MATERIAL SAFETY DATA SHEET

Transcription

1 Starline 2000-Adhesive, Component A Prepared By: Progressive Pipeline Management Starline Trenchless Technologies Reference No. PPMSTT2000A Effective Date: SECTION 1: CHEMICAL PRODUCT & COMPANY IDENTIFICATION PRODUCT NAME: PRODUCT TYPE: GENERAL USE: CHEMICAL NAME: Starline 2000-Adhesive, Component A Polyurethane adhesive for industrial bonding applications Industrial adhesive used for Starline Cured-In-Place Lining Technology Polyol Formulation with Inorganic Fillers EMERGENCY TELEPHONE NUMBER(S): INFOTRAC (800) (For transportation incidents only ) STARLINE (847) (Manufacturer ) PPM (732) (Supplier ) MANUFACTURER: Starline Trenchless Technologies, LLC Starline Technologietransfer GmbH 1700 Mount Prospect Road South Hegauer weg 25 Des Plaines, IL D Berlin, Germany (847) / (847) fax (011) / fax: 41 SECTION 2: COMPOSITION INFORMATION / INGREDIENTS OTHER HAZARDOUS COMPONENTS CAS NO. OSHA PEL ACGIH TLV LIMITS No Hazardous Components

2 Page: 2 of 7 SECTION 3: HAZARD IDENTIFICATION EMERGENCY OVERVIEW: Thick white liquid with sweet odor. Avoid direct prolonged contact with skin and eyes. When mixing with Starline 2000 Adhesive, Component B, do so in a well ventilated area when indoors. POTENTIAL HEALTH EFFECTS ROUTES OF ENTRY: Inhalation.MILD Skin.....MILD Ingestion..MODERATE Eye MODERATE EFFECTS OF ACUTE EXPOSURE: SKIN CONTACT: Repeated of prolonged exposure may cause slight irritation. EYE CONTACT: Irritation INHALATION: At normal conditions, no effects INGESTION: Gastrointestinal irritation OVER EXPOSURE: No acute effects CARCINOGENICITY: Not Listed - Not considered a carcinogen Medical Conditions Generally Aggravated By Exposure: NONE KNOWN SECTION 4: FIRST AID & EMERGENCY PROCEDURES SKIN: Remove contaminated clothing and wash area with water and, if available, mild soap. Seek medical attention if irritation occurs. EYES: Flush eyes immediately with large amounts of water for approx. 15 minutes. Seek medical attention if irritation occurs. INGESTION: Do not induce vomiting. Give two glasses of water to dilute stomach contents. Never give anything by mouth to an unconscious person. Seek medical attention. INHALATION: In case of inhalation of fumes resulting in throat irritation and/or coughing, remove person to fresh air. Provide oxygen if symptoms persist, and seek prompt medical attention.

3 Page: 3 of 7 SECTION 5: FIRE FIGHTING MEASURES FLASH POINT: > 390º F (>200ºC) EXTINGUISHING MEDIA: Foam, CO2, Dry Chemical, Water, etc. SPECIAL FIRE FIGHTING PROCEDURES: Follow normal procedures for chemical fires. UNUSUAL FIRE & EXPLOSION HAZARDS: None INCOMPATIBILITY (MATERIALS TO AVOID): Unknown Chemicals HAZARDOUS DECOMPOSITION OR BYPRODUCTS: None SECTION 6: ACCIDENTAL RELEASE MEASURES LAND SPILL: For small spills use absorbent materials such as towels or absorbent powders. Put all material in proper waste disposal container with lid tightly covered. For large spills or dyke spills recover free flowing liquid and use absorbent material to dry area. Rinse area with water. WATER SPILL: Remove product from water surface by skimming or with suitable absorbents. This product contains surfactants that will cause it to disperse in water. Check with local environmental regulatory agencies for reporting requirements. SECTION 7: HANDLING & STORAGE HANDLING PRECAUTIONS: Curing of the adhesive should be performed in a well-ventilated area. If possible remove fumes through dedicated local exhaust system. Inhalation of vapors should be avoided. Apply skin protective cream before handling. Avoid prolonged or repeated contact with skin. Wash hands and other exposed body areas before eating. Protective Equipment in Section 8 should be worn. STORAGE PRECAUTIONS: Store in tight containers. Keep away from heat, moisture, food and beverages. Keep at temperatures between 36 o F and 104 o F (2 o 40 o C). SECTION 8: EXPOSURE CONTROLS & PERSONAL PROTECTION PROTECTIVE EQUIPMENT: Safety glasses are recommended for all work place conditions. Splash proof goggles, face shields and chemical resistant, nitrile or rubber gloves should be worn.

4 Page: 4 of 7 RESPIRATORY PROTECTION: Under normal conditions of use, this material does not present any unusual hazards. Respiratory protection is not required VENTILATION: None needed under normal use conditions. For enclosed areas with poor ventilation or when large quantities of product are used, fans or other mechanical ventilation devices is recommended. SECTION 9: PHYSICAL & CHEMICAL PROPERTIES PHYSICAL FORM: COLOR: ODOR: SOLUBILITY IN WATER: VAPOR DENSITY: VAPOR PRESSURE: SPECIFIC GRAVITY: BOILING POINT: Ph: Liquid White Slight sweetish odor Not miscible 1.6 (H 2 O=1) SECTION 10: STABILITY AND REACTIVITY DATA CHEMICAL STABILITY: o F HAZARDOUS DECOMPOSITION PRODUCTS: No unusual hazardous decomposition. POLYMERIZATION: Polymerization of this material should not occur. INCOMPATIBILITIES: No incompatibility known. SECTION 11: TOXICOLOGICAL INFORMATION EYE EFFECTS: This material may cause significant irritation to the eyes. SKIN EFFECTS: This material may cause significant irritation to the skin. HEALTH HAZARDS (ACUTE & CHRONIC): Overexposure may cause only slight irritation. DERMAL LD 50 : No ORAL LD 50 : No

5 Page: 5 of 7 INHALATION LC 50 : No SENSITIZATION DATA: No TARGET ORGANS: Eyes & Skin CARCINOGENICITY: IARC: Listed by IARC - No NTP: Listed by NTP - No OSHA: Listed by OSHA No SECTION 12: ECOLOGICAL INFORMATION ENVIRONMENTAL DATA: May cause adverse environmental impact if material reaches waterways. ECOTOXICOLOGICAL INFORMATION: Not Available DISTRIBUTION: Not Available CHEMICAL FATE INFORMATION: None known SECTION 13: DISPOSAL INFORMATION All solid and liquid waste should be disposed of in accordance with federal, state and local regulations. Excess or spilled product should be recovered and placed in air-tight containers. DISPOSAL METHOD: This product should be mixed with Starline 2000 Adhesive, Component B and allowed to cure for 12 hours at 60 F prior to disposal. The combined material meets the following criteria for disposal classification : 1.) Ingredients are not RCRA listed wastes. 2.) Not ignitable or corrosive, no dangerous properties and evolves no toxic chemical in leaching procedures. Therefore, the product is not considered a hazardous waste, but should be disposed of at a commercial landfill. SECTION 14: TRANSPORT INFORMATION DOT CLASSIFICATION: HAZARDOUS CLASS: SHIPPING NAME:

6 Page: 6 of 7 SECTION 15: REGULATORY INFORMATION WORKER RIGHT-TO-KNOW: This material is not considered hazardous under the OSHA Hazard Communications Standard (29 CFR ) EXPOSURE LIMITS (OSHA AND ACGIH): TLV (ACGIH): No existing limits PEL (OSHA): No existing limits STEL (OSHA / ACGIH): No existing limits HAZARDOUS MATERIAL IDENTIFICATION SYSTEM (HMIS): HEALTH 1 FLAMMABILITY 1 REACTIVITY 1 PROTECTION B SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT) FIRE: NO PRESSURE GENERATING: NO REACTIVITY: NO ACUTE: NO CHRONIC: NO 313 REPORTABLE INGREDIENTS: Not Applicable TITLE III NOTES: Not Applicable CERCLA (COMPREHENSIVE RESPONSE, COMPENSATION, AND LIABILITY ACT) CERCLA RQ: Not Applicable TSCA (TOXIC SUBSTANCE CONTROL ACT) TSCA REGULATORY: All ingredients are listed on the TSCA Inventory.

7 Page: 7 of 7 SECTION 16: OTHER INFORMATION FOR INDUSTRIAL USE ONLY USE LOCATION: Indoors or Outdoors / Good ventilation when mixing QUANTITY USED: 0.02 lbs per foot of liner CONTAINER TYPE: Re-usable air tight plastic bottle CONTAINER SIZE: 4 lbs TEMPERATURE: Ambient - Stable in all temperatures PRESSURE: No significant change or affect during mixing or curing APPLICATION: Product is mixed with Starline Adhesive, Component B and poured into Starline Hose Liner through a funnel. Mixed adhesive is absorbed into felt backing of the Hose Liner and comes into contact with the surface of the pipe (or vent) during the inversion process.