UG130: Si86xxT-EVB User's Guide
|
|
|
- Sophia Wiggins
- 7 years ago
- Views:
Transcription
1 The Si864xxT devices, the latest addition to the Si86xx isolator family, are 4-channel CMOS-based galvanic digital isolators surge rated at 10 kv. Operating up to 150 Mbps, they are available in wide body 16-pin SOIC packages and designed for the stringent isolation needs of the industrial, commercial, and automotive markets. Various channel configurations dictating the number of reverse channels and default output states are also available per the Si86xx data sheet s ordering guide. The Si864xxT-EVB allows designers to quickly evaluate the Si8642ET s capabilities and functionality, either by driving inputs to logic low via shunts, or injecting signals to the header pins via single wires or a 2x6 ribbon cable (not included). KEY POINTS Discusses kit contents and equipment. Describes hardware setup and demonstration. Shows EVB schematic and layout. Includes bill of materials and the ordering guide for Si864xxT-KIT. For more information on our Si86xxT isolators, visit the Silicon Labs website at: The product data sheet and application notes can be referenced to help facilitate designs. silabs.com Smart. Connected. Energy-friendly. Rev. 0.1
2 Kit Contents 1. Kit Contents The Si864xxT Evaluation Kit contains the following items: Si864xxT-EVB evaluation board, shown in the figure below. Si8642ET-IS, 4-channel (Reverse: 3 and 4), 150 Mbps, 10 kv, Wide Body, Default High I/O. Figure 1.1. Si86xxT-EVB silabs.com Smart. Connected. Energy-friendly. Rev
3 Required Equipment 2. Required Equipment The following equipment is required to demonstrate the evaluation board: Two DC Power supplies V, 100 ma. (Optionally) Isolated from one another. Four banana-to-test-clip cables with clips to supply power to the board. Two 2-pin header shunts (included). One DMM. One DMM Voltage Probe Set. 2.1 Optional Equipment The following equipment is optional and can be used to demonstrate more of the evaluation board functionalities, including signal propagation statistics: One Signal generator. Two BNC Coaxial cables. One BNC splitter. One BNC to test-clip connector. One 2-Channel Oscilloscope. One 10x Voltage Probe. silabs.com Smart. Connected. Energy-friendly. Rev
4 Hardware Setup and Demonstration 3. Hardware Setup and Demonstration 3.1 Powering the Supplies Both sides of the Si8642ET isolator accept supplies between V. See the figure below. Perform the following steps to set up the Si864xxT-EVB: Remove all shunts. Power Side-A. Clip 5.0 V from the first power supply to TP1 (VDD1) and its GND to TP3 or TP5 (GND1). LED, D1, will light up, confirming power is supplied. Power Side-B. Clip 5.0 V from the second power supply to TP2 (VDD2) and its GND to TP4 or TP6 (GND2). LED, D2, will light up, confirming power is supplied. Figure 3.1. EVB Powered Up 3.2 DC Signal Demonstration Defaults The default output signal state of the Si8642ET is a logic High, meaning that with all shunts removed (EN1 and EN2 floating), all digital inputs (A1, A2, B3, B4) and all digital outputs will (B1, B2, A3, A4) will be at their respective High voltage level. These values can be measured and confirmed using the DMM. Remove all shunts. Measure with the DMM that all digital inputs (A1, A2, B3, B4) are logic High. Measure with the DMM that all digital outputs (B1, B2, A3, A4) are logic High. See Figure 3.1 EVB Powered Up on page 3. silabs.com Smart. Connected. Energy-friendly. Rev
5 Hardware Setup and Demonstration Fail-safes When power is removed from one side of the isolator, the outputs at the other side of the isolator default to logic High. A-side Remove all shunts. Remove A-side power supply. Measure B-side outputs, B1 and B2 and see that they are logic High. Replace A-side power and see B1 and B2 driven to their appropriate states. B-side Remove all shunts. Remove B-side power supply. Measure A-side outputs, A3 and A4 and see that they are logic High. Replace B-side power and see A3 and A4 drive to their appropriate states. Figure 3.2. EVB Failsafe, No VDDA silabs.com Smart. Connected. Energy-friendly. Rev
6 Hardware Setup and Demonstration Configured For an example, see the figure below. Place a shunt across J1 at A2. This produces a logic Low input on forward channel A2. The SI88642ET will transmit this to the B-side, and the corresponding logic Low can be observed and measured with the DMM on J2, B2. Place a shunt across J2 at B3. This produces a logic Low input on reverse channel B3. The SI88642ET will transmit this to the A-side, and the corresponding logic Low can be measured with the DMM on J1, A3. Figure 3.3. EVB Configured for DC Signal Demonstration without Enable silabs.com Smart. Connected. Energy-friendly. Rev
7 Hardware Setup and Demonstration Utilizing Enable For an example, see the figure below. Place a shunt across J1 at A2. This produces a logic Low input on forward channel A2. The SI88642ET will transmit this to the B-side, and the corresponding logic Low can be observed and measured with the DMM on J2, B2. Place a shunt across J2 at EN2. This drives EN2 to a logic Low input which tri-states outputs B1 and B2. A Hi-Z output can be observed on outputs B1 and B2 with the DMM (appearing as a high), even while A1 is a logic Low and A2 is a logic High. Figure 3.4. EVB Configured for DC Signal Demonstration with Enable silabs.com Smart. Connected. Energy-friendly. Rev
8 Hardware Setup and Demonstration 3.3 Optional Dynamic Signal Demonstration Note: Logic inputs should NOT exceed the respective VDD. For an example, see the figure below. Remove all shunts. Setup signal generator and oscilloscope. Generate 0 V to VDD1 peak, square wave (up to 300 MHz, but within the oscilloscope s capabilities) on the signal generator. Split the signal generator output to two separate BNC cables via the splitter. Attach one BNC cable end to oscilloscope Channel 1 and configure the channel for 1x gain. Attach the 10x oscilloscope probe to oscilloscope channel 2 configure the channel for 10x gain. Connect the remaining BNC cable end to the BNC-to-test-clip adapter. Clip the signal generator s output to A2 relative to GND1 (via either TP5 or TP3). Clip the oscilloscope probe s signal line on B1 and reference to GND2 (via either TP4 or TP6). Observe Channel 1 (input A2) and Channel 2 (output B2) on the oscilloscope for various parametrics such as skew and jitter. Figure 3.5. EVB Configured for Dynamic Signal Demonstration without Enable silabs.com Smart. Connected. Energy-friendly. Rev
9 Schematics 4. Schematics Figure 4.1. Si86xxT-EVB Schematic silabs.com Smart. Connected. Energy-friendly. Rev
10 Layout 5. Layout Figure 5.1. EVB Top Silk Figure 5.2. EVB Bottom Silk silabs.com Smart. Connected. Energy-friendly. Rev
11 Layout Figure 5.3. EVB Top Copper Figure 5.4. EVB Bottom Copper silabs.com Smart. Connected. Energy-friendly. Rev
12 Bill of Materials 6. Bill of Materials Table 6.1. Si86xxT-EVB Bill of Materials Item No. Quantity Reference Value Manufacturer PN Manufacturer 1 2 C1, C4 1 μf CL21B105KBFNNNE Samsung 2 2 C2, C3 0.1 μf C0603X7R K Venkel 3 2 D1, D2 RED LTST-C190KRKT LITE-ON TECHNOLOGY CORP 4 2 J1, J2 HEADER 6x2 TSW T-D Samtec 5 2 JS1, JS2 Jumper Shunt SNT-100-BK-T Samtec 6 1 PCB1 Si864xxT-EVB REV 1.0 Si864xxT-EVB REV 1.0 SiLabs 7 2 R1, R2 10K CR W-103J Venkel 8 12 R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R CR W-4990F Venkel 9 4 SF1, SF2, SF3, SF4 BUMPER SJ61A6 3M 10 2 TP1, TP2 WHITE RC Kobiconn 11 4 TP3, TP4, TP5, TP6 BLACK RC Kobiconn 12 1 U1 Si8642ET Si8642ET-IS SiLabs silabs.com Smart. Connected. Energy-friendly. Rev
13 Ordering Guide 7. Ordering Guide Ordering Part Number (OPN) Si864xxT-KIT Description Si8642ET 4-channel 10 kv Isolator Evaluation Kit silabs.com Smart. Connected. Energy-friendly. Rev
14 Smart. Connected. Energy-Friendly Products Quality Support and Community community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world s most energy friendly microcontrollers", Ember, EZLink, EZMac, EZRadio, EZRadioPRO, DSPLL, ISOmodem, Precision32, ProSLIC, SiPHY, USBXpress and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX USA
Figure 1. 8-Bit USB Debug Adapter
8-BIT USB DEBUG ADAPTER USER S GUIDE 1. Introduction The 8-bit USB Debug Adapter (UDA) provides the interface between the PC s USB port and the Silicon Labs 8-bit target device s in-system debug/programming
TS1005 Demo Board COMPONENT LIST. Ordering Information. SC70 Packaging Demo Board SOT23 Packaging Demo Board TS1005DB TS1005DB-SOT
REVISION NOTE The current revision for the TS1005 Demo Boards display the identifier TS100x Demo Board on the top side of the evaluation board as depicted in Figure 1. If the identifier is not printed
AN486: High-Side Bootstrap Design Using ISODrivers in Power Delivery Systems
AN486: High-Side Bootstrap Design Using ISODrivers in Power Delivery Systems Silicon Labs ISOdrivers are isolated gate drivers that combine low latency, high-drivestrength gate drive circuits with on-chip
AN111: Using 8-Bit MCUs in 5 Volt Systems
This document describes how to incorporate Silicon Lab s 8-bit EFM8 and C8051 families of devices into existing 5 V systems. When using a 3 V device in a 5 V system, the user must consider: A 3 V power
AN952: PCIe Jitter Estimation Using an Oscilloscope
AN952: PCIe Jitter Estimation Using an Oscilloscope Jitter of the reference clock has a direct impact on the efficiency of the data transfer between two PCIe devices. The data recovery process is able
AN962: Implementing Master-Slave Timing Redundancy in Wireless and Packet- Based Network Applications
AN962: Implementing -Slave Timing Redundancy in Wireless and Packet- Based Network Applications Robust synchronization distribution schemes have historically been essential to communication networks and
AN803. LOCK AND SETTLING TIME CONSIDERATIONS FOR Si5324/27/ 69/74 ANY-FREQUENCY JITTER ATTENUATING CLOCK ICS. 1. Introduction
LOCK AND SETTLING TIME CONSIDERATIONS FOR Si5324/27/ 69/74 ANY-FREQUENCY JITTER ATTENUATING CLOCK ICS 1. Introduction As outlined in the Product Bulletin*, issued in January 2013, Silicon Labs has made
AN862. OPTIMIZING Si534X JITTER PERFORMANCE IN NEXT GENERATION INTERNET INFRASTRUCTURE SYSTEMS. 1. Introduction
OPTIMIZING Si534X JITTER PERFORMANCE IN NEXT GENERATION INTERNET INFRASTRUCTURE SYSTEMS 1. Introduction To realize 100 fs jitter performance of the Si534x jitter attenuators and clock generators in real-world
Figure 1. Proper Method of Holding the ToolStick. Figure 2. Improper Method of Holding the ToolStick
TOOLSTICK PROGRAMMING ADAPTER USER S GUIDE 1. Handling Recommendations The ToolStick Base Adapter and daughter cards are distributed without any protective plastics. To prevent damage to the devices or
UG103.8: Application Development Fundamentals: Tools
UG103.8: Application Development Fundamentals: Tools This document provides an overview of the toolchain used to develop, build, and deploy EmberZNet and Silicon Labs Thread applications, and discusses
AN580 INFRARED GESTURE SENSING. 1. Introduction. 2. Hardware Considerations
INFRARED GESTURE SENSING 1. Introduction Touchless user interfaces are an emerging trend in embedded electronics as product designers seek out innovative control methods and more intuitive ways for users
AN922: Using the Command Line Interface (CLI) for Frequency On-the-Fly with the Si5346/47
AN922: Using the Command Line Interface (CLI) for Frequency On-the-Fly with the Si5346/47 Clockbuilder Pro comes with a command line interface (CLI)that can be used for adjusting the configuration of Si534x/8x
Making Prototyping Boards for the EFM32 kits
Making Prototyping Boards for the EFM32 kits AN0031 - Application Note Introduction This application note describes how anyone can make their own custom prototyping boards that can be connected directly
UG103-13: Application Development Fundamentals: RAIL
UG103-13: Application Development Fundamentals: RAIL Silicon Labs RAIL (Radio Abstraction Interface Layer) provides an intuitive, easily-customizable radio interface layer that is designed to support proprietary
AN614 A SIMPLE ALTERNATIVE TO ANALOG ISOLATION AMPLIFIERS. 1. Introduction. Input. Output. Input. Output Amp. Amp. Modulator or Driver
A SIMPLE ALTERNATIVE TO ANALOG ISOLATION AMPLIFIERS 1. Introduction Analog circuits sometimes require linear (analog) signal isolation for safety, signal level shifting, and/or ground loop elimination.
UG129: ZigBee USB Virtual Gateway Reference Design (RD-0002-0201) User's Guide
UG129: ZigBee USB Virtual Gateway Reference Design (RD-0002-0201) User's Guide The ZigBee USB Virtual Gateway Reference Design (RD-0002-0201) is designed to demonstrate ZigBee gateway functionality with
AN583: Safety Considerations and Layout Recommendations for Digital Isolators
AN583: Safety Considerations and Layout Recommendations for Digital Isolators This application note details the creepage and clearance requirements of an isolator type component, such as a digital isolator,
RoHs compliant, Pb-free Industrial temperature range: 40 to +85 C Footprint-compatible with ICS552-02 1.8, 2.5, or 3.3 V operation 16-TSSOP
1:8 LOW JITTER CMOS CLOCK BUFFER WITH 2:1 INPUT MUX (
Current Digital to Analog Converter
Current Digital to Analog Converter AN0064 - Application Note Introduction This application note describes how to use the EFM32 Current Digital to Analog Converter (IDAC), a peripheral that can source
ETRX3USB ETRX3USB-LRS ETRX3USB+8M ETRX3USB-LRS+8M PRODUCT MANUAL
Telegesis ETRX3USB TG-PM-0518-ETRX357USB r4 Product Manual Telegesis is a trademark of Silicon Laboratories Inc. ZigBee USB STICKS: ETRX3USB ETRX3USB-LRS ETRX3USB+8M ETRX3USB-LRS+8M PRODUCT MANUAL 2015
Bootloader with AES Encryption
...the world's most energy friendly microcontrollers Bootloader with AES Encryption AN0060 - Application Note Introduction This application note describes the implementation of a bootloader capable of
CP2110-EK CP2110 EVALUATION KIT USER S GUIDE. 1. Kit Contents. 2. Relevant Documentation. 3. Software Setup
CP2110 EVALUATION KIT USER S GUIDE 1. Kit Contents The CP2110 Evaluation Kit contains the following items: CP2110 Evaluation Board RS232 Serial Cable USB Cable DVD Quick Start Guide 2. Relevant Documentation
Table 1. RF Pico Boards of the EZRadioPRO Development Kits. Qty Description Part Number
EZRADIOPRO DEVELOPMENT KITS USER S GUIDE 1. Kits Overview This user's guide describes the development kits of the EZRadioPRO wireless development kit family. Each kit contains two RF nodes based on the
Digital Isolator Evolution Drives Optocoupler Replacement
Digital Isolator Evolution Drives Optocoupler Replacement Introduction Optocouplers have existed in various forms since the late 1960s and find use in many different applications. Because optocouplers
Connect the EFM32 with a Smart Phone through the Audio Jack
...the world's most energy friendly microcontrollers Connect the EFM32 with a Smart Phone through the Audio Jack AN0054 - Application Note Introduction This application note describes how to connect the
CPU. PCIe. Link. PCIe. Refclk. PCIe Refclk. PCIe. PCIe Endpoint. PCIe. Refclk. Figure 1. PCIe Architecture Components
AN562 PCI EXPRESS 3.1 JITTER REQUIREMENTS 1. Introduction PCI Express () is a serial point-to-point interconnect standard developed by the Peripheral Component Interconnect Special Interest Group (PCI-SIG).
ZigBee-2.4-DK 2.4 GHZ ZIGBEE DEVELOPMENT KIT USER S GUIDE. 1. Kit Contents. Figure 1. 2.4 GHz ZigBee Development Kit
2.4 GHZ ZIGBEE DEVELOPMENT KIT USER S GUIDE 1. Kit Contents The 2.4 GHz ZigBee Development Kit contains the following items, shown in Figure 1. 2.4 GHz 802.15.4/ZigBee Target Boards (6) Antennas (6) 9
Backup Power Domain. AN0041 - Application Note. Introduction
Backup Power Domain AN0041 - Application Note Introduction This application note describes how to use the EFM32 Backup Power Domain and Backup Real Time Counter. An included software example for the Giant
Si861x/2x Data Sheet. Low-Power Single and Dual-Channel Digital Isolators
Low-Power Single and Dual-Channel Digital Isolators Silicon Lab's family of ultra-low-power digital isolators are CMOS devices offering substantial data rate, propagation delay, power, size, reliability,
Telegesis is a trademark of Silicon Laboratories Inc. Telegesis ZigBee Communications Gateway. Product Manual
Telegesis ZigBee Communications Gateway TG-PM-510 ZigBee Communications Gateway Product Manual 0510r6 Telegesis is a trademark of Silicon Laboratories Inc. Telegesis ZigBee Communications Gateway Product
AN588 ENERGY HARVESTING REFERENCE DESIGN USER S GUIDE. 1. Kit Contents. 2. Introduction. Figure 1. Energy Harvesting Sensor Node
ENERGY HARVESTING REFERENCE DESIGN USER S GUIDE 1. Kit Contents The RF to USB Reference Design contains the following items: Si1012 Energy Harvesting Wireless Sensor Node EZRadioPRO USB Dongle ToolStick
AN75. Si322X DUAL PROSLIC DEMO PBX AND GR 909 LOOP TESTING SOFTWARE GUIDE. 1. Introduction
Si322X DUAL PROSLIC DEMO PBX AND GR 909 LOOP TESTING SOFTWARE GUIDE 1. Introduction Silicon Laboratories has developed example software for the Si3220/Si3225 Dual ProSLIC. The source code itself is available
How To Develop A Toolstick
TOOLSTICK BASE ADAPTER USER S GUIDE 1. Handling Recommendations To enable development, the ToolStick Base Adapter and daughter cards are distributed without any protective plastics. To prevent damage to
M68EVB908QL4 Development Board for Motorola MC68HC908QL4
M68EVB908QL4 Development Board for Motorola MC68HC908QL4! Axiom Manufacturing 2813 Industrial Lane Garland, TX 75041 Email: Sales@axman.com Web: http://www.axman.com! CONTENTS CAUTIONARY NOTES...3 TERMINOLOGY...3
CAN bus ESD protection diode
Rev. 04 15 February 2008 Product data sheet 1. Product profile 1.1 General description in a small SOT23 (TO-236AB) Surface-Mounted Device (SMD) plastic package designed to protect two automotive Controller
Evaluation Board for the AAT1275 Boost Converter with USB Power Switch
Introduction EVALUATION BOARD DATA SHEET The AAT1275 evaluation board provides a platform for test and evaluation of the AAT1275 switching boost converter with USB Power Switch. The evaluation board demonstrates
AN437. Si4432 RF PERFORMANCE AND FCC COMPLIANCE TEST RESULTS. 1. Introduction. 2. Relevant Measurements to comply with FCC
Si4432 RF PERFORMANCE AND FCC COMPLIANCE TEST RESULTS 1. Introduction This document provides measurement results and FCC compliance results for the Si4432B when operated from 902 928 MHz. The measurement
Using the High Input Voltage Charger for Single Cell Li-Ion Batteries (KIT34671EPEVBE)
Freescale Semiconductor User s Guide Document Number: KT3467UG Rev..0, 3/008 Using the High Input Voltage Charger for Single Cell Li-Ion Batteries (KIT3467EPEVBE) Purpose This User Guide helps the Lithium-Ion
XPort Universal Demo Board User Guide
XPort Universal Demo Board User Guide Part Number 900-563 Revision A September 2009 Copyright and Trademark Contacts 2009 Lantronix. All rights reserved. No part of the contents of this book may be transmitted
UM1613 User manual. 16-pin smartcard interface ST8034P demonstration board. Introduction
User manual 16-pin smartcard interface ST8034P demonstration board Introduction The purpose of this document is to describe, and provide information on, how to efficiently use the ST8034P smartcard interface
PESDxU1UT series. 1. Product profile. Ultra low capacitance ESD protection diode in SOT23 package. 1.1 General description. 1.
Rev. 02 20 August 2009 Product data sheet 1. Product profile 1.1 General description Ultra low capacitance ElectroStatic Discharge (ESD) protection diode in a SOT23 (TO-236AB) small SMD plastic package
PC Base Adapter Daughter Card UART GPIO. Figure 1. ToolStick Development Platform Block Diagram
TOOLSTICK VIRTUAL TOOLS USER S GUIDE RELEVANT DEVICES 1. Introduction The ToolStick development platform consists of a ToolStick Base Adapter and a ToolStick Daughter card. The ToolStick Virtual Tools
CryptoAuth Xplained Pro
CryptoAuth Xplained Pro CryptoAuthentication Xplained Pro Extension Board HARDWARE USER GUIDE Atmel CryptoAuth Xplained Pro Extension Board Introduction The Atmel CryptoAuth Xplained Pro (CAXPro) Evaluation
USER GUIDE EDBG. Description
USER GUIDE EDBG Description The Atmel Embedded Debugger (EDBG) is an onboard debugger for integration into development kits with Atmel MCUs. In addition to programming and debugging support through Atmel
APPLICATION. si32library. Callback CMSIS HARDWARE. Figure 1. Firmware Layer Block Diagram
PRECISION32 SOFTWARE DEVELOPMENT KIT CODE EXAMPLES OVERVIEW 1. Introduction The Precision32 code examples are part of the Software Development Kit (SDK) installed with the Precision32 software package
QSG108: Blue Gecko Bluetooth Smart Software Quick-Start Guide
QSG108: Blue Gecko Bluetooth Smart Software Quick-Start Guide Blue Gecko Bluetooth Smart Software Quick-Start Guide This document walks you through the architecture and APIs of the Blue Gecko Bluetooth
Si52144 PCI-EXPRESS GEN 1, GEN 2, & GEN 3 QUAD OUTPUT CLOCK GENERATOR. Features. Applications. Description. Functional Block Diagram
PCI-EXPRESS GEN 1, GEN 2, & GEN 3 QUAD OUTPUT CLOCK GENERATOR Features PCI-Express Gen 1, Gen 2, Gen 3, and Gen 4 common clock compliant Gen 3 SRNS Compliant Supports Serial ATA (SATA) at 100 MHz Low power,
MFRD52x. Mifare Contactless Smart Card Reader Reference Design. Document information
Rev. 2.1 17. April 2007 Preliminary Data Sheet Document information Info Keywords Content MFRC522, MFRC523, MFRC52x, MFRD522, MFRD523, Mifare Contactless Smart Card Reader Reference Design, Mifare Reader
DATASHEET. ADAM Arduino Display Adaptor Module. Arduino Compatible Shield P/N: 4Display-Shield-FT843 For the 4D Systems 4DLCD-FT843 Display
DATASHEET ADAM Arduino Display Adaptor Module Arduino Compatible Shield P/N: 4Display-Shield-FT843 For the 4D Systems 4DLCD-FT843 Display Document Date: 8 th January 2014 Document Revision: 1.0 Uncontrolled
SKY16406-381LF: 2.2-2.8 GHz Two-Way, 0 Degrees Power Divider
DATA SHEET SKY16406-381LF: 2.2-2.8 GHz Two-Way, 0 Degrees Power Divider Applications TD-LTE systems Satellite communications 2.4 GHz ISM band Features Low insertion loss: 0.3 db @ 2.5 GHz High isolation:
SMARTCARD XPRO. Preface. SMART ARM-based Microcontrollers USER GUIDE
SMART ARM-based Microcontrollers SMARTCARD XPRO USER GUIDE Preface Atmel SMARTCARD Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. Atmel SMARTCARD Xplained Pro is designed
Selecting the Right MCU Can Squeeze Nanoamps out of Your Next Internet of Things Application
Selecting the Right MCU Can Squeeze Nanoamps out of Your Next Internet of Things Application www.silabs.com Introduction Industry leaders predict that the number of connected devices for the Internet of
AN10850. LPC1700 timer triggered memory to GPIO data transfer. Document information. LPC1700, GPIO, DMA, Timer0, Sleep Mode
LPC1700 timer triggered memory to GPIO data transfer Rev. 01 16 July 2009 Application note Document information Info Keywords Abstract Content LPC1700, GPIO, DMA, Timer0, Sleep Mode This application note
UG103.8 APPLICATION DEVELOPMENT FUNDAMENTALS: TOOLS
APPLICATION DEVELOPMENT FUNDAMENTALS: TOOLS This document provides an overview of the toolchain used to develop, build, and deploy EmberZNet and Silicon Labs Thread applications, and discusses some additional
Genesi Pegasos II Setup
Freescale Semiconductor Application Note AN2666 Rev. 0, 07/2004 Genesi Pegasos II Setup by Maurie Ommerman CPD Applications Freescale Semiconductor, Inc. Austin, TX This application note is the first in
WHITE PAPER. LVDS Flat Panel Display Interface on Intel Desktop Boards. July 2009 Order Number: E77911-001
WHITE PAPER LVDS Flat Panel Display Interface on Intel Desktop Boards July 2009 Order Number: E77911-001 Revision History Revision Revision History Date 1.0 Initial release of the LVDS Flat Panel Interface
Accuracy maintained over the entire operating temperature and voltage range Low Power Consumption
I 2 C TEMPERATURE SENSORS Features High Accuracy Temperature Sensors Si7051: ±0.1 C (max) Si7053: ±0.3 C (max) Si7054: ±0.4 C (max) Si7055: ±0.5 C (max) Si7050: ±1.0 C (max) Wide operating voltage (1.9
Touchless switch Object detection Handsets Intrusion/tamper detection. Reflectance-Based Proximity Detection PRX. Signal processing SREN
OPTICAL PROXIMITY DETECTOR Features High-performance proximity detector with a sensing range of up to 50 cm Single-pulse sensing mode for low system power Adjustable detection threshold and strobe frequency
CS4525 Power Calculator
1. OVERVIEW CS4525 Power Calculator The CS4525 Power Calculator provides many important application-specific performance numbers for the CS4525 based on user-supplied design parameters. The Power Calculator
UG103.14: Application Development Fundamentals: Bluetooth Smart Technology
UG103.14: Application Development Fundamentals: Bluetooth Smart Technology This volume of Silicon Labs Application Development Fundamentals series provides an overview of Bluetooth Smart, also known as
AN3332 Application note
Application note Generating PWM signals using STM8S-DISCOVERY Application overview This application user manual provides a short description of how to use the Timer 2 peripheral (TIM2) to generate three
PRTR5V0U2F; PRTR5V0U2K
Rev. 02 19 February 2009 Product data sheet 1. Product profile 1.1 General description Ultra low capacitance double rail-to-rail ElectroStatic Discharge (ESD) protection devices in leadless ultra small
USB Audio Simplified
USB Audio Simplified The rapid expansion of the universal serial bus (USB) standard in consumer electronics products has extended the use of USB connectivity to propagate and control digital audio. USB
SKY13380-350LF: 20 MHz-3.0 GHz High Power SP4T Switch With Decoder
DATA SHEET SKY13380-350LF: 20 MHz-3.0 GHz High Power SP4T Switch With Decoder Applications GSM/WCDMA/EDGE datacards and handsets Mobile high power switching systems Features Broadband frequency range:
Design Challenges for Adding Relative Humidity Sensors
Design Challenges for Adding Relative Humidity Sensors Introduction As more and more electronic components are finding their way into outdoor equipment and remote locations, the need for environmental
DCDC-USB. 6-34V 10A, Intelligent DC-DC converter with USB interface. Quick Installation Guide Version 1.0c P/N DCDC-USB
DCDC-USB 6-34V 10A, Intelligent DC-DC converter with USB interface Quick Installation Guide Version 1.0c P/N DCDC-USB Introduction The DCDC-USB is a small yet powerful DC-DC power supply designed to power
AN655 R ANGE TEST APPLICATION FOR EZRADIO AND EZRADIOPRO. 1. Introduction. 2. Supported Radio Types
R ANGE TEST APPLICATION FOR EZRADIO AND EZRADIOPRO 1. Introduction The range evaluation demo provides an easy way to evaluate the link budget of EZRadio and EZRadioPRO devices by performing a range test
AN3353 Application note
Application note IEC 61000-4-2 standard testing Introduction This Application note is addressed to technical engineers and designers to explain how STMicroelectronics protection devices are tested according
UM1075 User manual. ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32. Introduction
User manual ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 Introduction The ST-LINK/V2 is an in-circuit debugger/programmer for the STM8 and STM32 microcontroller families. The single wire
TTL to RS232 Adapter User Guide
TTL to RS232 Adapter User Guide Revision D March 28, 2011 Document Part Number GC-800-313d Copyright and Trademark Copyright 2006-2011, Grid Connect, Inc. All rights reserved. No part of this manual may
How To Make An Electric Static Discharge (Esd) Protection Diode
Rev. 01 0 October 2008 Product data sheet 1. Product profile 1.1 General description Ultra low capacitance bidirectional ElectroStatic Discharge (ESD) protection diodes in small Surface-Mounted Device
DEMO MANUAL DC1338B LTC2990 I 2 C Temperature Voltage and Current Monitor DESCRIPTION
DEMO MANUAL DC8B LTC990 I C Temperature Voltage and Current Monitor DESCRIPTION Demonstration circuit 8B features the LTC 990, a high performance temperature, voltage and current monitor that uses I C
MN3310 Evaluation Kit v1 User Guide
1 Evaluation Kit Introduction The MN3310 Evaluation Kit is designed to allow the user to quickly evaluate the Micro Modular Technologies MN3310 GPS receiver module. The evaluation kit can be used in either
High-speed switching diodes. Type number Package Configuration Package NXP JEITA JEDEC
Rev. 8 18 November 2010 Product data sheet 1. Product profile 1.1 General description, encapsulated in small Surface-Mounted Device (SMD) plastic packages. Table 1. Product overview Type number Package
DC Motor Driver 24V 20A [RKI-1340]
![DC Motor Driver 24V 20A [RKI-1340]](/thumbs/40/21821300.jpg "DC Motor Driver 24V 20A [RKI-1340]")
DC Motor Driver 24V 20A [RKI-1340] Users Manual Robokits India info@robokits.co.in http://www.robokitsworld.com Page 1 Add raw power and simple connectivity to your robotics applications with this 24V
MN1010 Evaluation Kit v3 User Guide
1 Evaluation Kit Introduction The MN1010 Evaluation Kit is designed to allow the user to quickly evaluate the Micro Modular Technologies MN1010 GPS receiver module. This kit can be used in either a laboratory
ABB Drives. User s Manual. Pulse Encoder Interface Module RTAC-01
ABB Drives User s Manual Pulse Encoder Interface Module RTAC-0 Pulse Encoder Interface Module RTAC-0 User s Manual 3AFE 64486853 REV A EN EFFECTIVE:.5.00 00 ABB Oy. All Rights Reserved. Safety instructions
Analog to Digital Converter
Analog to Digital Converter AN0021 - Application Note Introduction This application note describes how to use the EFM32 Analog to Digital Converter to convert an analog input voltage to a digital value.
CoolWave r 2 Phase Control Board and Cable Replacement Kits
Instruction Sheet P/N 1102452A CoolWave r 2 Phase Control Board and Cable Replacement Kits Two kits are available to replace the CoolWave 2 phase control board: S S Phase Control Board and Cable Kit (required
Figure 1. Classes of Jitter
A PRIMER ON JITTER, JITTER MEASUREMENT AND PHASE-LOCKED LOOPS 1. Introduction As clock speeds and communication channels run at ever higher frequencies, engineers who have previously had little need to
+Denotes lead-free and RoHS-compliant.
19-4040; Rev 0; 2/08 MAX7474 Evaluation Kit General Description The MAX7474 evaluation kit (EV kit) is a fully assembled and tested printed-circuit board (PCB) that configures the MAX7474 IC for automatically
BAT54 series SOT23 Schottky barrier diodes Rev. 5 5 October 2012 Product data sheet 1. Product profile 1.1 General description
SOT2 Rev. 5 5 October 2012 Product data sheet 1. Product profile 1.1 General description Planar with an integrated guard ring for stress protection, encapsulated in a small SOT2 (TO-26AB) Surface-Mounted
Switch board datasheet EB007-00-1
Switch board datasheet EB007-00-1 Contents 1. About this document... 2 2. General information... 3 3. Board layout... 4 4. Testing this product... 5 5. Circuit description... 6 Appendix 1 Circuit diagram
AN104 I NTEGRATING KEIL 8051 TOOLS INTO THE SILICON LABS IDE. 1. Introduction. 2. Key Points. 3. Create a Project in the Silicon Labs IDE
I NTEGRATING KEIL 8051 TOOLS INTO THE SILICON LABS IDE 1. Introduction This application note describes how to integrate the Keil 8051 Tools into the Silicon Labs IDE (Integrated Development Environment).
Manual Serial PCI Cards
Manual Serial PCI Cards W&T Models 13011, 13410 13411, 13610 13611, 13812 Version 1.4 Subject to error and alteration 37 01/2005 by Wiesemann & Theis GmbH Subject to errors and changes: Since we can make
AN2680 Application note
Application note Fan speed controller based on STDS75 or STLM75 digital temperature sensor and ST72651AR6 MCU Introduction This application note describes the method of defining the system for regulating
UniPi technical documentation REV 1.1
technical documentation REV 1.1 Contents Overview... 2 Description... 3 GPIO port map... 4 Power Requirements... 5 Connecting Raspberry Pi to UniPi... 5 Building blocks... 5 Relays... 5 Digital Inputs...
AN335 USB DRIVER INSTALLATION UTILITY. 1. Description. 2. Installation. 2.1. Install Package
USB DRIVER INSTALLATION UTILITY 1. Description The driver installer and uninstaller combination is a customizable installation utility for Silicon Laboratories USB drivers. These utilities are completely
Features + REFCLK CLKOUT. Si5013 + DATAOUT DATAIN LOS LTR RESET/CAL CLKDSBL LOS_LVL REXT SLICE_LVL BER_LVL. Si5013-EVB
E VALUATION BOARD FOR Si5013 SiPHY MULTI-RATE SONET/SDH CLOCK AND DATA RECOVERY IC Description The Si5013 evaluation board provides a platform for testing and characterizing Silicon Laboratories Si5013
ic-mq EVAL MQ1D EVALUATION BOARD DESCRIPTION
Rev A3, Page 1/7 ORDERING INFORMATION Type Order Designation Description and Options Evaluation Board ic-mq EVAL MQ1D ic-mq Evaluation Board ready to operate, accessible through GUI via PC adapter Software
AN0822: Simplicity Studio User's Guide
Simplicity Studio greatly reduces development time and complexity with Silicon Labs' EFM32, EFM8, and 8051 MCUs, wireless MCUs, and ZigBee SoCs. Simplicity Studio can create wireless applications and provides
SYSTEM 4C. C R H Electronics Design
SYSTEM 4C C R H Electronics Design SYSTEM 4C All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, A outputs. Independent 25
Si52142 PCI-EXPRESS GEN 1, GEN 2, & GEN 3 TWO OUTPUT CLOCK GENERATOR WITH 25 MHZ REFERENCE CLOCK. Features. Applications.
PCI-EXPRESS GEN 1, GEN 2, & GEN 3 TWO OUTPUT CLOCK GENERATOR WITH 25 MHZ REFERENCE CLOCK Features PCI-Express Gen 1, Gen 2, Gen 3, and Gen 4 common clock compliant Gen 3 SRNS Compliant Two 100 MHz, 125
Quad 2-input NAND Schmitt trigger
Rev. 9 15 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Applications The is a quad two-input NAND gate. Each input has a Schmitt trigger circuit. The gate switches
AVR151: Setup and Use of the SPI. Introduction. Features. Atmel AVR 8-bit Microcontroller APPLICATION NOTE
Atmel AVR 8-bit Microcontroller AVR151: Setup and Use of the SPI APPLICATION NOTE Introduction This application note describes how to set up and use the on-chip Serial Peripheral Interface (SPI) of the
SYSTEM 45. C R H Electronics Design
SYSTEM 45 C R H Electronics Design SYSTEM 45 All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, & A outputs. Independent 25
Current Probes. User Manual
Current Probes User Manual ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design, or for any other reason. Nothing contained herein shall
August 2001 PMP Low Power SLVU051
User s Guide August 2001 PMP Low Power SLVU051 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service
In-System Programmer USER MANUAL RN-ISP-UM RN-WIFLYCR-UM-.01. www.rovingnetworks.com 1
RN-WIFLYCR-UM-.01 RN-ISP-UM In-System Programmer 2012 Roving Networks. All rights reserved. Version 1.1 1/19/2012 USER MANUAL www.rovingnetworks.com 1 OVERVIEW You use Roving Networks In-System-Programmer
Data Sheet. Adaptive Design ltd. Arduino Dual L6470 Stepper Motor Shield V1.0. 20 th November 2012. L6470 Stepper Motor Shield
Arduino Dual L6470 Stepper Motor Shield Data Sheet Adaptive Design ltd V1.0 20 th November 2012 Adaptive Design ltd. Page 1 General Description The Arduino stepper motor shield is based on L6470 microstepping