I-STORM LAN ROUTER ADSL

Size: px

Start display at page:

Download "I-STORM LAN ROUTER ADSL"

Aldous Baker
7 years ago
Views:

1 I-STORM LAN ROUTER ADSL with 4 Fast Ethernet ports + 1 USB port Quick Start Guide A02-RA2+/G2 (February 2004)V1.10 1

2 For more detailed instructions on configuring and using the I- Storm Lan Router ADSL, please refer to the online manual. Before beginning the configuration of the Router you have to know the parameters of your subscription ADSL. There are five ways PPPoE, PPPoA, RFC1483 routed, IPoA, RFC1483 Bridge for the device to have a public IP address and then to access Internet. You have to check with your ISP about which way is adopted. VPI/VCI: Consult the telephone company to get the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) numbers. The valid range for the VPI is 0 to 255 and for the VCI is 32 to The default value VPI is 0 and VCI is 32. For BT (VPI=0, VCI=38) and for KC ((VPI=1, VCI=50). NAT: The NAT feature allows multiple-user Internet access for the cost of a single IP account. If you need to have a public server or a public network, NAT has to be disabled. Encapsulation Method: Be sure to use the encapsulation method (LLC/SNAP or VC MUX) required by your ISP. Gather the information as illustrated in the following table and keep it for reference. PPPoE PPPoA VPI and VCI VC-based / LLC-based multiplexing Username and Password Service Name VPI and VCI VC-based / LLC-based multiplexing Username and Password 2

3 RFC1483 Bridged RFC1483 Routed IPoA VPI/VCI VC-based / LLC-based multiplexing VPI/VCI VC-based / LLC-based multiplexing IP address Subnet mask Default Gateway (IP address) IP address (DNS) VPI/VCI IP address Subnet mask Default Gateway (IP address) IP address (DNS) 1.1 Package contents Make sure that you have the following items: I-Storm Lan Router ADSL Network cable (CAT 5) Cable USB Cable RJ-11 ADSL Power Adapter AC-DC (12V, 1A) CD-ROM (with manual, software and driver) This Quick Start Guide 3

4 1.2 Cabling Plug one end of the RJ11 cable into the ADSL port on the rear panel of the Router and insert the other end into splitter, then connect to Rj45 ports by an Ethernet cable your PCs or Switch. Finally connect the Adapter to power inlet and turn the power switch on. Now the I-Storm LAN Router ADSL will enter a selftest phase for about ten seconds. After this phase the SYS led will be flashed to indicate that router is in normal operation. Now you should see the ADSL led first blinking during alignment and then steady when connection is on. 1.3 The Front Panel LEDs Port Information 6 POWER Lit green when power adapter is connected. 7 SYS System status indicators when blinking indicate system is alive. 8 USB Steady green light indicates a valid ADSL connection LAN Blinking green light indicates an active WAN session. 4

5 13 ADSL When lit, it indicates that the ADSL (Line) port is connected to the DSLAM and working properly. 1.4 The Rear Ports 1 2 Port Line(RJ11) USB Meaning Connect the supplied RJ-11 cable to this port when connecting to the ADSL/telephone network. Connect the USB cable to this port when Upgrading Firmware or connecting to PC 3 Reset Press it (10 sec) to restore the factory default setting back 4 5 LAN (4 connettori RJ-45) POWER (jack) Connect a straight or crossover Ethernet cable to this port when connecting to PCs or Switch in the network Connect the supplied power adapter to this jack 6 POWER Switch Premere per accendere/spegnere il Router 5

6 1.5 Default Settings I-Storm LAN Router ADSL Before you configure this I-Storm Lan Router ADSL, you need to know the following default settings. Leaving these settings, configuring the PCs such as DHCP client (follow the instructions below) and configuring ISP connection (You have to check with your ISP about which way is adopted) you can configure the I-Storm Lan Router ADSL quickly. For a more detailed configuration refer to manual on Installation CD. Below the I-Storm Lan Router ADSL default settings: User Name:admin Password:Atlantis IP Address ( ) Subnet Mask ( ) ISP Protocol =PPPoA con VCMux DHCP Server active with IP range from to IE Configuration Now open IE, go to Instruments menu, select the Connections tab and select one of the following options: Never use remote connection Use remote connection if another network connection isn t available Look the following picture. 6

7 7

8 1.7 TCP/IP Configuration Configuring PC (Windows 95/98/ME) 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC. 3. Click Properties. 8

9 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button. 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click OK to finish the configuration. 9

10 10

11 Configuring PC (Windows NT4.0) 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK. 11

12 12

13 Configuring PC (Windows 2000) 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click LAN Area Connection. 3. In the LAN Area Connection Status window, click Properties. 13

14 4. Select Internet Protocol (TCP/IP) and click Properties. 14

15 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 15

16 6. Click OK to finish the configuration. 16

17 Configuring (PC in WindowsXP) 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections. 2. Double-click Local Area Connection. 3. In the LAN Area Connection Status window, click Properties. 17

18 4. Select Internet Protocol (TCP/IP) and click Properties. 18

19 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 19

20 6. Click OK to finish the configuration 1.6 Browser configuration Open the web browser, enter the local port IP address of this I- Storm Lan Router ADSL, which default at , and click Go to get the login page. The default username is admin, password Atlantis and click OK to continue. 20

21 At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including: STATUS (ADSL, LAN, PPP, Learned MAC Table, Routing Table, System Log, Security Log), Quick Start CONFIGURATION (WAN, LAN, System, Firewall, Virtual Server, Advanced) Save Config to Flash. Click on the desired item to expand the page with all settings in the main navigation pane. Following next steps you can make operating I-Storm Lan Router ADSL in short time using DHCP mode on lan PCs. Refer to manual on Installation CD if you need personalized configuration. Selecting Quick Start, on the right of the screen will appear the frame where you can configure your ISP settings. 21

22 PPPoE(RFC 2516)/ PPPoA (RFC 2364) PPPoE (PPP over Ethernet) is known as a dial-up DSL or cable service. Like PPPoA it is designed to integrate the broadband services into the current widely deployed, easy-to-use, and low-cost dial-up-access networking infrastructure. Therefore, users can get greater access speed without changing the operation concept, sharing the same ISP account and paying for one access account. No PPPoE client software is required for local computer if you select this configuration. Look the following settings: Per PVC Setting Virtual Circuit= Enabled Connection Encapsulation= Select PPPoE LLC (or sometimes PPPoE VC-Mux) with PPPoE. With PPPoA select PPPoA VC-Mux (or PPPoA LLC) Bridge=disabled VPI=8 (ISP) VCI=35 (ISP) Static IP Settings Static IP Address= Subnet Mask= Gateway= Account Setup Username provided by ISP: Enter the username provided by your ISP. Maximum input is 63 alphanumeric characters (case sensitive). Password provided by ISP: Enter the password provided by your ISP. Maximum input is 63 alphanumeric characters (case sensitive). 22

23 Click on Submit, Save Config and finally on Submit. RFC1483/RFC1577 How to configure WAN interface with statical IP provided by ISP. Look the following settings: Per PVC Setting Virtual Circuit= Enabled Connection Encapsulatio= 1483 Routed IP LLC or 1483 Routed IP VC-Mux. Chose Classical IP over ATM with RFC1577. Bridge=disabled VPI=8 (ISP) VCI=35 (ISP) Static IP Settings Static IP Address= Insert the statical IP provided by ISP. Subnet Mask= Insert the Subnet Mask provided by ISP. Gateway= Insert the Default Gateway of I-Storm Lan Router ADSL provided by ISP. Account Setup Username: Password: Click on Submit, Save Config and finally on Submit. The ADSL Router will reboot automatically. After reboot all pc of the network will be able to surf the Internet. DHCP server will be provide for each PC an IP address, Subnet Mask, 23

24 Default Gateway and DNS server. By these settings all packets sent to the LAN will be forwarded on the right client the other will be forwarded by the Default Gateway (Atlantis I-Storm LAN Router ADSL) to the Internet. 24

RedRapid X WIRELESS MODEM ROUTER. Quick Installation Guide (DN-7060)

RedRapid X WIRELESS MODEM ROUTER Quick Installation Guide (DN-7060) 1. Product Introduction Congratulations on purchasing this Wireless N ADSL2/2+ Router. This router is a cost-effective ADSL2+ router,