HDMI / DVI to Component CONVERTER P/N: (CV-509) Installation and Setu

Transcription

1 HDMI / DVI to Component CONVERTER P/N: (CV-509) Installation and Setu

2 Safety and Notice The HDMI / DVI to Component Converter [P/N: (CV-509)] has been tested for conformity to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the HDMI / DVI to Component Converter should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. Follow all instructions and warnings marked on this unit. Do not attempt to service this unit yourself, except where explained in this manual. Provide proper ventilation and air circulation and do not use near water. Keep objects that might damage the device and assure that the placement of this unit is on a stable surface. Use only the power adapter and power cords and connection cables designed for this unit. Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning. P/N: Revision 01 October, 2010 Installation and Setu

3 Table of Contents Chapter 1 Introduction 1 Overview 1 Features 1 Package Contents 1 Specifications 2 Chapter 2 Panel Description 3 Chapter 3 Connection Diagram 4 Chapter 4 Hardware Installation 5 Chapter 5 EDID Learning 5 Warranty 5 Rev.0908

4

5 Overview This HDMI / DVI to Component Converter [P/N: (CV-509)] offers an easy and instant approach for converting digital HDMI to analog PC video (VGA) and component video (YPbPr) with digital audio (S/PDIF) and analog stereo audio. With this module, component based display such as monitors, TV or projectors can be readily connected to HDMI sources. In addition, the embedded HDMI / DVI selector facilitates the switch between the HDMI and DVI input sources. This solution lets you keep using your non-hdmi/dvi display to access HDMI or DVI source, and enjoy high definition digital video and audio. Features HDMI 1.2a & DVI 1.1 compliant HDMI video supports up to 1080p Support HD (1080i / 720p) component video output Support up to UXGA (1600x1200@60) & WUXGA (1920x1200@60) PC graphics output Coaxial S/PDIF audio output Stereo analog audio output Front panel LED indicators and push button EDID learning ability Introduction Package Contents Part Number Description Quantity P/N: HDMI / DVI to component converter (CV-509) 1 P/N: ft RCA male-male component video cable (RGB) 1 P/N: VGA-component breakout cable 1 P/N: Installation and Setup Guide 1 P/N: V 4A in-line power supply unit with power cord 1 1

6 Specifications Technical Role of usage HDMI / DVI to component converter [P/N: (CV-509)] D/A converter HDMI compliance HDMI 1.2a DVI compliance DVI 1.1 Video bandwidth Video support Audio support Input TMDS signal Input DDC signal Input Output HDMI connector DVI connector VGA connector RCA connector 3.5mm connector Single-link 165MHz [4.95Gbps] Up to 1080p60, WUXGA [1920x1200@60] & UXGA [1600x1200@60] Stereo audio 1.2 Volts [peak-to-peak] 5 Volts [peak-to-peak, TTL] 1x HDMI 1x DVI 1x VGA or Component (via VGA-component breakout cable) 1x RCA digital audio 1x 3.5mm analog audio Type A [19-pin female] DVI-I [29-pin female digital only] HD-15 [15-pin D-sub female] Coaxial socket for S/PDIF digital stereo audio [PCM 48kHz] Earphone socket for analog stereo audio Push-in button [1] HDMI / DVI input switch [2] VGA / component output switch DIP switch Housing Mechanical Dimensions (L x W x H) Weight Fixedness Power supply 2-pin for EDID learning HDMI / DVI to component converter [P/N: (CV-509)] Metal enclosure Model 128 x 100 x 28mm [5 x 3.9 x 1.1 ] Package 270 x 175 x 80mm [10.6 x 6.9 x 3.1 ] Model Package Power consumption Operation temperature Storage temperature Relative humidity 420g [15oz] 795g [1.8 lbs] Wall-mounting case 5V 4A DC 6 Watts [max] 0~40 C [32~104 F] -20~60 C [-4~140 F] 20~90% RH [no condensation] 2

7 PaNEL DeSCRIPTION Front Panel DIP Switch for EDID 4. DVI input 2. HDMI or DVI source switch button 5. Power on/off indicator 3. HDMI input 6. +5V DC interlocked power jack DIP Switch Pin 1 ON OFF Pin 2 ON OFF Rear Panel Mode Learn EDID from VGA socket and save EDID to HDMI socket Write back the default EDID to HDMI socket Mode Learn EDID from VGA socket and save EDID to DVI socket Write back the default EDID to DVI socket S/PDIF audio output 8. Stereo audio output 9. Component video output via the breakout cable (P/N: ) 10. VGA or component output switch button 3

8 Connection Diagram 4

9 Hardware Installation 1. Connect the HDMI or DVI source either to the dual-view video processor [P/N: (MX-1003BB)] or the HDMI CAT5e extender [P/N: (CV-57BB)] to the video input. 2. Connect the S/PDIF or stereo audio source to RCA jack or 3.5mm jack. 3. For connecting to component (YPbPr) TV or projector, link VGA-component breakout cable (P/N: ) to the VGA output connector then link a component cable (P/N: ) to the component (YPbPr) TV or projector. 4. Power up the HDMI / DVI to component converter [P/N: (CV-509)] with the 5V 4A DC power supply unit (P/N: ) connected. EDID Learning 1. Power up the converter [P/N: (CV-509)]. Connect display to VGA/YPbPr Output. 2. To learn EDID for HDMI source i.e., the HDMI CAT5e extender [P/N: (CV-57BB)], pull down the DIP switch 1 to ON, the red LED will flash to indicate the EDID learning process is complete. You DON T NEED to pull up the DIP switch again unless you want to learn another EDID by pulling DIP switch 1 up and down. 3. To learn EDID for DVI source i.e., the dual-view video processor [P/N: (MX-1003BB)], pull down the DIP switch 2 to ON, the red LED will flash to indicate the EDID learning process is complete. You DON T NEED to pull up the DIP switch again unless you want to learn another EDID by pulling DIP switch 1 up and down. Warranty Please refer to Barfly Installation and Setup Guide (P/N: ) and BARFLY SERVICE SUPPLEMENT for warranty information. 5