Process Calibration & Test Equipment

Transcription

1 Multifunction Calibrators Const 318A Measures and source 13 T/Cs, 11 RTDs, mv, ma, Ohms, frequency and pulses, with accuracy to 0.01% of reading Pressure via external pressure modules up to 70,000kPa 24V loop power HART communication capability Task management capability, upload, download and document Easy to use smartphone type menu and interface Rugged design for use in harsh environments DMC 1410 Measure and source T/Cs (13 types), RTDs (13types), Ohms, current, voltage, frequency, source pulse trains Isolated ma/v read-back circuit for complete transmitter calibration Pressure via external pressure modules up to 70,000kPa Built in 24V supply can drive 4-20mA loops Accuracy to 0.01% of reading Capture calibration data for 50 instruments with both As Found & As Left data Const 317A Measures and source 13 T/Cs, 11 RTDs, mv, ma, Ohms, frequency and pulses Accuracy to 0.01% of reading Pressure via external pressure modules up to 70,000kPa 24V loop power Task management capability, upload, download and document Easy to use smartphone type menu and interface Rugged design for use in harsh environments MC 1210 Measure and source T/Cs (13 types), RTDs (13types), Ohms, current, voltage, frequency, source pulse trains Isolated ma/v read-back circuit for complete transmitter calibration Pressure via external pressure modules up to 70,000kPa Built in 24V supply can drive 4-20mA loops Accuracy to 0.015% of reading

2 Multifunction Calibrators Const 316A Measures and source 13 T/Cs, 11 RTDs, mv, ma, Ohms, frequency and pulses Accuracy to 0.01% of reading 24V loop power Task management capability, upload, download and document Easy to use smartphone type menu and interface Rugged design for use in harsh environments MC T/C types and 8 RTD types, plus YSI 400 Read and source modes Full function 4 to 20 ma read, source, simulate and read/power modes with ±0.015% of reading accuracy Source or read 0 to 20 volts (±0.015 of reading accuracy) Measure 0 to 250 VDC or VAC Direct keyboard entry enables quick output changes RTD function compatible with all pulsed transmitters 3001 Lab Calibrator %calibration accuracy Source/Read thermocouples, RTDs, Voltage, current and pressure Custom RTD and SPRT profiles RS-232, USB and IEEE-488 remote control Compatible with Fluke Met/Cal Software Isolated measurement channel M2000 Lab Calibrator % calibration accuracy Direct keyboard entry or cursor entry with decade control Automatic standby function protects device under test Nine set points for each output range Local or RS232 remote control IEEE-488 control Compatible with Fluke Met/Cal Software Optional rack / panel mount kit available

3 Temperature Calibrators PTC-8010 Calibrate thermocouples and RTD s with one unit Works with smart transmitters Direct keyboard entry or scroll control of output User defined set points High accuracy ±0.4 C J T/C and ±0.3 C 4W PT385 RTD; all errors included 13 thermocouple types and 13 RTD types Supplied in full rubber boot Stores up to 9 set points for each output function TC-100 High accuracy ±0.3 C type J T/C all errors combined Ten common T/C types plus mv Accepts both T/C mini plug and bare T/C wires Simple decade control of output Three set points for each T/C type Min/Max recall in measure mode Input protection to 240 VAC Supplied in full rubber boot

4 Pressure Calibrators Const 811 Integral electric pump generates pressure from 90 % vacuum up to 2500 kpa Measure up to 70 MPa with optional external pressure modules Accuracy 0.02% FS, pressure control stability 0.005% FS Fully automated pressure calibration Task management capability, upload, download and document Compact, portable and light weight HART communication capability with 24 volt loop power supply 7 LCD colour screen with on screen Help menu BG 330 Integrated electrically operated pump generates pressure up to 2000 kpa and vacuum up to 80 kpa External pressure module interface supports all 29 BetaPort-P pressure modules Accuracy to 0.025% FS 24 Volt loop power to operate device under test Switch test is automatic using internal sensor or external pressure module Store and recall up to 5 user defined setups BG 321A / 311A Two isolated (321) or one single (311), stainless steel, pressure sensors with 0.025% F.S. accuracy External pressure module interface supports BetaPort-P pressure modules Measures 4-20 ma input Measures up to 30 V DC Large graphic style LCD with backlight Pressure switch test function % Error and damping functions BG 321A EX / 311A EX IECEX Ex ia IIB T3 for hazardous area use Two isolated (321) or one single (311), stainless steel, pressure sensors with 0.025% F.S. accuracy Measures 4-20 ma input Measures up to 30 V DC Large graphic style LCD with backlight Pressure switch test function % Error and damping functions

5 Pressure Calibrators Const 273 Series Suitable for gauge pressure, compound pressure or absolute pressure Pressure ranges up to 250,000 kpa Accuracy up to 0.025% FS Pressure switch test Hart communication capability and 24 volt loop power supply Large, easy to read, back lit screen with dual display Min/Max/Hold to capture changing measurements Data Logging Const 273 Series Suitable for differential pressure Pressure ranges up to 10 kpa Accuracy up to.05 % FS Pressure switch test Hart communication capability and 24 volt loop power supply Large, easy to read, back lit screen with dual display Min/Max/Hold to capture changing measurements Data Logging BG 301 Single sensor pressure calibrator Full scale accuracy on all pressure ranges of ±0.05% FS External pressure module interface supports BetaPort-P pressure modules Measures 4-20 ma input Measures up to 30 V DC Large graphic style LCD with backlight Pressure switch test function % Error and damping functions T 140 High accuracy gauge and differential capability Rugged, dust tight, water-resistant case Isolated SS sensors on 300 psi and 3,000 psi units Easy to read LCD Intuitive controls make operation easy Powered by a 9 Volt alkaline battery Supplied in neoprene sleeve

6 Loop / Signal Calibrators PSC-4010 Easy to use intuitive interface Reads and simulates process control signals voltage, current and frequency Multiple input/output ranges for current, frequency and voltage modes Built-in 24 VDC source for powering two wire transmitters Accuracy ± 0.015% of reading Supplied in full rubber boot Const 312 Easy to use smartphone type menu and interface Sources and reads voltage and current Reads frequency 24V loop power supply Accuracy ± 0.01% of reading Displays max, min, peak-to-peak, average and percentage simultaneously Data logging stores up to 20,000 records Rugged design for use in harsh environments LC-110H Accuracy at 0.01% Reading 24VDC loop power with ma Measure Mode (-25% to 125%) Built in selectable 250 Ohms Resistor for HART Communications Adjustable Span and Valve Test (simulate defined ma values with % keys) Data log capacity of 9800 records or 99 individual sessions HART communications for universal and common practice commands Capture 20 transmitter configurations for upload via BetaLOG HART software Monitor PV unit, PV, PV ma, PV % and Trim DAC zero/gain IVC 222 HPII Very high accuracy ±0.015% of reading Four ranges: 200 mv, 2V, 20V and 24 ma RS-232 interface allows computer control Built-in 24V power supply can drive 4 to 20 ma loops over 1000 Ohms Rugged, lightweight, hand-held unit Includes test leads, carry case, 9V battery

7 Loop / Signal Calibrators LC-100 High accuracy of ±0.015%, high resolution of 0.001mA / 0.001V % Error function eliminates manual error calculation Reads 0 to 28.0 VDC Built-in 250 Ohm resistor facilitates calibration of HART Devices Automatic Step and Ramp functions allow for remote calibrations Loop power measurements capability Simulates, powers and measures two wire transmitters Five pre-set outputs (4, 8, 12, 16, 20 ma)

8 Digital Test Gauges Beta Gauge PIR Pro Test Gauge High accuracy ±0.04% of reading, temperature compensated 0 to 50 C Displays in multiple engineering units Large, back-lit easy to read display MIN/MAX recall and adjustable TARE Full rubber boot cover BetaLog data logging software optional Optional 24V external power input Beta Gauge PI Pro Test Gauge High accuracy ±0.05% full scale, temperature compensated 0 to 50 C Displays in multiple engineering units Displays ambient temperature in degrees C or degrees F Large, back-lit easy to read display MIN/MAX recall and adjustable TARE Full rubber boot cover BetaLog data logging software optional Optional 24V external power unit Const 211 Series Digital Pressure Gauges Choice of accuracy levels 0.2%, 0.1%, 0.05% & 0.025% FS Pressure ranges up to 250,000 kpa Suitable for gauge pressure, compound pressure & absolute pressure Selectable engineering units Large back-lit easy to read display % pressure indication with fan shaped graph scale for visual reference Display flash warning when pressure over 120% of FS ATEX certified model available Const 211 Series Differential Digital Pressure Gauges Choice of accuracy levels 0.4%,0.2%, 0.1% & 0.05% FS Pressure ranges up to 10 kpa Suitable for differential pressure Selectable engineering units Large back-lit easy to read display % pressure indication with fan shaped graph scale for visual reference Display flash warning when pressure over 120% of FS ATEX certified model available