HANDRAIL SCALE PH-740 INSTRUCTION MANUAL

Transcription

1 HANDRAIL SCALE PH-740 INSTRUCTION MANUAL Please keep this manual in a safe place, an make sure it is reaily available whenever necessary. Please use this prouct only after carefully reaing this manual an fully unerstaning its contents.

2 1. Table of Contents 3. Base on NIH/WHO BMI Guielines 2. Safety Notes 2 3. Base on NIH / WHO BMI Guielines 3 4. Part Names & Accessories 3 5. Assembly Instructions 4 Obese Obese Obese Uner Weight Normal Range Pre obese CLASS l CLASS ll CLASS lll BMI BMI BMI BMI BMI 40 BMI Operation by AC aapter 7 7. Operation by batteries 7 8. Operation 8 9. Measuring height proceure Output ata format Specifications 13 Battery Case 4. Part Names & Accessories Accessories AC Aapter Screw x 8 12.Troubleshooting Safety Notes Height Ro Arm Display Box Instruction Manual Caution Symbols For optimum performance an safety, please familiarize yourself with the Caution Symbols below. These symbols are esigne to alert the user to potential hazars when using this equipment. Ignoring these Caution Symbols may result in serious injury, or amage to the prouct. Please be sure to review before proceeing with the INSTRUCTION MANUAL. WARNING This symbol inicates the possibility of serious injury if the prouct is mishanle or instructions are ignore. This symbol inicates the possibility of physical injury or equipment amage if instructions are ignore. CAUTION This symbol inicates general precautions that shoul be taken when using this prouct. WARNING Inserting an Removing the AC aapter to reuce the risk of electric shock or prouct amage, never insert or remove the AC aapter with wet hans. Do not uner any circumstances ismantle or alter the evice, as this coul result in electric shock or injury as well as aversely affecting the precision of measurement. To prevent fire hazar use only a correctly wire (120V AC) outlet, an o not use a multiple outlet extension cable. CAUTION Please make sure you place the scale on a level an stable surface. If the equipment is use when the scale is unstable, because not all feet are on the surface, there may be a risk of injury or inaccurate measurement. Measurement may be inaccurate when the scale is place on a thick-pile rug or carpet. Never jump on the scale, there may be a risk of injury an malfunction of the equipment. Do not hang on the hanrail. The equipment must be use with the inclue AC aapter only. Do not insert or remove the AC plug by the cable. Do not place a finger into any gap or any hole of the equipment. You may be injure. Please use caution when ajusting the height ro to prevent injury. Please return the height ro to the storage position after completion of measurement. Please o not touch or lean on the height ro or the isplay uring weighing as this will reuce accuracy. Maintenance This is a precision manufacture an accurately calibrate prouct. Please observe the following instructions. If the equipment is move to a place with a temperature ifference of 18 F/10 C or more, leave if for at least two (2) hours before use. Avoi subjecting the equipment to excessive shocks or vibrations. Never isassemble or ajust the equipment, as this may cause malfunctions. When not in use for an extene time, unplug the AC aapter from the outlet. Do not wipe the equipment with corrosive chemicals (benzene, acetone, etc.). Please use a neutral etergent to clean the equipment. Do not use cellular phones or microwave therapy equipment near this equipment. It may not measure correctly ue to equipment malfunction. When isposing of this equipment, please o so in accorance with the prevailing regulations in your country, state an city. If an unauthorize person attempts to isassemble or repair any part of the equipment, the warranty will become invali. When the unit malfunctions, please consult your nearest Tanita sales office or agent. Hanrail 2 3 Platform BMI Select BMI moe / Ajust height for BMI Wheel Ajustable Feet Clip x 3 The clips are for holing the AC aapter cable an USB cable. Attach the clips to the rear of the pillar as illustrate. kg/lb Select kg or lb for unit measurement ON/ZERO Turns the power on an sets zero

3 5. Assembly Instructions 1. List of Components 2. Assembly Base (fully assemble an pre-wire to isplay assembly) Cable (Base sie) Lower Pillar Assembly Screw Cable (Top Hea Display Assembly Sie) Top Hea Display Assembly (fully assemble an pre-wire to base) Back Cover 1) Install the Lower Pillar Assembly into the Base using the four (4) Screws while carefully avoiing pinching the cable. *Tighten the screws completely. 2) Assemble the Top Hea Display into the Lower Pillar assembly while carefully inserting the cable into Lower Pillar assembly an extening it the full length of the Lower Pillar. 3) Connect the Cable from the bottom of the lower pillar assembly to the cable on the base. Front Cover Top Height Ro Assembly (fully assemble with pivoting height measuring lever) 4) Place the Hanrail on the Base. Height Ro Arm Lower Height Ro Assembly Hanrail Brace 5) Insert the tabs of the brace into the slot. Putting your weight on the hanrail to ajust its position will facilitate insertion of the brace into the slot. Slie the brace completely to the en (Position mark). 6) Clamp the hanrail to the brace using the four screws. *Tighten the screws completely. 4 5

4 5. Assembly Instructions (continue) 10) Insert the Hight Ro Assembly into the Pillar. 7) Place the Front Cover over the screws an fix it by inserting its pins into the holes. *Be careful not to pinch the cable while performing this operation. 8) Insert the Back Cover. Note: Place the scale on a har, flat surface where these is minimal vibration to ensure safe an accurate measurement. If use on an uneven surface, feet may be ajuste to ensure a level an stable platform. * Feet ajustment shoul be performe by two persons or more. Note: To move the scale, hol the Top Hea Display to pivot the scale on its wheels an move it tilte. 9) Connect the top Height Ro Assembly an Lower Height Ro Assembly together. Connect both pillars completely. Using the floor, push straight own on the upper pillar into the lower pillar. IF unable to connect, go to step Operation by AC aapter AC aapter is much preferable when the scale will be use continuously. 1) Insert the AC aapter jack into the AC aapter inlet on the back sie of isplay. 2) Plug the AC aapter into the outlet. WARNING In orer to reuce the risk of electric shock, never insert or remove the power coe with wet hans. CAUTION This equipment must be use with the inclue AC aapter only. 7. Operation by batteries CAUTION Do not grip the sliing height bar while pushing own on the upper pillar. Do not use a slippery floor surface. Use caution to avoi pinching fingers uring assembly. 1-1) 1-2) 1) When the batteries start to run low, Lo appears on the isplay panel as a warning. 2) Pull up the battery case which locate on top of isplay. All batteries shoul be immeiately replace with new ones at the same time. Do not use a combination of alkaline an manganese batteries, as such an arrangement may result in equipment failure. Rechargeable batteries are NOT recommene use. 3) Push own the battery case completely. Image * Insert new batteries such that the negative terminals of the batteries are pushe up against the coils within the battery case. 6 7

5 8. Operation 1. Stanar Weighing Proceures 3. Step on Function 1) Turn on the power by pressing the key. The scale will turn on automatically when the user steps onto the platform. Note: If the weight is less than 22lb/10kg, the Step-On function will not work. 2) After all the segments flash, [0.0lb/0.0kg] is isplaye. If person less than 22lb/10kg, press the key manually to turn on the scale. 3) The person to be weighe shoul still in the mile of the platform. If an item is place on the scale while it is powere off, accurate measurement will not be possible an the Step on Function may not operate properly. When measurement has been starte using the Step on Function, installing or removing the AC aapter, cable or batteries while power is off may prevent accurate measurement. Perform measurement after having presse the key an turne off the Step on Function. 4) The weight will be locke-in an isplaye on the isplay. (Hol) sign will appear in the upper left corner of the isplay. When the scale is connecte to an external evice, weight ata will be exporte at this time. 5) The scale will automatically shut off in 30 secons. Note: Do not press the key while staning on the scale, as accurate measurement will not be possible. 2. BMI Weighing 1) Turn on the power by pressing the key. 4. Changing Measurement Units This function is use to change the measurement units on the isplay. e.g. When change the unit lb to kg. Press the key. The measure shifts from lb to kg an the measurement units change. 2) After all the segments flash, [0.0lb/0.0kg] is isplaye. (or ) 3) The person to be weighe shoul still in the mile of the platform. 4) The weight will be locke-in an isplaye on the isplay. (Hol) sign will appear in the upper left corner of the isplay. 5) Press the key (or ). The efault height [5ft7.0in/170cm] will be isplaye. 6) Set the height with the key. 7) Once the height an weight have been establishe, press the key. The weight an BMI calculation will then be isplaye. When the scale is connecting to an external evice, weight, height an BMI ata will be exporte at this time. 8) The scale will automatically shut off in 30 secons. The setting of height for BMI is can be accomplishe in any one of the following means by pressing the key (or ). Before stepping on the scale. After pressing the key. After weight measurement while the weight result remains on the isplay. 8 9

6 9. Measuring height proceure 10. Output ata format The user shoul step on the platform without wearing shoes for accurate This section covers the exporting of ata from the scale to an external evice (e.g. PC) using a RS-232C an USB compliant signal. measurement. Always have someone assist the user for accurate measurement. RS-232C an USB interface are for ata OUTPUT ONLY! This scale is not capable of receiving instructions from an external evice. 1) Ajust the Height Ro Arm position before the user steps on the platform. Place han on the Height Ro Arm. If the subject is taller than 48 / 120 cm, pull the Height Ro Sliing Block an Height Ro Arm at the same time upwar so that the arm is positione higher Specifications Communications stanar Communications metho EIA RS-232C compatible Asynchronous transaction USB than the subject s hea. If the subject is shorter than 48 / 120 cm, move the Height Ro Arm own. Correct way to hol the Height Ro Arm Signal spee Data bit length Parity 9600 bau 8 bits None Stop bit 1 bit Terminator CR+LF Note: An RS-232C connector (D sub 9-pin female) an USB connector (B-type 4-pin female) are locate on the back of the isplay unit. Please provie your own cables as necessary as none are inclue. RS-232C :Straight D sub 9-pin (male) D sub 9-pin (female) USB :A-type 4-pin (male) B-type 4-pin (male) Incorrect way to hol the Height Ro Arm Select Switch : Please select which interface you woul like to use RS-232C Port RS-232C/USB Select SW USB Port To avoi anger of breaking or coming loose, you must hol the height ro arm securely. 2) Gently lower the Height Ro Arm until the Height Ro Arm touches the very top of the user s hea. 3) Rea the measurement. If the subject is taller than 48 / 120 cm, rea the number just above the top of the Upper Pillar Column (see example #1). If the subject is shorter than 48 / 120cm, rea the number below the Height Ro Arm (see example #2). CORRECT way to measure the height of 48" / 120cm or more INCORRECT way to measure the height of 48" / 120cm or more Signal Line Name an Connection Metho If you want to use the USB output, you must install the necessary river onto your PC, available to ownloa from Terminal no. Signal name 1 2 TXD RXD 4 5 GND Example #1: 58"(147.5 cm) READ HERE Example #2: 36.25" (92 cm) Reaing the height measurement of 48" / 120cm or MORE Reaing the height measurement of 48" / 120cm or LESS 10 11

7 Output ata 11. Specifications Name of item Heaer Pattern Output ata (ASCII coe) kg moe lb moe BMI moe Weight moe Control ata Control ata Control ata {0 0 1 Fix to 16 Fix to 1 Fix to 1 2 Bytes fixe 1 Byte fixe 1 Byte fixe Control ata 2 Fix to 1 1 Byte fixe Moel MO "PH-740" 8 Byte fixe Height Hm Hf xxx.x x.xx.x 4 6 bytes Weight Wk Wp xxx.x xxxx.x 3 6 bytes BMI MI xxx.x 3 5 bytes Checksum CS xx 2 Bytes fixe Note: The ata are ivie with commas (,) for each ata. The terminator (en of the ata) is CR (ASCII coe 0DH), LF (ASCII coe 0AH). The control ata for the items 1 4 are for expansion. They are not use presently so the receiving sie can ignore them. When the measurement unit is select the "lb",all the height ata is converte into ft-in an it is output. Because of its specifications, the scale will output an irrelevant signal approximately 0.1 secon after ata output. Make sure you ignore this signal an o not import it. Weight Measurement Height Measurement Input Items Output Items Size Moel Measurement System Maximum Capacity / Minimum Grauation Stanar Range of Weight Step on Measurement System Range of Height Height Weight Display Height BMI Overall Platform Display Output Data Interface Power Source PH-740 Strain Gauge Loa Cell 1000lb / 0.2lb 450kg / 0.1kg lb 0-450kg lb kg Mechanical Height Ro 2ft 1in 7ft 64cm 214cm 2ft 8ft 2in 0.5in increment 61cm- 250cm 1cm increments 1000 lb / 0.2lb 450kg / 0.1kg 2ft 8ft 2in 0.5in increment 61cm- 250cm 1cm increments 0.1 increments D31.5 x W31.9 x H53.8in D800 x W810 x H1366mm D22.5 x W26.1 x H1.4in D572 x W664 x H36mm Upper 5Digits an Lower 4Digits LCD Height of numerals 1in / 24mm RS-232C (D sub 9-pin Female connector) USB (B-type) AC aapter (inclue) Center Minus [Output example (in the case to lb unit)] Power Consumption 0.3 W max. Temperature Range of usage 32 F - 95 F 0 C - 35 C Weight of Equipment 64.0lb (without batteries) 29.0kg (without batteries) Battery Life Approximately 100hours of continuous use when using LR6 (AA Alkaline battery) 12. Troubleshooting If you are concerne that the scale may not be functioning correctly, please check the following point before requesting repairs. Problem Nothing is isplaye when is presse. Lo is isplaye. Measurement is not accurate. key Check Points Check the connection of the AC aapter jack to the AC aapter inlet, an the connection of the AC aapter plug to the outlet. The batteries may be weak. Try an AC aapter or new LR6 (AA) batteries. Check the terminals of the batteries for contamination The batteries are running out. Please replace them immeiately or use the AC aapter. Check that all feet of scale are stable an on a har flat surface, carpeting epth shoul be kept to a minimum. After having steppe own from the scale an presse the key, perform the measurement again. Accurate measurement may be impossible if the prouct is use where there is excessive vibration. Try using the prouct in a ifferent place. The weight oes not stabilize OL is isplaye -OL is isplaye Error is isplaye The Top Hea Display Assembly is loose. Are you moving uring measurement? Is the measure weight within the range of weight measurement? During measurement, are you touching any part other than the hanrail, such as the height ro arm, switch, or another part? The range of weight (1000lb/450kg) is exceee. Was anything place on the scale before measurement? Check whether the cable between the platform an isplay is isconnecte, cut, or pinche. Retighten the four screws that attach the base to the Lower Pillar Assembly

8 USA an Canaa Feeral Communications Commission an Canaian ICES Notice This equipment has been teste an foun to comply with the limits for a Class B igital evice, pursuant to Part 15 of the FCC Rules an Canaian ICES-003. These limits are esigne to provie reasonable protection against harmful interference in a resiential installation. This equipment generates, uses an can raiate raio frequency energy an, if not installe an use in accorance with the instructions, may cause harmful interference to raio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment oes cause harmful interference to raio or television reception, which can be etermine by turning the equipment off an on, the user is encourage to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment an receiver. Connect the equipment into an outlet on a circuit ifferent from that to which the receiver is connecte. Consult the ealer or an experience raio or television technician for help. Moifications The FCC requires the user to be notifie that any changes or moifications mae to this evice that are not expressly approve by Tanita Corporation may voi the user s authority to operate the equipment TANITA Corporation. All Rights Reserve. PH (1)