Commander Series. Commander 20A 40A Maximum Power Point Tracking Solar Charge Controller

Transcription

1 Commander Series Commander 20A 40A Maximum Power Point Tracking Solar Charge Controller E. Philadelphia St., Ontario, CA Version 2.2

2 Important Safety Instructions Please save these instructions. This manual contains important safety, installation, and operating instructions for the charge controller. The following symbols are used throughout the manual to indicate potentially dangerous conditions or important safety information. WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task. CAUTION: Indicates a critical procedure for safe and proper operation of the controller NOTE: Indicates a procedure or function that is important to the safe and proper operation of the controller. General Safety Information Read all of the instructions and cautions in the manual before beginning the installation. There are no serviceable parts for this controller. Do NOT disassemble or attempt to repair the controller. Do NOT allow water to enter the controller. Make sure all connections going into and from the controller are tight. Charge Controller Safety NEVER connect the solar panel array to the controller without a battery. Battery must be connected first. Ensure input voltage does not exceed 150 VDC to prevent permanent damage. Use the Open Circuit (Voc) to make sure the voltage does not exceed this value when connecting panels together. Battery Safety Use only sealed lead-acid, flooded, or gel batteries which must be deep cycle. Explosive battery gases may be present while charging. Be certain there is enough ventilation to release the gases. 1

3 Be careful when working with large lead acid batteries. Wear eye protection and have fresh water available in case there is contact with the battery acid. Carefully read battery manuals before operation. Do NOT let the positive (+) and negative (-) terminals of the battery touch each other. Recycle battery when it is replaced. Over-charging and excessive gas precipitation may damage the battery plates and activate material shedding on them. Too high of an equalizing charge or too long of one may cause damage. Please carefully review the specific requirements of the battery used in the system. Equalization is carried out only for non-sealed / vented/ flooded / wet cell lead acid batteries. Do NOT equalize sealed / VRLA type AGM / Gel cell batteries UNLESS permitted by battery manufacturer. WARNING: Connect battery terminals to the charge controller BEFORE connecting the solar panel(s) to the charge controller. NEVER connect solar panels to charge controller until the battery is connected. WARNING: Do NOT connect any inverters or battery charger into the load terminal of the charge controller. WARNING: Once equalization is active in the battery charging, it will not exit this stage unless there is adequate charging current from the solar panel. There should be NO load on the batteries when in equalization charging stage. 2

4 Table of Contents General Information... 4 Optional Components... 8 Identification of Parts... 9 PV Array Requirements PV Strings PV Max Power Installation Operation LED Indications Commander Protections System Status Troubleshooting Maintenance Fusing Technical Specifications Electrical Parameters Battery Charging Parameters Mechanical Parameters CMD-20: PV Power Conversion Efficiency Curves CMD-40: PV Power Conversion Efficiency Curves Dimensions

5 General Information The Commander Series MPPT charge controllers are suitable for various off-grid solar applications. It protects the battery from being over-charged by the solar modules and over-discharged by the loads. The controller features a smart tracking algorithm that maximizes the energy from the solar PV module(s) and charge the battery. At the same time, the low voltage disconnect function (LVD) will prevent the battery from over discharging. The Commander s charging process has been optimized for long battery life and improved system performance. The comprehensive self-diagnostics and electronic protection functions can prevent damage from installation mistakes or system faults. In addition, the charge controller has an RJ45 interface to allow communication with the MT- 50 meter. Key Features Automatically detect 12V or 24V DC system voltages. Innovative MPPT technology with high tracking efficiency up to 99% and peak conversion efficiency of 97% Deep cycle Sealed, Gel, and Flooded battery option ready Electronic protection: Overcharging, over-discharging, overload, and short circuit. Reverse protection: Any combination of solar module and battery, without causing damage to any component. Die-cast aluminum design allowing for natural heat dissipation RS-485 port and MT-50 Tracer Meter compatible for extra features MPPT Technology The MPPT Charge Controller utilizes Maximum Power Point Tracking technology to extract maximum power from the solar module(s). The tracking algorithm is fully automatic and does not require user adjustment. MPPT technology will track the array s maximum power point voltage (Vmp) as it varies with weather conditions, ensuring that the maximum power is harvested from the array throughout the course of the day. Current Boost In many cases, the MPPT charge controller will boost up the current in the solar system. The current does not come out of thin air. Instead, the power generated in the solar panels is the same power that is transmitted into the battery bank. Power is the product of Voltage (V) x Amperage (A). 4

6 Therefore, assuming 100% efficiency: Power In = Power Out Volts In * Amps In = Volts out * Amps out Although MPPT controllers are not 100% efficient, they are very close at about 92-95% efficient. Therefore, when the user has a solar system whose Vmp is greater than the battery bank voltage, then that potential difference is proportional to the current boost. The voltage generated at the solar module needs to be stepped down to a rate that could charge the battery in a stable fashion by which the amperage is boosted accordingly to the drop. It is entirely possible to have a solar module generate 8 amps going into the charge controller and likewise have the charge controller send 10 amps to the battery bank. This is the essence of the MPPT charge controllers and their advantage over traditional charge controllers. In traditional charge controllers, that stepped down voltage amount is wasted because the controller algorithm can only dissipate it as heat. The following demonstrates a graphical point regarding the output of MPPT technology. Current vs. Voltage (12V System) Output Power (12V System) Typical Battery Voltage Range Maximum Power Point Traditional Controller Operating Range Maximum Power Point Limiting Effectiveness Temperature is a huge enemy of solar modules. As the environmental temperature increases, the operating voltage (Vmp) is reduced and limits the power generation of the solar module. Despite the effectiveness of MPPT technology, the charging algorithm will possibly not have much to work with and therefore there is an inevitable decrease in performance. In this scenario, it would be preferred to have modules with higher nominal voltage, so that despite the drop in performance of the panel, the battery is still receiving a current boost because of the proportional drop in module voltage. 5

7 Four Charging Stages The Commander MPPT charge controller has a 4-stage battery charging algorithm for a rapid, efficient, and safe battery charging. They include: Bulk Charge, Boost Charge, Float Charge, and Equalization*. Bulk Charge: This algorithm is used for day to day charging. It uses 100% of available solar power to recharge the battery and is equivalent to constant current. In this stage the battery voltage has not yet reached constant voltage (Equalize or Boost), the controller operates in constant current mode, delivering its maximum current to the batteries (MPPT Charging) Constant Charging: When the battery reaches the constant voltage set point, the controller will start to operate in constant charging mode, where it is no longer MPPT charging. The current will drop gradually. This has two stages, equalize and boost and they are not carried out constantly in a full charge process to avoid too much gas precipitation or overheating of the battery. Boost Charge: Boost stage maintains a charge for 2 hours by default. The user can adjust the constant time and preset value of boost per their demand. 6

8 Float Charge: After the constant voltage stage, the controller will reduce the battery voltage to a float voltage set point. Once the battery is fully charged, there will be no more chemical reactions and all the charge current would turn into heat or gas. Because of this, the charge controller will reduce the voltage charge to smaller quantity, while lightly charging the battery. The purpose for this is to offset the power consumption while maintaining a full battery storage capacity. In the event that a load drawn from the battery exceeds the charge current, the controller will no longer be able to maintain the battery to a Float set point and the controller will end the float charge stage and refer back to bulk charging. Equalization: Is carried out every 28 days of the month. It is intentional overcharging of the battery for a controlled period of time. Certain types of batteries benefit from periodic equalizing charge, which can stir the electrolyte, balance battery voltage and complete chemical reaction. Equalizing charge increases the battery voltage, higher than the standard complement voltage, which gasifies the battery electrolyte. WARNING: Once equalization is active in the battery charging, it will not exit this stage unless there is adequate charging current from the solar panel. There should be NO load on the batteries when in equalization charging stage. WARNING: Over-charging and excessive gas precipitation may damage the battery plates and activate material shedding on them. Too high of equalizing charge or for too long may cause damage. Please carefully review the specific requirements of the battery used in the system. WARNING: Equalization may increase battery voltage to a level damaging to sensitive DC loads. Ensure that all load allowable input voltages are greater than the equalizing charging set point voltage. 7

9 Optional Components *The CMD20/CMD40 is shipped with the MT-50 Tracer Meter Figure 1 MT-50 Tracer Meter: The MT-50 is required to make any changes on the commander. Modify battery type, charge parameters and take advantage of this self-diagnostics meter ideal for monitoring and displaying the current solar system status information and any error indications the system might be experiencing. The meter also allows users to program loads for different time intervals. Optional components that require a separate purchase: Figure 1 Remote Temperature Sensor: This sensor measures the temperature at the battery and uses this data for very accurate temperature compensation. Accurate temperature compensation is important in ensuring proper battery charging regardless of the temperature. Figure 1 USB to RS-485 Converter Cable: This PC communication cable is needed for remote monitoring using an optional PC software. Through the software, users could customize their charge parameters and other settings. Download the PC software through Renogy s website under the Downloads section. NOTE: PC Communication requires the USB be connected at all times. Wireless capability not available. WARNING: Do NOT use a PC Ethernet cable. This can and will cause permanent damage to a computer. 8

10 Identification of Parts Key Parts Heat Sink 2. Charging LED Indicator 3. Battery LED Indicator 4. Set Button 5. Remote Temperature Sensor Port (optional accessory) 6. PV Terminals 7. Battery Terminals 8. Load Terminals 9. RS-485 Port or MT-50 Tracer Port (optional accessories)

11 PV Array Requirements PV Strings The commander is suitable for various types of PV configurations to maximize electrical energy. Configurations are dependent on the open circuit voltage (Voc) and maximum power point voltage (Vmp) located in solar panel specifications. The following table is to serve as a reference only. System Voltage 36 Cell Module (Voc < 23V) 60 Cell Module (Voc < 38V) 72 Cell Module (Voc < 46V) Max Best Max Best Max Best 12V V Note: The above parameter values are calculated under the STC conditions: Irradiance 1000W/m 2, Temperature 25 C, Air Mass 1.5 PV Max Power The Commanders have a limiting current function, where the current is limited within a range, and therefore allows battery charging at the correct value despite oversized input power. The power operation follows the following conditions: 1. PV Actual Power controller rated charge power, the controller charge battery at the actual maximum power point. 2. PV Actual Power controller rated charge power, the controller charges the battery at the rated power. WARNING: The Commander will be damaged if the PV array is 3X greater than the actual operating power of the controller. WARNING: The Commander s reverse polarity is no longer warranted if the PV array size is 1.5X greater than the rated power of the controller. 10

12 The following tables serves as the reference guide for the statements above: Model Rated Charge Current Rated Charge Power Max PV Array Power Max PV Voc Input Commander 20A 20A 12V 24V 12V 24V minimum operating environmental temperature OR Commander 40A 40A 12V 24V 12V 24V 25 C environmental temperature Installation Recommended tools to have before installation: Flathead Screwdriver Multi-Meter WARNING: Connect battery terminal wires to the charge controller FIRST then connect the solar panel(s) to the charge controller. NEVER connect solar panel to charge controller before the battery. WARNING: Do NOT connect any inverters or battery chargers into the LOAD TERMINAL of the charge controller 11

13 INVERTER BATTERY CHARGER HIGH AMP DRAWING DEVICE CAUTION: Do not over-torque or over tighten the screw terminals. This could potentially break the piece that holds the wire to the charge controller. CAUTION: Refer to the technical specifications for max wire sizes on the controller and for the maximum amperage going through wires. You are now ready to begin connecting your battery to your charge controller. Battery

14 3 Load (optional) 1 2 Solar Panels

15 MT-50 Tracer (optional) 1 2 Temperature Sensor (optional, not polarity sensitive) 1 2 Mounting Recommendations WARNING: Never install the controller in a sealed enclosure with flooded batteries. Gas can accumulate and there is a risk of explosion. 1. Choose Mounting Location place the controller on a vertical surface protected from direct sunlight, high temperatures, and water. Make sure there is good ventilation. 2. Check for Clearance verify that there is sufficient room to run wires, as well as clearance above and below the controller for ventilation. The clearance should be at least 6 inches (150mm). 3. Mark Holes 4. Drill Holes 5. Secure the charge controller 14

16 Operation The CMD-20 and CMD-40 is very simple to use. Simply connect the batteries, and the controller will automatically determine the battery voltage. If there is a load connected, use the red-orange button in front of the charge controller to manually turn the load on or off. NOTE: Refer to the Technical Specifications to make sure the device connected to the load terminal does not exceed the rated voltage and amperage limitations for this terminal. NOTE: For programmable functions, the MT-50 Tracer Meter or the PC Communication Cable is needed. Press to turn Load on or off LED Indications

17 PV Indicator (1) Green Flashing Green Solid Off BATT Indicator (2) Green Solid Green Flashing Orange Solid Red Solid Green Flashing quickly Red Flashing Status The PV system is charging the battery bank The PV system is charging the battery bank at a slow rate. Make sure panels are not shaded. Low Amperage The PV system is not charging the battery bank. PV not detected. Status Battery is normal Battery fully charged Battery under voltage warning Battery Low voltage disconnect Battery High voltage disconnect Battery is over-temperature. PV Indicator (1) BATT Indicator (2) Controller Status Green Flashing Green Flashing Off Red Flashing Orange Flashing Off Work voltage error charge controller is overtemperature Controller needs 9V minimum to turn on. Check connections NOTE: This table demonstrates controller status based on both PV and BATT indicator 16

18 Commander Protections Protection PV Array Short Circuit Behavior When PV shot circuit occurs, the controller will stop charging. Clear it to resume normal operation PV Overvoltage PV Overcurrent If the PV voltage is larger than maximum input open voltage 150VDC, PV will remain disconnected and warning until the voltage falls safely below 145V. PV voltage cannot be too high, otherwise it may damage the controller. The controller will limit the battery charging current to the maximum battery current rating. Therefore an over-sized solar array will not operate at peak power. Load Overload If the current exceeds the maximum load current rating 1.05 times, the controller will disconnect the load. Overloading must be cleared up by reducing the load and restarting the controller. Load Short Circuit Fully protected against the load wiring short-circuit. Once the load short (more than quadruple rate current), the load short protection will start automatically. After 5 automatic load reconnect attempts, the faults must be cleared by restarting the controller. PV Reverse Polarity The controller will not operate if the PV wires are switched. Wire them correctly to resume normal controller operation. Battery Reverse Polarity The controller will not operate if the battery wires are switched. Wire them correctly to resume normal controller operation. Over-Temperature If the temperature of the controller heat sink exceeds 85 O C, the controller will automatically start the protection and recover once conditions are below 75 O C 17

19 System Status Troubleshooting PV indicator Off during daylight BATT Indicator Solid orange Solid Red Flashing Red Quickly flashing green Work Mode All LED flashing (battery LED orange) All LED flashing (battery LED red) Troubleshoot Ensure that the PV wires are correctly and tightly secured inside the charge controller PV terminals. Use a multi-meter to make sure the poles are correctly connected to the charge controller. Troubleshoot Disconnect loads, if any, and let the PV modules charge the battery bank. Use a multi-meter to frequently check on any change in battery voltage to see if condition improves. This should ensure a fast charge. Otherwise, monitor the system and check to see if system improves. The controller will have cutoff the output of the battery to ensure that it charges. Make sure there are no excessive loads and give the system appropriate time and sunlight to charge. Monitor readings with a multi-meter to see if they system improves. If system does not charge, then the user must find another means for charging battery since it is too low for the controller to register. Battery is over-temperature and must be secured in a cooler location. Disconnect PV panel(s), then disconnect the battery before changing the battery s location to a cooler area. The battery voltage is higher than the over voltage disconnect. Use a multi-meter to check the battery voltage to determine whether it is too high. Then disconnect and reconnect the PV modules. Troubleshoot The temperature of the controller is too high and is probably exceeding 85 o C. The controller will automatically cut the input and output of the circuit. Once the controller registers a lower temperature, it will resume functioning normally. This indicates a system voltage error. Check whether the battery voltage matches the controller s working voltage. If correct, disconnect and reconnect all connections. Solar modules are first when disconnecting and battery is first when reconnecting. 18

20 Maintenance WARNING: Risk of Electric Shock! Make sure that all power is turned off before touching the terminals on the charge controller. For best controller performance, it is recommended that these tasks be performed from time to time. 1. Check that controller is mounted in a clean, dry, and ventilated area. 2. Check wiring going into the charge controller and make sure there is no wire damage or wear. 3. Tighten all terminals and inspect any loose, broken, or burnt up connections. 4. Make sure LED readings are consistent. Take necessary corrective action. 5. Check to make sure none of the terminals have any corrosion, insulation damage, high temperature, or any burnt/discoloration marks. Fusing Fusing is a recommended in PV systems to provide a safety measure for connections going from panel to controller and controller to battery. Remember to always use the recommended wire gauge size based on the PV system and the controller. NEC Maximum Current for different Copper Wire Sizes AWG Max. 18A 25A 30A 40A 55A 75A 95A 130A 170A Current Note: The NEC code requires the overcurrent protection shall not exceed 15A for 14AWG, 20A for 12 AWG, and 30A for 10AWG copper wire. Fuse from Controller to Battery Controller to Battery Fuse = Current Rating of Charge Controller Ex. 20A MPPT CC = 20A fuse from Controller to Battery Fuse from Solar Panel(s) to Controller Ex. 200W; 2 X 100 W panels **Utilize 1.56 Sizing Factor (SF) NOTE: Different safety factors could be used. The purpose is to oversize. Series: Total Amperage = I sc1 = I sc2 * SF = 5.75A * 1.56 = 8.97 Fuse = 9A fuse Parallel Total Amperage = (I sc1 + I sc2) * SF (5.75A A) * 1.56 = Fuse = 18A fuse 19

21 Technical Specifications Electrical Parameters Model CMD-20 CMD-40 Nominal system voltage 12V/24V Auto Recognition Rated Battery Current 20A 40A Rated Load Current 20A 20A Max. PV Input Short Current 25A 50A Battery Voltage Range 8V-32V Max Solar Input Voltage 150 VDC Max. Solar Input Power 260W 520W 520W 1040W Self-Consumption 12V 24V Grounding Negative Charge circuit voltage drop 0.26V Discharge circuit voltage drop 0.15V Temp. Compensation -3mV/ C/2V (default) Communication RSJ45 Battery Charging Parameters Battery GEL SEALED FLOODED High Voltage Disconnect 16 V 16 V 16 V Charging Limit Voltage 15 V 15 V 15 V Over Voltage Reconnect 15 V 15 V 15 V Equalization Voltage V 14.8 V Boost Voltage 14.2 V 14.4 V 14.6 V Float Voltage 13.8 V 13.8 V 13.8 V Boost Return Voltage 13.2 V 13.2 V 13.2 V Low Voltage Reconnect 12.6 V 12.6 V 12.6 V Under Voltage Recover 12.2 V 12.2 V 12.2 V Under Voltage Warning 12 V 12 V 12 V Low Voltage Disconnect 11.1 V 11.1 V 11.1 V Discharging Limit 10.6 V 10.6 V 10.6 V Voltage Equalization Duration hours 2 hours Boost Duration 2 hours 2 hours 2 hours **Parameters are multiplied by 2 for 24V systems. 20

22 Environment Parameters Model CMD-20 CMD-40 Working -35 C to +55 C Temperature Storage -35 C to +80 C Temperature Rated Load Current 10% to 90% NC Humidity Range 95% (NC) Enclosure IP30 Altitude < 3000 Mechanical Parameters Model CMD-20 CMD-40 Overall Dimension x x 56mm 8.52 x 5.61 x 2.20in x x 63.5mm x 7.19 x 2.50in Mounting Oval 7.66 x 4.70mm 0.30 x 0.18in Max Terminal Size 10mm 2 25mm 2 Net Weight 8 AWG 1.5 kg 3.3 lb. 4 AWG 2.9 kg 6.39 lb. 21

23 CMD-20: PV Power Conversion Efficiency Curves Illumination Intensity: 1000W/ m 2 Temp 25 o C 22

24 CMD-40: PV Power Conversion Efficiency Curves Illumination Intensity: 1000W/ m 2 Temp 25 o C 23

25 Dimensions CMD-20 NOTE: Dimensions in millimeters (mm) 24

26 CMD-40 NOTE: Dimensions in millimeters (mm) Renogy reserves the right to change the contents of this manual without notice. 25 Revision: 9/23/2016