CCD Barcode Scanner User s Manual Version 1.05

Size: px

Start display at page:

Download "CCD Barcode Scanner User s Manual Version 1.05"

Emma Gray
7 years ago
Views:

1 CCD Barcode Scanner User s Manual Version 1.05

2 CATALOG Program procedure using scanner menus.1 1. System Information 1.1 Restore default Show firmware version Show series number.2 2. System Setup 2.1 Interface selection Scanning mode selection Beeper tone selection Header and Trailer Bar Code Parameters Setting 3.1 UPC-A Control UPC-E Control EAN 13 Control EAN 8 Control UPC/EAN Conversion Control UPC/EAN Added Codes Control Code 39 Control Coda Bar Control Code 93 Control Code 128 Control Interleaved 2 of 5 Control Industrial 2 of 5 Control Standard 2 of 5 Control Matrix 2 of 5 Control China Postal Code Control MSI/Plessey Control 37 Appendix..39

3 1 PROGRAM PROCEDURE USING SCANNER MENUS:

4 2 SET 1. System Information 1.1 Restore default The reading of the RESET label turns all the parameters back to default values. RESET 1.2 Show firmware version The reading of the FIRMWARE VERSION label will be shown firmware version FIRMWARE 1.3 Show series number The reading of the SERIES NUMBER label will be show series number. SERIES NUMBER END

5 3 SET 2. System Setup 2.1 Interface selection There are three kinds of different interfaces to be chosen now. The scanner remains in the last interface type when the scanner is reset. * KEYBOARD /USB INTERFACE RS-232 WAND

6 4 Choose the appropriate type of keyboard emulation by scanning the labels under the following labels. *PC AT, PS/ PC XT IBM5550 SYSTEM TYPE Apple Macintosh NEC 9800 ACER 7300 END

7 5 SET * USA UK Germany French LANGUAGE SELECTION Spanish Italian Swiss Swedish

8 6 *AUTOMATISM NUM LOCK ON KEYBOARD NUM LOCK OFF CAPS LOCK ON CAPS LOCK OFF None MESSAGE TERMINATOR (for KB) *Enter Tab END

9 7 SET 1200 bps 2400 bps 4800 bps BAUD RATE (For RS-232) *9600 bps bps 57600bps 7 Bit DATA BIT (For RS-232) *8 Bit

10 8 *1Bit STOP BIT (For RS-232) 2Bit *None CHECK SET (For RS-232) EVEN CHECK ODD CHECK *None HANDSHAKING SELECTION (For RS-232) RTS/CTS XON/XOFF END

11 9 SET None *CR/LF CR MESSAGE TERMINATOR (For RS-232) LF H Tab STX/ETX EOT

12 10 *0 ms 10ms DATA DURATION 50ms 100ms *0 s 0.5s CHARACTER 1s 5s END

13 11 SET 2.2 Scanning mode selection Trigger mode The scanner becomes inactive as soon as the data is transmitted. It must be triggered to become active again. Auto scan mode The scanner is always on, put the barcode before the scan line, decode just one time. Decode again only when change barcode. If decode the same barcode once more, put it on the scan line, then scan works the second time. Alternate mode When press the scanner trigger switch once, this scanner will light up. Simultaneously, The scanner decoded only once when put the barcode on the scan line. If put the barcode on the scan line again, the scanner decoded again. Then, the scanner will turn off for next pressing. Repeat mode This mode is similar to Auto scan mode, but double reading for the same barcode is prohibited if the scanner switch is pressed. Testing mode The scanner is always on. All the while, the scanner decoded and transmitted the data when the barcode is put on scan line. Turbo trigger mode When the trigger is pressed, the scanner decoded sequentially.

14 12 *Trigger mode Auto scan mode Alternate mode SCANNING MODE SELECTION Repeat mode Testing mode Testing mode END

15 13 SET 2.3 Beeper selection Low Very low BEEPER TONE *Medium High Disable Short BEEPER SOUND DURATION *Medium Long

16 Header and Trailer This option allows you to append a header and/or a trailer to every message transmitted via the serial ports or the keyboard port. There is no restriction in selecting header or trailer characters as far as the sum of the lengths of header and trailer is not greater than 10 digits. 1. Select either header or trailer you are going to program by scanning the corresponding label 2. Scan the character you want from the enclose ASCII table to set as header or trailer. HEADER * None * None TRAILER 3. Read the SET label to set your choice into memory. END

17 15 SET 3. Barcode parameters setting 3.1 UPC-A Disable READABLE *Enable IDENTIFIER CODE TRANSMITTING CHECK DIGIT Disable *Enable Disable CUT FRONT *Enable

18 UPC-E CONTROL Disable READABLE *Enable IDENTIFIER CODE TRANSMITTING CHECK DIGIT Disable *Enable Disable CUT FRONT *Enable END

19 17 SET 3.3 EAN-13 CONTROL Disable READABLE *Enable IDENTIFIER CODE TRANSMITTING CHECK DIGIT Disable *Enable TRANSFER TO ISBN/ISSN Enable

20 EAN-8 CONTROL Disable READABLE *Enable IDENTIFIER CODE TRANSMITTING CHECK DIGIT Disable *Enable END

21 19 SET 3.5 UPC/EAN CONVERTION UPC-A TO EAN-13 CONVERSION Enable UPC-E TO UPC-A CONVERSION Enable 3.6 UPC/EAN ADDED CODE *None ADDED CODE *2 or 5 Bit

22 Code 39 Control Disable READABLE *Enable IDENTIFIER CODE CALCULATING Enable CONCATENATION Enable END

23 21 SET * Standard Code 39 PARAMETERS Full Code 39 START/STOP CHARACTER TRANSMISSION Enable 0 MIN (0~64) (*0 ) 0 MAX. (0~64)(*64) CUT FRONT 0 * CUT BACK 0 *

24 Coda Bar Control READABLE Disable *Enable IDENTIFIER CODE CALCULATING Enable TRANSMITTING CHECK DIGIT Enable END

25 23 SET *ABCD/ABCD START/STOP CHARACTER TYPE abcd/abcd abcd/tn*e START/STOP CHARACTER TRANSMISSION Enable MIN 0 A(0~64)(*5) MAX 0 A(0~64)(*64)

26 24 CUT FRONT *0 CUT BACK *0 END

27 25 SET 3.9 Code 93 Control Disable READABLE *Enable IDENTIFIER CODE CALCULATING Enable TRANSMITTING CHECK DIGIT Enable

28 26 0 MIN (0~64)(*5) 0 MAX (0~64)(*64) *0 CUT FRONT *0 CUT BACK END

29 27 SET 3.10 Code 128 Control Disable READABLE *Enable IDENTIFIER CODE Disable CALCULATING *Enable TRANSMITTING CHECK DIGIT Enable

30 28 MIN (0~64)(*0 ) 0 MAX (0~64)(*64 ) 0 *0 CUT FRONT *0 CUT BACK END

31 29 SET 3.11 Interleaved 2 of 5 Control Disable READABLE *Enable * Disable IDENTIFIER CODE * Disable CALCULATING Enable * Disable TRANSMITTING CHECK DIGIT Enable

32 30 0 MIN (0~64)(*5) 0 MAX (0~64)(*64) *0 CUT FRONT *0 CUT BACK END

33 31 SET 3.12 Industrial 2 of 5 Control Disable READABLE *Enable IDENTIFIER CODE 0 MIN (0~64)(*5 ) 0 MAX (0~64)(*64 ) CUT FRONT *0 CUT BACK *0

34 Standard 2 of 5 Control Disable READABLE *Enable IDENTIFIER CODE 0 MIN (0~64)(* 5 ) 0 MAX (0~64)(*64 ) CUT FRONT *0 CUT BACK *0 END

35 33 SET 3.14 Matrix 2 of 5 Control READABLE Enable IDENTIFIER CODE CALCULATING Enable TRANSMITTING CHECK DIGIT Enable

36 34 0 MIN (0~64)(*5) 0 MAX (0~64)(*64 ) *0 CUT FRONT *0 CUT BACK END

37 35 SET 3.15 China Postal Code Control READABLE Enable IDENTIFIER CODE CALCULATING Enable TRANSMITTING CHECK DIGIT Enable

38 36 0 MIN (0~64)(* 5) 0 MAX (0~64)(* 64) *0 CUT FRONT *0 CUT BACK END

39 37 SET 3.16 MSI/Plessey Control READABLE Enable IDENTIFIER CODE 0 MIN (0~64)(*5) 0 MAX (0~64)(*64 ) CUT FRONT *0 CUT BACK *0

40 38 *None Mode10 Transmit 0 bit Mode10 Transmit 1 bit Mode11 Transmit 0 bit CALCULATING Mode11 Transmit 1 bit Mode11 Transmit 2 bit Mode10/ Mode11 Transmit Yes Mode10/ Mode11 Transmit No END

41 Appendix 39 NUL BS SOH HT STX LF ETX VT EOT FF ENQ CR ACK SO BEL

42 40 SI ETB DLE CAN DC1 EM DC2 SUB DC3 ESC DC4 FS NAK GS SYN

43 41 RS & US SP (! ) * # + $, %

44 / : 3 ; 4

45 43 < D = E > F? H A I B J C

46 44 K S L T M U N V O W P X Q Y R

47 45 Z b [ c \ d ] e ^ f _ g ` h a

48 46 i q j r k s l t m u n v o w p

49 47 x y z { } ~ DEL

50 48

Part No. : MUL-53221-07 PROGRAMMING GUIDE

Part No. : MUL-53221-07 PROGRAMMING GUIDE PROGRAMMING GUIDE for BARCODE SCANNERS The guide can be used as keyboard emulation, RS- 232C serial interface, and USB 1.1 interface and wand emulation. IMPORTANT