Copper-Nickel Alloys for Seawater Piping Systems (CuNi 90/10 and CuNi 70/30)
|
|
- Sabina Rodgers
- 7 years ago
- Views:
Transcription
1 Shipbuilding OSNA -10 and OSNA -30 Copper-Nickel Alloys for Seawater Piping Systems (CuNi 90/10 and CuNi 70/30) KME Germany GmbH & Co. KG Shipbuilding - OSNA -10 and OSNA -30 [GB]
2 Content KME - The Company 1 The Material 2 Shipbuilding - Product Range 3 Pipes 4 Butt Welding Fittings Elbows 5 Tee Pieces (equal and reduced) 7 End Caps 10 Saddle Type Connections 11 Reducers (concentric and eccentric) 14 Flanges Welding Necks (equal and reduced) 17 Outer Flanges 18 Blind Flanges 19 Brazing Fittings Couplings (straight and reduced) 20 Elbows 22 Tee Pieces (equal and reduced) 23 End Caps 25 Male Connectors (straight) 26 Female Connectors (straight) 27 Miscellaneous Hexagon Head Screw Plugs 28 Welding Ends 29 Sockets 30 Unions 31 Male Unions (reduced) 32 KME Quality Management 36 Nightman1965,
3 KME - The Company KME as one of the largest manufacturers of copper and copper alloy products offers best possible product and engineering solutions in the various fields of industrial applications. As a leading supplier in the most diverse industries, KME serves the worlds market with a broad spectrum of technologically leading copper and copper-alloy tubes, strips and sheets of outstanding production quality. Marine Applications KME s business unit Marine Applications is specialized in the production of copper-nickel alloys for piping systems in shipbuilding, offshore installations and other marine applications. The sea and its atmosphere is one of the most corrosive environments on the earth. Seagoing vessels need large amounts of seawater daily for fire water systems sprinkler systems cooling systems ballast systems The materials used for sea water piping systems there fore must be highly resistant to pitting, crevice and erosion corrosion as well as stress corrosion cracking and macrofouling. Moreover such materials must satisfy high standards in terms of hot and cold working pro perties and weldability. KME Germany GmbH & Co. KG Shipbuilding 1
4 The Material KME Alloys OSNA -10 and OSNA -30 For decades, seawater pipe systems made of copper-nickel alloys have been put to successful use on seagoing vessels and offshore production units like plat forms, drilling rigs, semi-sub mersibles FPSOs etc. The chemical composition of OSNA -10 (CuNi 90/10) and OSNA -30 (CuNi 70/30) copper-nickel alloys have been modified so that they meet the requirements of all the main international standards (see tables below). Reduced tolerance limits for certain impurities moreover pro vide for an enhanced cold work ability and weld ability of KME s alloy. Main Advantages of OSNA -10 and OSNA -30 Despite the rough conditions in marine service and the highly corrosive nature of seawater, the products provide well balanced combination of technical and economical advantages: Simple alloying system with good weldability Excellent ductility and toughness Good erosion corrosion resistance Resistant to uniform and localised corrosion No effect of ambient seawater temperatures No effect of seawater chlorination Resistant to biofouling Resistant to stress-corrosion cracking Low maintenance costs A lot of design experience Comparison of Standard Specifications for OSNA -10 (CuNi 90/10) KME Alloy OSNA -10 (CuNi 90/10) EN 1652/ 12420/ ) CW352H DIN WL EEMUA 2016, 234/1-2 UNS C 7060 x MIL-T-16420K ASTM B 466 2) /467 C JIS H 3300 C 7060 T Ni % Fe % * Mn % max C % max max max max max Pb % max max max max max max S % max max max max max P % max max max max max Zn % max max max max max max Sn % max other imp. max max max max Cu % rem. rem. rem. rem. min Ni+Fe+Mn min ) formerly BS 2871 Part 2 2) equal to C for subsequent welding * The iron content has been specified to improve corrosion resistance Comparison of Standard Specifications for OSNA -30 (CuNi 70/30) KME Alloy OSNA -30 (CuNi 70/30) EN 1652/ 12420/ ) CW354H MIL-T-16420K ASTM B 466/467 2) C JIS H 3300 C 7150 T Ni % Fe % Mn % max C % max max max Pb % max max max max S % max max max P % max max max Zn % max max max max Sn % max other imp. max max Cu % rem. rem. min. 65 +Ni+Fe+Mn min ) formerly BS 2871 Part 2 2) equal to C for subsequent welding 2 KME Germany GmbH & Co. KG Shipbuilding
5 Shipbuilding - Product Range OSNA -10 and OSNA -30 seawater pipes are manufactured in two con figurations: seamless seamwelded OSNA -10 (CuNi 90/10) O.D. seamless, up to 1200 O.D. seam-welded International Standards EN 1652/12420/12449 DIN EEMUA 234/1-2 ASTM-B-466/467 MIL-T K JIS H 3300 OSNA -30 (CuNi 70/30) O.D. seamless, up to 1200 O.D. seam-welded International Standards EN 1652/12420/12449 (CW354H) ASTM-B-466/467 MIL-T K JIS H 3300 KME offers a comprehensive range of pipes and fittings in different sizes and dimensions for sea water piping systems in different appli cations. Furthermore, we are also offering sheets and plates in different sizes. KME Germany GmbH & Co. KG Shipbuilding 3
6 Pipes Pipes Specifications: DIN 86019, DIN EN and similar*. OSNA -10 (CuNi 90/10) and OSNA -30 (CuNi 70/30) Seamless Pipe Wall Thickness DN OD Standard Special* in S kg/m S kg/m ¹/ ¼ ³/ ½ ¾ ¼ ½ ½ (89.0) (219) (324) For offshore wall thickness see separate catalogue. Seam welded Pipe * * * * * * ) similar to 4 KME Germany GmbH & Co. KG Shipbuilding
7 Elbows Long radius 1.5 D Butt Welding Fittings Specification: DIN and similar*. OSNA copper-nickel Type and Construction: Elbows for pipes up to and including 14"/ 368 in size are normally supplied seam less. Elbows for larger diameter pipes are made from half shells, longitudinally welded. 45 and 90 elbows are available in all sizes. DN OD Wall Thickness S Radius a ~ e Weight ( ~ kg) in Seamless ½ 16 20* ¾ 20 25* ¼ ½ ½ * * * * ) similar to KME Germany GmbH & Co. KG Shipbuilding 5
8 Elbows Short radius 1.0 D Butt Welding Fittings DN OD in Seamless Wall Thickness S Radius a e Weight ( ~ kg) ¼ ½ ½ KME Germany GmbH & Co. KG Shipbuilding
9 Tee Pieces, equal Butt Welding Fittings Specification DIN and similar* Type and Construction: Tees for pipes up to and including 8"/ 219 are normally supplied as one-piece and seamless. Wall Thickness DN OD S a b Weight in kg /piece ½ 16 20* ¾ 20 25* ¼ ½ ½ * ) similar to KME Germany GmbH & Co. KG Shipbuilding 7
10 Tee Pieces, reduced 1) Butt Welding Fittings Specification DIN and similar* Type and Construction: Tees for pipes up to and including 8"/ 219 are normally supplied as one-piece and seamless. 1) final dimensions can be slightly different and can be provided on request. DN OD 1 OD 2 in Wall Thickness S 1 S 2 a b Weight kg /piece ¾ x ½ 20 x x 20* 1.5 x x ½ 25 x x 20* 1.5 x x ¾ 25 x x 25* 1.5 x ¼ x ½ 32 x x 20* 1.5 x ¼ x ¾ 32 x x 25* 1.5 x ¼ x 1 32 x x x ½ x ½ 40 x x 20* 1.5 x ½ x ¾ 40 x x 25* 1.5 x ½ x 1 40 x x x ½ x 1¼ 40 x x x x ¾ 50 x x 25* 1.5 x x 1 50 x x x x 1¼ 50 x x x x 1½ 50 x x x ½ x 1 65 x x x ½ x 1¼ 65 x x x ½ x 1½ 65 x x x ½ x 2 65 x x x x 1¼ 80 x x x x 1½ 80 x x x x 2 80 x x x x 2½ 80 x x x x 1½ 100 x x x x x x x x 2½ 100 x x x x x x x x x x x x 2½ 125 x x x x x x x x x x x x 2½ 150 x x x x x x x x x x x x x x x x x x x x x x x x x x x KME Germany GmbH & Co. KG Shipbuilding
11 Tee Pieces, reduced 1) Butt Welding Fittings DN OD 1 OD 2 in Wall Thickness S 1 S 2 a b Weight kg /piece 10 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x * ) similar to KME Germany GmbH & Co. KG Shipbuilding 9
12 End Caps Butt Welding Fittings Specification DIN DN OD S h 1 h 2 Weight in kg /piece ¼ ½ ½ ½ KME Germany GmbH & Co. KG Shipbuilding
13 Saddle Type Connections Butt Welding Fittings Specification: DIN and similar* Dimensions: To suit appropriate header and branch pipe diameters and thicknesses. Type and Construction: Saddles for pipes up to and in clu d ing 14"/ 368 are normally supplied as one-piece and seamless. Wall Thickness Height Length DN OD 1 OD 2 S 1 S 2 h L Weight in kg /piece ½ x ½ 16 x x 20* 1 x ¾ x ½ 20 x x 20* 1.5 x ¾ x ¾ 20 x x 25* 1.5 x x ¾ 25 x x 25* 1.5 x x 1 25 x x 30* 1.5 x ¼ x 1 32 x x 30* 1.5 x ¼ x 1¼ 32 x x x ½ x 1¼ 40 x x x ½ x 1½ 40 x x x x 1¼ 50 x x x x 1½ 50 x x x x 2 50 x x x ½ x 1¼ 65 x x 38 2 x ½ x 1½ 65 x x x ½ x 2 65 x x 57 2 x ½ x 2½ 65 x x 76 2 x x 1¼ 80 x x 38 2 x x 1½ 80 x x x x 2 80 x x 57 2 x x 2½ 80 x x 76 2 x x 3 80 x x 89 2 x x 1½ 100 x x x x x x x x 2½ 100 x x x x x x x x x x x * ) similar to KME Germany GmbH & Co. KG Shipbuilding 11
14 Saddle Type Connections (continued) Butt Welding Fittings Specification: DIN and similar* Dimensions: To suit appropriate header and branch pipe diameters and thicknesses. Type and Construction: Saddles for pipes up to and in clu d ing 14"/ 368 are normally supplied as one-piece and seamless. DN OD 1 OD 2 in Wall Thickness S 1 S 2 Height h Length L Weight kg /piece 5 x x x x x 2½ 125 x x x x x x x x x x x x x x x x 2½ 150 x x x x x x x x x x x x x x x x x x x x 2½ 175 x x 76* 3 x x x x 89 3 x x x x x x x x x x x x x x x x x x x x 89 3 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x KME Germany GmbH & Co. KG Shipbuilding
15 Butt Welding Fittings DN OD 1 OD 2 in Wall Thickness S 1 S 2 Height h Length L Weight kg /piece 14 x x x x x x x x x x x x x x x x x x x x x x x x x x x 159* 4 x x x x x x x x x x x x x x x x x x x x x x x x x x x x 159* 4.5 x x x x 194* 4.5 x x x x x x x x x x x x x x x x x x x x x x x x x x x x 159* 5 x x x x 194* 5 x x x x 219* 5 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x * ) similar to KME Germany GmbH & Co. KG Shipbuilding 13
16 Reducers Butt Welding Fittings Specification: DIN and similar* Type and Construction: Concentric reducers up to and in clu d ing 14"/368 are nor mally supplied as one-piece and seamless. Eccentric reducers up to and in clu d ing 14"/ 368 are nor mally supplied as one-piece and seamless. DN OD 1 OD 2 in Wall Thickness S 1 S 2 Length L Weight ½ x ³/ 8 16 x x 16* 1 x ¾ x ³/ 8 20 x x 16* 1.5 x ¾ x ½ 20 x x 20* 1.5 x x ³/ 8 25 x x 16* 1.5 x x ½ 25 x x 20* 1.5 x x ¾ 25 x x x ¼ x ³/ 8 32 x x 16* 1.5 x ¼ x ½ 32 x x 20* 1.5 x ¼ x ¾ 32 x x x ¼ x 1 32 x x x ½ x ½ 40 x x 20* 1.5 x ½ x ¾ 40 x x x ½ x 1 40 x x x ½ x 1¼ 40 x x x x ¾ 50 x x x x 1 50 x x x x 1¼ 50 x x x x 1½ 50 x x x ½ x 1 65 x x 30 2 x ½ x 1¼ 65 x x 38 2 x ½ x 1½ 65 x x x ½ x 2 65 x x 57 2 x x 1¼ 80 x x 38 2 x x 1½ 80 x x x x 2 80 x x 57 2 x x 2½ 80 x x 76 2 x x 1½ 100 x x x x x x x x 2½ 100 x x x x x x x kg /piece 14 KME Germany GmbH & Co. KG Shipbuilding
17 Butt Welding Fittings concentric eccentric DN OD 1 OD 2 in Wall Thickness S 1 S 2 Length L Weight kg /piece 5 x x x x x 2½ 125 x x x x x x x x x x x x 2½ 150 x x x x x x x x x x x x x x x x x x 89* 3 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 133* 4 x x x x x x x x x x x x x x x x x * ) similar to KME Germany GmbH & Co. KG Shipbuilding 15
18 Reducers (continued) Butt Welding Fittings concentric eccentric * ) similar to DN OD 1 OD 2 in Wall Thickness S 1 S 2 Length L Weight kg /piece 14 x x x 159* 4 x x x x x x x x x x x x x x x x x x x x 194* 4 x x x x x x x x x x x x x x x x x x x x 219* 4.5 x x x x x x x x x x x x x x x x x x x x 267* 5 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x KME Germany GmbH & Co. KG Shipbuilding
19 Welding Necks Flanges Specification: DIN compatible with Outer Flanges PN 10, 16 Type and Construction: Weld neck flanges up to and including 12"/ 324 are nor mally supplied as one-piece and seamless. DN OD in Wall Thickness S d 2 d 3 d 4 h 1 h 3 Weight kg /piece ¾ ¾ ¼ ¼ ½ ½ ½ KME Germany GmbH & Co. KG Shipbuilding 17
20 Outer Flanges Flanges Specification: DIN 86037, EN (Type 04) PN10, 16 S235JR Note: Steel flanges will be supplied hot-dip galvanized. PN 10 DN OD D d 1 b k d 2 Bolt Weight in Holes kg /piece ¾ ¼ ½ ½ PN 16 ¾ see PN KME Germany GmbH & Co. KG Shipbuilding
21 Blind Flanges Flanges Specification: EN (Type 05-C) PN 10, 16 welded glued A105/P245GH (flanges) Note: Steel flanges will be supplied readily hot-dip galvanized. DN 10 - DN 175 PN 16 DN DN 500 PN 10 DN OD in Weight kg /piece D b k d 1 d 2 Bolt Holes 3/ ½ ¾ ¼ ½ ½ KME Germany GmbH & Co. KG Shipbuilding 19
22 Couplings, straight Brazing Fittings with silver solder capillary x capillary end PN up to 63 DN OD A C L B Weight in kg /piece / ¼ ¼ / ½ / ¼ ¼ ½ KME Germany GmbH & Co. KG Shipbuilding
23 Couplings, reduced Brazing Fittings with silver solder capillary x capillary end PN up to 63 nominal actual A 1 A 2 C 1 C 2 B 1 B 2 L Weight in 10 x kg /piece x ¼ x 1/8 12 x x ¼ x 1/8 14 x / 8 x 1/8 16 x / 8 x ¼ 16x ½ x ¼ 20 x ½ x 3/8 20 x ¾ x 3/8 25 x ¾ x ½ 25 x x 3/8 30 x x ½ 30 x x ¾ 30 x ¼ x 3/8 38 x ¼ x ½ 38 x ¼ x ¾ 38 x ¼ x 1 38 x ½ x 3/ x ½ x ½ 44.5 x ½ x ¾ 44.5 x ½ x x ½ x 1¼ 44.5 x x 3/8 57 x x ½ 57 x x ¾ 57 x x 1 57 x x 1¼ 57 x x 1½ 57 x KME Germany GmbH & Co. KG Shipbuilding 21
24 Elbows Brazing Fittings with silver solder capillary x capillary end PN up to 63 DN OD A B C L N Weight in kg /piece / ¼ ¼ / ½ / ¼ ¼ KME Germany GmbH & Co. KG Shipbuilding
25 Tee Pieces, equal Brazing Fittings with silver solder capillary x capillary ends PN up to 63 DN OD A B C L N Weight in kg /piece / ¼ ¼ / ½ / ¼ ¼ KME Germany GmbH & Co. KG Shipbuilding 23
26 Tee Pieces, reduced Brazing Fittings with silver solder capillary x capillary ends PN up to 63 DN OD 1 x OD 2 A 1 A 2 C 1 C 2 B 1 B 2 N L Weight in kg /piece 1/ 8 6 x 4 10 x ¼ 8 x 4 12 x ¼ x 1/8 8 x 6 12 x ¼ 10 x 4 14 x ¼ x 1/8 10 x 6 14 x / 8 x 1/8 12 x 6 16 x / 8 x ¼ 12 x 8 16 x ½ x ¼ 16 x 8 20 x ½ x 3/8 16 x x / 4 x 3/8 20 x x / 4 x ½ 20 x x x 3/8 25 x x x ½ 25 x x x 3/4 25 x x ¼ x 3/8 32 x x ¼ x ½ 32 x x ¼ x 3/4 32 x x ¼ x 1 32 x x ½ x 3/8 40 x x ½ x ½ 40 x x ½ x 3/4 40 x x ½ x 1 40 x x ½ x 1¼ 40 x x x ½ 50 x x x 3/4 50 x x x 1 50 x x x 1¼ 50 x x x 1½ 50 x x KME Germany GmbH & Co. KG Shipbuilding
27 End Caps Brazing Fittings with silver solder capillary end PN up to 63 DN OD A B H Weight in kg /piece / ¼ ¼ / ½ / ¼ ¼ KME Germany GmbH & Co. KG Shipbuilding 25
28 Straight Male Connectors Brazing Fittings E (male BSP thread) capillary end x male thread section view Outside Diameter of Pipe nominal in actual x E" A B C L 1 L 2 A/F Weight kg /piece 1/ 8 x ½ 10 x ½ / 8 x ¾ 10 x ¾ ¼ x ½ 12 x ½ ¼ x ¾ 12 x ¾ ¼ x ½ 14 x ½ ¼ x ¾ 14 x ¾ ¼ x 1 14 x / 8 x 3/8 16 x 3/ / 8 x ½ 16 x ½ / 8 x ¾ 16 x ¾ / 8 x 1 16 x ½ x ½ 20 x ½ ½ x ¾ 20 x ¾ ½ x 1 20 x ½ x 1¼ 20 x 1¼ ¾ x ¾ 25 x ¾ ¾ x 1 25 x ¾ x 1¼ 25 x 1¼ ¾ x 1½ 25 x 1½ x ¾ 30 x ¾ x 1 30 x x 1¼ 30 x 1¼ x 1½ 30 x 1½ ¼ x ¾ 38 x ¾ ¼ x 1 38 x ¼ x 1¼ 38 x 1¼ ¼ x 1½ 38 x 1½ ½ x x ½ x 1¼ 44.5 x 1¼ ½ x 1½ 44.5 x 1½ ½ x x x 1¼ 57 x 1¼ x 1½ 57 x 1½ x 2 57 x x 2½ 57 x 2½ KME Germany GmbH & Co. KG Shipbuilding
29 Straight Female Connectors Brazing Fittings E (male BSP thread) capillary end x female thread section view Outside Diameter of Pipe nominal in actual xe" A B C d 2 L 1 L 2 A/F Weight kg /piece 1/ 8 x ½ 10 x ½ / 8 x ¾ 10 x ¾ ¼ x ½ 12 x ½ ¼ x ¾ 12 x ¾ ¼ x ½ 14 x ½ ¼ x ¾ 14 x ¾ ¼ x 1 14 x / 8 x 3/8 16 x 3/ / 8 x ½ 16 x ½ / 8 x ¾ 16 x ¾ / 8 x 1 16 x ½ x ½ 20 x ½ ½ x ¾ 20 x ¾ ½ x 1 20 x ½ x 1¼ 20 x 1¼ ¾ x ¾ 25 x ¾ ¾ x 1 25 x ¾ x 1¼ 25 x 1¼ ¾ x 1½ 25 x 1½ x ¾ 30 x ¾ x 1 30 x x 1¼ 30 x 1¼ x 1½ 30 x 1½ ¼ x ¾ 38 x ¾ ¼ x 1 38 x ¼ x 1¼ 38 x 1¼ ¼ x 1½ 38 x 1½ ½ x x ½ x 1¼ 44.5 x 1¼ ½ x 1½ 44.5 x 1½ ½ x x x 1¼ 57 x 1¼ x 1½ 57 x 1½ x 2 57 x x 2½ 57 x 2½ KME Germany GmbH & Co. KG Shipbuilding 27
30 Hexagon Head Screw Plugs Miscellaneous Specification: DIN 910 d 1 (thread) G* 1/8 G d 2 14 l 8 L 17 A/F 10 Weight kg /piece G ¼ G ¼ /8 G /8 G G ½ G ½ /4 G /4 G G G 11/ G 1¼ G 1½ G 13/ G KME Germany GmbH & Co. KG Shipbuilding
31 Welding Ends Miscellaneous section view DN OD S d 3 L l 1 Weight in (thread) G kg /piece /8 G / G ¼ ¼ /8 G ½ G ½ / /4 G G ¼ G 1¼ ½ G 1½ G ½ G 2½ G KME Germany GmbH & Co. KG Shipbuilding 29
32 Sockets Miscellaneous with Whitworth thread Specification: DIN PN 40 up to 225 C section view d 1 (thread) in d 2 b 1 l 1 Weight kg /piece G ¼ /8 G G ½ G ½ G ½ G ½ G ½ /4 G /4 G /4 G /4 G /4 G G G G G G G 1¼ G 1½ G KME Germany GmbH & Co. KG Shipbuilding
33 Unions Miscellaneous with silver solder capillary x capillary ends equiped with sealing ring PN up to 63 section view Outside Diameter of Pipe nominal in actual xg" A C ~ L ~ L 1 A/F A/F 1 Weight kg /piece / ¼ ¼ / ½ ¾ ¼ ½ KME Germany GmbH & Co. KG Shipbuilding 31
34 Male Unions Miscellaneous with silver solder capillary x male thread equiped with sealing ring PN up to 63 section view Outside Diameter of Pipe nominal in actual xg" A C d 1 (Thread) G" ~ L ~ L 1 ~ L 2 A/F 1 A/F 2 Weight kg /piece 8 x ¼ 12 6 G ¼ / 8 10 x 3/ G 3/ ¼ 12 x ½ G ½ ¼ 14 x 5/ G 5/ / 8 16 x ¾ G ¾ ½ 20 x G ¾ 25 x G x 1 ¼ G 1¼ ¼ 38 x 1½ G 1½ ½ 44.5 x 1¾ G 1¾ x 2½ G 2½ KME Germany GmbH & Co. KG Shipbuilding
35 Male Unions, reduced Miscellaneous with silver solder capillary x male thread equiped with sealing ring PN up to 63 section view Outside Diameter of Pipe nominal in actual xg" A C d 1 (Thread) G" ~ L ~ L 1 ~ L 2 A/F 1 A/F 2 Weight kg /piece 8 x 1/ Gx ½ x 3/ Gx 3/ x ½ 12 6 Gx ½ / 8 10 x ¼ 15 6 Gx ¼ / 8 10 x ½ 15 8 Gx ½ / 8 10 x 5/ Gx 5/ ¼ 12 x ¼ 17 6 Gx ¼ ¼ 12 x 3/ Gx 3/ ¼ 12 x 5/ Gx 5/ ¼ 12 x ¾ Gx ¾ ¼ 14 x 3/ Gx 3/ ¼ 14 x ½ Gx ½ ¼ 14 x ¾ Gx ¾ ¼ 14 x Gx / 8 16 x ½ Gx ½ / 8 16 x 5/ Gx 5/ / 8 16 x 1¾ Gx / 8 16 x 1¼ Gx 1¼ ½ 20 x 5/ Gx 5/ ½ 20 x ¾ Gx ¾ ½ 20 x 1¼ Gx 1¼ ½ 20 x 1½ Gx 1½ ¾ 25 x 5/ Gx 5/ ¾ 25 x ¾ Gx ¾ ¾ 25 x 1¼ Gx 1¼ ¾ 25 x 1½ Gx 1½ KME Germany GmbH & Co. KG Shipbuilding 33
36 Male Unions, reduced (continued) Miscellaneous with silver solder capillary x male thread equiped with sealing ring PN up to 63 section view Outside Diameter of Pipe nominal in actual xg" A C d 1 (Thread) G" ~ L ~ L 1 ~ L 2 A/F 1 A/F 2 Weight kg /piece 1 30 x ¾ G x ¾ x G x x 1½ G x 1½ x 1¾ G x 1¾ ¼ 38 x ¾ G x ¾ ¼ 38 x G x ¼ 38 x 1¼ G x 1¼ ¼ 38 x 1¾ G x 1¾ ½ 44.5 x G x ½ 44.5 x 1¼ G x 1¼ ½ 44.5 x 1½ G x 1½ ½ 44.5 x G x x 1¼ G x 1¼ x 1½ G x 1½ x 1¾ G x 1¾ x G x KME Germany GmbH & Co. KG Shipbuilding
37
38 36 KME Germany GmbH & Co. KG Shipbuilding
39 KME Quality Management KME is coitted to the continuous improvement of all our business and production processes in terms of efficiency, effectiveness and reliability as regards their organisation, technological aspects and staff management. The aim of our coitment is to increase the satisfaction of all stakeholders. We are constantly engaged in: creating products of outstanding quality preventing errors and defects minimising the costs associated with errors and inefficiencies preventing the waste of resources establishing safe production conditions to protect both our employees and the environment We aim for excellence by means of transparent management systems designed to satisfy the requirements of our clients together with the demands of the market and technology. The quality management systems implemented throughout the KME Group are fully compliant with the provisions of ISO 9001 as well as, in the case of our automotive industry clients, ISO TS , and our staff is strongly coitted to their implementation at all levels. KME Germany GmbH & Co. KG Shipbuilding 37
40 KME Germany GmbH & Co. KG Marine Applications P.O. Box OSNABRÜCK Klosterstraße OSNABRÜCK GERMANY Fon Marine Applications = registered trademark All changes reserved. Owing to limitations in printing technology, the colours reproduced in this brochure should be regarded as approximate equivalents to the colours described Photo title: Carabay,
Seawater corrosion resistant piping systems for large diameters up to 100 / 2.5 metres O.D.
OSNA -10 Copper-Nickel Lined Pipes Seawater corrosion resistant piping systems for large diameters up to 100 / 2.5 metres O.D. KME Germany AG & Co. KG Copper-Nickel Lined Pipes [GB] Member of the KME Group
More informationCopper and Copper Alloy Tube, Pipe and Fittings
Copper and Copper Alloy Tube, Pipe and Fittings COPPER and COPPER ALLOY TUBE and PIPE Seamless Copper Pipe: Copper pipe is almost pure copper manufactured to the requirements of ASTM B 42 - Standard Specification
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationHose and Tube Fittings Series 1-3
Embracing Challenge Hose and Tube Fittings Series 1-3 out of plastics PP, PVDF, PTFE Series 1 Special Features Corrosion resistant Gas tight Easy to handle Different connection threads Application Hose
More informationMetal Pressfitting Pipe Systems
VdS Guidelines for water extinguishing systems VdS 2100-26-3en Requirements and test methods Part 3: Additional provisions for Pipe Systems made of galvanized steel VdS 2100-26-3en : 2012-04 (01) Publishing
More informationBUMAX. REYHER your partner for the BUMAX range
BUMAX high-tensile stainless steel fasteners REYHER your partner for the BUMAX range Strongest stainless steel fasteners in the world BUMAX 88 and BUMAX ready for delivery from stock Wide range of BUMAX
More informationGENERAL PROPERTIES //////////////////////////////////////////////////////
ALLOY 625 DATA SHEET //// Alloy 625 (UNS designation N06625) is a nickel-chromium-molybdenum alloy possessing excellent resistance to oxidation and corrosion over a broad range of corrosive conditions,
More informationRING JOINT SYSTEMS 207
RING JOINT SYSTEMS 07 08 Table of Contents Model R-88 Pages 10-11 Model R-88 Large Diameter Page 1 Model RH-1000 1000 PSI Coupling Page 13 Model RX-3000 3000 PSI Coupling Page 1 Model RX-3770 3770 PSI
More informationCaps STANDARD WEIGHT Inches / Pounds
Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe
More informationHYDRAULIC PIPING STANDARD HANDBOOK. Revision 1
HYDRAULIC PIPING STANDARD HANDBOOK Revision 1 Preface We aim to fill a gap in technical literature. At this moment there are no hydraulic piping standards available which cover different pressure classes
More informationGAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES
GAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES CONTINENTAL INDUSTRIES ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and is today
More informationBypass level indicator With magnetic display Model BNA
Level measurement Bypass level indicator With magnetic display Model BNA WIKA data sheet LM 10.01 Applications Continuous level indication without power supply Indication of the level proportional to height
More information2013 Edition. Flanged fittings 30"-64" NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61
30"-64" Ductile Iron industrial Applications, water & Wastewater 2 Table of Contents Flanged Fittings for Water 3 Flange Details 5 Flanged Fittings 6 90º and 45º Bend 6 22-1/2º and 11-1/4º Bends 7 Tees
More informationASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.
ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.4-1998 - Cast Iron Threaded Fittings ASME/ANSI B16.5-1996 - Pipe
More informationJIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes
JIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes 1. Scope This Japanese Industrial Standard specifies the electric resistance welded carbon steel tubes, hereinafter
More informationCopper-Nickel Mill Products
Copper-Nickel Mill Products Copper-Nickel Rod, Sheet, Plate, and Tubing ALASKAN COPPER & BRASS COMPANY History W hen Alaskan Copper Works was founded as a marine coppersmithing company in 9, one of its
More information% Si Fe Cu Mn Mg Cr Zn Ti Others Others. Europe USA Spain France Germany G.B. Italy Sweden Switzerland Japan. ALMgSi1 3.3215 H30
ALUMINIUMS Alloys Aluminium - Magnesium - Silicon 6082 % Si Fe Cu Mn Mg Cr Zn Ti Others Others Minimum 0,70 0,40 0,60 Each Total Maximum 1,30 0,50 0,10 1,00 1,20 0,25 0,20 0,10 0,05 0,10 Europe USA Spain
More informationStainless Steel Tubular Products
Stainless Steel Tubular Products r Disclaimer This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary
More informationNorth American Stainless
North American Stainless Long Products Stainless Steel Grade Sheet 2205 UNS S2205 EN 1.4462 2304 UNS S2304 EN 1.4362 INTRODUCTION Types 2205 and 2304 are duplex stainless steel grades with a microstructure,
More informationGALVANIC CATHODIC PROTECTION 1.0 CONTENTS. 1.1 Aluminium Anodes. 1.2 Zinc Anodes. 1.3 Magnesium Anodes SECTION
SECTION 1 GALVANIC CATHODIC PROTECTION 1.0 CONTENTS 1.1 Aluminium Anodes 1.1.1 Aluminium Tank Anodes 1.1.2 Aluminium Hull Anodes 1.1.3 Aluminium Platform / Jetty Anodes 1.2 Zinc Anodes 1.2.1 Zinc Tank
More informationAfrica s leading steel supplier CATALOGUE TUBE & PIPE. The Macsteel Group - Africa s leading steel supplier - www.macsteel.co.za
Africa s leading steel supplier CATALOGUE TUBE & PIPE - www.macsteel.co.za TUBE & PIPE CONTENTS 1. Contents 13. Conveyance SANS 1182 - Light Page 7 2. Contact Details 14. Conveyance SANS 719 - Large Bore
More information4. Combi valves. 7. Fire hydrants. 8. Check valves. 9. Air valves
1. General company and product information 2. Flanged gate valves for water 3. Other gate valves for water 4. Combi valves 5. Service connection valves for water 6. Valves and fittings for gas 7. Fire
More informationRely on Our Material Competence for Your Demanding Industrial Processes
Cast Materials Rely on Our Material Competence for Your Demanding Industrial Processes Our customer-focused R&D and continuous research on new material options enable us to develop equipment with a strong
More informationMicro Motion Model D and DL Coriolis Flow and Density Meters
Product Data Sheet PS-00388, Rev. F April 2013 Micro Motion Model D and DL Coriolis Flow and Density Meters Micro Motion Model D and DL sensors provide flow and density measurement for liquids, gases,
More informationVdS 2100-09en. VdS Guidelines for water extinguishing systems. Non-return valves. Requirements and test methods. VdS 2100-09en : 2011-05 (01)
VdS Guidelines for water extinguishing systems VdS 2100-09en Requirements and test methods VdS 2100-09en : 2011-05 (01) Publishing house: VdS Schadenverhütung GmbH Amsterdamer Str. 172-174 50735 Köln,
More informationwww.klmtechgroup.com TABLE OF CONTENT
Page : 1 of 10 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia TABLE OF CONTENT SCOPE 2 REFERENCES
More informationTARIFF CODE and updates standard
TARIFF CODE and updates standard No HS CODE AHTN CODE PRODUCT DESCRIPTION PRODUCT TYPE STANDARDS IDENTIFIED 7207 Semi finished products of iron or non alloy steel Containing by weight less than 0.25% of
More informationTYPE APPROVAL CERTIFICATE
DET NORSKE VERITAS TYPE APPROVAL CERTIFICATE CERTIFICATE NO. P-14862 This is to certify that the Pipe System with Couplings with type designation(s) Megapress with SC-contour Issued to Viega GmbH & Co.
More informationIndustrial Tubes Made from Copper and Copper Alloys
TECTUBE Industrial Tubes Made from Copper and Copper Alloys KME Germany GmbH & Co. KG TECTUBE [GB] Industrial Tubes The most important customers for KME Industrial Tubes are found in the refrigeration
More informationPIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification. 96 B. Riutta
PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification Number: 3503-11.2.610 Rev. 2 Rubber Lined Steel Pipe and Fittings Mechanically Coupled Plain End Type System Issued Revised Approved
More informationDiwiTherm, Resistance Thermometers Model TR75, with digital Display Battery or Solar Powered
Electrical Temperature Measurement DiwiTherm, Resistance Thermometers Model TR75, with digital Display Battery or Solar Powered WIKA Data Sheet TE 60.75 Applications Machinery, plant and tank construction
More informationGrey cast iron Fig. 600 Page 2. Forged steel High temperature steel Stainless steel Fig. 600/601 (Y) DN15-25 Page 4 DN40-50 Page 6
Bimetallic steam trap CONA B Bimetallic steam trap Bimetallic steam trap PN16 - with flanges (Fig. 600...1) - union with butt weld ends (Fig. 600...5) Grey cast iron Fig. 600 Page 2 Bimetallic steam trap
More information08. SEK IDC CONNECTORS
. IDC CONNECTORS connectors for flat cables enable simple and, cost-optimized device configuration. connectors are preferably used for connection within the device. HARTING offers a broad range of these
More informationSeamless stainless tubes for hydraulic and instrumentation systems
Seamless stainless tubes for hydraulic and instrumentation systems stock assortment integrated production technical knowledge network of sales and service Reduce your lifecycle costs When selecting tubes
More informationGeberit Mapress Catalogue 2008 / 2009. Valid from 1 April 2008
Geberit Mapress Catalogue 2008 / 2009 Vali from 1 April 2008 Mapress Stainless Steel Page 3 Mapress CrNi Steel Page 23 Mapress Stainless Steel silicone-free Page 25 Mapress Stainless Steel Gas Page 39
More informationBRASS FITTINGS FOR THREADED PIPES
03/14 BRASS FITTINGS GENERAL FEATURES The brass fittings for threaded pipes are used as junctions for pipelines with threaded connection UNI ISO 228/1. The thread dimensions are subdivided in various types
More informationJIS G3461 Carbon Steel Tubes for Boiler and Heat Exchanger
JIS G3461 Carbon Steel Tubes for Boiler and Heat Exchanger 1. Scope This Japanese Industrial Standard specifies the carbon steel tubes, hereinafter referred to as the "tubes", used for exchanging heat
More informationStainless steel grade chart
Stainless steel grade chart ATLAS STEELS METAL DISTRIBUTION Chemical analysis (%) specified C Si Mn P S Cr Mo Ni Other Austenitic stainless steels 253MA S30815 0.05 1.1-2.0 0.8 0.040 0.030 20.0-22.0 10.0-12.0
More informationTHERMA-TUBE preinsulated pipes and fittings Catalogue of products
THERMA-TUBE preinsulated pipes and fittings Catalogue of products THERMA TUBE preinsulated pipes and fittings TABLE OF CONTENTS 1. GENERAL INFORMATION ABOUT THE USE OF PREINSULATED PIPES AND FITTINGS...
More informationNorth American Stainless
North American Stainless Long Products Stainless Steel Grade Sheet AISI 316 UNS S31600 EN 1.4401 AISI 316L UNS S31630 EN 1.4404 INTRODUCTION NAS provides 316 and 316L SS, which are molybdenum-bearing austenitic
More informationSports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049
Sports and High Mast Lighting Poles 4 High Mast Lighting Poles General American LitePole offers a raising and lowering system that allows for ease of maintaining the lighting system at ground level. Ideal
More informationAlternative Steel Materials to BS 5950
BC 1: 2008 Design Guide on Use of Alternative Steel Materials to BS 5950 BCA Sustainable Construction Series 3 The education and research arm of the Building and Construction Authority 200 Braddell Road
More informationPressure Vessel Assessment Report
Project Information Client: Total Energy Location: Blackwell OK Date: 7/23/2013 Contact: Integrity Mgmt. Advisor: Chuck Easterbrooks - API 510 #2212 Cc: API / UT Inspector: Robert Van Pelt-API 510# 40899
More informationASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :-
Standard Specification for Wrought High Strength Ferritic Steel Butt Welding Fittings 1. Scope :- 1.1 This specification covers wrought high strength ferritic steel butt-welding fitting of seamless and
More informationALLOY 2205 DATA SHEET
ALLOY 2205 DATA SHEET UNS S32205, EN 1.4462 / UNS S31803 GENERAL PROPERTIES ////////////////////////////////////////////////////// //// 2205 (UNS designations S32205 / S31803) is a 22 % chromium, 3 % molybdenum,
More informationHK Trading Import Export e.k. is a family owned German company. Founded in 2004 HK Trading has established itself as a notable trading company.
HK Trading Import Export e.k. is a family owned German company. Founded in 2004 HK Trading has established itself as a notable trading company. Based on superb and fair business relationships to long-standing
More informationNIPPON STEEL & SUMITOMO METAL SEAMLESS STEEL LINE PIPE
Pipe Products NIPPON STEEL & SUMITOMO METAL SEAMLESS STEEL LINE PIPE http://www.nssmc.com/ 2-6-1 Marunouchi, Chiyoda-ku,Tokyo 100-8071 Japan Tel: +81-3-6867-4111 SEAMLESS STEEL LINE PIPE P103en_01_201211f
More informationFLEXWELL Safety Pipe. Pipe systems for installations Technical details
Pipe systems for installations Technical details Notes 08.04.2013 T page 2 Contents 4.0 4.0 Contents 4.1 System description 4.100 System description FLEXWELL Safety Pipe 4.105 System description FLEXWELL
More informationNEW CONNECTION INDUSTRIAL PRODUCTS NC.10V NC.20V NC.30V. NC. SD.10 NC. SD.20 NC. F.Clamp
Repair and Construction. Complete stainless steel pipe repair clamps to repair cracks, fractures, pin holes, torn sockets or welded tees, broken asbest-cement pipe coupling and more. Available for all
More informationA New Improved Range of Push-fit Fittings for Cold Water Services
A New Improved Range of Push-fit Fittings for Cold Water Services A new improved range of Push-fit Fittings for Cold Water Services, with Stainless Steel Teeth to grip the pipe Push-fit Fittings for Cold
More informationTECHNICAL SPECIFICATION
THOMAS - G-FLEX GFLEX TECH SPEC CONNECTING INNOVATION JOHANNESBURG TEL: +27 11 794 7594 CAPE TOWN TEL: +27 21 556 5258 POLOKWANE TEL: 015 298 9142 DESIGNER, MANUFACTURER AND DISTRIBUTOR OF PIPE CONNECTION,
More informationTG 105 ALLOWABLE PIPE SIZE, CLASS AND MATERIALS FOR WATER MAINS TECHNICAL GUIDELINE. Manager Asset Management SOUTH AUSTRALIAN WATER CORPORATION
TG 105 SOUTH AUSTRALIAN WATER CORPORATION TECHNICAL GUIDELINE ALLOWABLE PIPE SIZE, CLASS AND MATERIALS FOR WATER MAINS Issued by: Manager Asset Management Issue Date: SA WATER 2007 This document is copyright
More informationNorth American Stainless
North American Stainless Flat Products Stainless Steel Grade Sheet 310S (S31008)/ EN 1.4845 Introduction: SS310 is a highly alloyed austenitic stainless steel designed for elevated-temperature service.
More informationGPD Rubber Press Seals
GPD Rubber Press Seals Leading in in ideas SYSTEM-TECHNIK GPD Rubber Press Seals Design Available with a rubber thickness of 30 mm for sealing against non-pressing water and a rubber thickness of 60 mm
More informationNickel Alloys, Stainless Steel and Other Corrosion Resistant Alloys ALASKAN COPPER & BRASS COMPANY
Bosses and Welding Outlets Branch Outlets in Copper-Nickel, Nickel Alloys, Stainless Steel and Other Corrosion Resistant Alloys ALASKAN COPPER & BRASS COMPANY T he various Alaskan Copper and Brass Company
More information20 TANK CONTAINER STANDARD SPECIFICATION MODEL NUMBER: 24 FSTD 2 QUOTATION NUMBER
REVISION: R0 DATE: 04/04/00 20 TANK CONTAINER STANDARD SPECIFICATION MODEL NUMBER: 24 FSTD 2 QUOTATION NUMBER PROPOSED BY: PREPARED FOR: TRENCOR TANK CONTAINERS - 1 - OPERATOR/ OWNER: 1. Technical Characteristics
More informationPC/104, PC/104 -Plus, VarPol connectors
164 PC/104, PC/104 -Plus, VarPol connectors Definitions 166 Technical specifications 168 Hole specifications 169 PC/104 170 PC/104-Plus 172 Accessories: PC/104 and PC/104-Plus 174 VarPol angled pin header
More informationHose Clamps & Fittings
All Stainless Steel Marine or Underground Hose Clamps 5/16 HEX HEAD SCREW 60000 SERIES Highly corrosion resistant Use for marine or underground applications Stainless Steel Band, Housing Plated Steel Screw
More informationNorth American Stainless
North American Stainless Flat Product Stainless Steel Grade Sheet 316 (S31600)/EN 1.4401 316L (S31603)/ EN 1.4404 INTRODUCTION NAS provides 316 and 316L SS, which are molybdenum-bearing austenitic stainless
More informationSTRAUB-PLAST-PRO Technical Manual
STRAU-PLAST-PRO Technical Manual Contents STRAU-PLAST-PRO 3 Properties 3 Example 3 The full set 4 components 5 Conntectors 5 Pipe dimensions and tolerances 5 straub-plast-pro l Coupler 6 straub-plast-pro
More informationNorth American Stainless
Introduction: North American Stainless Flat Products Stainless Steel Grade Sheet 309S (S30908)/ EN1.4833 SS309 is a highly alloyed austenitic stainless steel used for its excellent oxidation resistance,
More informationkymanual or Automatic - it s your Choice
. kymanual or Automatic - it s your Choice ky LKB Automatic or Manual Butterfly Valve Application LKB is a sanitary automatically or manually operated butterfly valve for use in stainless steel pipe systems.
More informationIndex. 2.40 mm Connector Series. 2.40 mm Connectors (50 GHz)... Page. Interface Standards... 44. Specifications... 45. Connector Numbers...
Connector Series Index (50 GHz).... Page Interface Standards... 44 Specifications... 45 Connector Numbers... 46 Typical Test Data... 48 End : can be found in the Adapter section. : can be found in the
More information2-Port Self-acting Temperature Control Valve Selection for Heating and Cooling Applications
Page 1 of 12 TI-S21-07 CH Issue 1 Cert. No. LRQ 0963008 ISO 9001 2-Port Self-acting Temperature Control Valve Selection How to select a system Valve selection: 1. Is the application for heating or cooling?
More information60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
More informationCajon VCR Fittings. Flanges, Fittings, & Components. Cajon & Swagelok Fittings. Cajon VCR Fittings. Nuts, Caps, & Plugs. Socket Weld Glands
Cajon VCR Fittings Cajon VCR Fittings Make excellent low-pressure gas connections Ideal for lecture bottle gas cylinders, standard helium checks, and general gas plumbing Withstand bakeout to 58º C (with
More informationGrooved gaskets. Types of gaskets
Types of gaskets have proven extremely useful in all areas of industry, including the most demanding sealing tasks. Our grooved gaskets can be found in conventional power plants as well as in the primary
More information14 PHOENIX CONTACT Courtesy of Power/mation. 1310 Energy Lane, Saint Paul, MN 55108. info@powermation.com - 800-843-9859 - www.powermation.
14 PHOENIX CONTACT PLUSCON circular is a circular connector for use in industrial automation. The range of design sizes available is varied, starting with the design sizes M5 to M8 and M1, for sensor/actuator
More informationLIST PRICE BOOK MALLEABLE CAST IRON PRESS FITTINGS FOR SCH. 10 40 BLACK & GALVANIZED STEEL PIPE
FASTLOCK fittings are not currently approved for use with gas or fire protection applications. FITTINGS FOR STEEL PIPE LIST PRICE BOOK MALLEABLE CAST IRON FITTINGS FOR SCH. 10 40 BLACK & GALVANIZED STEEL
More informationDirectory chapter 04
M Directory chapter 04 D-Sub Mixed subminiature D connectors New Page D-Sub mixed connector system general information................... 04.02 Contact arrangements............................................
More informationAISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels
AISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels AISI No. 1008 1010 1012 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 10 1026 1027 1029 10 1035 1036 1037 1038 1039 10 1041 1042 1043
More informationMaterial data sheet. EOS StainlessSteel GP1 for EOSINT M 270. Description, application
EOS StainlessSteel GP1 for EOSINT M 270 A number of different materials are available for use with EOSINT M systems, offering a broad range of e-manufacturing applications. EOS StainlessSteel GP1 is a
More informationJIS G3445 Carbon steel tubes for machine structural purposes
JIS G3445 arbon steel tubes for machine structural purposes 1. Scope This Japanese Industrial Standard specifies the carbon steel tubes, hereinafter referred to as the "tubes", used for machinery, automobiles,
More informationGK Packing System Welding Instructions
GK Packing System Welding Instructions Roxtec GmbH Neuer Höltigbaum 1-3, 22143 Hamburg GERMANY Tel +49 (040) 657398-0, Fax +49 (040) 657398-50 EMAIL info@de.roxtec.com, www.roxtec.de Welding instructions
More informationDX2202 Duplex stainless steel
Stainless Europe Grade DX22 Duplex stainless steel Chemical Composition Elements C Mn Cr Ni Mo N %.25.3 23. 2.5
More informationData Sheet VITOSOL 100. Flat collectors for the utilisation of solar energy. Vitosol 100. Part nos. and prices: see price list
VITOSOL 100 Flat collectors for the utilisation of solar energy Data Sheet Part nos. and prices: see price list File in: Vitotec 1 Manual, Index 16 Vitosol 100 Type s 1.7 Vitosol 100 Type s 2.5 Vitosol
More informationVSH Press Sprinkler Galvanized System
www.vsh-fittings.com VSH Press Sprinkler Galvanized System VSH Fittings Netherlands 09 VSH Fittings B.V. Post Box 498 1200 AL Hilversum The Netherlands Tel. +31 (0)35 688 42 11 Fax +31 (0)35 688 43 79
More informationDARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
SECTION 15062 STEAM AND CONDENSATE PIPING PART 1 DESIGN DIRECTIVES 1.1 QUALITY ASSURANCE A. Comply with the provisions of the following: 1.2 DESIGN CRITERIA 1. ASME B 31.9 Building Services Piping : for
More informationTubing Data. Contents. Tubing Selection. Tubing Handling. Tubing Material. Tubing Outside Diameter Hardness. Tubing Wall Thickness
www.swagelok.com Tubing Data Contents Tubing Selection... 1 Tubing Handling.... 1 Gas Service... 2 Tubing Installation.... 2 Suggested Allowable Working Pressure Tables Carbon Steel Tubing... 3 Stainless
More informationBritish Standard Underground Hydrant Range
British Standard Underground Hydrant Range 2 THE NEW AVK BRITISH STANDARD HYDRANT RANGE AVK are the renowned market leading innovators, manufacturers and suppliers of BS 750 fire hydrants into the UK,
More informationBROEN UNiFlEx FiTTiNgs FOR BURNiNg gases OEN OEN ifl ifl FOR FOR BURN BURN gas gas
BROEN UNIFLEX Fittings FOR BURNIN ASES BROEN UniFlex TM Fittings for burning gases BROEN UniFlex TM Fittings for burning gases LAB Table of Contents Content Page Table of Content 2 Product Overview 3 BROEN
More informationQuick Connect Boxes Inside Gloveboxes
ULC Series Junction Boxes Quick Connect Boxes Inside Gloveboxes The ULC quick connect junction boxes are the essential elements to optimize the cabling inside gloveboxes. Large range Designed for nuclear
More informationGYROLOK to Tube Union
GYROLOK HOKE manufactured GYROLOK tube fittings have been carefully designed and manufactured to provide a wide range of outstanding leak-tight application capabilities. GYROLOK to Tube Union MANUFACTURED
More informationTECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR
TECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR 1.1.0 SCOPE : This specification covers design, manufacture, testing at manufacture s works before
More informationNorth American Stainless
North American Stainless Flat Products Stainless Steel Grade Sheet 430 (S43000)/ EN 1.4016 Introduction: SS430 is a low-carbon plain chromium, ferritic stainless steel without any stabilization of carbon
More informationSelf-operated Temperature Regulators Temperature Regulator Type 1u
Self-operated Temperature Regulators Temperature Regulator Type u Application Temperature regulators for cooling installations Control thermostats for set points ) from 0 to 250 C G ½ to G or DN 5 to 50
More informationProfiles in stock Standard catalogue. Discover the possibilities with aluminium profiles from Sapa
Profiles in stock Standard catalogue Discover the possibilities with aluminium from Sapa You can create your own profile or you can choose from a wide selection of standard. Delivery: 1 2 weeks for standard
More informationBall valve C 16 valve ball completely moulded in place, extremely low clearance volume, high k v value
Ball valve C valve ball completely moulded in place, extremely low clearance volume, high k v value Advantage maximum safety due to valve ball completely moulded in place - ball and ball seat cannot be
More informationVALVES FOR REFRIGERATING SYSTEMS
VALVES FOR REFRIGERATING SYSTEMS FROM QUALITY OUR NATURAL DEVELOPMENT Achieved the goal of fi fty years working in the industry of Refrigeration and Air Conditioning, Castel Quality Range of Products is
More informationSchedule 40 & Schedule 80 Rigid PVC Piping Systems Scroll Down for Dimensions, Components, Hangars & Supports, Fabrication Techniques
Schedule 40 & Schedule 80 Rigid PVC Piping Systems Scroll Down for Dimensions, Components, Hangars & Supports, Fabrication Techniques Schedule 40 Rigid PVC Piping Systems SCHEDULE 40 - DIMENSIONS Harvel
More informationUNIVERSAL RAILING, STEEL
RAILINGS Page Universal Railing, steel 108-109 Large Module Railing, steel 110-111 Allround Railing, aluminium 112-113 Module Railing, aluminium 114-115 Standard Type Railing, aluminium 116-117 107 UNIVERSAL
More informationCarbon and stainless steel pipes/tubes for mechanical engineering and structural applications
Carbon and stainless steel pipes/tubes for mechanical engineering and structural applications ThyssenKrupp Materials Austria ThyssenKrupp Our service for you. The area of materials management is placing
More informationSPIRAL WOUND GASKETS Driven by the industry's need for safe, effective sealing solutions, Flexitallic invented the spiral wound gasket.
innovate/customize/educate SPIRAL WOUND GASKETS Driven by the industry's need for safe, effective sealing solutions, Flexitallic invented the spiral wound gasket. www.flexitallic.eu FLEXITALLIC The Flexitallic
More informationSECTION 15140 - PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
More informationProduct Catalogue Australian Plumbing Fittings
Capillary Sizes ELBOWS - 90 Degree J08123 15mm x 15mm 90Deg LE Cu SR ELB F+F (No. 12) J08131 18mm x 18mm 90Deg LE Cu ELB F+F (No. 12) J08145 20mm x 20mm 90Deg LE Cu SR ELB F+F (No. 12) J08147 20mm x 15mm
More informationSpira-trol TM Two-port Control Valves EN Standard KE, KF and KL DN15 to DN300 and ASME Standard KEA, KFA and KLA ½" to 12"
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationSECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS
SECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS PART 1 GENERAL 1.01 SECTION INCLUDES A. The requirements for pipe material and installation in sewer and drainage collection systems. All materials
More information