Using the Lantronix UDS-1100 Device Server Application Note #20

Transcription

1 5 Gould Road, PO Box 2155 New London, NH Voice: (603) Overview Using the Lantronix UDS-1100 Device Server Application Note #20 The Lantronix UDS-1100 Device Server is device for interfacing serial port equipped hardware (either RS-232 or RS-485) onto Ethernet networks. These instructions will detail how to configure and use the UDS-1100 with various equipment including Campbell Scientific MCU s and Leica Total Stations. The UDS-1100 replaces the Lantronix UDS- 10. Wiring Various wiring conventions are shown in the table below. UDS-1100 DB25F Description In/Out Leica TPS RS-232 DB9M CR10X CSI I/O DB9M CR2xx CR800/CR1000 RS-232 DB9M RESmith RS-485 Adaptor 2 Transmit Data (TX) In 2 (White) 9 (White) 2 (White) 3 Receive Data (RX) Out 3 (Green) 4 (Green) 3 (Green) 4 Request to Send (RTS) In 5 Clear to Send (CTS) Out 6 Data Set Ready (DSR) Out 4 (Red) 3 (Red) 4 (Red) 7 Ground 5 (Black) 2 (Black) 5 (Black) COM 8 Data Carrier Detect (DCD) Out 9 3.3VDC Output Out VDC Input In 14 RS-485 TX+/RX+ Out RX+ 15 RS-485 TX-/RX- Out RX- 20 Data Terminal Ready (DTR) In 21 RS-485 RX+ In TX+ 22 RS-485 RX- In TX- Notes: 1. DTR handling on the UDS-1100 is set to Ignore by default. 2. For RS-232 operation jumper pins 4 & 5 together. 3. For 2-wire RS-485 operation wire pins 14 (TX+) and 21 (RX+) together and pins 15 (TX-) and 22 (RX-) together. Power must also be supplied to the UDS-1100 using the supplied AC adaptor or via the connections on the DB-25 connector. The UDS-1100 may require up to 125mA from the unregulated power input, with a nominal 12VDC supply typical quiescent current drain is 60mA, typical operating current is 85mA. Note: There is an optional terminal block adaptor available for use with the UDS-1100 that provides screw terminal connections when using RS-485. This is Lantronix part number R. It provides separate terminal blocks for full/half-duplex RS-485 and the power input. Contact Canary Systems to order this adaptor. Using the Lantronix UDS-1100 Device Server Page 1 of 8

2 UDS-1100 Configuration Note: You will need to install the Lantronix DeviceInstaller software to configure the UDS Use the supplied CD. Steps as follows: 1. Connect power to the UDS-1100 using the supplied AC Adaptor. Using an RJ45 cable connect the Ethernet port on the UDS-1100 to the hub or switch being used by your computer. Make sure the green link light on the UDS-1100 is illuminated before proceeding 2. Run the DeviceInstaller software. You should see your network adaptor (Local Area Connection) shown in the navigator on the left. 3. Double-click on the Local Area Connection item to show the UDS connections. Using the Lantronix UDS-1100 Device Server Page 2 of 8

3 4. Double-click on the UDS connections to show the specific adaptors found. Note: If the adaptor does not show then check the power/rj45 connections, otherwise the adaptor may already be configured with an IP. By default the units are configured for DHCP which means they should be assigned an IP when connected to the network your computer is on. See the last section for instructions on configuring units with an unknown or unreachable IP. 5. Click on the tab Web Configuration, then External Browser. This will launch your default browser with the DHCP selected IP. Using the Lantronix UDS-1100 Device Server Page 3 of 8

4 6. The login dialog will display, just press <ENTER> or click the OK button to advance to the configuration screen, shown below. 7. Click on the Network option in the menu on the left to display the Network Settings form. Note the Use the following IP configuration group. Select this option and then configure the appropriate IP Address, Subnet Mask and Default Gateway to match the network to which the UDS-1100 will be connected. Using the Lantronix UDS-1100 Device Server Page 4 of 8

5 8. Click on the Channel 1 Serial Settings item and verify the settings shown below. These are the default settings. Configure the Protocol and Baud Rate according to the table shown below. Device Protocol Baud Rate Leica Total Station RS CR2xx RS CR800/CR1000 RS CR800/CR1000 RS Last step, click on the Apply Settings item shown in the menu on the left. Using the Lantronix UDS-1100 Device Server Page 5 of 8

6 Lost or Unknown IP Configuration This section will provide instructions for configuring the UDS-1100 IP address where the existing address is unknown or in a different subnet so communication from the host device is not possible using the Lantronix DeviceInstaller software. You will need the AC Adaptor and the DB25 to DB9 serial cable that are supplied with the unit. Connect the serial cable to the serial port on your computer. Start Hyperterminal (usually found in the Accessories Communications group), the first dialog will require you to configure a name for the connection. Use the baud rate in the Name for easier launch of Hyperterminal, as shown. Press OK to advance to the Connect To dialog, select the appropriate COM port from the list of available ports. The example uses COM1. Using the Lantronix UDS-1100 Device Server Page 6 of 8

7 Press OK to advance to the COM Properties dialog, Configure Bits per second of 9600, Data bits of 8, Parity = None, Stop bits = 1 and Flow control = None, as shown at right. Click OK to advance to the communications window. The port will be opened and available for communications after clicking OK. While holding the x key down (lower case), connect power to the UDS After a few seconds you should see the configuration screen as shown below. If the configuration screen doesn t show after 15 seconds then disconnect power and repeat the sequence. Using the Lantronix UDS-1100 Device Server Page 7 of 8

8 Press <ENTER> to go into Setup Mode. Note: You only have about 5 seconds to press <ENTER> otherwise the UDS-1100 will time out of configuration mode. After pressing <ENTER> the current settings followed by the Change Setup screen will display. You can use the scroll bar control on the right to back up the display and view the current configuration. Enter 0 <ENTER> for Server configuration. You will then be prompted to enter the 4 octets, one at a time, for the IP Address. This is followed by the Set Gateway IP Address, default is N but press Y to configure and then enter the 4 octets one at a time as needed. Configure Netmask if needed, then Change telnet config password if necessary. The Change Setup menu will re-display, optionally the serial port settings can be configured using option 1 <ENTER>, otherwise select 9 <ENTER> to save the settings and exit. You should be able to run DeviceInstaller now and connect to the UDS Using the Lantronix UDS-1100 Device Server Page 8 of 8