sliding door hardware Slide-A-Track

Size: px
Start display at page:

Download "sliding door hardware Slide-A-Track"

Transcription

1 sliding door hardware Slide-A-Track Straight Light Double Track Systems Straight Medium Double Track Systems Straight Heavy Double Track Systems General Information Straight Light Single Track Systems Straight Medium Single Track Systems Straight Heavy Single Track Systems General Information

2 straight light double track general arrangements architectural details S WEIGHING UP TO 180kg No. A-3 Track is supplied in lengths of 1800mm, 400mm, 3000mm and 6000mm, and lengths may be cut or joined as required. Each length is pierced for fixing at each end and at approximately 600mm intervals along the length of the track. For Face of Wall (FW) installation, 1 x No. A-119 Bracket with x 1/4 BSW x 0mm screws are required for each fixing point. For under Lintel (UL) installation, the track is fixed to the lintel at each fixing point and no Brackets are required. At each track join 1 x No. A-77 Joining Sleeve should be used and in each end of the track 1 x No. 74 Stop (rubber) should be fitted. For each door x No. A-30 or A30L Carriages are required. Timber Doors Up to 60mm thick. Light timber doors will require x No. 110 Door Plates to fix the Carriages to the door and 1 x No. 50 Floor Guide for each grooved door where the door s traverse does not exceed its width. For heavy timber doors the use of No. 141 Aprons with No. 15 Adjusting Nuts instead of No. 110 Door Plates is recommended. S REQUIRED FACE of WALL INSTALLATIon Double A-3 Track for opening width plus full length of traverse of doors. 1 x No. A-119 Bracket with x 1/4 BSW x 0mm mushroom head MT screws for each fixing point. 1 x No. A-77 Joining Sleeve for each track join. 1 x No. 74 Stop (rubber) at each end of the No. A-3 Tracks. 1 x No. A-74 Door Stop for each door (optional). x No. A-30 Carriages for each door. UNDEr Lintel INSTALLATIon Track and fittings as for Face of Wall Fixing but without No. A-119 Bracket and MT screws and usually without No. A-74 Door Stops. PLUS (for timber doors only) x No. 110 Door Plates OR x No. 141 Aprons with x No. 15 Adjusting Nuts. 1 x No. 50 Floor Guide for grooved timber door where the door s traverse does not exceed the width of the door. Double, equal in length to the double No. A-3 Track. x No. A-61 Floor Guides. components June 016 SECTION 1/1

3 straight medium double track general arrangements architectural details S WEIGHING UP TO 70kg No. 1 Track is supplied in lengths of 1800mm, 100mm, 400mm, 3000mm, and 6000mm and lengths may be cut or joined as required. Brackets should be fitted at intervals of not more than 750mm along the length of each track, at each track join and with end plates at both ends of the track. For each door, x No. A35 or A35L Carriages are required. Timber Doors Up to 60mm thick. For attaching Carriages each door will require x A4 Door Plates or x No. 40 Aprons with x No. 5 Adjusting Nuts and 8 x No. 1 x 40mm RH woodscrews. S REQUIRED FACE of WALL INSTALLATIon Double No. 1 Track for opening width plus full length of traverse of doors. 1 x No. A-19 Bracket with x No. A-1 Brackets each fixed by Countersunk 1/ BSW x 40mm screws with nuts are required at each end of the tracks, at each track join and at intervals of not more than 750mm along the length of the tracks. 1 x No. A-11 End Plate should be fitted to each No. A-1 Bracket at the ends of the tracks. 1 x No. A-74 Door Stop for each door (optional). x No. A-35 Carriages are required for each door. PLUS (for timber doors only) x No. 40 Aprons with x No. 5 Adjusting Nuts per door. UNDEr Lintel INSTALLATI on Double No. 1 Track for opening width plus full length of traverse of doors. 1 x No. A-16 Bracket must be fitted at each end of the tracks, at each track join and at intervals of not more than 750mm along the length of the tracks. 1 x No. A-74 Door Stop for each door (optional). x No. A-35 Carriages are required for each door. PLUS (for timber doors only) x No. 40 Aprons with x No. 5 Adjusting Nuts per door. Double, equal in length to the double No. 1 Track. x No. A-61 Floor Guides. components June 016 SECTION 1/

4 straight heavy double track general arrangements architectural details S WEIGHING UP TO 500kg No. 1 Track is supplied in lengths of 1800mm, 100mm, 400mm, 3000mm, and 6000mm and lengths may be cut or joined as required. Brackets should be fitted at intervals of not more than 600mm along the length of each track, at each track join and with end plates at both ends of each track. For each door, x No. A36 or A36L Carriages are required. NOTE: For installations in locations higher than normal atmospheric temperatures, steel wheeled No. A45 or A45L Carriages should be used. Timber Doors Up to 70mm thick. For attaching the Carriages to the door, each door will require x No. 41 Aprons with x No. 5 Adjusting Nuts and 16 x No. 1 x 40mm RH woodscrews. S REQUIRED FACE of WALL INSTALLATIon Double No. 1 Track for opening width plus full length of traverse of doors. 1 x No. A-19 Bracket with x No. A-1 Brackets, each fixed by Countersunk 1/ BSW x 40mm screws with nuts are required at each end of the tracks, at each track join and at intervals of not more than 600mmm along the length of the tracks. 1 x No. A-11 End Plate should be fitted to each No. A-1 Bracket at the ends of the tracks. 1 x No. A-74 Door Stop for each door (optional). x No. A-36 Carriages are required for each door. PLUS (for timber doors only) x No. 41 Aprons with x No. 5 Adjusting Nuts per door. UNDEr Lintel INSTALLATIon Double No. 1 Track for opening width plus full length of traverse of doors. 1 x No. A-16 Bracket must be fitted at each end of the tracks, at each track join and at intervals of not more than 600mm along the length of the tracks. 1 x No. A-74 Door Stop for each door (optional). x No. A-36 Carriages are required for each door. PLUS (for timber doors only) x No. 41 Aprons with x No. 5 Adjusting Nuts per door. Double, equal in length to the double No. A-3 Track. x No. A-61 Floor Guides. components June 016 SECTION 1/3

5 straight light double track systems ready reference of parts required for more common installations Face of wall installation for doors up to 180kg Installation Type No. A (doors clearing full opening width). No. A-3 Track Under lintel installation for doors up to 180kg Installation Type No. F (doors clearing half opening width). TRACK AND TRACK FOR OPENING WIDTHS (mm) A mm A mm A mm No. A-119 Brackets with x 1 / 4 BSW x 0mm Mushroom Head Screws & Nuts No. 77 Joining Sleeve No. 74 Stops (rubber) Product Code No. A-30 Carriages No. A-74 Door Stop (optional) 1 8A mm 8A mm A mm No. A-61 Floor Guides for use with. Alternate for Commercial or Residential Installations. No. A-1 Aluminium Floor Track with No. A-161 Nylon Guides or may be used instead of the heavier No. 8 steel Floor Track and No. A-61 Floor Guides. No. 50 Floor Guides may be used as for grooved doors (instead of shown above) when the door traverse does not exceed its width. No. 110 Door Plates OR No. 141 Aprons with No. 15 Adjusting Nuts. No. A-3 Track TRACK AND TRACK FOR OPENING WIDTHS (mm) A mm 4 4 A mm 4 4 A mm 4 4 No. 77 Joining Sleeve No. 74 Stops (rubber) No. A-30 Carriages No. A-74 Door Stop (optional) 1 8A mm 4 4 8A mm 4 4 8A mm 4 4 No. A-61 Floor Guides for use with. Alternate for Commercial or Residential Installations. No. A-1 Aluminium Floor Track with No. A-161 Nylon Guides or may be used instead of the heavier No. 8 steel Floor Track and No. A-61 Floor Guides. No. 50 Floor Guides may be used as for grooved doors (instead of shown above). No. 110 Door Plates OR No. 141 Aprons with No. 15 Adjusting Nuts. PER 1 PER 1 (To ensure supply of correct components, please specify and order by Part Number.) June 016 SECTION 1/4

6 straight medium double track systems ready reference of parts required for more common installations Face of wall installation for doors up to 70kg Installation Type No. A (doors clearing full opening width). No. 1 Track TRACK AND TRACK FOR OPENING WIDTHS (mm) mm mm mm No. A-1 Brackets with 1 / BSW x 40mm Csk. Screws & Nuts No. A-11 End Plates No. A-19 Brackets Product Code No. A-35 Carriages No. A-74 Door Stop (optional) 1 8A mm 6 8A mm A mm No. A-61 Floor Guides for use with. A4 or No. 40 Aprons No. 5 Adjusting Nuts PER Under lintel installation for doors up to 70kg Installation Type No. F (doors clearing half opening width). No. 1 Track TRACK AND TRACK FOR OPENING WIDTHS (mm) mm mm mm mm 4 4 No. A-16 Brackets No. A-35 Carriages No. A-74 Door Stop (optional) 1 8A mm 4 4 8A mm 4 8A mm 4 8A mm 4 4 No. A-61 Floor Guides for use with. A4 or No. 40 Aprons No. 5 Adjusting Nuts PER (To ensure supply of correct components, please specify and order by Part Number.) June 016 SECTION 1/5

7 straight heavy double track systems ready reference of parts required for more common installations Face of wall installation for doors up to 500kg Installation Type No. A (doors clearing full opening width). No. 1 Track TRACK AND TRACK FOR OPENING WIDTHS (mm) mm mm mm No. A-1 Brackets with 1 / BSW x 40mm Csk. Screws & Nuts No. A-19 Brackets No. A-11 End Plates Product Code No. A-36 Carriages No. A-74 Door Stop (optional) 1 8A mm 6 8A mm A mm No. A-61 Floor Guides for use with. No. 41 Aprons No. 5 Adjusting Nuts PER Under lintel installation for doors up to 500kg Installation Type No. F (doors clearing half opening width). No. 1 Track TRACK AND TRACK FOR OPENING WIDTHS (mm) mm mm mm mm 4 4 No. A-16 Brackets No. A-36 Carriages No. A-74 Door Stop (optional) 1 8A mm 4 4 8A mm 4 8A mm 4 8A mm 4 4 No. A-61 Floor Guides for use with. No. 41 Aprons No. 5 Adjusting Nuts PER (To ensure supply of correct components, please specify and order by Part Number.) June 016 SECTION 1/6

8 general information some types of straight double track systems SIDE clearances The extent of side clearances on one or both sides of the opening will indicate need for single or double doors. sizes B&D Slide-A-Track equipment has been designed for most sizes, weights and thicknesses of doors. However, for larger openings, two or more doors should be used. This will reduce the weight and size of the doors and provide easier operation. For optimum balance and best performance under adverse conditions, it is recommended that the width of doors should be from one third to two thirds of the height. Doors should lap jambs and parallel doors by 50mm to 75mm and the lintel by 5mm to 50mm. WICkET doors Either sliding or hinged can be installed in most applications. EXTERNAl wall face installation Internal installations are preferable but if internal wall surfaces are required for fixtures, machinery, etc., external wall face installations with weather hoods are satisfactory. floor controls INSTAllATION in corrosive locations Where sliding door systems are installed in locations of high corrosion, such as coastal regions, adequate protective treatment and maintenance, as recommended by paint or surface protection manufacturers, should be carried out. TRACk installation For efficient operation, it is essential that the track be installed straight and true. Any distortion of track alignment, caused by fixing to irregular wall or lintel surfaces, must be eliminated by the use of suitable packing. For usual installations, the track should be level. For special installations, such as gravity operated self-closing doors or gravity conveyors, track may be installed at a suitable constant gradient. LengTH of track For most installations, the length of track required is equal to twice the width of the opening. CARRIAge installation Two carriages are required for each door and in all installations the carriage pendant bolt must be fixed to the door directly above its centre of gravity to ensure vertical hanging. Aprons and/or adjusting nuts are unsuitable for use with metal doors. FlOOR controls Floor controls are essential for all installations. They vary to suit the installation and should be ordered according to the requirements of each installation. (with Anchor and No. A-61 Floor Guides are used for most installations. Timber Floors the Anchor Strips may not be required and the may be screwed into a recess in the floor. stops No. A-74 Doors Stops should be fixed to the wall of the building and positioned level with the centre of gravity of the door usually at half door height. No. 74 Rubber Stops and No. A-11 End Plates are designed to retain the carriages in the track during installation and should not be used as door stops. WEATHER hoods For external wall face installations, weather hoods should be fabricated and fixed to the building wall above the track systems and extend 5mm to 50mm below the top of the door. Fixing Sizes and types of bolts, coach screws, etc., vary to suit the installation, therefore they are not supplied with these systems. June 016 SECTION 1/7

9 straight light single track general arrangements architectural details S WEIGHING UP TO 180kg No. A-3 track is supplied in lengths at 1800mm, 400mm, 3000mm and 6000mm and lengths may be cut or joined as required. Each length is pierced for fixing at each end and at approximately 600mm intervals along the length of the track. For Face of Wall (FW) installation, 1 x No. A-75 Bracket with 1 x 1/4, BSW x 13mm screw is required for each fixing point. For under Lintel (UL) Installation, the track is fixed to the lintel at each fixing point and no Brackets are required. At each track join 1 x No. A-77 Joining Sleeve should be used and in each end of the track 1 x No. 74 Stop (rubber) should be fitted. For each door x No. A-30 or A30L Carriages are required. Timber Doors Up to 60mm thick. Light timber doors will require x No. 110 Door Plates to fix the Carriages to the door, For heavy timber doors the use of No. 141 Aprons with No. 15 Adjusting Nuts instead of No. 110 Door Plates is recommended. Where No. 50 Floor Guides are used door must be grooved. S REQUIRED No. A-3 Track length equal to twice opening width. 1 x No. A 75 Bracket with 1 x 1/4 BSW x 13mm Screw for each fixing point. For Under Lintel installation brackets are not required. 1 x No. 74 Stop (rubber) at each end of the No. A-3 Track. 1 x No. A-77 Joining Sleeve for each track join. 1 x No. A-74 Door Stop for each door. x No. A-30 Carriages are required for each door. PLUS (for timber doors only) x No. 110 Door Plates OR x No. 141 Aprons with x No. 15 Adjusting Nuts. 1 x No. 50 Floor Guide for each grooved door. length equal to twice opening width and x No. A-61 Guide Rollers. or alternatively... 3 x No. 5 OR 3 x No. 56 Guide Rollers may be used for each door which should have 5mm x 3mm steel wearing strips fitted to the full width of the door. COmponents June 016 SECTION 1/8

10 straight medium single track general arrangements architectural details S WEIGHING UP TO 70kg No. 1 Track is supplied in lengths of 1800mm, 100mm, 400mm, 3000mm and 6000mm and lengths may be cut or joined as required. Brackets should be fitted at intervals of not more than 750mm along the length of the track, at each track join and with end plates at both ends of the track. For each door, x No. A35 or A35L Carriages are required. Timber Doors - up to 60mm thick For attaching Carriages each door will require x A4 Door Plates or x No. 40 Aprons with x No. 5 Adjusting Nuts and 8 x No. 1 x 40mm RH woodscrews. S REQUIRED No. 1 Track - length equal to twice opening width. No. A-10 Brackets should be fitted at each end of the track, at each track join and at intervals of not more than 750mm along the length of the track. For Under Lintel installation, No. A-16 Brackets are used instead of the No. A-10 Brackets. No. A-11 End Plates should be fitted to the No. A-10 Brackets at each end of the track. 1 x No. A-74 Door Stop for each door. x No. A-35 Carriages are required for each door. PLUS (for timber doors only) x No. 40 Aprons with x No. 5 Adjusting Nuts per door. length equal to twice opening width and x No. A-61 Guide Rollers. or alternatively... 3 x No. 5 OR 3 x No. 56 Guide Rollers may be used for each door which should have 5mm x 3mm steel wearing strips fitted to the full width of the door. COmponents June 016 SECTION 1/9

11 straight heavy single track general arrangements architectural details S WEIGHING UP TO 500kg No. 1 Track is supplied in lengths of 1800mm, 100mm, 400mm, 3000mm and 6000mm and lengths may be cut or joined as required. Brackets should be fitted at intervals of not more than 600mm along the length of the track, at each track join and with end plates at both ends of the track. For each door, x No. A36 or A36L Carriages are required. NOTE: For installations in locations higher than normal atmospheric temperatures, steel wheeled No. A-45 or A45L carriages should be used. Timber Doors - up to 70mm thick For attaching the Carriages to the door, each door will require x No. 41 Aprons with x No. 5 Adjusting Nuts and 16 x No. 1 x 40 RH woodscrews. S REQUIRED No. 1 Track - length equal to twice opening width. No. A-10 Brackets should be fitted at each end of the track, at each join and at intervals of not more than 600mm along the length of the track. For Under Lintel installation, No. A-16 Brackets are used instead of the No. A-10 Brackets. No. A-11 End Plates should be fitted in to the No. A-l0 Brackets at each end of the track. x No. A-36 Carriages are required for each door. PLUS (for timber doors only) x No. 41 Aprons with x No. 5 Adjusting Nuts. 1 x No. A-74 Door Stop for each door. equal in length to the No. 1 Track and x No. A-61 Guide Rollers or alternatively... 3 x No. 5 or 3 x No. 56 Guide Rollers may be used for each door which should have 5mm x 3mm steel wearing strips fitted to the full width of the door. COmponents June 016 SECTION 1/10

12 straight single track systems ready reference of parts required for more common installations Straight Light Single Track System for Doors up to 180kg No. A-3 Track TRACK AND TRACK FOR OPENING WIDTHS (mm) A mm 1 1 A mm A mm 1 1 No. A-75 Brackets No. A-77 Joining Sleeves No. 74 Stops (rubber) Product Code No. A-36 Carriages No. A-74 Door Stops 8A mm 1 1 8A mm A mm 1 1 No. A-61 Floor Guides (with ). OR alternatively... No. 5 or No. 56 Guide Rollers with 5mm x 3mm Wearing Strips (without the ). For Bi-Parting Doors, 4 x No. 54 Door Guides are required for each opening No. 50 floor Guides may be used with grooved doors instead of the and. No. 110 Door Plates OR No. 141 Aprons with No. 15 Adjusting Nuts. PER 3 1 Straight Medium Single Track System for Doors up to 70kg No. 1 Track TRACK AND TRACK FOR OPENING WIDTHS (mm) mm mm mm mm 1 1 No. A-10 Brackets No. A-11 End Plates No. A-35 Carriages No. A-74 Door Stops 8A mm 1 8A mm 8A mm 1 1 8A mm 1 1 No. A-61 Floor Guides (with ). OR alternatively... No. 5 or No. 56 Guide Rollers with 5mm x 3mm Wearing Strips (without the ) For Bi-Parting Doors, 4 x No. 54 Door Guides are required for each opening. PER A4 or No. 40 Aprons with No. 5 Adjusting Nuts. 3 (To ensure supply of correct components, please specify and order by Part Number.) June 016 SECTION 1/11

13 straight single track systems ready reference of parts required for more common installations Straight Heavy Single Track System for Doors up to 500kg No. 1 Track TRACK AND TRACK FOR OPENING WIDTHS (mm) mm mm mm mm No. A-10 Brackets No. A-11 End Plates Product Code No. A-36 Carriages No. A-74 Door Stop No. 8 Floor Track (with Anchor 8A mm 1 1 8A mm 8A mm A mm No. A-61 Floor Guides (with ). OR alternatively... No. 5 or No. 56 Guide Rollers with 5mm x 3mm Wearing Strips (without the ) For Bi-Parting Doors, 4 x No. 54 Door Guides are required for each opening. PER No, 41 Aprons with No. 5 Adjusting Nuts 3 (To ensure supply of correct components, please specify and order by Part Number.) June 016 SECTION 1/1

14 general information some types of straight single track systems floor controls architectural details SIDE clearances The extent of side clearances on one or both sides of the opening will need for single or double doors. sizes B&D Slide-A-Track equipment has been designed for most sizes, weights and thicknesses of doors. However, for larger openings, two or more doors should be used. This will reduce the weight and size of the doors and provide easier operation. For optimum balance and best performance under adverse conditions, it is recommended that the width of doors should be from one third to two thirds the height. Doors should over lap jambs by 50mm to 75mm and the lintel by 5mm to 50mm. WICkET doors Either sliding or hinged can be installed in most applications. EXTERNAl wall face installation Internal installations are preferable but if internal wall surfaces are required for fixtures, machinery. etc., external wall face installations with weather hoods are satisfactory. INSTAllATION in corrosive locations Where sliding door systems are installed in locations of high corrosion, such as coastal regions, adequate protective treatment and maintenance, as recommended by paint or surface protection manufacturers, should be carried out. TRACk installation For efficient operation, it is essential that the track be installed straight and true. Any distortion of track alignment, caused by fixing to irregular wall or lintel surfaces, must be eliminated by the use of suitable packing. For usual installations, the track should be level. For special installations, such as gravity operated self-closing doors or gravity conveyors, track may be installed at a suitable constant gradient. LengTH of track For most installations, the length of track required is equal to twice the width of the opening. CARRIAge installation Two carriages are required for each door and in all installations, the carriage pendant bolt must be fixed to the door directly above its centre of gravity to ensure vertical hanging. Aprons and/or adjusting nuts unsuitable for use with metal doors. FlOOR controls Floor controls are essential for all installations. They vary to suit the installation and should be ordered according to the requirements of each installation. (with Anchor and No. A-61 Floor Guides are used for most installations. Timber Floors the Anchor Strips may not be required and the may be screwed into the recess in the floor. External Ground Floor Openings when subjected to heavy traffic where floor track may be filled with gravel, or damaged. it is recommended that either No. 5 or No. 56 Guide Rollers or No. 54 Door Guides be Installed. Bi-Parting Doors No. 54 Door Guides are required at the centre of each opening. stops No. A-74 Door Stops should be fixed to the wall of the building and positioned level with the centre of gravity of the door usually at half door height. No. 74 Rubber Stops and No. A-11 End Plates are designed to retain the carriages in the track during installation and should not be used as door stops. WEATHER Hoods For external wall face installations, weather hoods should be fabricated and fixed to the building wall above the track system and extend 5 mm to 50mm below the top of the door. Fixing Sizes and types of bolts, coach screws, etc. vary to suit the installation, therefore they are not supplied with these systems. June 016 SECTION 1/13

15 notes Product Code June 016 SECTION 1/14

CI/SfB. (31.59) X NOVEMBER 2003 Coburn Interior Sliding Systems

CI/SfB. (31.59) X NOVEMBER 2003 Coburn Interior Sliding Systems Uniclass L4181 EPIC D181 CI/SfB (31.59) X NOVEMBER 2003 Coburn Interior Sliding Systems Interior Sliding Door Gears FOR CUPBOARDS, WARDROBES, INTERIOR SLIDING AND FOLDING DOORS A comprehensive range of

More information

C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S

C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S January 2009 Issue 6 Valu Guide Brackets The Ultimate in Adjustability and Cost Savings Valu Guide brackets are part of a family

More information

How To Fit A Portman Door Leaf

How To Fit A Portman Door Leaf Portman Sliding Door Gear Timber/Frames Doors Frameless Glass Doors Top track Portman top tracks are suitable for door leaves of up to 80kg as standard Material is 6063T6 aluminium alloy anodised to 15

More information

WHI 90-Minute Rated Veneered Door Frame Installation Instructions

WHI 90-Minute Rated Veneered Door Frame Installation Instructions No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,

More information

Integral Kit Instructions

Integral Kit Instructions Integral Kit Instructions For Fisher & Paykel Cabinet widths of 525, 635, 680, 790 mm wide For curved door Models Series B, C, D & G Manual 814980 Updated August 2008 IMPORTANT If your refrigerator has

More information

Packaged Terminal Air Conditioner Wall Sleeve Installation

Packaged Terminal Air Conditioner Wall Sleeve Installation Installation & Maintenance Data IM 1196 Group: PTAC Part Number: 910141799 Date: October 2013 Packaged Terminal Air Conditioner Installation x 42" PGAN with Top-Mounted Hydronic Heat Note: Installation

More information

Interior Pocket Door System. A hiding gliding sliding door

Interior Pocket Door System. A hiding gliding sliding door Interior Pocket Door System hiding gliding sliding door Introduction good fit for you & the room too Our range of Whatever the style or budget we ve got a choice of 3 sliding pocket door systems that will

More information

CLEAR-DIVISIONS CENTERFOLD

CLEAR-DIVISIONS CENTERFOLD CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in

More information

Ceiling Mounted Folding Attic Ladders Installation Instructions

Ceiling Mounted Folding Attic Ladders Installation Instructions Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:

More information

Automatic Door Selection Guide

Automatic Door Selection Guide Automatic Door Selection Guide AAADM 1300 Sumner Avenue Cleveland, OH 44115 P: 216-241-7333 F: 216-241-0105 aaadm@aaadm.com Automatic Door Selection Guide General: The members of AAADM manufacture an assortment

More information

CLEAR-DIVISIONS VARIOFOLD

CLEAR-DIVISIONS VARIOFOLD CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the

More information

K. D. FRAME ASSEMBLY FOR CLOSED STEEL STUD WALLS...Ins 10. FRAME INSTALLATION DETAILS FOR CLOSED STEEL STUD WALLS...Ins 11

K. D. FRAME ASSEMBLY FOR CLOSED STEEL STUD WALLS...Ins 10. FRAME INSTALLATION DETAILS FOR CLOSED STEEL STUD WALLS...Ins 11 K. D. FRAME ASSEMBLY FOR MASONRY WALLS...........................Ins 2 FRAME INSTALLATION DETAILS FOR MASONRY WALLS......................Ins 3 INSTALLING EXISTING MASONRY WALL ANCHORS IN FRAME..................Ins

More information

Installation Window Building In Details

Installation Window Building In Details Installation Window Building In Details INSTALLATION Photo courtesy of Rowe Aluminium DATE: NOVEMBER 2009 REPLACES: AUGUST 2003 INSTALLATION Installation Replaces: Scale: NOT TO SCALE Vantage snap-on couplers

More information

K17.12 Door closers K17. Doors 01.09.2013

K17.12 Door closers K17. Doors 01.09.2013 K17 Doors K17.12 01.09.2013 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com Contents 1. OPTIC door closer TS40(V) with scissor

More information

Sliding and Folding Door Fittings Sliding Door Accessories

Sliding and Folding Door Fittings Sliding Door Accessories Sliding door lock Toplock For 1- and 2-leaf sliding doors Suitable for toughened safty glass and laminated sheet glass Suitable for DIN left and DIN right Max. weight per door leaf 120 kg For glass thickness:

More information

DE Frame with C Series Sidelight

DE Frame with C Series Sidelight TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder

More information

Hürriyet Mah. Dr. Cemil Bengü Cad. No.27/A 34403 Çağlayan / Istanbul

Hürriyet Mah. Dr. Cemil Bengü Cad. No.27/A 34403 Çağlayan / Istanbul Hürriyet Mah. Dr. Cemil Bengü Cad. No.27/A 34403 Çağlayan / Istanbul Tel: +9 0212 224 2392 +9 0212 225 2182 Faks:+9 0212 225 0274 Website: www.alaks.com.tr E-Mail: info@alaks.com.tr 1160F Aluminum Corner

More information

HORIZONTAL INSTALLATION

HORIZONTAL INSTALLATION THERMO/SOLAR Žiar s.r.o. MANUAL FOR INSTALLATION PV SUPPORTING FRAMES HORIZONTAL INSTALLATION Technical alternation reserved A1410 1 12/2014 CONTENT ORD.NO. PAGE Mounting information 3 Mounting, flat roof

More information

CONCEALED BEARING HINGES. StANLEy ARCHItECtuRAL HARDwARE

CONCEALED BEARING HINGES. StANLEy ARCHItECtuRAL HARDwARE CONCEALED BEARING HINGES StANLEy ARCHItECtuRAL HARDwARE STANLEY ARCHITECTURAL HARDWARE TABLE OF CONTENTS Page Table of contents...2 Company history...2 5 knuckle concealed bearing design...3 Full mortise

More information

InForm Mobile Units. Selection. Equipment trolley, filing trolley Printer/PC trolley Overhead/demo trolley

InForm Mobile Units. Selection. Equipment trolley, filing trolley Printer/PC trolley Overhead/demo trolley Selection Equipment trolley, filing trolley Printer/PC trolley Overhead/demo trolley Basic mobile unit Basic mobile with vertical profiles Installation options Functional shelf, low Functional shelf, inclinable

More information

BOQ SPECIFICATIONS. The Blind system consist of a coated aluminium tube of 38 mm diameter with provision of fabric clamping.

BOQ SPECIFICATIONS. The Blind system consist of a coated aluminium tube of 38 mm diameter with provision of fabric clamping. BOQ SPECIFICATIONS VERTICAL BLINDS Vertical Blinds made of glass fibre fabrics in width 5 (or 4 ). Minimum overlapping of ¾ in fabric. Top aluminium anodized rail of 1.4 mm thickness. 2 inch wide channel

More information

glass & Glazing Products

glass & Glazing Products glass & Glazing Products WallMaker Create an unlimited variety of bright, beautiful and secure interior environments with the easy-to-install Stylmark WallMaker glass wall system. This versatile system

More information

Lift-off hinge. Rising hinge. Standard hinge. Heavy duty hinge. Parliament hinge. Spring hinge. Double action spring hinge. Concealed mortise hinge...

Lift-off hinge. Rising hinge. Standard hinge. Heavy duty hinge. Parliament hinge. Spring hinge. Double action spring hinge. Concealed mortise hinge... Door Hinges Contents Butt hinges Lift-off hinge Rising hinge Standard hinge Heavy duty hinge Parliament hinge Spring hinge Double action spring hinge Concealed hinges Concealed mortise hinge... Pivot

More information

Information Technology Solutions

Information Technology Solutions Information Technology Solutions Aluminum Sliding Door Assembly Instructions Shield Doors & Windows Bi-fold Door Assembly Instructions For Support Please Call 03 8339 2252 Aluminum Sliding Door Assembly

More information

INDUSTRIAL & COMMERCIAL DOOR HARDWARE

INDUSTRIAL & COMMERCIAL DOOR HARDWARE C R O W N I N D U S T R I A L INDUSTRIAL & COMMERCIAL DOOR HARDWARE "BARN DOOR HARDWARE" SLIDE DOOR HARDWARE SWING DOOR HARDWARE SLIDE-FOLD DOOR HARDWARE 213 MICHELLE COURT SOUTH SAN FRANCISCO, CA 94080

More information

Installation Instructions and Ordering Information

Installation Instructions and Ordering Information The Flush Finish Trimless Door Frame Installation Instructions and Ordering Information CLEAN LINES! The Flush Finish Door Jamb System Manufactured by STUDCO Building Systems Step 1 Verify if you are using

More information

Technical data sheet PVC Bi-fold doors

Technical data sheet PVC Bi-fold doors Standard Specifications White internally beaded, Deceuninck 3000 series profile 28mm Low-e toughened sealed units with argon gas Open in doors with white handles and hinges Tracks are fitted to the top

More information

V80 HEAD DETAIL - SECTION VIEW DRAWING SCALE 1:2. Dwg. No. V10101. 13mm min. 85mm. 72mm 95mm 65mm. 26mm. 10mm 60mm 75mm. 135mm.

V80 HEAD DETAIL - SECTION VIEW DRAWING SCALE 1:2. Dwg. No. V10101. 13mm min. 85mm. 72mm 95mm 65mm. 26mm. 10mm 60mm 75mm. 135mm. 13mm min. 72mm 95mm 65mm 85mm 26mm 10mm 60mm 75mm 135mm 145mm V80 HEAD DETAIL - SECTION VIEW Dwg. No. V10101 Manually operated blind with gearbox showing 90 & 45 degree crank penetrations in section view.

More information

CLEAR-DIVISIONS APERTO

CLEAR-DIVISIONS APERTO CLEAR-DIVISIONS Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS moveable glass wall system. The yellow highlighted areas in the

More information

HALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL

HALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL HALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL Please read these instructions carefully and completely before attempting to install Hale Pet Doors; they will guide you through the steps

More information

Steel Door Frame Installation in Steel Stud Construction

Steel Door Frame Installation in Steel Stud Construction Steel Door Frame Installation in Steel Stud Construction For use with the Steel Door Institute (SDI) video How to Install a Steel Door Frames in Steel Stud Construction This manual gives you step-by-step

More information

BAGGAGE HANDLING SYSTEMS. Trastecnica S.p.A. Handling Baggage Systems Edition 2002 - Rev. 00-1 -

BAGGAGE HANDLING SYSTEMS. Trastecnica S.p.A. Handling Baggage Systems Edition 2002 - Rev. 00-1 - BAGGAGE HANDLING SYSTEMS Trastecnica S.p.A. Handling Baggage Systems Edition 2002 - Rev. 00-1 - TECHNICAL SPECIFICS INDEX Check-in with one conveyor 4 Scales 6 Belt Conveyors 8 Take away 9 Feeder and Belt

More information

1-800-295-5510 uline.com SPECIFICATIONS

1-800-295-5510 uline.com SPECIFICATIONS H-1394, H-1395, H-1396 H-1397, H-3859, H-3860 π GRAVITY CONVEYOR 1-800-295-5510 uline.com SPECIFICATIONS Conveyor Bed Width In (mm) 18, 24, 30 (457, 610, 762) Load Capacity Per Linear Foot (305mm) Lbs

More information

Removable Aluminium posts

Removable Aluminium posts Post Solent Sail Shades Ltd 120 Billington Gardens Hedge End Southampton SO30 2RT Tel/Fax: 01489 788243 www.solentsailshades.co.uk Email: info@solentsailshades.co.uk Removable Aluminium posts Single Pole

More information

ISSUE 2. Installation Guide

ISSUE 2. Installation Guide ISSUE 2 Installation Guide Here at Slide and Fold, we LOVE our Bi-Fold Plus range of folding-sliding doors. We want to ensure that your customers love them too. So we have created a new, detailed installation

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS door frames Engineered product systems INSTALLATION INSTRUCTIONS door frames MINIMALIST DOOR FRAME Fry Reglet Flush Door frames are designed for use with 3 5/8 studs with ½ drywall both sides (4 5/8 throat

More information

Universal systems for frameless doors

Universal systems for frameless doors EN Universal systems for frameless doors Xinnix Door Systems designs, creates and manufactures systems for internal doors. With our construction elements, it is possible to obtain easily an elegant and

More information

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word

More information

POLE MOUNT SYSTEM-3 INSTALLATION

POLE MOUNT SYSTEM-3 INSTALLATION 1 May 2014 POLE MOUNT SYSTEM-3 INSTALLATION The Pole Mount System-3 is an easy to install and flexible system designed to allow ONE SYSTEMS loudspeaker products to be mounted to pole structures. The only

More information

PTFE Slide Bearings 04/10 149

PTFE Slide Bearings 04/10 149 04/10 149 1.0 GENERAL INFORMATION In a wide range of applications, PTFE Slide bearings are superior to conventional expansion plates, rollers and rocker arm type supports. They support petrochemical plant,

More information

MODEL HSR-007 Direct Drive Rolling Steel

MODEL HSR-007 Direct Drive Rolling Steel MODEL HSR-007 Direct Drive Rolling Steel 200 Fairview Road, Unit #2, Barrie, Ontario L4N 8Z8 Tel: 866-792-9968 or 705-792-9968 Fax: 705-735-9564 www.tnrdoors.com email: info@tnrdoors.com Model HSR-007

More information

CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS

CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,

More information

Residential Garage Door Terminology

Residential Garage Door Terminology A Air Infiltration: The leakage or passage of air through a door system Anodize: A hard non-corrosive oxide film on the surface of aluminum Astragal: A compressible or deformable seal provided on the bottom

More information

9300BC SERIES Light Commercial Door Closer

9300BC SERIES Light Commercial Door Closer Light Commercial Door Closer general information The 9300BC is a durable, economically priced door closer designed for commercial exterior and interior doors such as storefront and industrial applications.

More information

rationel WINDOWS WITH VISION

rationel WINDOWS WITH VISION Brick / Blockwork 340mm Cavity Wall Interface Detail Cill BW-001A 5 x 50mm Woodscrews (Staggered) By Installer 20 x 90mm Standard Timber Packer With Upstand Bedded To Frame In Silicone By Installer Aluminium

More information

STRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM

STRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM Chapter 9 STRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM 9.1 BACKGROUND Steel is widely used in the construction of multi-storey buildings. However, steel construction is seldom used and is traditionally

More information

PART 1 GENERAL 1.1 SECTION INCLUDES

PART 1 GENERAL 1.1 SECTION INCLUDES J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including

More information

PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS

PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS SYSTEM COMPONENTS PREASSEMBLED ELEMENTS FOR FIFTING AND SLIDING DOORS s r ood gn i d i l s dna gn i t f i f r o f s t neme l e de l bme s s ae r P PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS These

More information

Timber Decks. Technical Note. March 2007

Timber Decks. Technical Note. March 2007 Timber Decks Technical Note. March 2007 This Technical Note contains general information for residential timber decks and floor frame structures for veranda s, patios etc which are exposed to the weather.

More information

Schlüter -KERDI-BOARD Substrate, structural panel, bonded waterproofing

Schlüter -KERDI-BOARD Substrate, structural panel, bonded waterproofing Substrate, structural panel, bonded waterproofing The universal substrate for tiles Perfect covering No matter whether you work with mosaics or large format tiles, an absolutely level substrate with straight

More information

Slides and Drawers. The right collection

Slides and Drawers. The right collection Slides and Drawers The right collection 1Technical Details Drawer Runners Carrying capacity Kg. Static load Dynamic load Pag. 01 Concealed Runners Excel N Excel N Excel N Excel N650 Excel N Excel PlugIn,

More information

Fire Resistant Systems

Fire Resistant Systems Fire Resistant Systems A R C H I T E C T U R A L A L U M I N I U M G L A Z I N G S Y S T E M S Fire Resistant Systems Introduction Kawneer are pleased to introduce two new comprehensive Fire Resistant

More information

Linea Weatherboard DIRECT FIX CONCRETE SLAB AND SOFFIT FIGURE 1

Linea Weatherboard DIRECT FIX CONCRETE SLAB AND SOFFIT FIGURE 1 Top plate Stud Soffit lining 45mm min nog Fix scotia bead Building underlay/james Hardie rigid air barrier Soffit Detail Building underlay/james Hardie rigid air barrier Bottom plate 25mm wide cant strip.

More information

Can you design a frameless shower enclosure that doesn't leak?

Can you design a frameless shower enclosure that doesn't leak? Can you design a frameless shower enclosure that doesn't leak? With proper design and installation frameless shower enclosures should not have any problems with water leakage, but they are not 100 percent

More information

INSTRUCTIONS: LocknCharge Laptop Carts

INSTRUCTIONS: LocknCharge Laptop Carts INSTRUCTIONS: LocknCharge Laptop Carts www.lockncharge.com Extra Tools required: Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied) (Panel colours for illustration purposes

More information

Technical Information

Technical Information Technical Information This section of the catalogue provides technical information that will help specify, install and maintain Surelock McGill devices and components. The topics are listed below: Blast

More information

Profiles in stock Standard catalogue. Discover the possibilities with aluminium profiles from Sapa

Profiles in stock Standard catalogue. Discover the possibilities with aluminium profiles from Sapa Profiles in stock Standard catalogue Discover the possibilities with aluminium from Sapa You can create your own profile or you can choose from a wide selection of standard. Delivery: 1 2 weeks for standard

More information

GENERAL SHIELDING REQUIREMENTS FOR DIAGNOSTIC X-RAY FACILITIES. Major Medical (Radio/Fluoro/CT/Cardiac/Chiropractic)

GENERAL SHIELDING REQUIREMENTS FOR DIAGNOSTIC X-RAY FACILITIES. Major Medical (Radio/Fluoro/CT/Cardiac/Chiropractic) GENERAL SHIELDING REQUIREMENTS FOR DIAGNOSTIC X-RAY FACILITIES 1. PROTECTIVE SCREENS (a) Major Medical (Radio/Fluoro/CT/Cardiac/Chiropractic) Typically, 15 kg m -2 (1.3 mm) sheet lead or its shielding

More information

Concepts. Products. Service. Lindner Plus Organisation

Concepts. Products. Service. Lindner Plus Organisation Concepts Products Service Lindner Plus Organisation Building new solutions. Lindner undertakes major worldwide projects in all areas of interior finishes, insulation technology, industrial services and

More information

Lunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide

Lunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your

More information

APPENDIX K. Design/Layout Considerations for Ceiling/Overhead Lift Tracks. Ceiling Lift Motor Charging Options

APPENDIX K. Design/Layout Considerations for Ceiling/Overhead Lift Tracks. Ceiling Lift Motor Charging Options ArjoHuntleigh APPENDIX K Design/Layout Considerations for Ceiling/Overhead Lift Tracks At present, not all clinical units or areas require 100 percent ceiling lift coverage (Table I-1), but with expansion

More information

Rollers. from the UK s largest roller manufacturer. Quality Performance Reliability

Rollers. from the UK s largest roller manufacturer. Quality Performance Reliability Rollers from the UK s largest roller manufacturer Quality Performance Reliability 42 Index Gravity Rollers Light to Medium Duty 4 Heavy Duty 5 Plastic Rollers 6 Stainless Steel Rollers 7 Grooved Rollers

More information

STEWART GILL CONVEYORS Ltd

STEWART GILL CONVEYORS Ltd STEWART GILL CONVEYORS Ltd 550M STS SYSTEM overhead - inverted - side mounted - floor mounted - SPECIALISTS IN OVERHEAD CONVEYOR SYSTEMS 2 Index About 550M STS... 3 Track... 4 Track Supports... 5 Bends...

More information

SECTION 6. Glass Storefront Doors:

SECTION 6. Glass Storefront Doors: SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail

More information

Installation Detailed installation instructions are provided which should be strictly followed.

Installation Detailed installation instructions are provided which should be strictly followed. Specification System 6 The Metal Technology Thermally-Broken Vertical Slide Window has been designed in such a way that its'attractive and clean lines will enhance all types of residential and commercial

More information

Guide rail bracket (for adjustable heads)

Guide rail bracket (for adjustable heads) (for adjustable heads) Part. 209 40 ø,5 ø10,5 2 2,5 115 15 42 5 11 37 72 4 70 Code 209 / 0754 MATERIALS: Bracket made out of reinforced polyamide black colour. FEATURES: To be used with heads Part.221,

More information

Series 602 MAGNUM Sliding Window DESIGNER SERIES

Series 602 MAGNUM Sliding Window DESIGNER SERIES Series 602 DESIGNER SERIES DATE: NOVEMBER 2009 REPLACES: AUGUST 2003 DESIGNER SERIES Series 602 KEY EATURES / PERORMANCE CHARACTERISTICS Scale: NOT TO SCALE Designed to complement our existing high quality

More information

19" Data Racks. Adjustable feet To compensate for uneven floors and assure great stability all feet can be up to 20 mm adjusted.

19 Data Racks. Adjustable feet To compensate for uneven floors and assure great stability all feet can be up to 20 mm adjusted. 19" Data Racks Attractive design and high quality are characteristic. Basic framework is welded from multiple bent metal plate, which assures great rigidity suitable for heavier equipment. All profile

More information

Compactus Freetrack 2 Compactus mekdrive 2 Compactus Side2Side 2. Mobile Storage Systems. Design Manual

Compactus Freetrack 2 Compactus mekdrive 2 Compactus Side2Side 2. Mobile Storage Systems. Design Manual Compactus mekdrive 2 Compactus Side2Side 2 Mobile Storage Systems Freetrack 2 This manual remains the sole property of Dexion Commercial (New Zealand) Limited (Precision). The information contained within

More information

WiMo Antennen und Elektronik GmbH Am Gäxwald 14, D-76863 Herxheim Tel. (07276) 96680 FAX 9668-11

WiMo Antennen und Elektronik GmbH Am Gäxwald 14, D-76863 Herxheim Tel. (07276) 96680 FAX 9668-11 The I-PRO Traveller part no. 11440 Thank you for your purchase, please take your time to digest some of the important building tips and the essential matching/adjustment techniques. You will need 8m of

More information

Colonnade Security Pipe

Colonnade Security Pipe Description: Round & Square downpipe formed from extruded 6060 T4 aluminium in various sizes (Ø83mm, Ø108mm, 83x83 mm & 108x108mm*) & supplied with a complete range of accessories i.e. Offsets, bends,

More information

INSTALLATION. General. Important Note. Design. Transport

INSTALLATION. General. Important Note. Design. Transport General The roof trusses you are about to install have been manufactured to precise engineering standards. To ensure that the trusses perform as designed, it is essential that they be handled, erected

More information

Pipe Cutting and Beveling Clamshells

Pipe Cutting and Beveling Clamshells Pipe Cutting and Beveling Clamshells Who We Are One Company, Total Support, Complete Solutions For more than a century, Hydratight has provided world-class bolted joint solutions and continues to set international

More information

Relevant British, European and International standards

Relevant British, European and International standards Relevant British, European and International standards BS 1245:1975 Specification for metal door frames (steel) BS 3621:2007 + A1:2009 Thief resistant lock assemblies - Key egress BS 476-20:1987 Fire tests

More information

AMS 120. EFT Guest Card Terminal & Refund unit

AMS 120. EFT Guest Card Terminal & Refund unit AMS 120 EFT Guest Card Terminal & Refund unit ACCOUNT MANAGEMENT STATIONS Wall mounted kiosk offering Visitor card purchase and refund Card deposit EFT purchase, refund and loading Full statement facilities

More information

mechanics PP-Profiles Panel Profiles PT-Profiles T-Groove Plates RE-Profiles Rectangular Profiles PU-Profiles Universal Profiles

mechanics PP-Profiles Panel Profiles PT-Profiles T-Groove Plates RE-Profiles Rectangular Profiles PU-Profiles Universal Profiles Overview PP-Profiles Panel Profiles PP 50 PP 100 PP 150 PP 200 PP 0 B 4 PT-Profiles T-Groove Plates B 5 PT PT 50 RE-Profiles Rectangular Profiles B 6 RE 15 RE 30 RE40 RE65 PU-Profiles Universal Profiles

More information

Best/Flex Roller Expandable Conveyor

Best/Flex Roller Expandable Conveyor Best Diversified Products Ltd. Best/Flex Roller Expandable Conveyor Product Manual Best Diversified Products Ltd. Brunel Road, Earlstrees Industrial Estate Corby, Northants. NN17 4JW Tel: +44(0) 1536 206969

More information

How To Build A Gambrel Roof And A Gable End Roof

How To Build A Gambrel Roof And A Gable End Roof Dutch Gable or Gambrel Roof and The Scotch Valley The folowing pages are an extract from Carp 12 text TAFE NSW Construction and Transport Division 71 HIP and VALLEY ROOFING GAMBREL / DUTCH GABLE The effect

More information

James M. Pleasants Company

James M. Pleasants Company James M. Pleasants Company SUBMITTAL DATA GAINESVILLE MECHANICAL DECEMBER 20, 2013 PROJECT: GSU: J-183 HUMANITIES LAW BLDG. QUOTE NO:12116 ENGINEER: STEVENS & WILKINSON GASKETED PLATE HEAT EXCHANGER Tag:

More information

Saferand easierinstallation

Saferand easierinstallation EN 85-07 Saferand easierinstallation IföSigninstallationsystem andifösignbuilt-incistern www.ifosanitar.com/sign Aneffectivesolution withmanyadvantages. Ifö Sign installation system makes life a little

More information

For New Technology Network. Steel Manufacturing Machinery Product Guide Book

For New Technology Network. Steel Manufacturing Machinery Product Guide Book For New Technology Network R Steel Manufacturing Machinery Product Guide Book Ecological / Economical proposals from NTN NTN products exhibit benefits at various locations. Steel manufacturing equipment

More information

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2

More information

CDW Systems Ltd Contemporary Doors & Windows

CDW Systems Ltd Contemporary Doors & Windows CDW Systems Ltd Contemporary Doors & Windows The comprehensive product overview A complete specification guide to CDW Systems range of Aluminium windows, doors and curtain walling for commercial and residential

More information

Tel: 0800 975 4933 Sales: sales@avantauk.com STORAGE CABINETS. PREMIERSHIELD anti-bacterial powder coating system. quality products made in the UK

Tel: 0800 975 4933 Sales: sales@avantauk.com STORAGE CABINETS. PREMIERSHIELD anti-bacterial powder coating system. quality products made in the UK Tel: 0800 975 4933 Sales: sales@avantauk.com STORAGE PREMIERSHIELD anti-bacterial powder coating system quality products made in the UK MEDIUM DUTY : 88 SERIES PREMIER BDU DESK UNITS: 88 SERIES Of welded

More information

Vitraflex Classic Modular Combination Shower and Changeroom Cubicles (c/w Telescopic Stainless Steel Leg Anchors)

Vitraflex Classic Modular Combination Shower and Changeroom Cubicles (c/w Telescopic Stainless Steel Leg Anchors) GENERAL PRODUCT SPECIFICATIONS Vitraflex Classic Modular Combination Shower and Changeroom Cubicles (c/w Telescopic Stainless Steel Leg Anchors) (Document Reference CC/GPS/CUBE/03 Rev. 1 April 2010) (E&OE

More information

MGB Chrome Bumper Conversion

MGB Chrome Bumper Conversion MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different

More information

DESIGN CLARIFICATION (DC)

DESIGN CLARIFICATION (DC) DESIGN CLARIFICATION (DC) Owner: Victor Valley Wastewater Reclamation Authority Date: 03/03/2015 Contractor: W M Lyles Carollo Project No.: 8299A.20 Project Name: Subregional WRPs DC No.: 001 DC Title:

More information

ABLOY DC 240 DOOR CLOSER Heavy duty door closer

ABLOY DC 240 DOOR CLOSER Heavy duty door closer ABLOY DC 240 DOOR CLOSER Heavy duty door closer ABLOY DC240 heavy duty door closer offers a wide variety of functional options. ABLOY DC240 DOOR CLOSER The ABLOY DC240 have been developed to meet the exacting

More information

ASX7-4-IOM-7 J30-08579

ASX7-4-IOM-7 J30-08579 INSTALLATION INSTRUCTIONS 4" COMBUSTION AIR INLET KIT TUBULAR GAS FIRED DIRECT SPARK PROPELLER UNIT HEATERS UNIT CONVERSION & CATEGORY III VENTING FOR SEPARATED COMBUSTION For 30,000 to 75,000 BTU/HR SUPPLEMENT

More information

DESIGN BY: ARCH. GIUSEPPE INZITARI

DESIGN BY: ARCH. GIUSEPPE INZITARI DESIGN BY: ARCH. GIUSEPPE INZITARI 218 FOR HIGH THICKNESS FROM 12 TO 17.5 MM - GIUMAX GIUMAX 9500 Page 220 GIUMAX 8500 Page 227 ROLLERS Page 233 GIUMAX 4500 Page 236 GIUMAX 6500 Page 244 FROM 8 TO 12 MM

More information

Bringing good things ahead

Bringing good things ahead Bringing good things ahead Whatever your logistic needs, we can offer a conveyor solution. Our flexible systems primary and secondary packaging for single and multi packages, can transport your goods from

More information

ROLLING CURTAIN DOOR INSTALLATION, MAINTENANCE & PARTS MANUAL WINDLOCK MODEL 955WL

ROLLING CURTAIN DOOR INSTALLATION, MAINTENANCE & PARTS MANUAL WINDLOCK MODEL 955WL ROLLING CURTAIN DOOR INSTALLATION, MAINTENANCE & PARTS MANUAL WINDLOCK MODEL 955WL Read manual thoroughly prior to installing door. Rolling steel doors are large, heavy objects that move with the help

More information

H45 LED - Direct and indirect pendant

H45 LED - Direct and indirect pendant RAL 01 10 00 IP 20 230V 50/60Hz Specifications Direct and indirect light pendant linear luminaire. Aluminium profile. Diffusers in frosted polycarbonate profile. Driver included. Supplied with clear base,

More information

Superform Products Ltd.

Superform Products Ltd. TYPICAL CORNER REINFORCING NOTE : SEE ENGINEERED REBAR SCHEDULES SUPPLIED BY THE MANUFACTURER STEEL REINFORCEMENT WALL CORNER 90 Copyright 2012 Sept. 2012 5.1.1 Rebar Spacing 6" 12" Max. Load LB./FT. 2000

More information

1250 & 1450 SERIES SURFACE MOUNTED CLOSERS

1250 & 1450 SERIES SURFACE MOUNTED CLOSERS 1250 & 1450 SERIES SURFACE MOUNTED OSERS PRODUCT SELECTION GUIDE Surface mounted 1250 & 1450 Series LCN closers feature a modern slim line design for easy installation on narrow head frames and top rails.

More information

Cable Drum Installation

Cable Drum Installation 20 Cable Drum Installation COUNTERBALANCE None Shake the TorqueMaster spring tube gently to extend the winding shafts out about 5" on each side. For single spring applications, there will be no left hand

More information

Fork Lift Truck Attachments

Fork Lift Truck Attachments Lift Truck Attachments Mounted Sweeper - The Basil The fork mounted sweeper is a quick and easy solution for reheaping your loose granule products such as sand, top soil, grain or similar. Optional left

More information

Fredriksons conveyor systems handle goods with a width from 20 mm up to 600 mm.

Fredriksons conveyor systems handle goods with a width from 20 mm up to 600 mm. Conveyor Solutions Whatever your logistic needs, we can offer a conveyor solution. Our flexible systems primary and secondary packaging for single and multi packages, can transport your goods from one

More information

Ref: GA13UK Glass Awning Support System

Ref: GA13UK Glass Awning Support System Ref: GA13UK Glass Awning Support System Give any entrance an uncomplicated, graceful look, enhancing the design of any building. Installation LAMINATED TOUGHENED GLASS High grade 316 stainless steel for

More information

ΑΡΧΙΤΕΚΤΟΝΙΚΑ ΣΥΣΤΗΜΑΤΑ ΑΛΟΥΜΙΝΙΟΥ ARCHITECTURAL ALUMINIUM SYSTEMS

ΑΡΧΙΤΕΚΤΟΝΙΚΑ ΣΥΣΤΗΜΑΤΑ ΑΛΟΥΜΙΝΙΟΥ ARCHITECTURAL ALUMINIUM SYSTEMS ΑΡΧΙΤΕΚΤΟΝΙΚΑ ΣΥΣΤΗΜΑΤΑ ΑΛΟΥΜΙΝΙΟΥ ARCHITECTURAL ALUMINIUM SYSTEMS NORMAL SLIDING and SLIDING WITH THERMAL BREAK A L U M IN IU M S Y S T E M S 32 SERIES 32 SLIDING. : 9045 815 gr/m 475 mm -25-25 - FOR

More information