Supplementary instructions Sigmas with hygienic pump head

Transcription

1 Supplementary instructions Sigmas with hygienic pump head EN Two sets of operating instructions are required for the safe, correct and proper operation of the metering pumps: This set of supplementary instructions and the corresponding "Operating instructions for the diaphragm motor driven metering pump Sigma". Both sets of operating instructions are only valid when read together. Please carefully read these operating instructions before use. Do not discard. The operator shall be liable for any damage caused by installation or operating errors. The latest version of the operating instructions are available on our homepage. Part no BA SI /15 EN

2 Table of contents Table of contents 1 Sigma Sigma 1 Performance Data Wetted Materials Dimensional Drawings of Sigma Spare Parts Lists for Sigma Sigma Sigma 2 Performance Data Wetted Materials Dimensional Drawings of Sigma Spare Parts Lists for Sigma Sigma Sigma 3 Performance Data Wetted Materials Dimensional Drawings of Sigma Spare Parts Lists for Sigma Intended Use Assembly of the Hygienic Pump Head Notes on Cleaning Metering Pumps with Hygienic Pump Head EHEDG Certificate

3 Sigma 1 1 Sigma Sigma 1 Performance Data S1Ba with hygienic pump head at 50 Hz operation Type Minimum pump capacity at maximum back pressure Maximum stroke rate Priming lift Connector size bar l/h ml/stroke Strokes/min m WS DN All figures are guideline figures for water at 20 C. The priming lift applies to clean, moist valves, an empty suction line and empty liquid end - with correct installation (valve springs reduce the values). S1Ba with hygienic pump head at 60 Hz operation Type Minimum pump capacity at maximum back pressure Maximum stroke rate Priming lift Connector size bar l/h ml/stroke Strokes/min m WS DN All figures are guideline figures for water at 20 C. The priming lift applies to clean, moist valves, an empty suction line and empty liquid end - with correct installation (valve springs reduce the values). 3

4 Sigma 1 S1Cb with hygienic pump head Type Minimum pump capacity at maximum back pressure Maximum stroke rate Priming lift bar l/h ml/stroke Strokes/min m WS DN All figures are guideline figures for water at 20 C. Connector size The priming lift applies to clean, moist valves, an empty suction line and empty liquid end - with correct installation (valve springs reduce the values). 1.2 Wetted Materials Dosing head Valve housing Seals / diaphragms Inner part PTFE /EPDM 4

5 Sigma Dimensional Drawings of Sigma 1 Dimensional drawing of Sigma 1, S1Cb with hygienic pump head P_SI_0157_SW Fig. 1: Dimensional drawing of Sigma 1, S1Cb with hygienic pump head - dimensions in mm 5

6 Sigma Spare Parts Lists for Sigma 1 Sigma 1 with hygienic pump head A A 61_05-104_01_45 Item Type Quantity Article Order no. 104 A, B Hyg. connection set TCVC DN C Hyg. connection set TCVC DN A-C Hyg. valve seal TCVC A-C Hyg. valve inner part EPDM with seal A, B Hyg. valve top part TCVC DN C Hyg. valve top part TCVC DN A, B Hyg. valve bottom part TCVC DN A Hyg. valve bottom part TCVC DN A- B Hyg. clamp connection TRICLAMP TCVC A Diaphragm 70 x 32 -M6 PTFE B Diaphragm 70 x 37 -M6 PTFE C Diaphragm 77.0x M5 PTFE A, B Cyl. screw DIN 912 M 5x C Cyl. screw DIN 912 M 5x

7 Sigma 2 2 Sigma Sigma 2 Performance Data S2Ba with hygienic pump head at 50 Hz operation Type Minimum pump capacity at maximum back pressure Maximum stroke rate bar psi l/h gph ml/stroke Strokes/ min Priming lift m WS Connector size DN All figures are guideline figures for water at 20 C. The priming lift applies to a filled suction line and filled liquid end - with correct installation. S2Ba with hygienic pump head at 60 Hz operation Type Minimum pump capacity at maximum back pressure Maximum stroke rate bar psi l/h gph ml/stroke Strokes/ min Priming lift m WS Connector size DN All figures are guideline figures for water at 20 C. The priming lift applies to a filled suction line and filled liquid end - with correct installation. S2Cb with hygienic pump head Type Minimum pump capacity at maximum back pressure Maximum stroke rate bar psi l/h gph ml/stroke Strokes/ min Priming lift m WS Connector size DN All figures are guideline figures for water at 20 C. The priming lift applies to a filled suction line and filled liquid end - with correct installation. 7

8 Sigma Wetted Materials Dosing head Valve housing Seals / diaphragms Inner part PTFE /EPDM 2.3 Dimensional Drawings of Sigma 2 Dimensional drawing of Sigma 2, S2Cb with hygienic pump head Fig. 2: Dimensional drawing of Sigma 2, S2Cb with hygienic pump head - dimensions in mm P_SI_0158_SW 8

9 Sigma Spare Parts Lists for Sigma 2 A A 61_05-104_01_46 Item Type Quantity Article Order no. 104 A Hyg. connection set TCVC DN B Hyg. connection set TCVC DN A, B Hyg. valve seal TCVC A,-C Hyg. valve inner part EPDM with seal A Hyg. valve top part TCVC DN B Hyg. valve top part TCVC DN A Hyg. valve bottom part TCVC DN B Hyg. valve bottom part TCVC DN A, B Hyg. clamp connection TRICLAMP TCVC A Diaphragm 86.5x 46.0 P B Diaphragm 123.5x 75.0 P A Hexagon screw DIN 931 M 6x B Hexagon screw DIN 931 M 6x

10 Sigma 3 3 Sigma Sigma 3 Performance Data S3Ba with hygienic pump head at 50 Hz operation Type Minimum pump capacity at maximum back pressure Maximum stroke rate Priming lift Connector size bar l/h ml/stroke Strokes/min m WS DN All figures are guideline figures for water at 20 C. The priming lift applies to a filled suction line and filled liquid end - with correct installation. S3Ba with hygienic pump head at 60 Hz operation Type Minimum pump capacity at maximum back pressure Maximum stroke rate Priming lift Connector size bar l/h gph ml/stroke Strokes/min m WS DN All figures are guideline figures for water at 20 C. The priming lift applies to a filled suction line and filled liquid end - with correct installation. 10

11 Sigma 3 S3Cb with hygienic pump head Type Minimum pump capacity at maximum back pressure Maximum stroke rate Priming lift bar l/h gph ml/stroke Strokes/min m WS DN All figures are guideline figures for water at 20 C. Connector size The priming lift applies to a filled suction line and filled liquid end - with correct installation. 3.2 Wetted Materials Dosing head Valve housing Seals / diaphragms Inner part PTFE /EPDM 11

12 Sigma Dimensional Drawings of Sigma 3 Dimensional drawing of Sigma 3, S3Cb with hygienic pump head P_SI_0159_SW Fig. 3: Dimensional drawing of Sigma 3, S3Ca with hygienic pump head - dimensions in mm 12

13 Sigma Spare Parts Lists for Sigma 3 A A 61_05_104_01_47 Item Type Quantity Article Order no. 104 A Hyg. connection set TCVC DN B Hyg. connection set TCVC DN A, B Hyg. valve seal TCVC A-C Hyg. valve inner part EPDM with seal A Hyg. valve top part TCVC DN B Hyg. valve top part TCVC DN A Hyg. valve bottom part TCVC DN B Hyg. valve bottom part TCVC DN A, B Hyg. clamp connection TRICLAMP TCVC A Diaphragm 123.5x 75 - M B Diaphragm 178 x M A Hexagon screw DIN 931 M 6x B Hexagon screw DIN 931 M 8x

14 Intended Use 4 Intended Use Supplementary information to the 'Intended Use' in the "Operating Instructions for Sigma": The pump is only intended for use in sealed systems with CIP (cleaning in place) in the hygienic sector. (EHEDG-certified, type EL Class I) 14

15 Assembly of the Hygienic Pump Head 5 Assembly of the Hygienic Pump Head Select the hygienic pump head by its identity code under "Dosing head design" - "H hygienic pump head" (only with stainless steel pump heads). The hygienic head is supplied assembled on the pump (welded assembly (item 100)); the valves (item 104) are packed in bags. Assemble the pump so that the EHEDG symbol on the hygienic pump head is legible. Fit the valves (item 104) as shown on the Figure Make sure that the flat inner side of the valves is always facing downwards as well as the O-ring on the fastening body (item 122) - see Figure 61_05-104_01_46-04x01_B2 15

16 Notes on Cleaning Metering Pumps with Hygienic Pump Head 6 Notes on Cleaning Metering Pumps with Hygienic Pump Head General Metering pumps of the Sigma product range, fitted with hygienic head, are used to pump and meter high-grade, hygienically flawless and microbiologically sensitive liquids. They therefore need to be thoroughly cleaned at the end of a production process and be absolutely clean and free of germs that could be harmful to the product, or even pathogens, at the start of a new production process. ProMinent therefore recommends including the metering pumps in an HACCP and/or in-house hygiene scheme. Certification The cleaning-friendly construction of ProMinent metering pumps with hygienic pump head in compliance with the requirements of the EHEDG ( has been confirmed by the TU Munich-Weihenstephan Certification Office and correspondingly certified (EHEDG Type EL class I). Inclusion in CIP (Cleaning In Place) ProMinent recommends including metering pumps with hygienic pump head in the CIP (Cleaning in Place) process. This means that the pump is cleaned in a circular and/or continuous process without having to be dismantled. It involves the following steps, depending on the level of impurities: 1 - Pre-flushing with water 2 - Flushing with alkali 3 - Interim flushing with water 4 - Flushing with acid 5 - Flushing with clear water Flow velocity Fundamental prerequisite for a successful CIP (cleaning in place) is a turbulent flow at a minimum flow velocity of 1.5 m/s based on the pipe diameter of the pump inlet. Should this flow velocity not be reached due to the inherent capacity of the pump type, then a centrifugal pump should be installed upstream as a booster pump. However, never exceed the maximum permitted priming pressure on the suction side - see "Technical Data". Stroke rate and stroke length The metering pump should run at a minimum stroke rate of 72 strokes/min and at 100% stroke length during CIP (Cleaning in Place) to ensure that liquid flows perfectly through the hygienic pump head. Drainage of residual liquid / Self-draining Tightly sealed non-return valves are fitted in ProMinent metering pumps with hygienic pump head. That is why the dosing head needs to be manually drained after the CIP (Cleaning in Place) step by opening the clamps and/or using compressed air to ensure that any residual liquid is drained. In doing so it is imperative that you ensure using fittings and pipework that no cleaning solution can enter parts of the system that carry product. When using compressed air, use appropriate fittings and pipework to ensure that any residual liquid is fully blown out. Make sure that the pump is at a standstill when doing so. Materials of wetted parts The following wetted materials are used in ProMinent metering pumps with hygienic pump head: 16

17 Notes on Cleaning Metering Pumps with Hygienic Pump Head A A 61_05_104_01_47 Fig. 4 Item. no. Wetted materials 100 Stainless steel , 122, 123 Stainless steel PTFE 125 Gylon BIO PRO (PTFE material) Part of 122 EPDM, if item 122 has a seal Gylon BIO PRO is a registered trademark of Garlock Sealing Technologies Chemical resistance Check the resistance of the wetted parts to the CIP (Cleaning in Place) media used in detail. Temperature resistance ProMinent metering pumps with hygienic pump head can be exposed to temperatures of max. 120 C at 2 bar for a maximum of 15 minutes. Process connections ProMinent metering pumps with hygienic pump head are supplied as standard with welded ends in compliance with DIN Range 2. The pumps are dismantled by loosening the BIO CONNECT clamp connection by means of which the valves can be separated into a top and bottom half. Note this when designing the connecting pipework. Connection adapters can be customised and fitted at any time. Cleaning without CIP (Cleaning in place) Adapt the cleaning process if no CIP-compatible connections (e.g. milk pipe connectors DIN 11851, hose connectors, Clamp DIN 32676) are used or only used to a limited extent. 17

18 EHEDG Certificate 7 EHEDG Certificate 18

19 19

20 ProMinent GmbH Im Schuhmachergewann Heidelberg Germany Telephone: Fax: Internet: Heidelberg, 2, en_gb 2010