Hidra H3 RGB - Optic 10 Model No: HID US

Transcription

1 Hidra H3 RGB Optic 10 Certified by C ompliance LM7908 and LM8008 Available for International specifications by adding 'T' at the end of the existing Model # International spec sheets are available upon request Exact Measurements: Metric Model: Installation: Light Color: Color Temperature: Fixture Finish: Fixture Material: Diffuser: HID US Indoor and Outdoor Surface Mounted for Ceilings, walls, floors and posts RGB RGB Black Sable Die cast aluminum Methacrylate Lens Additional Details Surface mounted on wall, ceiling, ground picket, bollard or pole; floodlight family, hybrid optics for an optimal visual comfort, DMX dimmable, Power Supplies and Control gear are not included see components, for wiring diagram see downloads. Optic: 10 Lamp Type: Number of LEDs: Total Wattage: Lamp Voltage: Lamp Life: IP Rating: Power LED RGB 12 24W 24Vdc 50,000 hrs at 70% of lamp lumen output with IES LM80. For optimized perfomance follow instruction sheet. IP65 Width: 57mm / 2 1/4" Length: 110mm / 4 5/16" Height: 160mm / 6 5/16" Breaking Strength: Screws: Gasket: Power Supply: IK05 Stainless Steel AISI 316L Silicone Constant voltage supply 24Vdc dimmable, 30 Tycos Dr. Toronto, ON Canada M6B 1V9 PH: / FAX: tech@zaneen.com Page 1 of 3

2 Hidra H3 RGB Optic 10 parallel connection (Not Included) Control Gear: Sold separately (see components) Lumen Chart Photometric File Power Color Temperature Nominal Lumen Actual Lumen HID.043.XX 24W RGB HID.043.XX R 24W RGB (Red) HID.043.XX G 24W RGB (Green) HID.043.XX B 24W RGB (Blue) Accessories Hidra Bollard with Base [KIT ] 50mm / 2" x 50mm / 2" x 700mm / 27 9/16" Steel Bollard with base Black Hidra Bollard with Rods [KIT ] 60mm / 2 3/8" x 60mm / 2 3/8" x 2,000mm / 78 3/4" Steel Bollard with Rods Black Hidra Bollard with Rods [KIT ] 60mm / 2 3/8" x 60mm / 2 3/8" x 3000mm / 118 1/8" Steel Bollard with Rods Black Hidra Pole Head l [KIT ] 50mm / 2" x 50mm / 2" Pole Head for 1 projector Black Hidra Pole Head 2 [KIT ] 50mm / 2" x 50mm / 2" Pole Head for 2 projector Black Hidra Pole Head 2 [KIT ] 60mm / 2 3/8" x 60mm / 2 3/8" Pole Head for 2 projectors Black Hidra Pole Head 4 [KIT ] 60mm / 2 3/8" x 60mm / 2 3/8" Pole Head for 4 projectors Black Hidra Steel Bollard One Head 40 x 40 x 300 [KIT ] 40mm / 1 9/16" x 40mm / 1 9/16" x 300mm / 11 13/16" 1 Head Steel Bollard Black System Components DMX /010V Control Gear 24Vdc 3 Channels [ECO ] Constant Voltage Dimmable Dali/PWM Interface Control Gear 3 Channels [ECO ] DMX Splitter 1 input / 3 Output channels [ECO ] USB DMX / RDM Interface [ECO ] Power Supply constant voltage 24Vdc 10W [ALI ] Main Voltage Constant 24Vdc V 10W 50/60Hz Power Supply constant voltage 24Vdc 25W [ALI ] Main Voltage Constant 24Vdc V 25W 50/60Hz Power Supply constant voltage 24Vdc 20W [ALI ] Main Voltage Constant 24Vdc V 20W 50/60Hz Available Sizes and / or Lamping Hidra H3 RGB Optic 10 [HID US] 6 Power LED RGB, 24W 24Vdc Black Sable Hidra H3 RGB Optic 22 [HID US] 6 Power LED RGB, 24W 24Vdc Black Sable Hidra H3 RGB Optic 40 [HID US] 6 Power LED RGB, 24W 24Vdc Black Sable Alternative Finish Models Hidra H3 RGB Optic 10 [HID US] 6 Power LED RGB, 24W 24Vdc White Sable Hidra H3 RGB Optic 10 [HID US] 6 Power LED RGB, 24W 24Vdc Gray Sable 30 Tycos Dr. Toronto, ON Canada M6B 1V9 PH: / FAX: tech@zaneen.com Page 2 of 3

3 Hidra H3 RGB Optic Tycos Dr. Toronto, ON Canada M6B 1V9 PH: / FAX: tech@zaneen.com Page 3 of 3

4 R Wiring Diagram Reference Wiring diagrams and electrical connections The new lighting systems, that use light sources in a LED solid state must be connected to the main voltage through electronic devices that maintain the critical parameters of operation constant. With Leds in particular, the current values that pass through the light source must remain constant and if necessary measurements are not taken to keep these parameters constant, the LED will tend to absorb higher currents resulting overheating triggering a vicious mortal cycle of the semiconductor. Because of this physicalelectric phenomenon the systems with LED technology need very sophisticated control devices compared to the traditional sources. The current control can be integrated into the power supply or can be placed between the power supply and the LED system. In this case the Led connection should be done in series with a maximum quantity of 10/12 Led that can be connected In the most evolved systems the control electronic can be split and integrated directly on the PCB together with the Leds; here the connection can be done in parallel with a 24V dc power supply and without any limit of the quantity of Leds that can be connected To facilitate the user in consulting this catalog, in this section there is a list of all the diagrams of connection between control gears, interfaces and power supplies, as well as the combination of the correct power supplies / control gear and lighting systems showing the article codes. Important note: Suggested maximum distance from driver: 30ft (using 18 AWG solid copper wire) Disclaimer: Distances, type of wiring and gauge must be determined by a certified professional to avoid voltage drop problem. Maximum 9m (30 ft) Serial connection Maximum 9m (30 ft) Parallel connection 30 Tycos Drive, Toronto, Ontario, Canada M6B 1V9 PH: / FAX: , tech@zaneen.com

5 R Wiring Diagram Reference P DMX/DALI Parallel connection for RGB 24Vdc dimmable systems R G B DMX Interface BUS / DMX interface ECO ECO DMX control gear codes 24Vdc ALI ALI ALI ECO * R G B BUS DMX Interface BUS / ECO BUS DMX / DALI Controller * PC only needed for programming 30 Tycos Drive, Toronto, Ontario, Canada M6B 1V9 PH: / FAX: , tech@zaneen.com