Aggregation of Data. Flowgates, Cutplanes, and Paths can be defined as interfaces

Transcription

1 Aggregation of Data Areas and Zones Interfaces Flowgates, Cutplanes, and Paths can be defined as interfaces Nomograms Super Areas Injection Groups Substations Difference Flows to compare different cases values in the case (loads, gen MW outputs, etc ) Also compare the topology of the case I5-1

2 Area and Zone Records Area and Zone definitions are part of standard power system case text formats Each bus is assigned to exactly one area Each bus is assigned to exactly one zone Generators, Shunts, and Loads are normally assigned to the same area as their terminal bus However, they may also be given their own area and zone designation I5-2

3 Area and Zone Layouts Areas and Zones do NOT have to be contiguous Zones are often sub-areas, but this is NOT required. They can overlap as shown below Areas (thick lines) Zones (shaded/nonshaded) Area 1 Area 2 Zone 1 Zone 2 A single area may consist of multiple zones, while a single zone can include buses from multiple areas I5-3

4 What are Areas and Zones For? Areas and Zones Provide summary data about a group of power system elements (total load, generation, losses, etc ) Provide way to filter data (Area/Zone filters) Limit Monitoring Settings for Area/Zone Toggle settings for equivalencing, scaling, etc Areas ONLY (control settings) Ability to perform automatic generation control (AGC) Ability to specify MW transfer between areas Ability to toggle control settings across a group of elements AGC, Generator AVR, Shunts, Transformers Ability to enable OPF/SCOPF constraint enforcement I5-4

5 Assigning Area and Zone Designations To create a new Area or Zone Make sure you re in Edit Mode (for all methods) Open Model Explorer and choose Network Buses or open the Bus Dialog and assign an existing bus to a new Area/Zone number; OR Select Insert from the local menu (right-click) in Area Records or Zone Records; OR Auxiliary files or Copy/Paste from Excel Enter a new number to create a new Area I5-5

6 Moving Bus Zones and Creating New Zones via the Zone Dialog Buses can be assigned individually to zones using the Bus dialog. Groups of buses can be moved to different zones using the Zone Information dialog. Zone information dialog is available by right-clicking on the zone name on the Zone Records display. I5-6

7 Edit Mode Zone Dialog Zone number List of all buses in the zone To move a group of buses to a new zone, first enter the new zone number here. Then select buses to move. Finally click here to move the buses I5-7

8 Run Mode Zone Dialog Use combo box and/or arrows to view other zones Tells range of AGC generation in zone Zones can have tie-lines, but AGC on zones is not allowed I5-8

9 Interface Definition Interfaces are groupings of branches and sometimes other elements The sum of the flows on these elements can then be monitored in the analysis tools Common interfaces are the grouping of tie lines between areas, and groupings of lines between important parts of the system. Interfaces can be used to model several commonly described groupings of lines Flowgates term used in the Eastern United States Cut-Planes term used in the Western United States Paths term used in the state of California Nomograms Used throughout the industry I5-9

10 Interface Records Interface records can be used to show flows between areas and/or zones. Interface records showing area to area flows can be automatically inserted by Open Model Explorer and choose Aggregations Interfaces to display interface records Select Interface records Auto Insert Interfaces from the local menu to display Auto Insertion of Interfaces Dialog I5-10

11 Interface Records Right-click and select Interface records Auto Insert Interfaces Select either Area to Area, or Zone to Zone flows I5-11

12 Defining Custom Interface Records Open Model Explorer and choose Aggregations Interfaces to view the Interface display. Right-click and select Insert to add a new interface. The Interface Dialog is shown. We ll set up interface showing flow on two parallel lines. I5-12

13 Monitored Interface Dialog Change Interface Name: Top Export Modify Interface Limit A (MW): 400 Click Insert New Element button to add a new element Type: Line/Transformer Near : 2 (Two) Far : 6(Six) CKT 1 Repeat For Type: Line/Transf. Near : 5 (Five) Far : 7 (Seven) I5-13

14 Interface Element Type Line/Transformer Monitor the flows on a line (direction is important!) Area to Area, and Zone to Zone Monitor the sum of the flows on all tie lines Line Open/Close Contingency When defining these, it means that all monitoring on this interface is done after this Line Open/Close contingency DC Line Monitor the flow on a DC Line Injection Group, Generator, Load Monitor the output of a group of generators or loads Allows you to put a limit on the sum of outputs MS Line Monitor the flow on a multi-section line Interface Monitor the flow/output of another interface Be careful not create circular references I5-14

15 Monitored Interface Dialog Interface Name Add a new element to the interface Add or delete interfaces Lists all elements in interface. Right-Click and Choose Show Dialog to modify Use spin button to view other interfaces Set weighting of individual elements I5-15

16 Interface Element Weightings Right-click on the list of elements and choose Display/Column Options Add the columns Weighting and Pre- Weight Flow This allows your interface to monitor the weighted sum of flows instead of the pure sum. This will be used extensively with Nomogram Definitions I5-16

17 Nomograms Nomograms allow definition of 2-dimensional limit spaces using 2 interfaces Nomogram Breakpoints I5-17

18 Nomograms Open Model Explorer and choose Aggregations Nomograms to bring up a list of Nomograms Right-click and choose Insert to bring up the Nomogram Dialog for adding a new Nomogram A nomogram is defined by Interface A Interface B A set of breakpoints Breakpoints MUST create a convex region Nomogram limits can be used in ATC, contingency analysis, and OPF/SCOPF I5-18

19 Nomogram Dialog Interfaces are defined the same as before Define Interface A Define Interface B Specify Breakpoints graphical representation of the breakpoints; operating region may span 4 quadrants I5-19

20 Nomogram Interfaces For each nomogram, Simulator creates a list of nomogram interfaces which are managed internally This is done by using element weightings based on Interface A, Interface B, and the Breakpoints number of breakpoints minus 1 nomogram interfaces are made The monitoring will then occur for each nomogram interface level. Everywhere you see references to interfaces you will now also see references to nomogram interfaces Each line represents a nomogram interface I5-20

21 Nomogram Interfaces Once you have defined a Nomogram, then the Case Information, Nomograms list will have a second tab that lists the Nomogram Interfaces Note: you can not edit Nomogram Interfaces directly. You must modify the Nomogram itself instead Nomogram Interfaces are identified Nomogram Name Nomogram Segment I5-21

22 Area/Zone/Interface Oneline Graphics Oneline diagrams traditionally contain information regarding individual power system elements (buses, lines, generators, etc ) Simulator also allows you to create diagrams based off the aggregate data objects I5-22

23 Area Fields Area fields can be added to onelines to show a number of area fields. Area fields can also be used to specify base transactions. Area fields are inserted in Edit Mode from the Draw ribbon tab, choosing Field Area Field By default area fields are linked to area associated with closest bus on the oneline. I5-23

24 Area Field Dialog Anchor the field to the area object so that both can be moved together; include units suffix Status can be toggled on the oneline Area number 0 (zero) represents the whole system! Use combo box to select an area or entire case Other Area Number field entry required I5-24

25 Area Field Example Add several area fields to the B7FLAT case Area Name Area MW Flow to Other Area (or case) Scheduled Flow to Other Area Load Schedule Multiplier AGC Status I5-25

26 B7FLAT with Area Fields Scheduled MW flows Text fields Left-click to toggle AGC Area fields I5-26

27 Area, Zone, and Super Area Objects Separate oneline object types for Areas, Zones, and Super Areas On B7FLAT case From the Application Menu, select New Oneline to make a new oneline Add area objects for each of three areas From the Application Menu, select Save Oneline to save the oneline. Use b7flata for the name. Zone and Super Area objects are similar I5-27

28 B7FLATA Display Right-click on object, then select Information Dialog for the Area Display Options Same procedure for zones or super areas I5-28

29 Area or Zone Palette Similar to the Bus Palette, you can also bring up an Area or Zone Palette On the Draw ribbon tab, select Show Insert Palette For Zones (or Areas) I5-29

30 Interface Fields Several types of objects are used to display interface data on the oneline Interface Objects: like transmission lines Interface Fields: like line fields Interface Pie Charts: like line flow pie charts I5-30

31 Auto Insertion of Interface Objects Interface objects can be auto inserted (just like line objects). In edit mode, from the Draw ribbon tab, select Auto Insert Interfaces. Allows insertion of interfaces and pie charts. Interfaces are automatically anchored to area/zone objects. I5-31

32 Auto Insertion of Interface Objects Example interface object showing flow from area Top to Area Left Default pie chart size Select OK to auto insert the interface objects I5-32

33 With Interface/Area Fields Text field and area field Interface field Rightclick on object to view area dialog Pie charts require that limits be defined Animated flows can be shown I5-33

34 Super Areas Super areas are groupings of individual areas; analogous to an area being a grouping of individual buses Super areas can be used to control several areas together Open Model Explorer and choose Aggregations Super Areas to see the Super Area Records Right-click and select Insert Super Area Dialog is displayed with default name assigned to the new super area I5-34

35 Super Area Dialog Areas already included Control for Super Area; this control overrides all individual area control settings unless on No Super Area Control Add by name or add by numbers I5-35

36 Super Area Dialog Area Interchange Information Super area summary information I5-36

37 Super Area ED Control for B7Flat Case I5-37

38 Injection Groups Represents grouping of injections of power Loads Generators Switched Shunts Other Injection Groups (be careful of circular references) Useful for defining more specific groups of sources and sinks in many tools Especially useful for ATC, PVQV tools. Also for Sensitivities (PTDF, TLR, etc ) Also useful for generally reporting. Can make an aggregation of generators and show the sum of their output I5-38

39 Injection Groups Open Model Explorer and choose Aggregations Injection Groups Right-click, select Insert Injection Groups Dialog is displayed with default name assigned to the new injection group Right-click in the Participation Points grid and Insert elements into the injection group or click Insert Points Auto Insertion also available from the local menu in Model Explorer I5-39

40 Injection Groups Add loads, generators, shunts, or other injection groups Elements available for adding Choose how to determine the participation factor for each element Elements already in the injection group I5-40

41 Injection Group Participation Points Injection Groups are made up of Participation Points which have two main attributes Reference to a generator, load, switched shunt, or another injection group Participation factor Note: this participation factor is independent of the generator object s participation factor When you create a participation point, you can define the initial participation factor for the point using various methods. This is depicted on the following slide I5-41

42 Injection Group Participation Points: Participation Factors For a generator the choices for participation factor are shown to the right Specify particular value Use generator s participation factor Base on positive reserve (Max Present MW) All units will hit their maximum at same time Base on negative reserve (Present Min) All units will hit their minimum at same time Base on MW capability (Max MW) Use Custom Floating Point Field Recalculate Factor Dynamically Normally the participation factor will only be calculated at this time. Check this box to automatically recalculate the factors EVERY TIME they are used This way if you use the injection group with a different case or different system state it will still be what you intend. I5-42

43 Injection Group Display Objects You can also insert display objects which represent Injection Groups On the Draw ribbon tab, choose Aggregation Injection Group Click on the oneline where you would like to place the injection group Display objects show the generation and load which exist inside the group Generators MW MW I5-43

44 0 M W 0 MVR 0 M W 0 MW 0 M W 0 M VR 0 MVR 0 MVR 0 M W 0 M VR 92% 98% 0 M W 0 MVR 107 MW 5 M VR 107 MW 107 MW107 MW 98% 5 M VR 98% 5 M VR 5 M VR 90% 90% 0 M W 0 M VR 107 MW 10 MVR 107 MW 1 0 M VR 0 M W 0 M VR 670 MW 46 MVR 0 M W 0 M VR 95% 95% 94% 670 MW 46 MVR 777 MW 58 MVR 93% 770 MW 5 7 M VR 110 MW 4 MVR 110 MW 110 MW110 MW110 MW 4 M VR 4 M VR 4 MVR 4 MVR Substations Some substations in a power system have a large number of buses in them Large power stations Other important places in a power system Traditional Power System Cases do not have any reference to which substation a bus is inside. Simulator allows you to define this relationship and then create substation-based diagrams COULEE21 COULEE20 COULEE24 COULEE19 COULEE22 COULEE23 COULEE&1 COULEE&A COULEE COULEES3 COULE EJ COULEE&2 COULEE&4 COULE 69 COULEE&3 COULE AD COULEES2 COULEE COULEE&B COULEE&C COULEE COULEE&2 COULEE&1 COULE 15 COULEES1 27 Grand Coulee Buses are placed in a single substation Grand Coulee 500 Kv Switchyard kV COUL2GPD I5-44

45 Creating Substations To create a new Substation Make sure you re in Edit Mode (for all methods) Open Network Buses in the Model Explorer or open the Bus Dialog and assign an existing bus to a new Substation number; OR Select Insert from the local menu (right-click) in Substation Records; OR Auxiliary files or Copy/Paste from Excel Enter a new number to create a new Substation I5-45

46 Substation Display Objects You can also insert display objects which represent Substations From the Draw ribbon tab, choose Aggregation Substation Click on the oneline where you would like to place the injection group Note: You can also auto-insert transmission lines between Substation objects Name of Substation Substation Number of buses which are assigned 2 138kV 2008 to the PowerWorld substation Corporation Symbols indicates whether Generation, Load, or Shunts exist inside the substation I5-46

47 Difference Flows Simulator allows two different power system cases to be simultaneously loaded Present Case Base Case Difference flows allow viewing of either case or differences between the cases I5-47

48 Difference Flows Dialog Difference Flows Dialog is used to control which case is being viewed. Difference Flows Dialog can be viewed by either Difference Flows option on oneline local menu Difference Flows on the Tools ribbon tab while in Run Mode I5-48

49 Difference Flows Dialog Once base case has been set its values can not be changed Select to set present case as the base case Select to change which case is being viewed Clears the base case from memory The difference flows options affect the onelines AND the case information displays I5-49

50 Load Increased by 20% Load increased by 20 percent Click to change view Current case I5-50

51 Difference Flows Difference flows You can NOT change values in the difference mode! Case Information Displays are also showing differences Notice that all fields are now showing the difference between the present case and the base case. I5-51

52 Comparing Two Different Case Files Simulator only allows one case to be open at a time. When you open a case, all information about the previously opened case is removed, with one exception The Difference flows information is kept Thus to compare two cases, you Open case #1, and go to Run Mode Open Difference Flows and choose Set Present as Base Case Open case #2 Open Difference Flows and change to Difference Case I5-52

53 Topological Comparison of Cases On the Tools ribbon tab, choose Difference Flows Present Topological Differences from Base Case Go to tabs for detailed lists Columns show the number of new, removed elements New: elements in the present case which are not in the base case Removed: elements not in the present case which were in the base case Both: element in the present case and the base case I5-53

54 Topological Differences: Elements Removed Tab Tab provides a list of removed elements Also provides a reason why they were not found in the present case. I5-54