E-Mail Step 1: Open and Configure Outlook 1. Click the Microsoft Button in the lower left task bar 2. Select All Programs 3. Select Microsoft Office 4. Select Microsoft Outlook 5. Follow the Start
Task Card #2 SMART Board: Notebook
Task Card #2 SMART Board: Notebook Objectives: Participants will learn how to utilize the SMART Notebook. Table of Contents: Launching The SMART Notebook Page 1 Entering Text Page 1 Top Toolbar Page 2
10.3.1.10 Lab - Configure a Windows XP Firewall
5.0 10.3.1.10 Lab - Configure a Windows XP Firewall Print and complete this lab. In this lab, you will explore the Windows XP Firewall and configure some advanced settings. Recommended Equipment Step 1
Website Creator Pro Quick Reference Guide. Version: 0.5
Website Creator Pro Quick Reference Guide Version: 0.5 Contents 1. Introduction 3 2. Navigation 4 2.1. Top Bar 4 2.1.1. Tabs 4 2.1.2. Buttons 4 2.2. Website Structure Fly-Out 4 3. Usage 5 3.1. Editor 5
PEMBINA TRAILS SCHOOL DIVISION. Information Technology Department
Information Technology Department Intro to Microsoft PowerPoint 2003 INFORMATION TECHNOLOGY DEPT. Introduction to Microsoft PowerPoint 2003 Ivone B. Kordic Instructional Technology Assistant Information
Assembly Bill of Materials, R10. In This Exercise. BOM Structure. BOM Structure Parameters
Assembly Bill of Materials, R10 In This Exercise This Skill Builder demonstrates how to create and manage the structure of bill of materials in an assembly. BOM Structure BOM is an assembly database containing
Civil 3D 2009 New Features
Civil 3D 2009 New Features User Interface Workspaces and menus Menu Browser Using the large icon in the upper left corner of your screen, you can access all menus and also search for any command, recent
FTP Over SSL (FTPS) Core FTP LE. Installing Core FTP LE"
FTP Over SSL (FTPS) Gordon State College has setup FTP Over SSL (also known as FTPS ) to allow students, faculty, and staff to access resources from our Servers from off-campus using an encrypted connection.
FDOT Plans Production Tools
FDOT State Kit for AutoCAD Civil 3D Mike Racca CADD APPLICATIONS SUPPORT Florida Department of Transportation (ECSO) Email: Mike.Racca@dot.state.fl.us Phone: 850-245-1631 GENERAL Civil 3D Plan Production
Capturing Material. Section 3
Section 3 Capturing Material Duration: 60 minutes Capturing material is the process of creating media files from video or audio source material. This section describes how to capture material from different
Citrix Client Install Instructions
Citrix Client Install Instructions If you are using Citrix remotely, Information Technology Services recommends updating Citrix client to the newest version available online. You must be an administrator
WORKING DRAWINGS Shaft Support Subassembly
Start Autocad and open a NEW drawing WORKING DRAWINGS Shaft Support Subassembly Set up the layers and line types using the LAYER command Draw the following parts and save them each in a separate file BEARING
Making Visio Diagrams Come Alive with Data
Making Visio Diagrams Come Alive with Data An Information Commons Workshop Making Visio Diagrams Come Alive with Data Page Workshop Why Add Data to A Diagram? Here are comparisons of a flow chart with
What is OneDrive for Business at University of Greenwich? Accessing OneDrive from Office 365
This guide explains how to access and use the OneDrive for Business cloud based storage system and Microsoft Office Online suite of products via a web browser. What is OneDrive for Business at University
Advanced Outlook Tutorials
Advanced Outlook Tutorials Filtering: Create a filter to send email directly to a specific folder from a certain sender: 1. Right click on the sender s email. 2. Choose Rules. 3. Click on Create Rule.
Qlik Sense Cloud. Qlik Sense 2.0.4 Copyright 1993-2015 QlikTech International AB. All rights reserved.
Qlik Sense Cloud Qlik Sense 2.0.4 Copyright 1993-2015 QlikTech International AB. All rights reserved. Copyright 1993-2015 QlikTech International AB. All rights reserved. Qlik, QlikTech, Qlik Sense, QlikView,
Release Notes DAISY 4.0
2010 Release Notes DAISY 4.0 NEW FEATURES Inactivate/Reactivate accounts and patients Enhanced treatment planning AutoRemind electronic appointment confirmation Copyright 2010. DAISY is a registered trademark
JustClust User Manual
JustClust User Manual Contents 1. Installing JustClust 2. Running JustClust 3. Basic Usage of JustClust 3.1. Creating a Network 3.2. Clustering a Network 3.3. Applying a Layout 3.4. Saving and Loading
ME 24-688 Week 11 Introduction to Dynamic Simulation
The purpose of this introduction to dynamic simulation project is to explorer the dynamic simulation environment of Autodesk Inventor Professional. This environment allows you to perform rigid body dynamic
Microsoft PowerPoint 2011
Microsoft PowerPoint 2011 Starting PowerPoint... 2 Creating Slides in Your Presentation... 3 Beginning with the Title Slide... 3 Inserting a New Slide... 3 Adding an Image to a Slide... 4 Downloading Images
TUTORIAL: BOARDMAKER STUDIO START-UP
Congratulations, you ve downloaded the Boardmaker Studio trial. To be successful from the start, use this guide to learn the essential skills in Boardmaker Studio. 1 EDIT IN PLACE The most essential skill.
SimLab 3D PDF. Settings
SimLab 3D PDF Settings 3D PDF Settings PDF Settings dialog enables the user to control the exported 3D PDF file(s), from SimLab Composer and other 3D SimLab plugins. In SimLab Composer the dialog can be
Speaker Drafting. Page 1 1997 2001 DASSAULT SYSTEMES
Speaker Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Assembly Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting
Contents. Stationery Greeting Cards at a glance... 3. Stationery Greeting Cards in Mail... 4. Installing Stationery Greeting Cards...
Greeting Cards Contents Stationery Greeting Cards at a glance... 3 Stationery Greeting Cards in Mail... 4 Installing Stationery Greeting Cards... 5 Downloading & installing the app... 5 Restoring your
Symantec Enterprise Vault
Symantec Enterprise Vault Guide for Microsoft Outlook 2010 Users 9.0 Symantec Enterprise Vault: Guide for Microsoft Outlook 2010 Users The software described in this book is furnished under a license agreement
Working with Video in PowerPoint 2010
518 442-3608 Working with Video in PowerPoint 2010 Adding video to a PowerPoint presentation can be very useful. In this handout we will explore many of the program s video options. When you start PowerPoint
Section 1: Ribbon Customization
WHAT S NEW, COMMON FEATURES IN OFFICE 2010 2 Contents Section 1: Ribbon Customization... 4 Customizable Ribbon... 4 Section 2: File is back... 5 Info Tab... 5 Recent Documents Tab... 7 New Documents Tab...
MICROSOFT OUTLOOK 2011 SEND AND RESPOND TO E-MAILS
MICROSOFT OUTLOOK 2011 SEND AND RESPOND TO E-MAILS Lasted Edited: 2012-07-10 1 Send E-mail... 3 Create a new message... 3 Change the signature in the e-mail body,... 4 Change the sending out e-mail account...
Symantec Enterprise Vault
Symantec Enterprise Vault Guide for Microsoft Outlook 2010/2013 Users 10.0 Full Outlook Add-In Symantec Enterprise Vault: Guide for Microsoft Outlook 2010/2013 Users The software described in this book
Instructions for Formatting MLA Style Papers in Microsoft Word 2010
Instructions for Formatting MLA Style Papers in Microsoft Word 2010 To begin a Microsoft Word 2010 project, click on the Start bar in the lower left corner of the screen. Select All Programs and then find
Advanced Excel 10/20/2011 1
Advanced Excel Data Validation Excel has a feature called Data Validation, which will allow you to control what kind of information is typed into cells. 1. Select the cell(s) you wish to control. 2. Click
Symantec Enterprise Vault
Symantec Enterprise Vault Guide for Microsoft Outlook 2010/2013 Users 10.0 Light Outlook Add-In Symantec Enterprise Vault: Guide for Microsoft Outlook 2010/2013 Users The software described in this book
Chapter 9 Slide Shows
Impress Guide Chapter 9 Slide Shows Transitions, animations, and more Copyright This document is Copyright 2007 2013 by its contributors as listed below. You may distribute it and/or modify it under the
College of Arts & Sciences Degree Works Template Management User Guide for Advisors
College of Arts & Sciences Degree Works Template Management User Guide for Advisors Degree Works Template Management User Guide created by Emily Beard, CAS Advising, January 2016 1 Template Management
Windows Movie Maker 2012
Windows Movie Maker 2012 Open Windows Movie Maker A shortcut for Movie Maker should be on the desktop, but if it is not, you can search for the program by touching the right edge of the screen and swiping
Content Author's Reference and Cookbook
Sitecore CMS 6.5 Content Author's Reference and Cookbook Rev. 110621 Sitecore CMS 6.5 Content Author's Reference and Cookbook A Conceptual Overview and Practical Guide to Using Sitecore Table of Contents
Enhanced Formatting and Document Management. Word 2010. Unit 3 Module 3. Diocese of St. Petersburg Office of Training Training@dosp.
Enhanced Formatting and Document Management Word 2010 Unit 3 Module 3 Diocese of St. Petersburg Office of Training Training@dosp.org This Page Left Intentionally Blank Diocese of St. Petersburg 9/5/2014
Microsoft PowerPoint 2010 Handout
Microsoft PowerPoint 2010 Handout PowerPoint is a presentation software program that is part of the Microsoft Office package. This program helps you to enhance your oral presentation and keep the audience
Producing Standards Based Content with ToolBook
Producing Standards Based Content with ToolBook Contents Using ToolBook to Create Standards Based Content... 3 Installing ToolBook... 3 Creating a New ToolBook Book... 3 Modifying an Existing Question...
SOS SO S O n O lin n e lin e Bac Ba kup cku ck p u USER MANUAL
SOS Online Backup USER MANUAL HOW TO INSTALL THE SOFTWARE 1. Download the software from the website: http://www.sosonlinebackup.com/download_the_software.htm 2. Click Run to install when promoted, or alternatively,