UPS. UNINTERRUpTIBLE Power SuPPly GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES

Transcription

1 UPS UNINTERRUpTIBLE Power SuPPly GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES

2 Index General characteristics page 4 Modular page 12 Conventional page 32 Line-interactive page 44 Communication accessories page 50 Services page 56 INDEX 3

3 VDI STRUCTURED CABLING ELECTRICAL protection LIGhTING MANAGEMENT hospital SIGNALLING ENERGy MANAGEMENT 4

4 ServICe SeCtor An offer that IS ConStAntly evolving MEASUREMENT SySTEMS ENERGy DISTRIBUTION UPS UnInTErrUPTIBLE POwEr SUPPLy SUpERVISION OF INSTALLATIONS FIRE ALARM SySTEMS The guarantee of optimum Continuity of service Legrand, world leader in the manufacture of electrical equipment, offers an extensive range of solutions to meet all the needs of service sector installations, from structured cabling systems for data networks through to control and management of the installation, including trunking and distribution systems. Incorporating an environmentally-friendly approach to technological development and to address a constantly changing market, Legrand is now offering its new range of UPS and additional functions to ensure maximum continuity of service for all installations. GENERAL ChARACTERISTICS 5

5 6 energy efficiency and economy

6 Maximum energy quality High efficiency The innovative design and high quality of the components used enable our UPS to achieve up to 95% efficiency, leading to significant energy savings. Advanced technology The On-line Double Conversion technology ensures provision of a top quality power supply and maximum energy efficiency Environmentally responsible approach Our UPS are built with the greatest care with a view to sustainable development. Moreover, Legrand has developed an innovative testing system which reduces the energy consumed for each device manufactured. GENERAL ChARACTERISTICS 7

7 8

8 reliability and safety technological excellence applied to reliable electronics The optimum sizing of the power stages and thorough testing of each unit ensure excellent reliability. Latest generation components A careful search for the best electronic components on the market, together with the most up-to-date manufacturing methods, ensure that Legrand UPS use leading-edge technology and provide optimum reliability. High performance batteries The batteries used in Legrand UPS are the best on the market. The innovative charging system significantly extends battery life by up to 50%. GENERAL ChARACTERISTICS 9

9 the range p12 ModulAr p32 ConventIonAl UPS up to 120 kva providing maximum safety (power and control), for applications requiring easy expansion and fast maintenance. UPS providing a safe, reliable power supply up to 10 kva. 10

10 The right solution for every context Legrand has a UPS range that it divided into 3 different families. It is an offer suitable for all applications with solutions providing the best performance levels in terms of power and backup time. Legrand UPS are ideal for all your requirements. p44 line InterACtIve p50 CoMMunICAtIon ACCeSSorIeS UPS up to 3 kva. Ideal protection for individual workstations, telephone switchboards or home automation applications and even for small service sector companies. A complete range of communication devices for managing, configuring and controlling the UPS remotely. GENERAL ChARACTERISTICS 11

11 12

12 ModulAr MEGALInE TrIMOD ArCHIMOD Flexible, expandable, redundant solutions Modular UPS enable the power supply to be sized exactly to requirements, without precluding any future expansion. They are made up of standard modules that can be added to existing configurations to increase their power or backup time. Their innovative three-phase system, made up of individual single phase modules, provides the highest possible level of redundancy. MODULAR UpS 13

13 ArChIMod And trimod dynamic three-phase SySteMS UPS offering optimum adaptability for all types of installation with their exclusive technology. The innovative modular design of these UPS means that the availability of the power can be optimised, the flexibility of the system increased and the total cost of ownership (TCO) reduced. Highly standardised components, consisting of individual single phase modules, provide the most flexible expandability on the market. 14

14 Product Differentiation Excellence Award 2011 Gradual power adaptation The three-phase UPS are made up of individual single phase modules which are redundant and "selfconfiguring", so that power can be increased quickly and safely. Optimisation of work The compact and lightweight power modules (only 8.5 kg) make the UPS easy to transport, install and maintain. flexibility ModulArIty expansion ArChIMod And trimod MODULAR UpS 15

15 ArChIMod And trimod exclusive ChArACterIStICS Expanding the power The power can be increased very quickly and easily inside the cabinet itself for both product families, without the need to reconfigure the installation or the UPS. TrIMOD from 10 to 60 kva ArCHIMOD from 20 to120 kva Extending the backup time The backup time can be extended either by adding battery trays in the same cabinet or by adding another battery cabinet, depending on the power of the UPS and the backup time required. Non-modular compact battery cabinets are also available for extending the backup time to several hours. 16

16 redundancy on the single phase load R S T R S T In a three-phase power supply system with single phase loads, if one of the modules fails, there is no loss of power as the power is distributed over the other modules that are still operational. LOAD not OK LOAD redundancy on the phases R S T R S T In a system with three-phase outputs, it is possible to create redundancy on each individual phase. If one of the power modules fails, the other modules for this phase take over from the faulty module. L1 L2 L3 not OK L1 L2 L3 redundancy on the control R S T R S T In UPS that include several control modules, the failure of one of the control modules results in the modules it controls being stopped. However continuity of service is assured by the automatic distribution of the lost power over the other modules. not OK R S T R S T three-phase ModulAr Maximum redundancy levels The innovative design of the modular UPS enables different levels of redundancy to be obtained so that maximum continuity of service is maintained at all times. MODULAR UpS 17

17 Efficiency up to 95% when operating in ON LINE MODE ArChIMod three-phase ModulAr Plug-in modules with self-configuring Plug&Play system Power factor at the input close to 1 at 20% load Multiple I/O to obtain different three-phase/ single phase configurations as required ARCHIMOD: expandable, modular architecture UPS, power from 20 to 120 kva, in a 19" rack cabinet. The system comprises a set of standard, pre-assembled components which simplify and optimise the design and building of infrastructures. 18

18 MODULAR ARChITECTURE 6 1 Control module Equipped with a microprocessor, it manages 3 power modules. If it is used with a power expansion module, it can manage up to 6 power modules, thus increasing the power from 20 to 40 kva. It has a screen and a multifunction keypad for monitoring the operating parameters of the UPS and for configuring numerous functions. It can be connected in parallel to other control modules and used with power expansion modules. The front panel has a backlit status indicator for immediate checking of the operating status of the system and an RS 232 port for connecting a PC for maintenance. 1 2 Power modules The power modules (nominal power 6.7 kva) are extremely compact and easy to handle. They have a plug-in hot swap system, making them quick to install and maintain. They work in parallel with all modules that are present to ensure optimum system performance. 3 Power expansion module This must be used with a control module. It increases the power from 20 to 40 kva and can be used to establish individual redundancy on each phase. 4 Battery modules Each module contains batteries that can be connected in series, forming separate strings. The compactness and functionality of the single (plug-in) module make it easy to handle, and expansion operations are possible without any modification of the structure of the installed system. 5 Distribution module This is used to configure the distribution type of the UPS (three-phase/three-phase, three-phase/single phase, single phase/single phase or single phase/ three-phase). It has I/O connection blocks, handling and protection devices, and the connection for additional battery cabinets. The power supply can be configured on two separate input sources (main and backup) Cable entry Special sleeves enable entry and exit of the input and output cables, via the top and via the bottom MODULAR UpS 19

19 trimod three-phase ModulAr Space-saving modular and expandable with powers from 10 to 60 kva in a compact structure. The totally modular design of TRIMOD UPS enables each power module to be programmed to obtain the required I/O configuration. It is possible to have three-phase or single phase voltage inputs and outputs to obtain one of the following configurations: three-phase/three-phase, three-phase/single phase, single phase/three-phase or single phase/single phase. It is also possible to have single phase and three-phase output lines simultaneously, or several single phase of different powers (optional). Control screen The TRIMOD system is totally controlled by a microprocessor. Using the LCD screen and the keypad, it is possible to: - Set and view the operating data in real time - Configure and control the parameters of each power module - Access the event logs - Perform a series of functional tests Compact, space-saving versions The compact size, low vertical structure and the 2 small wheels at the back make it easy to position and transport the UPS, even in locations that are difficult to access. 20

20 Redundant modular UPS, expandable up to 10 kva with the best performance levels in their category MeGAlIne SInGle PhASe ModulAr AVAILABLE IN ThREE VERSIONS: - SINGLE CABINET - DOUBLE CABINET - 19" RACK" All models have a configurable microprocessor control card, an LCD display unit, 1250 VA power modules and battery kits (BK) containing three 9 Ah batteries. The single cabinet and 19" rack versions distribute powers of 1250 to 5000 VA, and can take up to 4 power modules 4 battery kits. To increase the backup time, additional batteries can be added in dedicated cabinets, which are easy to connect. The range also includes double cabinets. They consist of 2 cabinets: 1 power cabinet and 1 battery cabinet. The former houses up to eight 1250 VA modules, reaching a maximum power of 10 kva. The latter can take up to 10 battery kits and an additional charger. To increase the backup time still further, other identical battery cabinets can be added. MODULAR UpS 21

21 ArChIMod Double conversion VFI three-phase modular UPS Configurations 20 Power: 20 kva Backup time: 65 min 1 Cabinet 1 Control module 3 Power modules 30 Battery modules 1 Distribution module 40 Power: 40 kva Backup time: 21 min 1 Cabinet 2 Control modules 6 Power modules 24 Battery modules 1 Distribution module Pack Cat. Nos. Configurable Cabinets The cabinets are supplied empty and are preset for the power and capacity indicated in the table NomiNal power (kva) Number of battery modules Number of control modules No. of power expansion modules Number of phases * / / / * Capacity of cabinet: 18 U Power: 60 kva Backup time: 8 min 1 Cabinet 3 Control modules 9 Power modules 18 Battery modules 1 Distribution module 80 Power: 80 kva Backup time: 14 min 2 Cabinets 3 Control modules 1 Power expansion module 12 Power modules 36 Battery modules 1 Distribution module additional Cabinets for batteries description Empty modular battery cabinet Battery cabinet for 20 kva UPS with 21 x 94 Ah long life batteries Battery cabinet for kva UPS with 21 x 94 Ah long life batteries Battery cabinet for 80 kva UPS with 21 x 94 Ah long life batteries Battery cabinet for kva UPS with 21 x 94 Ah long life batteries Cover for empty battery slot Cover for empty power module slot 100 Power: 100 kva Backup time: 10 min 2 Cabinets 3 Control modules 2 Power expansion modules 15 Power modules 36 Battery modules 1 Distribution module 120 Power: 120 kva Backup time: 8 min 2 Cabinets 3 Control modules 3 Power expansion modules 18 Power modules 36 Battery modules 1 Distribution module accessories description kva power module Front/rear door Kit of 3 x 9 Ah battery trays Kit of 3 empty battery trays note: The backup times, expressed in minutes, are measured under optimum operating conditions. 22

22 ArChIMod Double conversion VFI three-phase modular UPS Cat. nos. General characteristics Input characteristics output characteristics Batteries Nominal power (kva) Active power (kw) Module power (kva) 6.7 per power module (20 kva with 3 modules), cos φ 0.9 Technology System Hot Swap capacity On-line double conversion VFI-SS-111 Modular, expandable and redundant system in a single cabinet, 19" rack The power and/or battery modules can be replaced without switching off the UPS Input voltage 230 V 1P+N, 400 V 3P+N 400 V 3p+N Input frequency Input voltage range 230 V + 15%/-20% 1P 400 V + 15 %/-20% 3P Hz ± 2% autosensing THD of input current 3% Compatibility with gensets Input power factor 400 V +15%/-20% 3P Configurable for synchronisation between the input and output frequencies, even for the highest frequency ranges, ± 14% 0.99 at 20% load Output voltage 230 V 1P, 400 V 3P 400 V 3p Efficiency at full load Up to 95% Nominal output frequency 50/60 Hz ± 0.1 Peak factor 3.5:1 Tolerance on output voltage ±1% Permitted overload 10 minutes at 125% and 60 seconds at 150% Efficiency in Eco mode 99% Bypass Battery modules Battery range type/voltage Automatic and maintenance bypass The battery modules are designed for easy insertion in the cabinet. No special operation is required to connect them VRLA - AGM/252 VDC Communication and management Backup time Battery charging Screen and signalling Configurable and extendable, both internally and with additional battery cabinets Smart Charge technology 3-step advanced cycle 4 x 20-character lines, 4 menu navigation buttons, multi-coloured LED status indicator Physical characteristics Ambient conditions Conformity Services Communication ports Back-feed protection Emergency stop Remote control For each control module: 2 x RS232 serial ports, 1 logic level port, 5 volt-free contact ports, 2 slots for SNMP interfaces (optional) N/C + N/O auxiliary contact yes Available Dimensions (H x W x D) (mm) 2080 x 570 x 912 (42 U) Installed power modules Installable battery modules Up to 30 Up to 24 Up to Net weight (kg) Operating temperature/humidity 0-40 C/20-80% Protection index Ip 21 Maximum noise audible at 1 m (dba) 50 to 65 Heat dissipation (BTU/h) Certifications EN , EN , EN Installation Maintenance Can be carried out by the user, modular architecture with plug and play power modules and batteries for easy installation and configuration Can be carried out by the user, optional services available from the manufacturer MODULAR UpS 23

23 trimod Double conversion VFI three-phase modular UPS Pack Cat. Nos. Power Cabinet NomiNal power kva active power backup time kw (min) Number of cabinets weight (kg) ' ' ' ' ' ' Pack Cat. Nos. ups NomiNal power (kva) backup time (min) Number of cabinets weight (kg) * * * x * x * x x x 3, * x 3, * x x * x x 3, * x 3, * x 3, * * Configurations with battery cabinet (20 x 94 Ah). Battery cabinet dimensions and weight: H x W x D 1635 x 600 x 800 (mm), 785 kg Power Cabinet (empty) No. of power No. of battery modules modules type of power module No. of phases x 3.4 kva 1-1/3-3/3-1/ x 5 or 6.7 kva 1-1/3-3/3-1/ x 5 kva x 5 kva 1-1/3-3/3-1/ x 6.7 kva x 6.7 kva 3-3 accessories description kva power module kva power module kva power module Additional charger module for 5 kva extensions accessories for batteries description Kit of 4 empty battery trays Single battery tray with 5 x 7.2 Ah batteries (can be installed in multiples of 4) Single battery tray with 5 x 9 Ah batteries (can be installed in multiples of 4) additional battery Cabinets description Modular battery cabinet (empty) with 16 trays Modular battery cabinet (empty) with 20 trays Modular battery cabinet with 4 battery trays (7.2 Ah) Modular battery cabinet with 8 battery trays (7.2 Ah) Modular battery cabinet with 12 battery trays (7.2 Ah) Modular battery cabinet with 16 battery trays (7.2 Ah) Modular battery cabinet with 20 battery trays (7.2 Ah) Modular battery cabinet with 4 battery trays (9 Ah) Modular battery cabinet with 8 battery trays (9 Ah) Modular battery cabinet with 12 battery trays (9 Ah) Modular battery cabinet with 16 battery trays (9 Ah) Modular battery cabinet with 20 battery trays (9 Ah) Battery cabinet for 10 kva UPS with 20 x 94 Ah long life batteries Battery cabinet for 20 kva UPS with 20 x 94 Ah long life batteries Battery cabinet for 30 kva UPS with 20 x 94 Ah long life batteries Battery cabinet for 40 kva UPS with 20 x 94 Ah long life batteries Battery cabinet for 60 kva UPS with 20 x 94 Ah long life batteries 24 note: The backup times, expressed in minutes, are measured under optimum operating conditions.

24 trimod Double conversion VFI three-phase modular UPS Cat. nos General characteristics Input characteristics output characteristics Batteries Communication and management Physical characteristics Ambient conditions Conformity Services Nominal power (kva) Active power (kw) Module power (kva) Technology System On-line double conversion VFI-SS-111 Modular, expandable and redundant in a single cabinet/expandable and redundant modular system Input voltage 230 V 1P+N, 400 V 3P+N 400 V 3p+N Input frequency Hz ± 2% autosensing Input voltage range 400 V +15%/-20% V +15%/-20% 400 V +15%/-20% THD of input current 3% Compatibility with gensets Input power factor Configurable for synchronism between the input and output frequencies, even for the highest frequency ranges, ± 14% 0.99 at 20% load Output voltage 230 V 1P+N, 400 V 3P +N 400 V 3p + N Efficiency at full load Up to 95% Nominal output frequency 50/60 Hz can be selected by the user ±1 Hz Peak factor 3.5:1 Tolerance on output voltage ± 1% Permitted overload 10 minutes at 125% and 60 seconds at 150% Efficiency in Eco mode 98% Bypass Battery module Battery range type/voltage Backup time Battery charging Screen and signalling Communication ports Back-feed protection Emergency stop Remote control Automatic and maintenance bypass The battery modules are designed for easy insertion in the cabinet. No special operation is required to connect them VRLA - AGM/240 VDC (internal redundant range) Configurable and extendable, both internally and with additional battery cabinets Smart Charge technology 3-step advanced cycle 4 x 20-character lines, 4 menu navigation buttons, multi-coloured LED status indicator, alarms and audible signalling 2 x RS232 serial ports, 1 logic level port, 4 volt-free contact ports, 1 slot for interfaces N/C + N/O auxiliary contact yes Available Dimensions (H x W x D) (mm) 1370 x 414 x 628 Installed power modules Installable battery modules Up to Net weight (kg) Operating temperature/humidity 0-40 C/20-80% Protection index Ip 21 Maximum noise audible at 1 m (dba) 46 Heat dissipation (BTU/h) Certifications EN , EN , EN Installation Maintenance Easy management Can be carried out by the user, modular architecture with plug and play power modules and batteries Can be carried out by the user, optional services available from the manufacturer Advanced diagnostic functions on the screen MODULAR UpS 25

25 MeGAlIne Double conversion VFI single phase modular UPS Pack Cat. Nos. single Cabinet - without batteries NomiNal power (Va) active power (w) backup time (min) Number of cabinets double Cabinet - without batteries NomiNal power (Va) active power (w) backup time (min) Number of cabinets Pack Cat. Nos. single Cabinet (german standard) NomiNal power (Va) active power backup time (w) (min) Number of cabinets weight (kg) double Cabinet NomiNal power (Va) active power backup time (w) (min) Number of cabinets weight (kg) single Cabinet (french standard) NomiNal power (Va) active power (w) backup time (min) Number of cabinets weight (kg) single Cabinet (british standard) NomiNal power (Va) active power (w) backup time (min) Number of cabinets weight (kg) battery extensions description Cabinet with 1 BK Cabinet with 2 BK Cabinet with 3 BK Cabinet with 4 BK Cabinet with 5 BK Cabinet with 6 BK Cabinet with 7 BK Cabinet with 8 BK Cabinet with 9 BK Cabinet with 10 BK battery extensions with Charger description Cabinet with 1 BK with charger Cabinet with 2 BK with charger Cabinet with 3 BK with charger Cabinet with 4 BK with charger Cabinet with 5 BK with charger Cabinet with 6 BK with charger Cabinet with 7 BK with charger Cabinet with 8 BK with charger Cabinet with 9 BK with charger Cabinet with 10 BK with charger accessories description Power module (PW 1250) Single cabinet backup extension (MegaLine BK/1) Double cabinet backup extension (MegaLine BK/2) Empty battery cabinet Y cable for connecting a second additional battery cabinet Battery cabinet extension kit for tower configuration (PL MegaLine cable) Manual bypass for single cabinet (BP/1) Manual bypass for double cabinet (BP/2) Additional charger (CB 36) Relay interface kit note: The backup times, expressed in minutes, are measured under optimum operating conditions. 26

26 MeGAlIne Double conversion VFI single phase modular UPS Cat. nos SInGle CABInet double CABInet General characteristics Nominal power (VA) Active power (W) Max. expansion (VA) Max. expansion (W) Technology On-line double conversion VFI-SS-111 Architecture Modular, expandable, N+X redundant with 1250 VA power cards, contained in a single cabinet Input characteristics Nominal input voltage 230 V Input voltage range 184 V to 264 V at 100% load Minimum operating voltage 100 V at 50% load THD of input current 3% Input power factor 0.99 at 20% load Input frequency 50 Hz/60 Hz ± 2% autosensing output characteristics Output voltage 230 V ± 1% Output frequency 50 Hz/60 Hz synchronised THD of output voltage 1% with non-linear load Waveform Sinusoidal Peak factor 3.5:1 Efficiency 92% at 100% load Permitted overload 300% for 1 s 200% for 5 s 150% for 30 s Backup time Backup time (min) 13 Extension of backup time yes equipment Bypass Automatic, internally synchronised, static and electromechanical (for overloads and operating problems) Signalling and alarms Wide screen with 4 alphanumeric lines, multi-coloured status indicator, audible signalling Communication ports 1 RS 232 port, 2 logic level ports Communicator UPS software Can be downloaded free of charge (after requesting an activation code) Electronic devices for protection against overloads, short-circuits and excessive battery discharge. Operation stops at end of backup time. Inrush current limiter on start-up. Protection Sensor for correct neutral switching. Back-feed protection (electrical safety insulation of the input plug during battery-based operation). EPO (emergency power off) contact I/O mains connection German standard/terminal connector with universal multi-socket outlet (Italian/German standard) Mechanical characteristics Net weight (kg) Dimensions (H x W x D) (mm) 475 x 270 x x 475 x 270 x 570 Installed power cards Free power expansion slots Installed battery kits Free backup time extension slots Ambient conditions Ambient operating temperature ( C) 0 to 40 Certifications Protection index Ip 21 Relative humidity (%) 20 to 80 Noise at 1 m (dba) 40 Reference product standards EN , EN , EN MODULAR UpS 27

27 MeGAlIne rack Double conversion VFI single phase modular UPS Wide input voltage and frequency range - Operating frequency: 50 or 60 Hz with auto-recognition Hz frequency conversion in both directions - Extension of the input frequency range for operation with gensets - Eco mode (energy-saving) operation - Load waiting mode operation (protection on request) - Output voltage can be adjusted in 1 volt steps from front panel - Low noise - Internal and external temperature measurement - Ventilation control according to temperature and load - Designed for remote emergency stop Pack Cat. Nos. racks (german standard) NomiNal power (Va) active power backup time (w) (min) Number of cabinets weight (kg) racks (french standard) NomiNal power (Va) active power backup time (w) (min) Number of cabinets weight (kg) racks (british standard) NomiNal power (Va) active power backup time (w) (min) Number of cabinets weight (kg) Pack Cat. Nos. backup time extensions NomiNal power (Va) additional bk expansion (min) battery expansions for rack ups description Rack with 1 BK Rack with 2 BK Rack with 3 BK Rack with 4 BK Rack with 1 BK with charger Rack with 2 BK with charger Rack with 3 BK with charger Rack with 4 BK with charger accessories description Power module (PW 1250) Empty battery rack cabinet Manual bypass for single rack (BP/1) Additional charger (CB 36) Relay interface kit Telescopic runner kit for 6U rack note: The backup times, expressed in minutes, are measured under optimum operating conditions. 28

28 MeGAlIne rack Double conversion VFI single phase modular UPS Cat. nos. General characteristics Input characteristics output characteristics Backup time equipment Nominal power (VA) Active power (W) Max. expansion (VA) 5000 Max. expansion (W) 3500 Technology Architecture Nominal input voltage Input voltage range Minimum operating voltage via mains On-line double conversion VFI-SS-111 Modular, expandable, N+X redundant with 1250 VA power cards, contained in a single rack 230 V 184 V to 264 V at 100% load 100 V at 50% load THD of input current 3% Input power factor Input frequency 0.99 at 20% load 50 Hz/60 Hz ± 2% autosensing Output voltage 230 V ± 1% Output frequency THD of output voltage Waveform 50 Hz/60 Hz synchronised 1% with non-linear load Sinusoidal Peak factor 3.5:1 Efficiency via mains Permitted overload 92% at 100% load 300% for 1 s 200% for 5 s 150% for 30 s Backup time (min) 13 Extension of backup time Bypass Signalling and alarms Communication ports Communicator UPS software yes Automatic, internally synchronised, static and electromechanical (for overloads and operating problems). Large screen with 4 alphanumeric lines, multi-coloured status indicator, audible signalling 1 RS 232 port, 2 logic level ports Can be downloaded free of charge (after requesting an activation code) Protection Electronic devices for protection against overloads, short-circuits and excessive battery discharge. Operation stops at end of backup time. Inrush current limiter on start-up. Sensor for correct neutral switching. Back-feed protection (electrical safety insulation of the input plug during battery-based operation). EPO (emergency power off) contact Mechanical characteristics Ambient conditions Certifications I/O mains connection German standard/terminal connector with universal multi-socket outlet (Italian/German standard) Net weight (kg) Dimensions (H x W x D) (mm) 266 x 483 x 582 Installed power cards Free power expansion slots Installed battery kits Free backup time extension slots Ambient operating temperature ( C) 0 to 40 Protection index Ip 21 Relative humidity (%) 20 to 80 Noise at 1 m (dba) 40 Reference product standards EN , EN , EN MODULAR UpS 29

29 MeGAlIne Backup times for single cabinet and double cabinet versions Model Power Backup time Single cabinet double cabinet number of cabinets and dimensions w x h x d (mm) Cat. nos VA 30 1x (270 x 475 x 570) VA 52 1x (270 x 475 x 570) VA 75 1x (270 x 475 x 570) VA 22 1x (270 x 475 x 570) VA 30 2x (270 x 475 x 570) VA 52 2x (270 x 475 x 570) VA 63 2x (270 x 475 x 570) VA 18 1x (270 x 475 x 570) VA 29 2x (270 x 475 x 570) VA 44 2x (270 x 475 x 570) VA 67 2x (270 x 475 x 570) VA 22 2x (270 x 475 x 570) VA 30 2x (270 x 475 x 570) VA 46 2x (270 x 475 x 570) VA 63 2x (270 x 475 x 570) VA 22 2x (270 x 475 x 570) VA 30 2x (270 x 475 x 570) VA 46 3x (270 x 475 x 570)* VA 63 3x (270 x 475 x 570)* VA 20 2x (270 x 475 x 570) VA 30 2x (270 x 475 x 570) VA 47 3x (270 x 475 x 570)* VA 60 3x (270 x 475 x 570)* VA 18 2x (270 x 475 x 570) VA 30 3x (270 x 475 x 570)* VA 48 3x (270 x 475 x 570)* VA 59 3x (270 x 475 x 570)* (x2) 8750 VA 20 2x (270 x 475 x 570) VA 30 3x (270 x 475 x 570)* VA 45 3x (270 x 475 x 570)* VA 61 4x (270 x 475 x 570)* (x2) VA 22 3x (270 x 475 x 570)* VA 30 3x (270 x 475 x 570)* VA 46 4x (270 x 475 x 570)* (x2) VA 60 4x (270 x 475 x 570)* (x2) * This configuration requires the use of a Y cable Cat. No The number of cables required is equal to the total number of cabinets minus 2. note: The backup times, expressed in minutes, are measured under optimum operating conditions. 1 cabinet w 270 mm 2 cabinets w 540 mm 3 cabinets w 810 mm 4 cabinets w 1080 mm 5 cabinets w 1350 mm 30

30 MeGAlIne rack Backup times Model Power Backup time racks number of racks and dimensions w x h x d (mm) Cat. nos VA 30 1 (6U) VA 52 1 (6U) VA 75 1 (6U) VA 22 1 (6U) VA 30 1 (6U) VA 52 2 (6U + 3U) VA 63 3 (6U + 2x3U) VA 18 1 (6U) VA 29 2 (6U + 3U) VA 44 3 (6U + 2x3U) VA 67 3 (6U + 3x3U) (x2) 5000 VA 22 2 (6U + 3U) VA 30 2 (6U + 2x3U) VA 46 3 (6U + 3x3U) VA 63 4 (6U + 4x3U) (x2) note: The backup times, expressed in minutes, are measured under optimum operating conditions. 6U= 483 x 266 x 582 3U= 483 x 133x rack h 266 mm (6u) 2 racks h 532 mm (9u) 3 racks h 798 mm (12u) 4 racks h 1064 mm (15u) 5 racks h 1330 mm (18u) MODULAR UpS 31

31 32

32 ConventIonAl Daker DK whad DHEA Safe, efficient, innovative solutions On-line double conversion UPS with DSP microprocessors for precise, constant control of all measurements and of the power factor correction circuit (PFC). Professional solutions with power up to 10 kva. Transformer-free technology for high quality energy output with up to 93% efficiency. CONVENTIONAL UpS 33

33 On-Line double conversion UPS that can be used in both tower and rack configurations daker dk ConventIonAl SInGle PhASe The main parameters of the system and the status of the UPS, including the battery charge level and faults, are displayed on the LCD screen. Additional battery cabinets are available to increase the backup time of the UPS. A charger can be added in all battery cabinets for fast, safe charging. Tower version with additional battery cabinet 34

34 Three standard sizes for power up to 10 kva The UPS and additional battery cabinets are available in sizes ranging from 2 to 4 units, depending on the required power and backup time. UPS and 2-unit battery cabinet UPS and 3-unit battery cabinet UPS and 4-unit battery cabinet reversible screen With the reversible screen, the Daker DK UPS can be used in both tower and 19" rack configuration. CONVENTIONAL UpS 35

35 On-Line double conversion UPS for low and medium power applications whad ConventIonAl SInGle PhASe The distributed power, from 800 VA to VA, provides high level electrical protection for medium power devices. The UPS comprise a single card with incorporates power, control logic, control and diagnostics. With their compact size and slender, narrow shape, WHAD UPS take up very little space, even if they are located at a work station. Models up to 2500 VA have a backup time that can be extended by adding battery cabinets. The highest performance versions have a special connector for connecting SNMP communication interfaces. 36

36 On-Line double conversion UPS that can be extended with stackable, automaticconnection units dhea energy StAtIon ConventIonAl SInGle PhASe The system comprises a UPS unit and battery packs with automatic connections and a hot-swap system. The compact size (depth: 185 mm) enables the UPS to be installed in very small spaces. The special sealed, fume-free batteries enable it to be used in the home. Load management The 1500 VA model has 3 outputs, 2 of which are timed, deactivating themselves after a pre-set time, thus extending the supply to the most important loads according to the available backup time. Plug-in connection with hot-swap system The standard units with automatic connections make it very easy for inexperienced users to install all the system's components. With the hot-swap system, battery packs can be added or replaced at any time, without switching off the UPS. CONVENTIONAL UpS 37

37 daker dk Conventional UPS - Single phase On-line double conversion VFI The main parameters of the UPS, including the battery charge level and faults, are displayed on the LCD screen on the front panel. The integrated communication software not only controls the UPS and its switch-off if there is a malfunction, and enables the user to test the main functions remotely, communicate via SNMP/Internet/network adaptor and access the functions of the UPS via the Internet, but can also send the user an SMS if specific events occur. The internal extension connector enables a WEB/SNMP card or a relay interface to be installed which provides insulated contacts for applications on industrial control panels or remote alarm panels. If there is an electronic fault, overload, overheating or for scheduled maintenance operations, the automatic or manual (optional) bypass ensures continuity of the power supply for critical loads. A bypass switch is available for maintenance. Pack Cat. Nos. Convertible ups with batteries NomiNal power (Va) active power (w) backup time (min) weight (kg) Pack Cat. Nos. miscellaneous accessories description Additional 200 W charger (for Daker DK ) Additional 1000 W charger (for Daker DK ) Rack support bracket kit External manual bypass (for Daker DK ) Volt-free contact card Convertible ups without batteries NomiNal power (Va) active power (w) backup time (min) weight (kg) battery Cabinet (with batteries) description Battery cabinet for (12 x 12 V, 7.2 Ah batteries) Battery cabinet for (12 x 12 V, 7.2 Ah batteries) Battery cabinet for (12 x 12 V, 9 Ah batteries) Battery cabinet for and (20 x 12 V, 7.2 Ah batteries) Battery cabinet for (20 x 12 V, 9 Ah batteries) battery Cabinet (empty) description Battery cabinet for (for 12 x 12 V, 7.2 Ah batteries) Battery cabinet for (for 12 x 12 V, 7.2 Ah batteries) Battery cabinet for (for 12 x 12 V, 9 Ah batteries) Battery cabinet for and (for 20 x 12 V, 7.2 Ah batteries) Battery cabinet for (for 20 x 12 V, 9 Ah batteries) note: The backup times, expressed in minutes, are measured under optimum operating conditions. 38

38 daker dk Conventional UPS - Single phase On-line double conversion VFI Cat. nos General characteristics Input characteristics output characteristics Batteries Communication and management Mechanical characteristics Ambient conditions Certifications Nominal power (VA) Active power (W) Technology Waveform Architecture Input voltage Input frequency Input voltage range On-line double conversion VFI-SS-111 Sinusoidal Convertible tower and 19" rack 230 V Hz ± 5% autosensing 160 V V full load THD of input current 3% Input power factor 0.99 Compatibility with gensets Configurable for synchronism between the input and output frequencies, even for the highest frequency ranges, ± 14% Output voltage 230 V ± 1% Output frequency (nominal) 50/60 Hz (configurable via LCD panel) +/- 0.1% Peak factor 1:3 THD of output voltage 3% with linear load Output voltage tolerance ± 1% Bypass Backup time extension Automatic bypass and optional external manual bypass Number of batteries Battery range type/voltage 12 V 7.2 Ah 12 V 7.2 Ah 12 V 9 Ah 12 V 5 Ah - 12 V 5 Ah - - Backup time (min) Screen and signalling yes Four buttons and four LEDs for real-time control of the status and the main parameters of the UPS Communication ports RS232 and USB serial ports RS232 serial ports Remote control Connector for network interface Dimensions (H x W x D) (mm) Dimensions of battery cabinet H x W x D (mm) 440x88 (2U) x x176 (4U) x x88 (2U) x x88 (2U) x x88 (2U) x x88 (2U) x x176 (4U) x680 - Available SNMp 440x88 (2U) x x132 (3U) x x176 (4U) x x88 (2U) x x132 (3U) x x132 (3U) x x132 (3U) x680 Net weight (kg) * 52 25* 26* Operating temperature ( C) 0 40 C Protection index Ip 21 Relative humidity (%) 20 to 80% Noise at 1 m (dba) 50 Heat dissipation (BTU/h) Reference product standards EN , EN , EN * weight without batteries note: The backup times, expressed in minutes, are measured under optimum operating conditions. CONVENTIONAL UpS 39

39 daker dk Long backup time table Model Power Backup time dimensions and number of cabinets h x w x d (mm) Cat. nos x 88 x h x 88 x x176 x VA 2h x 88 x x176 x 405 (x2) (x2) 4h x 88 x x176 x 405 (x3) (x3) 5h x 88 x x 176 x 405 (x4) (x4) x 88 x x 88 x 650 (x2) VA 1h x 88 x 650 (x3) (x2) 1h x 88 x 650 (x4) (x3) 2h x 88 x 650 (x5) (x4) x 88 x x 88 x 650 (x2) VA 1h x 88 x 650 (x3) (x2) Daker DK 1h x 88 x 650 (x4) (x3) 2h x 88 x 650 (x5) (x4) x 88 x x 132 x VA x 88 x x 132 x 680 (x2) (x2) x 88 x x 132 x 680 (x3) (x3) 1h x 88 x x 132 x 680 (x4) (x4) x 88 x x 132 x VA 29' 440 x 88 x x 132 x 680 (x2) (x2) 49' 440 x 88 x x 132 x 680 (x3) (x3) 1h x 88 x x132x680 (x4) (x4) x 132 x x 132 x x132x x 132 x 680 (x2) (x2) VA x132x x 132 x 680 (x3) (x3) x 132 x x 132 x 680 (x4) (x4) x 132 x x 132 x 680 (x5) (x5) note: The backup times, expressed in minutes, are measured under optimum operating conditions va 2 cabinets w 2u + 4u 3000 va 3 cabinets w 2u +2 u + 2u 6000 va 2 cabinets w 2u + 3u va 2 cabinets w 3u + 3u TOWER version 1000 va 2 cabinets h 6u (264 mm) 4500 va 3 cabinets h 6u (264 mm) 6000 va 2 cabinets 5u (320 mm) va 2 cabinets h 6u (264 mm) RACK version 40

40 dhea Conventional UPS - Single phase On-line double conversion VFI Cat. nos General characteristics Nominal power (VA) Active power (W) Technology On-line double conversion Waveform Sinusoidal Nominal input voltage Input voltage range Minimum mains operating voltage Input frequency Input power factor 230 V 184 V 265 V at 100% load 184 V with nominal load/100 V at 50% of nominal load 50/60 Hz ± 2% (± 14% in extended range) 0.99 at 20% load Output voltage 230 V ± 1% Output voltage distortion 1% System can be combined with a genset to increase the backup time if there are prolonged faults. - Battery packs with integrated batteries and automatic connectors. - Up to 10 battery packs can be added. - UPS supply voltage only present when the pack is connected. Pack Cat. Nos. energy stations NomiNal power Va active power w batteries description Battery pack Output frequency (battery operation) Batteries 50/60 Hz ± 1% 2 x 36 V 7.2 Ah stacking battery packs Acoustic noise at 1 m (dba) 40 Net weight (kg) 4 (UPS) + 16 (battery pack) Dimensions (H x W x D) (mm) 309 x 450 x 170 (UPS) x 450 x 170 (battery pack) Regulations EN , EN , EN External connections 1 x RS contact outputs (2 poles) + EPO Protection index Ip 21 Output sockets 1 line 3 lines (2 of which are timed) no. of battery Backup time packs 1000 va 1500 va h h 16 1h h 16 1h h 8 2h h 4 3h h 46 3h h 55 4h h 8 5h h 7 5h 36 note: The backup times, expressed in minutes, are measured under optimum operating conditions. CONVENTIONAL UpS 41

41 whad Conventional UPS - Single phase On-line double conversion VFI All models have: - Logic level port which can be connected to a relay interface kit (except for Cat. Nos , and ). - Slot for connecting internal versions of SNMP, CS121 SK and CS121B SK communication interfaces (for 3, 4, 5 and 6 kva). - An external maintenance bypass device can be connected, which is designed to be connected to the I/O connector on the back of the UPS (for 3, 4, 5 and 6 kva). Pack Cat. Nos. ups with german standard sockets NomiNal power (Va) active power (w) backup time (min) weight (kg) ups with french standard sockets NomiNal power (Va) active power (w) backup time (min) weight (kg) ups with british standard sockets NomiNal power (Va) active power (w) backup time (min) weight (kg) Model WhAD Power 800 VA 1000 VA 1500 VA 2000 VA 2500 VA Backup time 1h 40 3h 5 1h 15 1h h h h 7 dimensions and no. of cabinets h x w x d (mm) 88 x 355 x x 319 x x 355 x x 319 x 390 (x2) 88 x 355 x x 319 x x 355 x x 319 x 390 (x2) 88 x 355 x x 319 x x 355 x x 319 x 390 (x2) 460 x 160 x x 319 x x 160 x x(160 x 319 x 390) 460 x 160 x x 319 x x 160 x x(160 x 319 x 390) Cat. nos (x2)* (x2)* (x2)* , (x2)* , (x2)* * This configuration requires the use of a Y cable Cat. No The number of cables required is equal to the total number of cabinets minus 1. miscellaneous accessories description Additional battery cabinet for Additional battery cabinet for Y cable for connecting two battery cabinets Manual bypass for 3000 VA/4000 VA UPS Manual bypass for 5000 VA/6000 VA UPS Relay interface kit note: The backup times, expressed in minutes, are measured under optimum operating conditions. 42

42 whad Conventional UPS - Single phase On-line double conversion VFI Cat. nos. General characteristics Input characteristics output characteristics Batteries Communication and management Mechanical characteristics Ambient conditions Certifications Nominal power (VA) Active power (W) Technology Waveform Architecture Input voltage Input frequency Input voltage range On-line double conversion VFI-SS-111 Sinusoidal Conventional with extendable backup time 230 V Hz ± 5% autosensing 184 V 265 V at 100% load THD of input current 3% Input power factor 0.99 Output voltage 230 V ± 1% Output frequency (nominal) 50/60 Hz synchronised Peak factor 3.5:1 THD of output voltage 1% Permitted overload Bypass 300% for 1 sec, 200% for 5 sec, 150% for 30 sec Automatic, internal, synchronised, electromechanical (for overloads and operating problems) Backup time extension yes No Battery range type/voltage VRLA - AGM 48 VDC VRLA - AGM 36 VDC VRLA - AGM 144 VDC VRLA - AGM 192 VDC Backup time (min) Screen and signalling Communication ports Remote control 1 RS232 serial port Multi-coloured LED status indicator, alarms and audible signalling 1 RS 232 serial port, 1 logic level port Software can be downloaded free of charge 1 RS 232 serial port, 1 logic level port, 1 slot for network interface connection (eg: CS121) Dimensions (H x W x D) (mm) 355 x 88 x x 160 x x 270 x 570 Dimensions of battery cabinet (H x W x D) (mm) 319 x 160 x x 160 x x 160 x 402 Net weight (kg) Ambient operating temperature ( C) 0 to 40 Relative humidity (%) 20 to 80 Protection index Ip 21 Noise at 1 m (dba) Heat dissipation (BTU/h) Reference product standards EN , EN , EN note: The backup times, expressed in minutes, are measured under optimum operating conditions. CONVENTIONAL UpS 43