First Stage Compact Twin Stage Compact Second Stage Second Stage High Pressure Industrial. Industrial valves and regulators with 10 years warranty

Transcription

1 RegO Regulators 2011 First Stage Compact Twin Stage Compact Second Stage Second Stage High Industrial Industrial valves and regulators with 10 years warranty The expected service life of a ECII/REGO regulator (excluding single stage) manufactured after 1995 is 25 years on condition that all of our recommendations are followed.

2 Instructions Do You Care About What s In Your Propane Regulator? WE DO. And we know how important it is to select the highest quality components from suppliers you know and trust. Suppliers who are not always the cheapest but are always the best. Together with our own high-end production facilities we are able to keep supplying you the best-built LPG regulators. We will provide 10 years warranty on all REGO Products (terms and conditions apply) Page 2 Page 3

3 Instructions Page 4 Instructions Page 5

4 Instructions Page 6 Instructions Page 7

5 Instructions Page 8 Instructions Page 9

6 RegO Compact First Stage Regulators LV3403TR LV3403TR RegO Compact First Stage Regulators LV3403VR LV3403VR Ideal for use as a first stage regulator on any domestic LPG installations requiring up to 32 kg/h per hour. The regulator is factory set to reduce container pressure to an intermediate pressure of approximately 0,7 bar. Ideal for use as a first stage regulator on any domestic LPG installations requiring up to 45 kg/h per hour. The regulator is factory set to reduce container pressure to an intermediate pressure of approximately 1,5 bar. Compact design can be connected to a service valve using either a POL adapter or a RegO Products pigtail. Large threaded 3/8 F.NPT bonnet vent can be easily piped-away underground installations without the need of glue kits or extra adapters. Non adjustable. Large flow orifice resists freeze-ups due to water concentration in LPG vapour Design provides for good flow regulation at both high and low container pressures. Built in relief valve and travel stop comply with NFPA 58 over pressure requirements. Incorporates 1/8 F.NPT downstream pressure tap for an easy inline check of the regulator s delivery pressure. Moulded diaphragm provides an o-ring type seal between the body and bonnet. Body and bonnet are assembled in the USA using the unique, patented RegUlok seal system. Fully painted in brilliant red for complete corrosion protection. Mounting bracket available as an accessory: part number Body Bonnet Spring Seat Disc Diaphragm NEW Non freezing regulator in all conditions Zinc Zinc Steel Resilient Rubber Integrated Fabric and Synthetic Rubber Compact design can be connected to a service valve using either a POL adapter or a RegO Products pigtail. Large threaded 3/8 F.NPT bonnet vent can be easily piped-away underground installations without the need of glue kits or extra adapters. Non adjustable. Large flow orifice resists freeze-ups due to water concentration in LPG vapour Design provides for good flow regulation at both high and low container pressures. Built in relief valve and travel stop comply with NFPA 58 over pressure requirements. Incorporates 1/8 F.NPT downstream pressure tap for an easy inline check of the regulator s delivery pressure. Moulded diaphragm provides an o-ring type seal between the body and bonnet. Body and bonnet are assembled in the USA using the unique, patented RegUlok seal system. Fully painted in brilliant red for complete corrosion protection. Mounting bracket available as an accessory: part number Body Bonnet Spring Seat Disc Diaphragm NEW Non freezing regulator in all conditions Zinc Zinc Steel Resilient Rubber Integrated Fabric and Synthetic Rubber Vapour LV3403TR ¼ F.NPT ½ F.NPT 6,3 mm 0,7 bar Over 32 kg/h LV3403TRV9 ¼ F.NPT ½ F.NPT 6,3 mm 0,7 bar Opposite Gauge port 32 kg/h LV3403UR ¼ F.NPT ½ F.NPT 6,3 mm 1 bar Over 40 kg/h Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV3403TR series are UL approved. Vapour LV3403VR ¼ F.NPT ½ F.NPT 6,3 mm 1,5 bar Over 45 kg/h LV3403VR9 ¼ F.NPT ½ F.NPT 6,3 mm 1,5 bar Opposite Gauge port 45 kg/h Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV3403VR series are UL approved. Page 10 Page 11

7 RegO Compact First Stage Regulators LV3403TRH (L) Series with BSP Threads LV3403TRH (L) Series Ideal for use as a first stage regulator on any domestic LPG installations requiring up to 45 kg/h per hour. The regulator is factory set to reduce container pressure to an intermediate pressure of approximately 0,45 or 1,5 bar. Compact design can be connected to a service valve using either a POL adapter or a RegO Products pigtail. Large threaded 3/8 F.NPT bonnet vent can be easily piped-away underground installations without the need of glue kits or extra adapters. Non adjustable. Large flow orifice resists freeze-ups due to water concentration in LPG vapour Design provides for good flow regulation at both high and low container pressures. Built in relief valve and travel stop comply with NFPA 58 over pressure requirements. Incorporates 1/8 F.NPT downstream pressure tap for an easy inline check of the regulator s delivery pressure. Moulded diaphragm provides an o-ring type seal between the body and bonnet. Body and bonnet are assembled in the USA using the unique, patented RegUlok seal system. Fully painted in brilliant red for complete corrosion protection. Mounting bracket available as an accessory: part number Body Bonnet Spring Seat Disc Diaphragm NEW Zinc Zinc Steel Resilient Rubber Integrated Fabric and Synthetic Rubber Non freezing regulator in all conditions Vapour LV3403TRH ¼ F-BSP ½ F-BSP 6,3 mm 1,5 bar Over 45 kg/h LV3403TRHV9 ¼ F-BSP ½ F-BSP 6,3 mm 1,5 bar Opposite Gauge port 45 kg/h LV3403TRL ¼ F-BSP ½ F-BSP 6,3 mm 0,45 bar Over 45 kg/h LV3403TRLV9 ¼ F-BSP ½ F-BSP 6,3 mm 0,45 bar Opposite Gauge port 45 kg/h Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. RegO New 7525B34 Twin Stage Automatic Changeover Regulator for LP-Gas 7525B34 This combination automatic change-over /two stage regulator is suitable for homes, mobile homes, cottages, construction and other portable installations utilizing two or more cylinders. Empty containers may be replaced without interrupting customer s gas service. Automatic changeover switches from service to reserve cylinder automatically without interrupting gas service. With 1 bar inlet pressure, the regulator is designed to not pass more than 137 mbar downstream with the seat disc removed. Incorporates a integral relief valve on second stage. Unique bonnet vent profile on second stage minimizes vent freeze over when properly installed. Compact design saves space allows for easy installation. Allows reserve cylinder to supplement the flow of gas from the service cylinder during extreme load or severe cold conditions. Indicator gauge and changeover knob are integral to the first stage. Second stage pressure tap plug can be removed with a 3/16 hex Allen wrench. 7525B34 Kit Number ¼ Inverted Flare Automatic Changeover Regulator ½ F.NPT Factory Delivery 28 6,8 bar * Maximum flow based on 0,7 bar 23 mbar delivery pressure Body First Stage Bonnet First Stage Bonnet First Stage Body Second Stage Bonnet Second Stage Diaphragms Springs Valve Discs 2nd Stage 2nd Stage** Vapour * mbar 8,4 kg/h* Pigtails Included-2 Int. Fabric & Synthetic Rubber Steel & Stainless Steel Resilient Rubber Bracket Included Vapour Propane 5726B B34 ¼ Inverted 912FA20 ½ F.NPT ,4 kg/h 5727B B34 Flare 912FS20 Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. Page 12 Page 13

8 RegO LV404B Series Special Purpose LP-Gas Compact Twin-Stage Regulators RegO New Compact Twin Stage Regulators for LP-Gas LV404B34 & LV404B39 Series LV404B Series Compact two-stage regulator is designed to reduce container pressure up to 17.2 bar down to a pressure between millibar; the actual adjustable pressure range is specified in the table below. Ideal for use on smaller LPG installations. Body First Stage Body Second Stage Bonnets Diaphragms Int. Fabric & Synthetic Rubber Springs Steel Valve Discs Resilient Rubber LV404B4 LV404B34 & LV404B39 Series The compact twin-stage regulator is designed to reduce container pressure down to 28 mbar. delivery pressure. It is ideal for on site container applications such as homes, mobile homes and cottages for average domestic service; including small ASME tanks and pound DOT cylinders. Body First Stage Bonnet First Stage (LV404B34) Bonnet First Stage (LV404B39) Brass Body Second Stage Bonnet Second Stage Diaphragms Int. Fabric & Synth. Rubber Springs Steel & Stainless Steel Valve Discs Resilient Rubber Large vent helps prevent vent blockage, the second stage regulator bonnet is tapped for 3/8 F.NPT for vent piping, the high pressure regulator is tapped with 1/8 F.NPT for vent piping. With 1bar inlet pressure, the regulator is designed to not pass more than 137 mbar downstream with the seat disc removed. Incorporates a integral relief valve on second stage. Unique bonnet vent profile minimizes vent freeze over when properly installed. Compact design saves space allows for easy installation especially under container hoods with collars Built in pressure taps 1/8 F.NPT on both high pressure regulator inlet and downstream side of the second stage regulator Plugs can be removed with a 3/16 hex Allen wrench Select brown finish. Inches Inches 7 bar Adj. mbar Vapour LV404B34 LV404B39 LV404B4 LV404B46 LV404B9 LV404B96 LV404B4H20 LV404B46H20 ¼ F-NPT F.POL ¼ F-NPT ½ F-NPT ¾ F-NPT ½ F-NPT ¾ F-NPT ½ F-NPT ¾ F-NPT 1st Stage 2nd Stage 28 mbar mbar Down 11 kg/h 28 mbar mbar Down 11 kg/h 50 mbar mbar Down 11 kg/h Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV404B series are UL approved. Part Number Factory Delivery 2nd Stage 1st Stage** 2nd Stage** Vapour * LV404B34 ¼ F.NPT 28 mbar Rear LV404B39 F.POL 6, ½ 6,8 9,4 kg/h LV404B34V9 ¼ F.NPT mm mbar bar Left 9:00 LV40439V9 F.POL * Maximum flow based on 0,7 bar 23 mbar delivery pressure ** Other vent positions available upon request Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. Page 14 Page 15

9 RegO Compact Second Stage Regulators LV3403B4 The LV3403B4 is designed to reduce first stage pressure of 0.35 to 1.5 bar down to burner pressure normally 28 mbar. Designed as a second stage regulator for smaller applications with flow requirements up to 9.6 kg/h, they are ideal for homes, mobile homes, and cottages. Large vent helps prevent vent blockage, it is tapped for 3/8 F.NPT for vent piping. With 1.03 bar inlet pressure, the regulator is designed to not pass more than.14 bar downstream with the seat disc removed. Incorporates a integral relief valve Unique bonnet vent profile minimizes vent freeze over when properly installed. Design provides for good flow regulation at both high and low container pressures. Compact design saves space. Built in pressure taps 1/8 F.NPT on both regulator inlet and downstream side of the regulator. Plugs can be removed with a 3/16 hex Allen wrench. Select brown finish. Body & Bonnet Nozzle Brass Spring Steel Valve Seat Disc Resilient Rubber mm Downstream Tap Tap 1/8 F.NPT NEW mm Straight Through Design Vapour LV3403B4 ½ F.NPT ½ F.NPT 6,3 mm 28 mbar mbar 9,6 kg/h LV3403B4V3 ½ F.NPT ½ F.NPT 6,3 mm 28 mbar mbar 3 o clock 9,6 kg/h LV3403B4V0 ½ F.NPT ½ F.NPT 6,3 mm 28 mbar mbar 9,6 kg/h LV3403B4V9 ½ F.NPT ½ F.NPT 6,3 mm 28 mbar mbar 9 o clock 9,6 kg/h Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV3403B series are UL approved mm RegO Low Second Stage Regulators LV4403B LV4403B Series Designed to reduce first stage pressure of 0,35 to 1,4 bar down to burner pressure, normally 28 mbar. Ideal for medium commercial installations, multiple cylinder installations and normal domestic loads. Backmount Design Mounts directly to house line piping. Eliminates need for union joints, elbows, and mounting brackets. Quick and easy to install. Body Bonnet Nozzle Brass Spring Steel Valve Seat Disc Resilient Rubber ** LV4403B4 ½ F. NPT ½ F. NPT 3,5 mm 28 mbar mbar Over 20 kg/h LV4403B46 ½ F. NPT ¾ F. NPT 3,5 mm 28 mbar mbar Over 20 kg/h LV4403B46R* ½ F. NPT ¾ F. NPT 3,5 mm 28 mbar mbar Over 20 kg/h LV4403B66 ¾ F. NPT ¾ F. NPT 3,5mm 28 mbar mbar Over 20 kg/h LV4403B66R* ¾ F. NPT ¾ F. NPT 3,5 mm 28 mbar mbar Over 20 kg/h * Backmount design. ** Maximum flow based on 0,7 bar inlet and 23 mbar delivery pressure. Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV4403B Series are UL approved. Page 16 Page 17

10 RegO Low Second Stage Regulators LV4403H Series RegO Low Second Stage Regulators LV4403K46 Series Designed to reduce first stage pressure of 0.35 to 1.5 bar down to burner pressure, normally 36 mbar. Ideal for medium commercial installations, multiple cylinder installations and normal domestic loads. Large vent helps prevent blockage and has ¾ F.NPT for vent piping. With 1 bar inlet pressure, regulator is designed to not pass more then 138 mbar with the seat disc removed. Incorporates integral relief valve Replaceable valve orifice and valve seat disc. Unique bonnet vent profile minimizes vent freeze over when properly installed. Large moulded diaphragm is extra sensitive to pressure changes. Built in pressure tap has plugged 1/8 F.NPT outlet. Plug can be removed with a 3/16 hex allen wrench. Select brown finish. Length of the Regulator 18 cm Height of the Regulator 11,8 cm Length between the bracket screws 11,4 cm Body Bonnet Nozzle Brass Spring Steel Valve Seat Disc Resilient Rubber Designed to reduce first stage pressure 0.35 to 1.5 bar down to appliance pressure nominal 29 mbar, the adjustment range is specified in the table below. Ideal for medium commercial installations, multiple cylinder installations and normal domestic loads. Body Bonnet Nozzle Brass Spring Steel Valve Seat Disc Resilient 0.7 bar inlet Approximat LV4403H222 ¼ F.NPT ½ F.NPT 3,5 mm 50mbar mbar Over inlet 14 kg/h LV4403H414 ½ F.NPT ½ F.NPT 3,5 mm 36mbar mbar Over inlet 14 kg/h LV4403H420 ½ F.NPT ½ F.NPT 3,5 mm 50mbar mbar Over inlet 14 kg/h LV4403H4614 ½ F.NPT ¾ F.NPT 3,5 mm 36mbar mbar Over inlet 14 kg/h LV4403H4620 ½ F.NPT ¾ F.NPT 3,5 mm 50mbar mbar Over inlet 14 kg/h LV4403H6614 ¾ F.NPT ¾ F.NPT 3,5 mm 36mbar mbar Over inlet 14 kg/h LV4403K46 ½ F. BSP ¾ F-BSP 3,5 mm 30 mbar mbar 17 kg/h LV4403K46V9 ½ F. BSP ¾ F-BSP 3,5 mm 30 mbar mbar 9 o clock 17 kg/h Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV4403H Series are UL approved. Page 18 Page 19

11 RegO Low Second Stage Regulators LV5503B Series Designed to reduce first stage pressure of 0,35 to 1,4 bar down to burner pressure, normally 28 mbar. Ideal for larger commercial and industrial applications. RegO Low Second Stage Regulators LV5503H Series Designed to reduce first stage pressure 5-20 PSIG ( bar) down to a pressure higher than 11 W.C (28 mbar), the actual pressure setting is specified in the table below. Ideal for medium commercial installations, multiple cylinder installations and normal domestic loads. Body Bonnet Nozzle Brass Spring Steel Valve Seat Disc Resilient Rubber Body Bonnet Nozzle Brass Spring Steel Valve Seat Disc Resilient Rubber LV5503B4 ½ F. NPT ¾ F. NPT 6,3 mm 28 mbar mbar Over 35 kg/h LV5503B6 ¾ F. NPT ¾ F. NPT 6,3 mm 28 mbar mbar Over 35 kg/h LV5503B8 ¾ F. NPT 1 F. NPT 7 mm 28 mbar mbar Over 50 kg/h connection 0,7 bar LV5503H414 ½ F. NPT ¾ F. NPT 6,3 mm 35 mbar mbar Over 35 kg/h LV5503H614 ¾ F. NPT ¾ F. NPT 6,3 mm 40 mbar mbar Over 35 kg/h LV5503H620 ¾ F. NPT ¾ F. NPT 6,3 mm 50 mbar mbar Over 35 kg/h LV5503H620V ¾ F. NPT ¾ F. NPT 6,3 mm 50 mbar mbar Over 35 kg/h LV5503H640 ¾ F. NPT ¾ F. NPT 6,3 mm 100 mbar mbar Over 35 kg/h LV5503H640V ¾ F. NPT ¾ F. NPT 6,3 mm 100 mbar mbar Over 35 kg/h LV5503H814 ¾ F. NPT 1 F. NPT 7 mm 35 mbar mbar Over 50 kg/h LV5503H820 ¾ F. NPT 1 F. NPT 7 mm 50 mbar mbar Over 50 kg/h LV5503H840 ¾ F. NPT 1 F. NPT 7 mm 100 mbar mbar Over 50 kg/h Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. LV5503 series being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use, and are therefore not marked CE. LV5503B Series are UL approved. Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV5503H Series are UL approved. Page 20 Page 21

12 RegO Large Second Stage Regulators LV6503B Series LV6503B Series Designed to reduce first stage pressure of 0,35 to 1,4 bar down to burner pressure, normally 28 mbar. Ideal for larger commercial and industrial applications. Tee style inlet and outlet connections - made from ductile iron Incorporate integral large 2 F.NPT relief vents Built in pressure taps for both inlet and outlet pressure Full capacity relief at 10 psig inlet will keep the down stream preessure at less than 2 PSIG per NFPA 58 RegO High Industrial Regulators 597 Series 597 Series Designed to reduce LP-Gas container pressure down to between 0.1 bar and 7,0 bar. Ideal for liquid or vapour service, they can be used in a variety of applications including salamander heaters, weed burning torches, fish cookers, tar pot heaters, and other industrial type services. Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. 597 series are UL approved Body Body Bonnet Ductile Iron Cast Aluminium Cast Aluminium Body Zinc Bonnet Zinc Springs Steel Valve Seat Discs Resilient Rubber Adjusting Screw Brass LV6503B14 1 ½ F. NPT 1 ½ F. NPT 16 mm 28 mbar mbar kg/h LV6503B16 2 F. NPT 2 F. NPT 16 mm 28 mbar mbar kg/h Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. LV6503B Series are CE marked. LV6503B Series are UL approved. Different springs for different settings available. Method Recommended Delivery range in bar Determined at Set pressure of bar * * Set pressure established at 7,0 bar inlet and a flow of 5,0 kg/h ** determined at actual delivery pressure 20% less than set pressure with inlet pressure 1,4 bar higher than the set pressure Propane ** 597FA Tee Handle ¼ F.NPT ¼ F.NPT 0,1 1,0 0,7 37 kg/h 597FB Tee Handle ¼ F.NPT ¼ F.NPT 0,7 2,0 1,4 63 kg/h 597FC Tee Handle ¼ F.NPT ¼ F.NPT 1,4 3,0 2,0 73 kg/h 597FD Tee Handle ¼ F.NPT ¼ F.NPT 2,8 7,0 2,8 94 kg/h Page 22 Page 23

13 1580 Series High Industrial / Commercial Regulators 1580 Series Designed to reduce LP-Gas and anhydrous ammonia container pressure to between 0,2 and 8,6 bar. Precision-built with capacities of several hundreds kilogram LP-Gas per hour. The 1580V series is perfect for such big, tough jobs as crop dryers, asphalt batch mixing plants, road building tar wagons, heat treating and other large industrial and commercial loads. It s also ideal as first stage regulator in large multiple operations. The AA1580 series is ideal for use in anhydrous ammonia applications. such as blue print machines and heat treating. Part Number Service Method & Recommended Delivery Width (A) Height (B,max) * Set pressure is established with 7 bar inlet pressure and a flow of 10,5 kg propane / hour for 1580V series, 2,5 m³/h for AA1582M Series and 5 m³/h for AA1584V and AA1586V Series ** Capacities determined at actual delivery pressure 20% less than set pressure with inlet pressure 1,4 bar higher then set pressure. NOTE: Care must be taken to prevent re-liquification of propane at normal temperatures by heat tracing or other effective means. Use a relief valve upstream or down stream of these regulators is recommended in accordance with NFPA 58 Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. 1580M series are UL approved. Determined at Set * ** AA1582MW NH³ T-Handle ¼" F.NPT 0,2-1,7 bar 56 mm 105 mm 1,4 bar 60 m³/h NH³ AA1582MK NH³ Hex Head ¼" F.NPT 0,2-1,7 bar 56 mm 105 mm 1,4 bar 60 m³/h NH³ AA1582ML NH³ T-Handle ¼" F.NPT 1,4-3,5 bar 56 mm 105mm 2,1 bar 68 m³/h NH³ AA1582MH NH³ T-Handle ¼" F.NPT 3,1-8,6 bar 56 mm 105 mm 4,1 bar 74 m³/h NH³ 1584VN LP-Gas T-Handle ½" F.NPT 0,2-2,1 bar 75 mm 124 mm 1,4 bar 147 kg/h Propane 1584VL LP-Gas T-Handle ½" F.NPT 1,7-3,5 bar 75mm 124 mm 2,1 bar 158 kg/h Propane 1584VH LP-Gas T-Handle ½" F.NPT 3,1-8,6 bar 75 mm 124 mm 4,1 bar 168 kg/h Propane AA1584VW NH³ T-Handle ½" F.NPT 0,2-1,7 bar 75 mm 124 mm 1,4 bar 127 m³/h NH³ AA1584VL NH³ T-Handle ½" F.NPT 1,4-3,5 bar 75 mm 124 mm 2,1 bar 136 m³/h NH³ AA1584VH NH³ T-Handle ½" F.NPT 3,1-8,6 bar 75 mm 124 mm 4,1 bar 144 m³/h NH³ 1586VN LP-Gas T-Handle ¾" F.NPT 0,2-2,1 bar 89 mm 178 mm 1,4 bar 230 kg/h Propane 1586VL LP-Gas T-Handle ¾" F.NPT 1,7-3,5 bar 89 mm 178 mm 2,1 bar 250 kg/h Propane 1586VH LP-Gas T-Handle ¾" F.NPT 3,1-8,6 bar 89 mm 178 mm 4,1 bar 295 kg/h Propane AA1586VW NH³ T-Handle ¾" F.NPT 0,2-1,7 bar 89 mm 178 mm 1,4 bar 198 m³/h NH³ AA1586VL NH³ T-Handle ¾" F.NPT 1,4-3,5 bar 89 mm 178 mm 2,1 bar 218 m³/h NH³ AA1586VH NH³ T-Handle ¾" F.NPT 3,1-8,6 bar 89 mm 178 mm 4,1 bar 252 m³/h NH³ 1588VN LP-Gas T-Handle 1 " F.NPT 0,2-2,1 bar 89 mm 178 mm 1,4 bar 230 kg/h Propane 1588VL LP-Gas T-Handle 1 " F.NPT 1,7-3,5 bar 89 mm 178 mm 2,1 bar 250 kg/h Propane 1588VH LP-Gas T-Handle 1 " F.NPT 3,1-8,6 bar 89 mm 178 mm 4,1 bar 295 kg/h Propane RegO High /High Temperature Industrial/Commercial Regulators X1584V, X1586V, X1588V Series Designed to reduce LP-Gas container pressures between 0,2 and 8,6 bar. Ideal for crop drying, heat treating, asphalt batch mixing and other large industrial and commercial load applications such as vaporizers that utilize high temperature LP-Gas or high temperature atmosphere under conditions up to 148,8 C. Also ideal as a first stage regulator in large multiple operations. Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. 1580V series are UL approved. Body Zinc Bonnet Zinc Springs Steel Valve Seat Discs Resilient Rubber Adjusting Screw Brass Part Number Service Method & Recommended Delivery range in bar * Set pressure is established with 7 bar inlet pressure and a flow of 10,5 kg propane / hour for X1580V series. ** Capacities determined at actual delivery pressure 20% less than set pressure with inlet pressure 1,4 bar higher then set pressure. NOTE: Care must be taken to prevent re-liquification of propane at normal temperatures by heat tracing or other effective means. Use a relief valve upstream or down stream of these regulators is recommended in accordance with NFPA 58 Width (A) Height (B, max) Determined at Set pressure in bar * screen protects seal from foreign material. It is easily removed for cleaning. The RegO Regulator especially for vaporiser installations kg/h Propane** X1584VN LP-Gas T-Handle ½ F.NPT 0,2 2,1 1,4 147 X1584VL LP-Gas T-Handle ½ F.NPT 1,7 3,5 75 mm 124 mm 2,1 158 X1586VN LP-Gas T-Handle ¾ F.NPT 0,2 2,1 1,4 230 X1586VL LP-Gas T-Handle ¾ F.NPT 1,7 3,5 89 mm 178 mm 2,1 250 X1588VN LP-Gas T-Handle 1 F.NPT 0,2 2,1 1,4 230 X1588VL LP-Gas T-Handle 1 F.NPT 1,7 3,5 89 mm 178 mm 2,1 250 REGO GmbH - Distribution Center Europe Industriestrasse 9, D Gladenbach, Germany Phone +49 (0) , Fax info@rego-europe.de Page 24 Page 25

14 RegO Low Service Regulators for Natural Gas LV4403F66RA Series Designed to reduce inlet pressure of from 1-3 bar to a delivery pressure of 17.4 mbar. 90 degree right angle inlet to outlet connection for standard meter installations Large vent helps prevent blockage and has a ¾ F.NPT for vent piping. Straight-line valve closure reduces wear on seat disc. Unique bonnet vent profile minimizes vent freeze over when properly installed. Large molded diaphragm is extra sensitive to pressure changes. Built in pressure tap has plugged 1/8 outlet. Plug can be removed with a 3/16 Allen wrench. Select Brown Finish Body Bonnet Nozzle Brass Spring Steel Valve Seat Disc Integrated Fabric & Synthetic Rubber mbar LV4403F66RA Series mbar mbar 3.0 bar 2.5 bar 2.0 bar 1.5 bar 1 bar Set point 1.5 bar 17.4 mbar delivery pressure Cubic Meters/Hr Natural Gas Vapour m³/h Natural Gas LV4403F66RA ¾ F.NPT ¾ F.NPT 3/ Over inlet 30.5 LV4403F66RAB ¾ F.NPT ¾ F.NPT 3/ Over inlet 30.5 LV4403F66RA9 ¾ F.NPT ¾ F.NPT 3/ : Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. 25 years of expected service life of a ECII/ RegO regulator (excluding single stage) on condition that all of our recommendations are followed 10 years warranty on all RegO products (terms and conditions apply) RegO Compact First Stage Regulators LV3403 Series For any domestic LPG installations requiring up to 32/45 kg/h. Non freezing regulator in all conditions gauge available as an accessory High performance and security in extreme conditions RegO High Industrial/ Commercial Regulators 1580 Series Designed to reduce LP-Gas and anhydrous ammonia container pressure to between 0,2 and 8,6 bar. This is what USA made RegO regulators give their users RegO Special Purpose LP-Gas Compact Twin- Stage Regulator LV404 Series Designed to reduce container pressure up to 17,2 bar down to burner pressure RegO Low Second Stage Regulator LV4403/LV5503 Series Designed to reduce first stage pressure of 0,35 to 1,5 bar down to burner pressure RegO products are PED approved Page 26 Page 27

15 LPGas Products of excellence from the world s leading manufacturer B Our products are CE or B marked as conforming to: PED Equipment Directive 97/23/EC TPED Transportable Equipment Directive 1999/36/EC ISO 9001 Certified REGO GmbH is certified according to ISO 9001 by TÜV Germany. All made with pride in USA REGO GmbH - Distribution Center Europe Industriestrasse 9, D Gladenbach, Germany Phone +49 (0) , Fax info@rego-europe.de Page