DM 161 S-DIAS Digital Mixed Module

Transcription

1 DM 161 S-DIAS Digital Mixed Module Date of creation: Version date: Article number: E

2 Publisher: SIGMATEK GmbH & Co KG A-5112 Lamprechtshausen Tel.: 06274/4321 Fax: 06274/ Copyright 2014 SIGMATEK GmbH & Co KG Translation from German All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or distributed in any form (print, photocopy, microfilm or in any other process) without the express permission. We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur through use of this handbook.

3 S-DIAS DIGITAL MIXED MODULE DM 161 S-DIAS Digital Mixed Module DM 161 with 8 digital inputs 8 short-circuit proof digital outputs The S-DIAS DM 161 digital mixed module has eight digital inputs (+24 V/3.7 ma/5 ms) and eight short-circuit proof digital outputs (+24 V/0.5 A). The supply voltage is monitored for under voltage Page 1

4 DM 161 S-DIAS DIGITAL MIXED MODULE Contents 1 Technical Data Digital Input Specifications Digital Output Specification Electrical Requirements Voltage Monitor Miscellaneous Environmental Conditions Mechanical Dimensions Connector Layout Status LEDs Applicable Connectors Wiring Wiring Example Note Connecting Inductive Loads Mounting Addressing Page

5 S-DIAS DIGITAL MIXED MODULE DM Technical Data 1.1 Digital Input Specifications Number 8 Input voltage typically +24 V maximum +30 V Signal level low: < +8 V high: > +14 V Switching threshold Input current Input delay typically +11 V 3.7 ma at +24 V typically 5 ms 1.2 Digital Output Specification Number 8 Short-circuit proof Maximum continuous current load allowed per channel Maximum total current (all 8 outputs) Maximum braking energy of outputs (inductive load) Residual current (off) yes 0.5 A 4 A (100% of on-time) maximum 1 Joule / channel 10 µa Turn-on delay < 100 µs Turn-off delay < 150 µs 1.3 Electrical Requirements Power supply +24 V Current consumption of the +24 V supply Voltage supply on S-DIAS bus V DC corresponds to the load on the digital outputs +5 V Current consumption on S-DIAS bus (+5 V supply) typically 45 ma maximum 50 ma Page 3

6 DM 161 S-DIAS DIGITAL MIXED MODULE Page

7 S-DIAS DIGITAL MIXED MODULE DM Voltage Monitor Power supply +24 V supply voltage > 18 V (DC OK-LED lights green) 1.4 Miscellaneous Article number Hardware version 1.x Standard Approbations UL 508 (E247993) UL, cul, CE 1.5 Environmental Conditions Storage temperature C Operating temperature C Humidity EMV resistance EMC - noise generation 0-95 %, non-condensing in accordance with EN (industrial area) in accordance with EN (industrial area) Vibration resistance EN mm from Hz 1 g from Hz Shock resistance EN g Protection type EN IP Page 5

8 DM 161 S-DIAS DIGITAL MIXED MODULE 2 Mechanical Dimensions Page

9 S-DIAS DIGITAL MIXED MODULE DM Connector Layout Page 7

10 DM 161 S-DIAS DIGITAL MIXED MODULE 3.1 Status LEDs Module Status green ON module active OFF BLINKING (5 Hz) no supply available no communication User yellow ON can be set from the application OFF BLINKING (2 Hz) (e.g. the module LED can be set to blinking through the visualization so that the module is easily found in the control cabinet) BLINKING (4 Hz) Input Status green ON input ON OFF input OFF Output status yellow ON 0utput on OFF output off DC OK green ON Voltage is supplied to the output group 3.2 Applicable Connectors Connectors: X1-X5: Connectors with spring terminals (included in delivery) Connections: Stripping length: 10 mm Plug-in direction: parallel to conductor axis or to PCB Conductor cross section, solid: mm 2 Conductor cross section, stranded: mm 2 Conductor cross section AWG/kcmil: Conductor cross section stranded, with mm 2 ferrule without plastic sleeve: Conductor cross section stranded, with ferrule with plastic sleeve: mm 2 (ground for reducing d2 of the ferrule) Page

11 S-DIAS DIGITAL MIXED MODULE DM Wiring 4.1 Wiring Example Page 9

12 DM 161 S-DIAS DIGITAL MIXED MODULE 4.2 Note Up to 8 outputs are powered by a common +24 V supply. The cross section of the conductor for the +24 supply must be sufficient for the maximum total current. The outputs and can be turned off by turning off the +24 V supply voltage. Applying power to an output whose supply voltage exceeds 0.7 V is not allowed. Inductive loads must always be connected to a freewheeling diode or an RC network. This should be placed as close to the load as possible. IMPORTANT: The S-DIAS module CANNOT be connected or disconnected while voltage is applied! IMPORTANT: Le module S-Dias NE PEUT PAS être inséré ou retiré sous tension Connecting Inductive Loads Freewheeling diode coil Page

13 S-DIAS DIGITAL MIXED MODULE DM Mounting The S-DIAS modules are designed for installation into the control cabinet. To mount the modules a DIN-rail is required. The DIN rail must establish a conductive connection with the back wall of the control cabinet. The individual S-DIAS modules are mounted on the DIN rail as a block and secured with latches. The modules must be mounted horizontally (module label up) with sufficient clearance between the ventilation slots of the S-DIAS module blocks and nearby components and/or the control cabinet wall. This is necessary for optimal cooling and air circulation, so that proper function up to the maximum operating temperature is ensured Page 11

14 DM 161 S-DIAS DIGITAL MIXED MODULE Recommended minimum distances of the S-DIAS modules to the surrounding components or control cabinet wall: a, b, c distances in mm (inches) ϑ valid ambient temperature in C ( F) Page

15 S-DIAS DIGITAL MIXED MODULE DM Addressing Address (hex) Memory Size (bytes) Access Type Description Reset value r w Input register Bit 0: input 1 Bit 1: Input 2 Bit 7: input 8 Bit 8: reserved Output register Bit 0: output 1 Bit 1: output 2 Bit 7: output Page 13

16 DM 161 S-DIAS DIGITAL MIXED MODULE Documentation Changes Date Affected page(s) Chapter Note Mounting Text updated Note Added note concerning connecting the S-DIAS module while voltage is applied Applicable Connectors Added connections Miscellaneous Standard changed Electrical Requirements Graphics added Mounting Graphics distances Page