Lunar zen ze i n thi h nt n er e io r rs io. rs c. o c m o

Transcription

1 Lunar

2 Lunar A workstation range with a simple understated aesthetic that is capable, adaptable, versatile and fully resolved. LUNAR WORKSTATION FEATURES This highly capable range can adapt to solve the requirements of almost any work environment. It can be configured into an extraordinarily wide number of variants with a small kit of parts, this simplifies the specification process and ensures that reconfiguring the office down the track is an easy process. Its clean, resolved and attractive lines add to the visual impact of a wide variety of office interiors. It has its own patent pending angle adjusting leg that enables it to do more with less. The structure can be assembled onsite and wired from above prior to the tops going on which significantly reduces installation cost and time, it also has fold down wire management to facilitate changes in office hardware. With 200 mm of tool less height adjustment, it offers more adjustment than the standard 150mm to ensure it works for a wide range of user sizes. FINISHES Accessories: Dulux standard colours (custom colours upon request) Tops: Laminate, Veneer (specials upon request) Frames: Dulux standard colours (custom colours upon request) S30 / S50 Screen Finish: Echo Panel, Fabric, Forbo Pinboard, Glass, Laminate, Perforated Metal, Plain Metal, Twin Wall Polycarbonate, Veneer, Whiteboard. CERTIFICATIONS DESIGN Zenith Design Studio

3 DESK LAYOUTS Lunar Workstation 90 degree 2 End Left hand 2 End Left Hand Extension 2 End Right Hand 2 End Right Hand Extension 3 End Left hand 3 End Left Hand Extension 3 End Right Hand 3 End Right Hand Extension Pod of 4 Pod 8 of Angle Leg Pod of 8 Angle Leg Extension Pod of 8 Straight Leg Pod of 8 Straight Leg Extension Lunar Workstation U shape 2 End 2 End Extension 2 x 90 Degree 2 x 90 Degree Extension 4 End 4 End Extension

4 DESK LAYOUTS Lunar Workstation 120 degree Standard U Shape U Shape Extension Pod of 3 Pod of 3 Pod of 6 Angle Leg Pod of 6 Angle Leg Extension Hex Post Type 2 Pod of 6 Angle Leg Pod of 6 Straight Leg Pod of 6 Straight Leg Extension Hex Post Type 2 Pod of 6 Straight Leg Hex Post Pod of 6 Straight Leg Extension Type 2 Hex Post Type 2 Pod of 9 Angle Leg Pod of 9 Angle Leg Hex Post Type 2 Pod of 9 Straight Leg Pod of 9 Straight Leg Hex Post Type 2

5 DESK LAYOUTS Lunar Workstation 180 degree Standard Pod of 2 Pod of 4 Angle Leg Pod of 4 Straight Leg Pod of 6 Angle Leg Pod of 6 Straight Leg Pod of 8 Angle Leg Pod of 8 Straight Leg Pod of 10 Angle Leg Pod of 10 Straight Leg Pod of 12 Angle Leg Pod of 12 Straight Leg Run of 2 Run of 3 Run of 4 Run of 5 Run of 6

6 LEG STYLES HEIGHT RANGE

7 CARE & MAINTENANCE FABRIC Gently spot clean excess liquid from the fabric surface. Do not saturate or scrub the fabric with water or cleaning liquids. Every fabric composition varies and the individual fabric supplier should be contacted for further fabric care instructions. ECHO PANEL Remove dust and marks with a soft damp cloth and mild solutions of warm water and upholstery shampoo. Blot dry with a solution free soft damp cloth. FORBO PINBOARD Clean with a damp cloth or if necessary, with a brush using a neutral detergent. Rinse with clean water. The pinboard material is resistant to diluted acids, oils and most conventional solvents such as alcohol, white spirit. LAMINATE For general cleaning use a soft clean cloth and a mild detergent in warm water. Wipe the surface gently to remove dust or marks. Always rinse after cleaning with fresh water to remove any remaining detergent. For heavier stains use a non-abrasive cleaner. Excessive scrubbing may damage the decorative surface, particularly a gloss finish. METAL For general cleaning use a soft clean cloth and a mild detergent in warm water. Wipe the surface gently to remove dust or marks. Always rinse after cleaning with fresh water to remove any remaining detergent. POWDER COAT Remove loose deposits with a wet sponge (avoid scratching the surface by dry dusting). Use a soft clean cloth and mild detergent in warm water. Wipe the powdercoating to remove dust, salt or other deposits. Always rinse after cleaning with fresh water to remove any remaining detergent. In some cases, strong solvents recommended for thinning various types of paints and also for cleaning up are harmful to the extended life of the powder coated surface. These solvents should not be used for cleaning purposes. VENEER Dust and wipe down the veneer surface regularly with a slightly damp soft cloth. Furniture polish recommended for the appropriate wood finish will remove soil and dust and provide a protective coating to guard against future spills. Polishing more than 3-4 times per year will see a buildup of cloudy film. Water or liquid spills should be wiped up immediately and avoid placing hot items directly on the veneer surface. TWIN WALL POLYCARBONATE Mild soapy water and a soft clean cloth will sufficiently remove stubborn stains or markings. Make sure the detergent contains no abrasives or solvents. Pre wash with warm water and gently rub stains. Rinse with water to remove excess residue. WHITEBOARD Use a whiteboard duster for general erasing. For tough marks (ghosting) use a professional whiteboard cleaner and wipe with soap, water and a clean cloth afterwards. To prevent ghosting, the ink should be completely dry before erasing. Excessive smearing and smudging can occur if wet ink is attempted to be erased.