10.1 MUELLER 2360 SERIES RESILIENT WEDGE GATE VALVE
|
|
- Marianna Evans
- 7 years ago
- Views:
Transcription
1 MUELLER 2360 SERIES RESILIENT WEDGE GATE VALVE 10.1 MUELLER 2300 Series Resilient Wedge Gate Valves Mueller Resilient Wedge Gate Valves have features to make them easier to operate and to preserve the sealing capability and interior coating integrity for many years of reliable service. In addition to popular end connection options, Mueller brand RW valves can be ordered with Mueller s exclusive Aqua-Grip System that incorporates an O-ring sealed compression connection and integral pipe restraint in one ready to use easy and quick to install package. TRIPLE O-RING SEALS PLUS DIRT SEAL two above thrust collar and one below, retain lubricant in this critical area. Top two are replaceable with valve fully open and under pressure. Fourth seal at top serves as dirt seal. TWO ANTI-FRICTION WASHERS WITH LUBRICATION made of polymer, one above and one below the thrust collar, reduce operating torque to open or close valve. STEM forged manganese bronze bar stock is upset, then machined to form a thrust collar for superior strength in this critical area. WEDGE cast iron, fully encapsulated in molded rubber - no exposed iron. EXTENDED WEDGE GUIDES molded as part of wedge, ride inside body channels to maintain wedge alignment throughout its travel. GUIDE CAP BEARINGS made of polymer and snapped over rubber covered wedge guides, provide bearing surfaces that protect both wedge and interior body coating from wear and aid in easy operation even the largest valves installed horizontally. Rollers, tracks or scrapers are not needed. Mueller 2" 12" 2360 Series Resilient Wedge Gate Valve Features SMOOTH, OVERSIZED FLOW WAY full, round, unobstructed flow way accommodates full size cutters, provides superior flow characteristics and reduces pumping costs.** MUELLER PRO-GARD FUSION EPOXY COATING 10 mils* thick protects all inside and outside iron surfaces, and complies with AWWA C550 and certified to ANSI/NSF PSIG MAXIMUM WORKING PRESSURE Hydrostatically tested at 500 psig. Surpasses ANSI/AWWA Standard C509 by 25%. UL/FM: 200 psig MWP.*** AMERICAN MADE QUALITY factory in Chattanooga, TN with ISO 9001:2000 certification, and UL 262, FM 1120/1130. Certified to ANSI/NSF 61. Manufactured and tested in compliance with ANSI/AWWA Standard C509. UL Listed and FM Approved. BI-DIRECTIONAL FLOW FLAT BOTTOM SURFACES stands upright for easier handling and storage. 10-YEAR LIMITED WARRANTY assured reliability (see separate Mueller Warranty document for terms). Mueller 14" 48" 2361 Series Resilient Wedge Gate Valve Features In addition to all the features of the smaller 2360 series valves, large size Mueller 2361 series RW valves offer these features: STEM Manganese bronze casting with integral thrust collar. COMPLIANCE In addition to those above: ANSI/AWWA Standard C515. WEDGE Ductile iron, fully encapsulated in molded rubber. BODY AND BONNET Ductile iron. MAXIMUM WORKING PRESSURE 14"-48" AWWA valves rated at 250 psig tested at 500 psig. UL/FM valves 200 psig MWP (14"-16" 250 psig MWP).*** *Nominal **16" valve requires 1/2" undersized cutter. ***250 psi UL/FM rating available as an option. Dirt seal on 4"-12" valves. Double-Disc Style gate valves follow the RW valve pages.
2 SERIES RESILIENT WEDGE VALVES WITH MUELLER AQUA-GRIP SYSTEM MUELLER 2361 SERIES RESILIENT WEDGE GATE VALVES WITH AQUA-GRIP SYSTEM The Mueller Aqua-Grip System is offered in 4" through 12" sizes of the Mueller 2361 Series Resilient Wedge Gate Valves. This Mueller exclusive combines both the compression connection and the pipe restraint system in one convenient, quick installation package. This eliminates the need for anchor couplings, tie rods or separate gland-type restrains. A typical Aqua-Grip connection uses fewer bolts than a conventional mechanical joint end, and substantially fewer than a gland-type restraint, significantly reducing installation time. This labor saving system is also available on Mueller Centurion Fire Hydrants, and as separate couplings and fittings to compliment water main installation needs. ACCEPTS VARIED TYPES OF PIPE DIPS style fits DI, C900 PVC and DIPS PE pipe. IPS style fits PVC, IPS PE and steel pipe. No disassembly or adapters, no special pipe end preparation, and no liner for PE pipe (DR9-DR17) required. FULLY ASSEMBLED STAB CONNECTION arrives ready to insert the pipe, tighten the bolts and it s done. No need to change-out, add or remove parts. Nothing additional to inventory or handle in the field. No extra bolts to assemble or tighten. Substantially reduces labor and inventory costs. VISUALLY SHOWS WHEN PROPERLY TIGHTENED breakaway nuts snap off using a standard wrench. No special torque requirements. Inner nut remains in place to allow future access to connection, if required. Reduces crew training and saves installation time. (In illustration, lower nut shown before tightening, upper one after.) PRESSURE RESPONSIVE O-RING SEAL a double O-ring uses hydrostatic pressure from inside the pipe to enhance the seal as line pressure increases. FULL CIRCUMFERENTIAL RESTRAINT gripper ring encircles pipe for uniform grip without creating points of high stress in pipe wall that could contribute to pipe failure. INSTALLS IN WET CONDITIONS no special field conditions required, even installs under water. DUCTILE IRON CONSTRUCTION valve body, bonnet and the Aqua-Grip System components. PLUS ALL THE OTHER FEATURES OF THE 2300 SERIES VALVES
3 10.3
4 10. Shaded area indicates change. 4"-12" A-2361 RESILIENT WEDGE GATE VALVE WITH AQUA-GRIP x FL. ENDS Catalog number A Aqua-Grip ends x flanged ends for DIPS pipe in sizes 4", 6", 8", 10", 12" A Aqua-Grip ends x flanged ends for IPS pipe in sizes 4", 6", 8" Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Flanged end dimensions and drilling comply with ANSI B16.1, class 125 Ductile Iron body and bonnet with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving as dirt seal 2" square wrench nut or handwheel available open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure UL Listed, FM Approved 200 psig (1379 kpa) A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Resilient wedge gate valve parts Catalog Part No. Handwheel Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box O-ring Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box with dirt seal Cast iron Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Cast Iron* Rubber Encapsulation SBR ASTM A126 CL.B -- ASTM A126 CL.B -- G-210 Bonnet Ductile Iron ASTM A536 Grade G-211 Bonnet O-ring Rubber G-212 Body Ductile Iron G-213 Double O-ring** Rubber G-214 Intermediate ring** Ductile Iron G-215 Gripper ring** Ductile Iron G-216 End ring** Ductile Iron G-217 Breakaway nut w/washer*** Steel G-218 T-head Bolt*** Steel ASTM A536 Grade ASTM A536 Grade ASTM A536 Grade ASTM A536 Grade G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210 G-16 G-211 G-205 G-212 G-209 G-206 *Fully encapsulated in molded rubber with no iron exposed. **Parts for Aqua-Grip connection not shown one required for each Aqua-Grip connection. ***Not shown. See dimension drawing on next page for number require for each size Aqua-Grip connection. SEE PAGE FOR ORDERING INSTRUCTIONS
5 A 4"-12" A-2361 RESILIENT WEDGE GATE VALVE WITH AQUA-GRIP x FL. ENDS 10. G B Q UUR KK F T Dimensions Dimension* Nominal size 4" 6" 8" 10" 12" A B (number and size of holes for FL) F G (number and size of holes for Aqua-Grip) T R Q (Bore) FF KK UU (bolt circle diameter for FL) Turns to open Weight* *All dimensions are in inches. All weights are in approximate pounds. FF
6 10.6 Shaded area indicates change. 4"-12" A-2361 RESILIENT WEDGE GATE VALVE WITH AQUA-GRIP x AQUA-GRIP ENDS Catalog number A Aqua-Grip ends x Aqua-Grip ends for DIPS pipe in sizes 4", 6", 8", 10", 12" A Aqua-Grip ends x Aqua-Grip ends for IPS pipe in sizes 4", 6", 8" Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Ductile Iron body and bonnet with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving as dirt seal 2" square wrench nut (optional handwheel available) -open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure UL Listed, FM Approved 200 psig (1379 kpa) A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box O-ring Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box with dirt seal Cast iron Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Cast Iron* Rubber Encapsulation SBR ASTM A126 CL.B -- ASTM A126 CL.B -- G-210 Bonnet Ductile Iron ASTM A536 Grade G-211 Bonnet O-ring Rubber G-212 Body Ductile Iron G-213 Double O-ring** Rubber G-214 Intermediate ring** Ductile Iron G-215 Gripper ring** Ductile Iron G-216 End ring** Ductile Iron G-217 Breakaway nut w/washer*** Steel G-218 T-head Bolt*** Steel ASTM A536 Grade ASTM A536 Grade ASTM A536 Grade ASTM A536 Grade G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210 G-16 G-211 G-205 G-212 G-209 G-206 *Fully encapsulated in molded rubber with no iron exposed. **Parts for Aqua-Grip connection not shown one required for each Aqua-Grip connection. ***Not shown. See dimension drawing on next page for number require for each size Aqua-Grip connection. SEE PAGE FOR ORDERING INSTRUCTIONS
7 4"-12" A-2361 RESILIENT WEDGE GATE VALVE WITH AQUA-GRIP x AQUA-GRIP ENDS 10. A G F KK FF Dimensions Dimension* Nominal size 4" 6" 8" A FF G (number and size of holes for Aqua-Grip) F KK Turns to open Weight* *All dimensions are in inches. All weights are in approximate pounds. 10" "
8 10. Shaded area indicates change. 4"-12" A-2361 RESILIENT WEDGE GATE VALVE WITH AQUA-GRIP x MJ. ENDS Catalog number A Aqua-Grip ends x mechanical joint for DIPS pipe in sizes 4", 6", 8", 10", 12" A Aqua-Grip ends x mechanical joint for IPS pipe in sizes 4", 6", 8" Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Ductile Iron body and bonnet with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy Coated interior and exterior surfaces. Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61. Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron. Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving as dirt seal 2" square wrench nut (optional handwheel available) open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure UL Listed, FM Approved 200 psig (1379 kpa) A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box O-ring Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box with dirt seal Cast iron Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Cast Iron* Rubber Encapsulation SBR ASTM A126 CL.B -- ASTM A126 CL.B -- G-210 Bonnet Ductile Iron ASTM A536 Grade G-211 Bonnet O-ring Rubber G-212 Body Ductile Iron G-213 Double O-ring** Rubber G-214 Intermediate ring** Ductile Iron G-215 Gripper ring** Ductile Iron G-216 End ring** Ductile Iron G-217 Breakaway nut w/washer*** Steel G-218 T-head Bolt*** Steel ASTM A536 Grade ASTM A536 Grade ASTM A536 Grade ASTM A536 Grade G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210 G-16 G-211 G-205 G-212 G-209 G-206 *Fully encapsulated in molded rubber with no iron exposed. **Parts for Aqua-Grip connection not shown one required for each Aqua-Grip connection. ***Not shown. See dimension drawing on next page for number require for each size Aqua-Grip connection. SEE PAGE FOR ORDERING INSTRUCTIONS
9 4"-12" A-2361 RESILIENT WEDGE GATE VALVE WITH AQUA-GRIP x MJ. ENDS 10. A O G N Q M OO KK F L FF Dimensions Dimension* Nominal size 4" 6" A F G (number and size of holes for Aqua-Grip) L M N O (number and size of holes for MJ) FF Q KK OO (bolt circle diameter for MJ) Turns to open Weight* " " " *All dimensions are in inches. All weights are in approximate pounds.
10 10.10 Shaded area indicates change. 2"-12" A-2360 RESILIENT WEDGE Gate Valve - FL. x FL. Catalog number A flanged ends Sizes 2", 2-1/2", 3", 4", 6", 8", 10", 12" Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Flanged end dimensions and drilling comply with ANSI B16.1, class 125 Iron body with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving as dirt seal Handwheel (2" square wrench nut optional) open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure 2-1/2"-12" sizes UL Listed, FM Approved: 200 psig (1379 kpa) Approved for backflow prevention devices by USC (for 2-1/2" - 10" sizes) Dirt seal on 4"-12" valves A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 PN 10/16 Drilling ASTM B98-C66100/H02 stem 2" square wrench nut Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box with dirt seal * Fully encapsulated in molded rubber with no iron exposed ** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with additional bolts (2"-3" sizes retain neoprene gasket design affecting these parts). Confirm the type of seal when ordering a replacement gasket or O-ring. Dirt seal on 4"-12" valves Cast iron Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Rubber Encapsulation Cast Iron* SBR ASTM A126 CL.B ASTM A126 CL.B -- G-210** Bonnet Cast Iron ASTM A126 CL.B G-211** Bonnet O-ring Nitrite G-212** Body Cast Iron ASTM A126 CL.B SEE PAGE FOR ORDERING INSTRUCTIONS
11 2"-12" A-2360 RESILIENT WEDGE GATE VALVE - FL. x FL E B A R Q UU FF Dimensions Dimension* Nominal size 2" 2-1/2" 3" 4" 6" 8" 10" 12" A E R FF Q (bore) UU (bolt circle diameter) B (number and size of holes) Turns to open Weight* *All dimensions are in inches. All weights are in pounds and are approximate.
12 10.12 Shaded area indicates change. 4"-12" A-2360 RESILIENT WEDGE Gate Valves - M.J. x FL. Catalog number A mechanical joint x flanged ends (with accessories unassembled) A mechanical joint x flanged ends (less accessories) Sizes 4", 6", 8", 10", 12" Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Flanged end dimensions and drilling comply with ANSI B16.1, class 125 Mechanical joint end complies with ANSI/AWWA C111 Standard Iron body with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper &1 lower O-rings), with fourth O-ring serving as dirt seal 2" square wrench nut (optional handwheel available) open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure UL Listed, FM Approved 200 psig (1379 kpa) A M.J. accessories shipped unassembled Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box with dirt seal Cast iron Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Rubber Encapsulation Cast Iron* SBR * Fully encapsulated in molded rubber with no iron exposed ASTM A126 CL.B ASTM A126 CL.B -- G-210** Bonnet Cast Iron ASTM A126 CL.B G-211** Bonnet O-ring Nitrite G-212** Body Cast Iron ASTM A126 CL.B ** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with additional bolts. Confirm the type of seal when ordering a replacement gasket or O-ring. G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210** G-16 G-211** G-205 G-212** G-209 G-206 SEE PAGE FOR ORDERING INSTRUCTIONS
13 4"-12" A-2360 RESILIENT WEDGE Gate valve - m.j. x fl Dimensions Dimension* Nominal size 4" 6" 8" 10" 12" A L N O (number and size of holes for MJ) Q (bore) OO (bolt circle diameter for MJ) R UU (bolt circle diameter for FL) FF B (number and size of holes for FL) Turns to open Weight* * All dimensions are in inches. All weights include accessories are in pounds and are approximate.
14 10.14 Shaded area indicates change. 2"-12" A-2360 RESILIENT WEDGE gate valves - m.j. x M.j. Catalog number A Mechanical joint ends (with accessories unassembled) A Mechanical joint ends (less accessories) A Mechanical joint ends (with transition gaskets accessories unassembled) Sizes 2", 3", 4", 6", 8", 10", 12" Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Standard mechanical joint ends comply with ANSI/AWWA C111 Iron body with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving as dirt seal 2" square wrench nut (optional handwheel available) -open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure 3"-12" sizes UL Listed, FM Approved: 200 psig (1379 kpa) Dirt seal on 4"-12" valves A M.J. accessories shipped unassembled Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box with dirt seal Cast iron Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Rubber Encapsulation Cast Iron* SBR ASTM A126 CL.B -- ASTM A126 CL.B -- G-210** Bonnet Cast Iron ASTM A126 CL.B G-211** Bonnet O-ring Nitrile G-212** Body Cast Iron ASTM A126 CL.B * Fully encapsulated in molded rubber with no iron exposed ** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with additional bolt holes (2"-3" sizes retain neoprene gasket design affecting these parts). Confirm the type of seal when ordering a replacement gasket or O-ring. Dirt seal on 4"-12" valves SEE PAGE FOR ORDERING INSTRUCTIONS G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210** G-16 G-211** G-205 G-212** G-209 G-206
15 2"-12" A-2360 RESILIENT WEDGE gate valve - m.j. x m.j Dimensions Dimension* Nominal size 2" 3" 4" 6" 8" 10" 12" A FF L N O (number and size of holes) DD Q (bore) OO (bolt circle diameter) Turns to open Weight* *All dimensions are in inches. All weights include accessories are in pounds and are approximate.
16 10.16 Shaded area indicates change. 4"-12" A-2360 RESILIENT WEDGE gate valves - sl. x sl. Catalog number A Slip-on ends with gasket A Slip-on ends less gasket Sizes 4", 6", 8", 10", 12" Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Slip-on ends fit plain end of classes 150, 200 and 250 cast iron; ductile iron and classes 150 and 200 cast iron O.D. PVC Iron body with nominal 10 mils MUELLER Pro-Gard TM Fusion Epoxy Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-ring), with fourth O-ring serving as dirt seal 2" square wrench nut (optional handwheel available) open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure UL Listed, FM Approved: 200 psig (1379 kpa) Design and dimensions of the joint are manufactured under license of U.S. Pipe and Foundry Company. A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box with dirt seal Cast iron Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Rubber Encapsulated Stainless Steel Type 304 Cast Iron* SBR ASTM A126 CL.B -- ASTM A126CL.B -- G-210** Bonnet Cast Iron ASTM A126 CL.B G-211** Bonnet O-ring Nitrile G-212** Body Cast Iron ASTM A126 CL.B * Fully encapsulated in molded rubber with no iron exposed ** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with additional bolts. Confirm the type of seal when ordering a replacement gasket or O-ring. SEE PAGE FOR ORDERING INSTRUCTIONS G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210** G-16 G-211** G-205 G-212** G-209 G-206
17 4"-12" A-2360 RESILIENT WEDGE gate valve - sl. x sl A Q W L DD FF Dimensions Dimension* *All dimensions are in inches. All weights are in pounds and are approximate. Nominal size 4" 6" 8" 10" 12" A Q (bore) W (distance between strapping lug holes across face of valve ends) FF L DD Turns to open Weight*
18 10.18 Shaded area indicates change. 4"-12" A-2360 RESILIENT WEDGE GATE VALVES - SL. x FL. Catalog number A Slip-on end (with gasket) x flange end A Slip-on end (less gasket) x flange end Sizes 4", 6", 8", 10", 12" Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Slip-on ends fit plain end of classes 150, 200 and 250 cast iron, ductile iron and classes 150 and 200 cast iron O.D. PVC Flange end dimensions and drilling comply with ANSI B16.1, class 125 Iron body with nominal 10 mils MUELLER Pro-Gard Epoxy Fusion Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving as dirt seal 2" square wrench nut (optional handwheel available) open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure UL Listed, FM Approved: 200 psig (1379 kpa) Design and dimensions of the joint are manufactured under license of U.S. Pipe and Foundry Company. A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box with Cast iron dirt seal Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Rubber Encapsulation Cast Iron* SBR ASTM A126 CL.B -- ASTM A126 CL.B -- G-210** Bonnet Cast Iron ASTM A126 CL.B G-211** Bonnet O-ring Nitrile G-212** Body Cast Iron ASTM A126 CL.B * Fully encapsulated in molded rubber with no iron exposed ** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with additional bolts. Confirm the type of seal when ordering a replacement gasket or O-ring. SEE PAGE FOR ORDERING INSTRUCTIONS G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210** G-16 G-211** G-205 G-212** G-209 G-206
19 4"-12" A-2360 RESILIENT WEDGE GATE VALVE - SL. x FL B A Q UU R W L FF Dimensions Dimension* *All dimensions are in inches. All weights are in pounds and are approximate. Nominal size 4" 6" 8" 10" 12" A Q (bore) L R UU (bolt circle diameter for FL) B (number and size of holes for FL) W (distance between strapping lug holes across face of valve ends) FF Turns to open Weight*
20 10.20 Shaded area indicates change. 2"-8" A-2360 RESILIENT WEDGE Gate Valves - RAD. x RAD Catalog number A radial compression ends Sizes 2", 2-1/2", 3", 4", 6", 8" Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Radial compression ends fit IPS PVC plastic pipe Iron body with nominal 10 mils MUELLER Pro-Gard Epoxy Fusion Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements o ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving as dirt seal 2" square wrench nut (optional handwheel available) open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure 2 1/2" - 8" sizes UL Listed, FM Approved: 200 psig (1379 kpa) Dirt seal on 4"-8" valves A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing dirt seal Box Cast iron Rubber G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Rubber Encapsulation Cast Iron* SBR ASTM A126 CL.B -- ASTM A126 CL.B -- G-210** Bonnet Cast Iron ASTM A126 CL.B G-211** Bonnet O-ring Nitrile G-212** Body Cast Iron ASTM A126 CL.B * Fully encapsulated in molded rubber with no iron exposed ** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with additional bolts (2"-3" sizes retain neoprene gasket design affecting these parts). Confirm the type of seal when ordering a replacement gasket or O-ring. Dirt seal on 4"-8" valves G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210** G-16 G-211** G-205 G-212** G-209 G-206 SEE PAGE FOR ORDERING INSTRUCTIONS
21 2"-8" A-2360 RESILIENT WEDGE GATE VALVE - RAD. x RAD Dimensions Dimension* Nominal size 2" 2-1/2" 3" 4" 6" 8" A FF L Q (bore) DD Turns to open Weight* *All dimensions are in inches. All weights are in pounds and are approximate.
22 10.22 Shaded area indicates change. 2", 2-1/2" & 3" A-2360 RESILIENT Wedge Gate valve -THD. x Thd. Catalog number A threaded ends Sizes 2", 2-1/2", 3" Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Threaded end dimensions comply with ANSI B2.1 Iron body with nominal 10 mils MUELLER Pro-Gard Epoxy Fusion Coated interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-rings) 2" square wrench nut (optional handwheel available) open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure 3" size UL Listed, FM Approved: 200 psig (1379 kpa) A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 316 ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-41 Stuffing Box Bolts & Nuts Stainless Steel Type 304 G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Stainless Steel Type 304 G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box Cast iron ASTM A126 CL.B G-208 Anti-friction Washers (2) Celcon G-209 Wedge, Cast Iron* ASTM A126 CL.B Rubber Encapsulation SBR -- G-210 Bonnet Cast Iron ASTM A126 CL.B G-211 Bonnet Gasket Neoprene G-212 Body Cast Iron ASTM A126 CL.B G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210 G-16 G-211 G-205 G-212 G-209 G-206 * Fully encapsulated in molded rubber with no iron exposed SEE PAGE FOR ORDERING INSTRUCTIONS
23 2", 2-1/2" & 3" A-2360 RESILIENT wedge gate valve - thd. x thd Dimensions Dimension* *All dimensions are in inches. All weights are in pounds and are approximate. Nominal size 2" 2-1/2" 3" A FF Q (bore) H (hex across flats) DD Turns to open Weight*
24 10.24 Shaded area indicates change. 14"-48" A-2361 D.I. RESILIENT WEDGE Gate Valve - FL. x Fl. Catalog number A flanged ends Sizes 14", 16", 18", 20", 24", 30", 36", 42", 48" Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Flanged end dimensions and drilling comply with ANSI B16.1, class 125 Ductile iron body and bonnet with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy coating interior and exterior surfaces; 42" and 48" valves coated with Tnemec liquid epoxy. Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61. Ductile iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron. Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-ring) 2" square wrench nut (optional bevel or spur gearing) open left or open right 30" - 48" require a Spur Gear or Bevel Gear 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure 14" and 16" sizes UL Listed, FM Approved: 250 psig (1723 kpa) A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 304, Type 316 Handwheel ASTM B98-C66100/H02 stem: 14"-16" Bypass 18"- 48" (2" on 18"-20"; 2.5" on 24"; Spur or bevel geared actuator ASTM B763-C99500: 18"- 48" 3" on 30"- 48") Resilient wedge gate valve parts Catalog Description Part Material Material standard No. G-16 Bonnet Bolts & Nuts Carbon Steel ASTM A307 Grade B, Zinc Plated G-41 Stuffing Box Bolts & Nuts Carbon Steel ASTM A307 Grade B, Zinc Plated G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Carbon Steel ASTM A307 Grade B, Zinc Plated G-201 Stuffing Box O-Ring Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138** G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box Ductile Iron ASTM A536 G-208 Anti-friction Washers (2) Brass G-209 Wedge, Rubber Encapsulation Ductile Iron* SBR ASTM A G-210 Bonnet Ductile Iron ASTM A536 G-211 Bonnet O-ring Rubber G-212 Body Ductile Iron ASTM A536 * Fully encapsulated in molded rubber with no iron exposed **18"- 48" ASTM B584 42" and 48" EPDM standard SEE PAGE FOR ORDERING INSTRUCTIONS G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210 G-16 G-211 G-205 G-212 G-209 G-206
25 14"-48" A-2361 D.I. RESILIENT WEDGE Gate Valve - FL. x Fl Shaded area indicates change. Dimensions Dimension* 14" A R FF Q (bore) UU (bolt circle diameter) B (number and size of holes) A - Spur Gear A - Bevel Gear** Turns to open (without gearing) 43.5 Turns to open (Spur gearing) 178 Nominal size 16" " " " " " " See A for Spur or Bevel Gear " Turns to open (Bevel gearing) Weight* *All dimensions are in inches. All weights are in pounds and are approximate. Weights for 30"-48" valves are with gearing; for all others without gearing. **Center line of operating nut to center line of valve. Spur or Bevel Gear must be used with 30", 36", 42", 48" valves. Turns shown for Master Gear bevel gearing. Valves with Limitorque bevel gearing: 18" - 227, 20" - 251, 24" - 300".
26 10.26 Shaded area indicates change. Catalog number A mechanical joint x flanged ends (with accessories unassembled) A mechanical joint x flanged ends (less accessories) Sizes 14", 16", 18", 20", 24", 30", 36", 42", 48" Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Flanged end dimensions and drilling comply with ANSI B16.1, class 125 Mechanical joint end complies with ANSI/AWWA C111 Standard Ductile iron body and bonnet with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy coated interior and exterior surfaces; 42" and 48" valves coated with Tnemec liquid epoxy. Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61. Ductile iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron. Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-ring) 2" square wrench nut (optional bevel or spur gearing) open left or open right 30" - 48" require a Spur Gear or Bevel Gear 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure 14" and 16" sizes UL Listed, FM Approved: 250 psig (1723 kpa) 14"-48" A-2361 D.I. RESILIENT WEDGE GATE VALVE - M.J. x F.L. A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 304, Type 316 Handwheel ASTM B98-C66100/H02 stem: 14"-16" Bypass 18" - 48" (2" on 18"-20"; 2.5" on 24"; Spur or bevel geared actuator ASTM B763-C99500: 18"- 48" 3" on 30"- 48") Resilient wedge gate valve parts Catalog Description Part Material Material standard No. G-16 Bonnet Bolts & Nuts Carbon Steel ASTM A307 Grade B, Zinc Plated G-41 Stuffing Box Bolts & Nuts Carbon Steel ASTM A307 Grade B, Zinc Plated G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Carbon Steel ASTM A307 Grade B, Zinc Plated G-201 Stuffing Box O-Ring Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138** G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box Ductile Iron ASTM A536 G-208 Anti-friction Washers (2) Brass G-209 Wedge, Rubber Encapsulated Ductile Iron* SBR ASTM A G-210 Bonnet Ductile Iron ASTM A536 G-211 Bonnet O-ring Rubber G-212 Body Ductile Iron ASTM A536 * Fully encapsulated in molded rubber with no iron exposed **18" - 48" ASTM B584 42" and 48" EPDM standard SEE PAGE FOR ORDERING INSTRUCTIONS G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210 G-16 G-211 G-205 G-212 G-209 G-206
27 14"-48" A-2361 D.I. RESILIENT WEDGE GATE VALVE - M.J. x F.L Shaded area indicates change. *All dimensions are in inches. All weights are in pounds and are approximate. Weights for 30"-48" valves are with gearing; for all others without gearing. **Center line of operating nut to center line of valve. Spur or Bevel Gear must be used with 30", 36", 42", 48" valves. Turns shown for Master Gear bevel gearing. Valves with Limitorque bevel gearing: 18" - 227, 20" - 251, 24" - 300".
28 10.28 Shaded area indicates change. Catalog number A Mechanical joint ends (with accessories unassembled) A Mechanical joint ends (less accessories) Sizes 14", 16", 18", 20", 24", 30", 36", 42", 48" 14"-48" A-2361 d.i. RESILIENT WEDGE Gate valve - m.j. x m.j. ends Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Mechanical joint end complies with ANSI/AWWA C111 Standard. Ductile Iron body and bonnet with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy coated interior and exterior surfaces; 42" and 48 valves coated with Tnemec liquid epoxy. Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61. Ductile Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron. Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-ring). 2" square wrench nut (optional bevel or spur gearing) open left or open right. 30", 36", 42", 48" require a Spur Gear or Bevel Gear 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure 14" and 16" sizes UL Listed, FM Approved: 250 psig (1723 kpa) A Options See page for more information on Resilient Wedge Gate Valve options Position indicators Stainless steel fasteners: Type 304, Type 316 Handwheel ASTM B98-C66100/H02 stem: 14"-16" Bypass 18"- 48" (2" on 18"-20"; 2.5" on 24" Spur or bevel geared actuator ASTM B763-C99500: 18"- 48" 3" on 30"- 48") Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Carbon Steel ASTM A307 Grade B, Zinc Plated G-41 Stuffing Box Bolts & Nuts Carbon Steel ASTM A307 Grade B, Zinc Plated G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Carbon Steel ASTM A307 Grade B, Zinc Plated G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138** G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box Ductile Iron ASTM A536 G-208 Anti-friction Washers (2) Brass G-209 Wedge, Rubber Encapsulation Ductile Iron* SBR ASTM A G-210 Bonnet Ductile Iron ASTM A536 G-211 Bonnet O-ring Rubber G-212 Body Ductile Iron ASTM A536 * Fully encapsulated in molded rubber with no iron exposed ** 18" - 48" ASTM B584 42" and 48" EPDM standard SEE PAGE FOR ORDERING INSTRUCTIONS G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210 G-16 G-211 G-205 G-212 G-209 G-206
29 14"-48" A-2361 D.I. RESILIENT WEDGE GATE Valve - M.J. x M.J Shaded area indicates change. Dimensions Dimension* Nominal size 14" 16" 18" 20" 24" 30" 36" 42" 48" A See A for Spur or Bevel Gear FF L N O (number and size of holes) Q (bore) OO (bolt circle diameter) A - Spur Gear A - Bevel Gear** Turns to open (without gearing) Turns to open (Spur gearing) Turns to open (Bevel gearing) Weight* *All dimensions are in inches. All weights are in pounds and are approximate. Weights for 30"-48" valves are with gearing; for all others without gearing. **Center line of operating nut to center line of valve. Spur or Bevel Gear must be used with 30", 36", 42", 48" valves. Turns shown for Master Gear bevel gearing. Valves with Limitorque bevel gearing: 18" - 227, 20" - 251, 24" - 300".
30 10.30 Shaded area indicates change. 14", 16" A-2361 D.I. RESILIENT WEDGE Gate Valve - SL. x Sl. Catalog number - A Slip-on ends with gasket A Slip-on ends less gasket Sizes 14", 16" Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed, FM Approved, and certified to ANSI/NSF 61. Slip-on ends fit plain end of classes 50 and 100 cast iron; ductile iron and AWWA C905 cast iron O.D. PVC Ductile iron body with nominal 10 mils MUELLER Pro-Gard Fusion Epoxy Coating interior and exterior surfaces Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61 Ductile iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron Non-rising stem (NRS) Triple O-ring seal stuffing box (2 upper & 1 lower O-ring) 2" square wrench nut (optional bevel or spur gearing) open left or open right 250 psig (1723 kpa) maximum working pressure, 500 psig (3447 kpa) static test pressure UL Listed, FM Approved 250 psig (1723 kpa) Design and dimensions of the joint are manufactured under license of U.S. Pipe and Foundry Company. Options See page for more information on Resilient Wedge Gate Valve options A Position indicators Stainless steel fasteners: Type 304, Type 316 Spur or bevel geared actuator ASTM B98-C66100/H02 stem Handwheel Resilient wedge gate valve parts Catalog Part No. Description Material Material standard G-16 Bonnet Bolts & Nuts Carbon Steel ASTM A307 Grade B, Zinc Plated G-41 Stuffing Box Bolts & Nuts Carbon Steel ASTM A307 Grade B, Zinc Plated G-49 Stem O-rings (3) Rubber G-200 Wrench Nut Cap Screw Carbon Steel ASTM A307 Grade B, Zinc Plated G-201 Stuffing Box Seal Rubber G-202 Wrench Nut Cast Iron ASTM A126 CL.B G-203 Stem Bronze ASTM B138 G-204 Hand Wheel (not shown) Cast Iron ASTM A126 CL.B G-205 Stem Nut Bronze ASTM B62 G-206 Guide Cap Bearings Celcon G-207 Stuffing Box Ductile Iron ASTM A536 G-208 Anti-friction Washers (2) Brass G-209 Wedge, Rubber Encapsulation Ductile Iron* SBR ASTM A G-210 Bonnet Ductile Iron ASTM A536 G-211 Bonnet O-ring Rubber G-212 Body Ductile Iron ASTM A536 * Fully encapsulated in molded rubber with no iron exposed SEE PAGE FOR ORDERING INSTRUCTIONS G-49 G-202 G-200 G-207 G-41 G-201 G-208 G-203 G-210 G-16 G-211 G-205 G-212 G-209 G-206
UL / FM B-1 FIRE PROTECTION PRODUCTS MUELLER 2300 SERIES RESILIENT WEDGE GATE VALVE DESIGN FEATURES
UL / FM MULLR 2300 SRIS RSILINT WDG GAT VALV DSIGN FATURS SCTION Rev. 3-11 Mueller 2300 Series Resilient Wedge Gate Valves Mueller Resilient Wedge Gate Valves have features to make them easier to operate
More information4. Combi valves. 7. Fire hydrants. 8. Check valves. 9. Air valves
1. General company and product information 2. Flanged gate valves for water 3. Other gate valves for water 4. Combi valves 5. Service connection valves for water 6. Valves and fittings for gas 7. Fire
More informationPipe Repair Products A complete selection for all types of pipe
Pipe Repair Products A complete selection for all types of pipe Mueller Service Saddles Manufactured and tested in accordance with ANSI/AWWA C800 & NSF 61 certified. Mueller service saddles, available
More informationMueller. Pipe Repair Products. Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source.
Mueller Pipe Repair Products Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source. SERVICE SADDLES Mueller service saddles, available in bronze,
More informationMechanical Joint Restraints
-15 PVC Pipe Restrainer The PVC mechanical joint restrainer eliminates the need for thrust blocking, tie rodding, or harnessing mechanical joint fittings when they are used with PVC pipe. The key to the
More informationTelescoping Post Indicator Wall Post KENNEDY VALVE ISO 9000 ISO 14001
Telescoping Post Indicator Wall Post KENNEDY VALVE ISO 9000 ISO 14001 Telescoping Post Indicator 2945 A 1" SQUARE STEM 9" MAX. = 10" MIN. = 7" FIELD ADJUSTMENT INSTRUCTIONS 1. Remove the top section from
More informationMueller B-101 and A-3 Drilling and Tapping Machines
TM TM Mueller and Drilling and Tapping Machines A guide to selecting Mueller Equipment Mueller TM TM and Drilling and Tapping Machines When it comes to line stopping and drilling and tapping technology
More informationBritish Standard Underground Hydrant Range
British Standard Underground Hydrant Range 2 THE NEW AVK BRITISH STANDARD HYDRANT RANGE AVK are the renowned market leading innovators, manufacturers and suppliers of BS 750 fire hydrants into the UK,
More informationSection 3510: Reclaimed water Pipes, Valves, and Appurtenances February 11, 2011
STANDARDS AND CONSTRUCTION MANUAL : Reclaimed water Pipes, Valves, and Appurtenances February 11, 2011 PART 1 - GENERAL 1.01 SCOPE OF WORK A. These specifications cover the pipes, fittings, and appurtenances
More information60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
More informationSECTION 33 11 00.15 DUCTILE IRON PIPE AND FITTINGS
SECTION 33 11 00.15 DUCTILE IRON PIPE AND FITTINGS PART 1: GENERAL 1.01 COORDINATION OF WORK Connection to existing pipelines may require shutdown of AW facilities. Closely coordinate construction work
More informationINDICATOR POST STYLE 2945 A TELESCOPING BARREL ASSEMBLY UL AND FM APPROVED
INDICATOR POST STYLE 2945 A TELESCOPING BARREL ASSEMBLY UL AND FM APPROVED Available in Sizes B C D E See Page 6 for Dimensions Kennedy Valve/Indicator Posts 17-1 INDICATOR POST STYLE 2945 A TELESCOPING
More information08003-1 WATER SERVICE 2
08003_Mar08_2011.pdf Page 1 of 7 INDEX Page 08003-1 WATER SERVICE 2 1.1 Pipe 2 1.1.1 Copper 2 1.1.2 Polyethylene 2 1.2 Valves and Fittings 2 1.2.1 Main Stops 3 1.2.2 Curb Stops 3 1.2.3 Curb Box 3 1.2.4
More informationAmerican- Darling 5¼" B-84-B-5.
-5 Sealed Lubrication Chamber Seals operating threads from water and debris which greatly reduces routine maintenance. Top Travel Stop Nut Helps prevent stem buckling and damage to bronze components which
More informationRUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a wafer valve designed for a wide range of industrial applications. The double-seated design provides bi-directional shut off. The design of the valve
More informationBUTTERFLY VALVES. An industry leader in underground and in-plant applications. STYLE 4500 3 24 STYLE 1450 30 54. Consult factory for sizes 60 120
An industry leader in underground and in-plant applications. BUTTERFLY VALVES STYLE 4500 3 24 STYLE 1450 30 54 Consult factory for sizes 60 120 C504 Class 150B & 250B M&H Valve is a division of McWane,
More informationBUTTERFLY VALVES. An industry leader in underground and in-plant applications. STYLE 4500 3 24 STYLE 1450 30 54. Consult factory for sizes 60 120
An industry leader in underground and in-plant applications. BUTTERFLY VALVES STYLE 4500 3 24 STYLE 1450 30 54 Consult factory for sizes 60 120 C504 Class 150B & 250B M&H Valve is a division of McWane,
More informationWater Distribution Products Full-line product offering
Water Distribution Products Full-line product offering Contents 03 Hydrants and Hydrant Security 04 Main Valves 05 Pipe Repair Products 06-07 Service Brass 08 Machines and Tools 09-10 Intelligent Water
More informationSTORAGE, INSTALLATION AND MAINTENANCE PROCEDURES
GATE VALVE O.S. & Y 1.0 Periodic Inspections 1.1 The valve stem packing should be inspected at least monthly. If the stem packing shows signs of leakage, simply tighten the adjusting nuts to compress the
More informationSECTION 15105 DUCTILE IRON PIPE AND FITTINGS
SECTION 15105 DUCTILE IRON PIPE AND FITTINGS PART 1 GENERAL.01 COORDINATION OF WORK Connection to existing pipelines may require shutdown of Owner facilities. Closely coordinate construction work and connections
More informationOPERATION AND MAINTENANCE MANUAL 5-1/4 B-84-B-5 FIRE HYDRANT
OPERATION AND MAINTENANCE MANUAL 5-1/4 B-84-B-5 FIRE HYDRANT INDEX AMERICAN - DARLING 5-1/4 IN. B-84-B-5 FIRE HYDRANT OPERATION AND MAINTENANCE MANUAL OPERATION AND MAINTENANCE REPAIRS Operation and Maintenance...
More informationFord Pipe Repair Products The Ford Meter Box Company, Inc.
Section L 7/2008 Ford Pipe Repair Products The Ford Meter Box Company, Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260-563-3171 FAX: 800-826-3487 Overseas FAX:
More information2013 Edition. Flanged fittings 30"-64" NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61
30"-64" Ductile Iron industrial Applications, water & Wastewater 2 Table of Contents Flanged Fittings for Water 3 Flange Details 5 Flanged Fittings 6 90º and 45º Bend 6 22-1/2º and 11-1/4º Bends 7 Tees
More informationPRESSURE REDUCING CONTROL VALVE
Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING CONTROL VALVE with LOW FLOW BY-PASS FEATURE Main Line
More informationThese features have made Lo Torc valves the choice of high pressure plug value users, worldwide:
LO TORC Plug Valve The high value, dependable performance, and low maintenance requirements of Halliburton Lo Torc valves can help reduce overall operating costs and help cut downtime. These features have
More informationMustang Series PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE. M115-2 (Globe) M1115-2 (Angle) Schematic. Standard Components
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Throttles to maintain minimum upstream pressure PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE
More informationMueller. Pipe Repair Products. A complete selection for all types of gas lines... all from a single source. GAS PRODUCTS DIVISION
Mueller Pipe Repair Products A complete selection for all types of gas lines... all from a single source. GAS PRODUCTS DIVISION MUELLER STAINLESS STEEL REPAIR CLAMPS Mueller offers a full line of stainless
More informationSERIES ASM NEOPRENE/EPMD FLANGED SINGLE SPHERE CONNECTOR CONNECTORS. Pressures to 225 PSIG (15.51 barg) Temperatures to 230ºF (110ºC)
APPLICATIONS Process Industry Weak Acids Alkalies Compressed Air Pulp & Paper MODELS ASM - Flanged Connection OPTIONS Control Rods Oil & Gas Water & Waste Pump suction & discharge Sea water Chemical lines
More informationISORIA. Centered disc butterfly valves with AMRING elastomer liner. 240 PSI: 1½ to8. 150 PSI : 10 to 24
Type series booklet 8448.1/2-EN--US ISORIA Centered disc butterfly valves with AMRING elastomer liner 240 PSI: 1½ to8 150 PSI : 10 to 24 Design in accordance with ISO 10631 Manual, electrical, pneumatical
More informationDuctile Iron Pipe Couplings
J-9 Pipe 1 2 Straight and Transition Ductile offer an easy and economical way of joining whether the is of the same nominal and/or type or different at each coupling. couplings will handle most of your
More informationCHAPTER 6 PIPELINE MATERIALS, VALVES AND APPURTENANCES
VALVES AND APPURTENANCES 6.1 PIPELINE MATERIALS All pipe, fittings, packing, jointing material, valves, and fire hydrants shall be new and conform to Section C of AWWA Standards. All pipe material, solder
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationDeZURIK 3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT
3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT Instruction D10386 August 2013 Instructions These instructions provide installation, operation and maintenance information for BAW Butterfly Valves.
More informationFord Service Saddles and Tapping Sleeves
THE FORD METER BOX COMPANY, INC. ISO 9001:2008 10002505 Section AA 02/2015 Web Revision 12/17/2015 Ford Service Saddles and Tapping Sleeves Contents Page Recommended Product Application *Steel *C900 Cast
More informationRING JOINT SYSTEMS 207
RING JOINT SYSTEMS 07 08 Table of Contents Model R-88 Pages 10-11 Model R-88 Large Diameter Page 1 Model RH-1000 1000 PSI Coupling Page 13 Model RX-3000 3000 PSI Coupling Page 1 Model RX-3770 3770 PSI
More informationTECHNICAL SPECIFICATION
THOMAS - G-FLEX GFLEX TECH SPEC CONNECTING INNOVATION JOHANNESBURG TEL: +27 11 794 7594 CAPE TOWN TEL: +27 21 556 5258 POLOKWANE TEL: 015 298 9142 DESIGNER, MANUFACTURER AND DISTRIBUTOR OF PIPE CONNECTION,
More informationGeneral Guidelines for Repairing Buried PE Potable Water Pressure Pipes
515 General Guidelines for Repairing Buried PE Potable Water Pressure Pipes Introduction Traditional piping systems have gasket-sealed bell and spigot joints every 20 feet, which can be a potential maintenance
More informationRMF Engineering 23 05 23
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
More informationFire Hydrant Troubleshooting
Fire Hydrant Troubleshooting Pulsation or chatter during opening and flow of water from hydrant. Loose condition in stem at lower valve plate nut. Tighten lower valve plate nut and secure with SS lock
More information8D.1 BALL ANGLE METER VALVES - 3/4" & 1" P-24258 B-24258 E-24259 B-24259 B-24266 B-24267
BALL ANGLE METER VALVES - 3/4" & " 8D. B-24258 MUELLER 300 Ball Angle Meter Valve MUELLER 0 Conductive Compression Connection for CTS O.D.* tubing x meter swivel nut** adding -3 suffix to catalog number.
More informationDESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4
DESCRIPTION PAGE B7 Studs and Nuts Stud Bolts for Pressure-Temperature Piping 2-1 General Purpose End-to-End Studs 2-2 Tap End Stud Bolts 2-3 Double End Stud Bolts 2-4 Sigma Fasteners, Inc. Section 2 STUD
More informationAIR RELEASE, CLEANOUT, AND SEWER MANHOLES
AIR RELEASE, CLEANOUT, AND SEWER MANHOLES **From Hartford IM BLDG(10) DESCRIPTION. This work shall consist of the construction of air release, cleanout, and sanitary sewer manholes; and the furnishing
More informationAMERICAN Mechanical Joint Pipe For Water, Sewage or Other Liquids
AMERICAN Mechanical Joint Pipe For Water, Sewage or Other Liquids The AMERICAN Mechanical Joint was developed by the American Cast Iron Pipe Company and first marketed in 1929. Since that time, millions
More informationPOWERS Controls No. 4 Pneumatic Damper Actuator
POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000
More informationSECTION 02110 - ASBESTOS CEMENT PIPE REPAIRS, DEMOLITION, AND DISPOSAL
SECTION 02110 - ASBESTOS CEMENT PIPE REPAIRS, DEMOLITION, AND DISPOSAL PART 1 - GENERAL 1.1 WORK INCLUDED IN THIS SECTION A. The WORK of this Section includes the repair, demolition, and disposal of asbestos
More informationS GATE KNIFE GATE VALVE WITH PNEUMATIC ACTUATOR
MAIN FEATURES The pneumatic S GATE knife gate valve is intended for the automatic shut off of pipes of the heavy fluids like slurries and powders. The main fields of application are the water treatment,
More informationJames M. Pleasants Company
James M. Pleasants Company SUBMITTAL DATA GAINESVILLE MECHANICAL DECEMBER 20, 2013 PROJECT: GSU: J-183 HUMANITIES LAW BLDG. QUOTE NO:12116 ENGINEER: STEVENS & WILKINSON GASKETED PLATE HEAT EXCHANGER Tag:
More informationFisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation
Instruction Manual 1052 Size 20 Actuator (F & G) Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Contents Introduction... 1 Scope of manual... 1 Description... 1 Specifications...
More informationGAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES
GAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES CONTINENTAL INDUSTRIES ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and is today
More informationINDEX. Sec. No. Items Page Nos.
INDEX Sec. No. Items Page Nos. 1. Types of Pipe............... MSSP- 2 2. Concrete Pipe............... MSSP- 2 thru MSSP-3 3. ABS and PVC Truss Pipe............... MSSP- 3 4. ABS and PVC Solid Wall Pipe...............
More informationTwo most common lock nut groups: 1-Prevailing Torque Type Lock Nuts:
Two most common lock nut groups: 1. PREVAILING TORQUE a design feature of the lock nut produces friction between threads of mated components thereby increasing the force needed to tighten as well as loosen
More informationHilti, Inc. 5400 South 122 nd East Avenue Tulsa, OK 74146. 1-800-879-8000 www.hilti.com
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationWATER & SEWER CORROSIVE RESISTANT PRODUCTS
WATER & SEWER CORROSIVE RESISTANT PRODUCTS The Standard of Excellence in the Industry CASING SPACERS COUPLINGS & FLANGE COUPLING ADAPTERS REPAIR CLAMPS DUCTILE IRON SADDLES STAINLESS STEEL SADDLES TAPPING
More informationSECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS
SECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS PART 1 GENERAL 1.01 SECTION INCLUDES A. The requirements for pipe material and installation in sewer and drainage collection systems. All materials
More informationPLUMBING VALVES HOUSTON ORLANDO GREENVILLE 800/392-5066 800/327-3022 800/476-2212 TOTAL MAINTENANCE SOLUTIONS
8-1 BRONZE GATE VALVES 125 psi. SWP 200 psi WOG Threaded ends Non-rising stem Solid wedge disc DOMESTIC IMPORT PART # 40300250 1/4 40300260 40300251 3/8 40300261 40300252 1/2 40300262 40300206 3/4 40300263
More informationModel Specification 509 DRISCOPLEX 4200 and DRISCOPLEX 4300 Gravity Flow Sanitary Sewer
Model Specification 509 DRISCOPLEX 4200 and DRISCOPLEX 4300 Gravity Flow Sanitary Sewer The user may choose to adopt part or all of this Model Specification; however, the user should ensure that all parts
More informationSECTION 15056 DUCTILE-IRON PIPE AND FITTINGS
SECTION 15056 PART 1 GENERAL 1.01 DESCRIPTION This section includes materials and installation of ductile-iron pipe and fittings for potable and recycled water systems. A written request to use Ductile
More informationExperience In Motion. Valtek Spring Cylinder Linear Actuators
Experience In Motion Valtek Spring Cylinder Linear Actuators Valtek Spring Cylinder Linear Actuator Flowserve spring cylinder linear actuators are powerful, compact, high-performance pneumatic actuators
More informationBULLETIN 70.00-1 OCTOBER 2012. DeZURIK ROTARY DIAPHRAGM ACTUATORS
BULLETIN 70.00-1 OCTOBER 2012 DeZURIK ROTARY DIAPHRAGM ACTUATORS 2 2012 DeZURIK, Inc. Design & Construction DeZURIK rotary diaphragm actuators are available for use on rotary control valves including:
More informationMS-3/2009 HDPE (High Density Polyethylene) Pipe and Fittings Specification for Buried Potable Water
MS-3/2009 HDPE (High Density Polyethylene) Pipe and Fittings Specification for Buried Potable Water 105 Decker Court, Suite 825, Irving, TX 75062 P: 469-499-1044 F: 469-499-1063 www.plasticpipe.org HDPE
More informationPIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification. 96 B. Riutta
PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification Number: 3503-11.2.610 Rev. 2 Rubber Lined Steel Pipe and Fittings Mechanically Coupled Plain End Type System Issued Revised Approved
More informationSECTION 06000 WATER DISTRIBUTION SYSTEMS TABLE OF CONTENTS
SECTION 06000 WATER DISTRIBUTION SYSTEMS TABLE OF CONTENTS 06010 WATER DISTRIBUTION PIPE A. Design B. Materials C. Installation 06020 FIRE PROTECTION A. Fire Hydrants B. Automatic Fire Sprinkler Systems
More informationSECTION 15064 PVC PRESSURE PIPE AWWA C900
SECTION 15064 PVC PRESSURE PIPE (AWWA C900) PART 1 GENERAL 1.01 DESCRIPTION This section includes materials, installation, and testing of polyvinyl chloride (PVC) pressure pipe conforming to AWWA C900.
More informationQuality & Innovation, Manufactured in the U.S.A.
Quality & Innovation, Manufactured in the U.S.A. Repair Clamps Couplings Expansion Joints Pipe Restraint Service Saddles Dismantling Joints Tapping Sleeves Tapping Machines HDPE Pipe Products Line-Stop
More information1.8 CRANKSHAFT OIL SEALS
SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the
More informationTECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER 1.800.591.9360 TECHNICAL ASSISTANCE FAX: 1.626.855.4894
ACORN SAFETY P.O. BOX 3527 CITY OF INDUSTRY, CA 9744-0527 UNITED STATES OF AMERICA WWW.ACORNSAFETY.COM INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FREEZE RESISTANT WALL MOUNTED EMERGENCY EYEWASH
More informationBERMAD Waterworks. Pressure Relief/Sustaining Valve. 700 Series. Model 730. Features and Benefits. Major Additional Features
Pressure Relief/Sustaining Valve Prioritizing pressure zones Ensuring controlled pipeline fill-up Preventing pipeline emptying Pump overload & cavitation protection Safeguarding pump minimum flow Excessive
More informationSECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE
SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel
More informationSECTION 33 12 19 FIRE HYDRANTS
SECTION 33 12 19 FIRE HYDRANTS PART 1: GENERAL 1.01 SCOPE A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. 1.02 SUBMITTALS A. Conform to requirements of Section 01 33 00 - Submittals.
More informationSECTION 02401 - SANITARY SEWER PIPE
PART 1 - GENERAL 1.1 DESCRIPTION A. The WORK under this Section includes providing all labor, materials, tools and equipment necessary for furnishing and installing sanitary sewer pipe, in accordance with
More informationStyle 07 Zero Flex Rigid Coupling. Style 75 Flexible Coupling. Style 77 Flexible Coupling 11. Description
Style 07 Zero Flex Rigid Coupling The unique angled pad design adjusts to standard pipe tolerances to positively clamp the pipe to resist flexural and torsional loads. Working pressures are based on standard
More informationEngineering Specifications
PUREFLOW PEX PRODUCTS PART 1 GENERAL 1.1 SUMMARY 1.1.1 This specification covers Branch & Main, Parallel Water Distribution Systems (MANABLOC), Cross-linked Polyethylene tubing and fittings using PEX Press
More informationSECTION 33 11 00.11 POLYVINYL CHLORIDE (PVC) PIPE
SECTION 33 11 00.11 POLYVINYL CHLORIDE (PVC) PIPE PART 1: GENERAL 1.01 SECTION INCLUDES PVC pressure pipe and fabricated fittings in nominal sizes 4-inches through 12-inches with cast iron pipe equivalent
More informationStructural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the A325 structural bolt. Rev.
Structural Bolting ASTM A325 and ASTM A490 are the two U.S. standard structural bolts. When looking at the mechanical requirements of bolts it appears that an ASTM A325 and SAE J429 Grade 5 are identical
More information61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve
61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve Features Rounded polished disc edge gives full concentric sealing, lower torques, longer seat life
More informationInnovative Products For Unique Applications. A Tradition of Excellence. Creative Engineering for Fluid Systems. Earthquake Proof Valves
A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry Pratt Company became a trusted name in the flow control industry, setting the
More informationCAST IRON THE BASICS. Heatline - Cast Iron Radiators SMOOTH FLAT FILE TO REMOVE ANY SWARF. ONE TIME. ASSEMBLY. JOINTS SHOULD BE TIGHTENED.
CAST IRON THE BASICS 1. DO NOT LIFT ON YOUR OWN. 2. ONLY LIFT THE RADIATOR VERTICALLY. 3. DO NOT LIFT MORE THAN 8/10 SECTIONS AT ANY ONE TIME. 4. POSITION THE RADIATOR BEFORE FINAL ASSEMBLY. 5. THIS PRODUCT
More informationFLANGED END BALL VALVE
Specification: FLANGED END BALL VALVE - Chem Oil s two-piece ball valve has been designed to handle extreme service applications with unsurpassed reliability. Valve body machined from solid wrought material
More informationG. VULCANIZED SEAT Pressure sensitive seating with full disc overlap provides positive seating at high and low pressures.
A B C D G F E J H I A. RETAINER PLUGS Retain hinge and stop pins while providing compression to stabilization spheres. B. STABILIZATION SPHERES Stabilize hinge and stop pins, preventing vibration and wear.
More informationHOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). The special design of the
More information08.08 Vic-Check Valves
The check valves are a product of computer-assisted innovative engineering with quality features including a new hydrodynamically efficient profile. The Vic-Check valve utilizes a spring-assisted, single-disc
More informationEconosto UK. www.econosto.uk.com. LEICESTER Econosto UK Ltd Cambridge Road Whetstone Leicester LE8 6ZG T: +44 (0)116 272 7300 F: +44 (0)116 272 7345
LEICESTER Econosto UK Ltd Cambridge Road Whetstone Leicester LE8 6ZG T: +44 (0)116 272 7300 F: +44 (0)116 272 7345 ABERDEEN Econosto UK Ltd Blackness Road Altens Industrial Estate Aberdeen AB12 3LH T:
More informationEWE Ball Valve-Type Tapping Valve. EWE Ball-Type Tapping Valve. EWE GBM Tapping Valves. for water and gas
The following overview shows the different EWE tapping valves to help you to make your choice: EWE valve tapping valve for vertical tapping with operating shut-off, for all types of pipe, with external
More informationLathe Milling Attachment
Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,
More informationFULL FACE FLANGE-TYTE Gasket FOR FLANGED JOINTS
4"-64" FULL FACE FLANGE-TYTE Gasket FOR FLANGED JOINTS NSF FOR WATER & WASTEWATER, FIRE PROTECTION & INDUSTRIAL APPLICATIONS NSF P 2 Table of Contents Introduction 3 Pressure Performance 3 Torque Performance
More informationSports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049
Sports and High Mast Lighting Poles 4 High Mast Lighting Poles General American LitePole offers a raising and lowering system that allows for ease of maintaining the lighting system at ground level. Ideal
More informationFlygt Ball Check Valves
4/13 Supersedes: 6/96 The basic purpose of a check valve is to permit flow in one direction, prevent flow in the opposite direction and perform this function automatically and with minimum maintenance.
More informationFront axle components, overview
just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,
More informationCRANE. Σελίδα 1 από 2. Dimensions and Weights. Weight (kg) Size
CRANE Σελίδα από 2 DM93 Variable Orifice Double Regulating Valve PN6 Cast Iron Balancing Valve (VODRV), Flanged to BSEN 92-2 The DM93 variable orifice double regulating valves will give satisfactory performance
More informationSureSite Magnetic Liquid Level Indicator
SureSite Magnetic Liquid Level Indicator Instruction Bulletin No. 177664-1 (Rev. E) Section 1: Weldments Thank you for purchasing the GEMS SureSite Magnetic Level Indicator. Please read this document prior
More informationWorking Drawing and Assemblies. Chapter 10
Working Drawing and Assemblies Chapter 10 Objectives 1.Define working drawings. 2. Describe how working drawings are used in industry. 3. List the major components of a complete set of working drawings.
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)
17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure
More informationVogt Valves The Connection Bulletin for Extended Body Forged Steel Valves Welded Bonnet, Bolted Bonnet, Class 800 & Class 1500 CB 22
The Connection Bulletin for Extended Body Forged Steel Valves Welded Bonnet, Bolted Bonnet, Class 800 & Class 1500 CB 22 Extended Body Forged Steel Valves An extended body gate valve specifically designed
More informationENGINEERED & PROCESS VALVES. Installation, Operation and Maintenance Manual GENERAL VALVE. Twin Seal Double Block and Bleed Plug Valve GENERAL VALVE
GENERAL VALVE Twin Seal Double Block and Bleed Plug Valve GENERAL VALVE 2 TABLE OF CONTENTS GENERAL VALVE TWIN SEAL Installation.... 4 Operation.... 5 Series 400, 800 & 900 Integral Bushing/Retained Ring
More informationCopper Meter Resetters
Copper Meter Resetters To Set 5/8", 5/8" x 3/4", 3/4", 1", 1 1 2" & 2" Water Meters 11/12 Table of Contents Page Page Meter Resetters 5/8", 5/8" x 3/4", 3/4", & 1" Horizontal Inlet and Outlet Series 710
More informationInstallation, Operating and Maintenance Instructions for AEON Metal Seated Gate Valve (MSGV) Water
1 Foreword 1.1 Thank you for choosing one of the range of AEON's BS standard valves. For safety purposes, the user shall read this instruction to fully understand the operation of the product. 2 AEON Design
More informationJCM GENERAL PRODUCT DIRECTORY Effective March 1, 2010 Replaces 01/12/2007
JCM GENERAL PRODUCT DIRECTORY Effective March 1, 20 Replaces 01//2007 UNIVERSAL CLAMP COUPLINGS / REPAIR FITTINGS Page 1 Universal Clamp Coupling - Standard Range...4-2 Universal Clamp Coupling - Extended
More informationVM Series Manual Diaphragm Valves Product Data Sheet. Valve Availability. Size Range: 1/2" through 4" EPDM, Viton (FPM) or PTFE (EPDM backed)
Product Data Sheet introduction < STANDARDS > ASTM D4101-86 ASTM D3222 ASTM D2467 ASTM D2466 ASTM D1785 ASTM D1784 ASTM F441 ASTM F439 IPEX VM Series Diaphragm Valves are the ideal solution f modulating
More informationPPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES
PPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES BUSHING WITH PLUG CONNECTION WITH OUTER CONE PPS CHARACTERISTICS The PPS bushing can be used as a fixed section for the entry of medium
More informationESFR DRY PENDENT SPRINKLER VK502 (K14.0) TECHNICAL DATA
December 19, 2013 Sprinkler 122j 1. DESCRIPTION Viking Early Suppression Fast Response (ESFR) Dry Pendent Sprinkler VK502 is a fast response fusible element type sprinkler designed for use in storage areas
More information