13.6 PREVENTIVE MAINTENANCE FOR THE SERIES 50G ENGINE (CITY TRANSIT COACH)
|
|
- Estella Barrett
- 7 years ago
- Views:
Transcription
1 SERIES 50 SERVICE MANUAL 13.6 PREVENTIVE MAINTENANCE FOR THE SERIES 50G ENGINE (CITY TRANSIT COACH) The following is a list of items that are unique to the Series 50G engine for preventive maintenance (city transit coach): Coalescing Fuel Filters Drain coalescing fuel filters daily. Inspect natural gas fuel filter every 6,000 miles (9,600 km). Replace fuel filter if dirt, debris or foreign objects are present inside of the fuel filter. Also, replace if fuel filter seal is damaged. NOTE: Oil saturation on the outside of the fuel filter is a NORMAL condition of the oil coalescing process Valve Lash Check valve lash. Valve lash should be inspected and adjusted every 60,000 miles (96,000 km) as specified Closed Crankcase Breather System The closed crankcase breather filter must be replaced every 6,000 miles (9,600 km). The filter is located in the remote mounted crankvent assembly DryTypeAirCleaner Under no operating condition should the intake restriction exceed 20 inches of water at full load and rated speed. A clogged air cleaner element will cause excessive intake restriction and a reduced air supply to the engine. For equivalent restriction limits for lower speed, refer to Detroit Diesel Corporation Engineering Bulletin No. 39, "Air Cleaner Systems for Detroit Diesel Engines". Inspect the air cleaner element every 12,000 miles (19,300 km) (coaches). Inspect the air cleaner at 5,00 miles (8,000 km ) if the engine is operated under severe dust conditions. Replace the element if necessary. Check the gaskets for deterioration and replace, if necessary. If the dry type air cleaner is equipped with an aspirator, check for aspirator damage or clogging. Clean and repair as necessary Engine Lubricating Oil Change the lubricating oil every 6,000 miles (9,600 km) for city transit coaches. (Refer to Engine Requirements - Lubricating Oil, Fuel and Filters - 7SE272). All information subject to change without notice. (Rev. 2005) 6SE Copyright 2005 DETROIT DIESEL CORPORATION From Bulletin
2 13.6 PREVENTIVE MAINTENANCE FOR THE SERIES 50G ENGINE (CITY TRANSIT COACH) Engine Lubricating Oil Filters Change the lubricating oil filters at each oil change 6,000 miles (9,600 km) for city transit coaches) Coolant Check the coolant level daily before starting the engine. Make sure coolant is up to the proper level. Add coolant as necessary. DO NOT OVERFILL. Check all cooling system lines and hoses for damage, leaks or loose connections. Tighten or replace as necessary. (Refer to Coolant Selections for Detroit Diesel Engines 7SE298). Check for proper inhibitor level at each oil change 15,000 miles (24,000 km) and add as required or 6,000 miles (9,600 km) (coaches) Turbocharger and Wastegate Assembly Inspect turbocharger mountings, air intake and exhaust ducts, recirculation valve assembly, and wastegate valve assembly, including hoses, for leaks. Check the oil and water inlet and outlet lines and connections for leaks and restrictions to flow. Check for unusual vibrations or noises. If excessive, remove unit from service and have cause corrected Turbocharger Compressor Recirculation Valve Every 18,000 miles (28,900 km), vacuum check the turbocharger compressor recirculation valve for leakage per the service manual. If the valve assembly does not hold the vacuum specified, the valve needs to be disassembled and inspected for defective components Thermostat Check thermostats and seals every 108,000 miles (173,800 km) (coach). Replace the seals and/or thermostat, if necessary Spark Plugs Replace the spark plugs and boot spring assembly every 24,000 miles (38,600 km) (coach); refer to Section 15.5 and refer to Section for plug information Spark Plug Ignition Wires Inspect spark plug wires at spark plug change interval for cracks and/or deterioration, and for proper routing. Replace wires at 108,000 miles (173,800 km) (coach). (Rev. 2005) All information subject to change without notice From Bulletin SE Copyright 2005 DETROIT DIESEL CORPORATION
3 SERIES 50 SERVICE MANUAL 13.7 MAINTENANCE OF SERIES 50G ENGINES Series 50G transit coach components must be maintained at various intervals ,000 Miles (10,000 km) Interval Maintenance for Transit Coach Every 6,000 miles (10,000 km), the following components must be maintained: ,000 Miles (19,000 km) Interval Maintenance for Transit Coach Every 12,000 miles (19,000 km), the following components must be maintained: ,000 Miles (29,000 km) Interval Maintenance for Transit Coach Every 18,000 miles (29,000 km), the following components must be maintained: ,000 Miles (39,000 km) Interval Maintenance for Transit Coach Every 24,000 miles (39,000 km), the following components must be maintained: All information subject to change without notice. (Rev. 2005) 6SE Copyright 2005 DETROIT DIESEL CORPORATION From Bulletin
4 13.7 MAINTENANCE OF SERIES 50G ENGINES Spark plugs, boot spring assembly, refer to Section ,000 Miles (48,000 km) Interval Maintenance for Transit Coach Every 30,000 miles (48,000 km), the following components must be maintained: ,000 Miles (58,000 km) Interval Maintenance for Transit Coach Every 36,000 miles (58,000 km), the following components must be maintained: ,000 Miles (68,000 km) Interval Maintenance for Transit Coach Every 42,000 miles (68,000 km), the following components must be maintained: ,000 Miles (77,000 km) Interval Maintenance for Transit Coach Every 48,000 miles (77,000 km), the following components must be maintained: (Rev. 2005) All information subject to change without notice From Bulletin SE Copyright 2005 DETROIT DIESEL CORPORATION
5 SERIES 50 SERVICE MANUAL Spark plugs, boot spring assembly, refer to Section ,000 Miles (87,000 km) Interval Maintenance for Transit Coach Every 54,000 miles (87,000 km), the following components must be maintained: ,000 Miles (97,000 km) Interval Maintenance for Transit Coach Every 60,000 miles (97,000 km), the following components must be maintained: Valve lash, refer to Section ,000 Miles (106,000 km) Interval Maintenance for Transit Coach Every 66,000 miles (106,000 km), the following components must be maintained: ,000 Miles (116,000 km) Interval Maintenance for Transit Coach Every 72,000 miles (116,000 km), the following components must be maintained: All information subject to change without notice. (Rev. 2005) 6SE Copyright 2005 DETROIT DIESEL CORPORATION From Bulletin
6 13.7 MAINTENANCE OF SERIES 50G ENGINES Valve lash, refer to Section Spark plugs, boot-spring assembly, refer to Section ,000 Miles (126,000 km) Interval Maintenance for Transit Coach Every 78,000 miles (126,000 km), the following components must be maintained: ,000 Miles (135,000 km) Interval Maintenance for Transit Coach Every 84,000 miles (135,000 km), the following components must be maintained: ,000 Miles (145,000 km) Interval Maintenance for Transit Coach Every 90,000 miles (145,000 km), the following components must be maintained: Turbocharger recirculation valve, refer to Section (Rev. 2005) All information subject to change without notice From Bulletin SE Copyright 2005 DETROIT DIESEL CORPORATION
7 SERIES 50 SERVICE MANUAL ,000 Miles (154,000 km) Interval Maintenance for Transit Coach Every 96,000 miles (154,000 km), the following components must be maintained: Spark plugs, boot spring assembly, refer to Section ,000 Miles (164,000 km) Interval Maintenance for Transit Coach Every 102,000 miles (164,000 km), the following components must be maintained: ,000 Miles (174,000 km) Interval Maintenance for Transit Coach Every 108,000 miles (174,000 km), the following components must be maintained: Valve lash, refer to Section Crankcase breather element, refer to Section Thermostat, refer to Section Spark plug wires, refer to Section ,000 Miles (183,000 km) Interval Maintenance for Transit Coach Every 114,000 miles (183,000 km), the following components must be maintained: All information subject to change without notice. (Rev. 2005) 6SE Copyright 2005 DETROIT DIESEL CORPORATION From Bulletin
8 13.7 MAINTENANCE OF SERIES 50G ENGINES ,000 Miles (193,000 km) Interval Maintenance for Transit Coach Every 120,000 miles (193,000 km), the following components must be maintained: Spark plugs, boot spring assembly, refer to Section (Rev. 2005) All information subject to change without notice From Bulletin SE Copyright 2005 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
SERIES 60 SERVICE MANUAL The original air compressor is driven by the bull gear and water cooled. Engine coolant is fed to the compressor through a flexible hose tapped into the engine block water jacket
More informationCOOLING SYSTEM Section Page
5 COOLING SYSTEM Section Page 5.1 COOLANT PRE-HEATER... 5-3 5.2 COOLANT PUMP NON-EGR ENGINE... 5-7 5.3 COOLANT PUMP EGR ENGINE... 5-13 5.4 FRONT CONNECTOR HOUSING NON-EGR ENGINE... 5-17 5.5 FRONT CONNECTOR
More informationTrouble Shooting. Pump
Trouble Shooting Pump Trouble Possible Cause Remedy Oil leaking in the area of water pump crankshaft Worn crankshaft seal, bad bearing, grooved shaft, or failure of retainer o-ring. Excessive play on crankshaft
More informationThe cylinder head bolts tightening stages have been updated as listed in Table 1.
NUMBER: 07 EPA04 MBE 4000-6 S.M. REF.: 1.2.2 ENGINE: MBE 4000 DATE: November 2007 SUBJECT: CYLINDER HEAD BOLTS TIGHTENING STAGES PUBLICATION: 6SE412 The cylinder head bolts tightening stages have been
More informationEngine, Drive Train, and Hydraulic Repair Indicator Quick Reference Guide
Engine, Drive Train, and Hydraulic Repair Indicator Quick Reference Guide Planned Indicators Planned Indicators SM provide the best insight Service Meter Hours CAT Engine Repair Indicators Description
More informationTurbocharger system components, servicing
21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners
More informationCDS TROUBLESHOOTING SECTION I. VACUUM. 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg)
CDS TROUBLESHOOTING SECTION I. VACUUM 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg) 1.1. Clogged hoses or wand tube. Disconnect hoses and carefully check for an obstruction. 1.2. Excessive
More informationSELECTION, APPLICATION & MAINTENANCE
DIESEL PROTECTION SYSTEMS TPZ Engine Air Intake Shut Down Valves (Combined Automatic Overspeed and Air Pressure Operated Shut Down Bendix Types) SELECTION, APPLICATION & MAINTENANCE Valve Numbers TPZ-101
More informationMAINTENANCE OF WHEELMOVE IRRIGATION SYSTEMS
MAINTENANCE OF WHEELMOVE IRRIGATION SYSTEMS F. Richard Beard, Agricultural Equipment, Structures and Electricity Robert W. Hill, Biological & Irrigation Engineering Boyd Kitchen, Uintah County Extension
More informationREMOVAL AND INSTALLATION
303-01C-1 REMOVAL AND INSTALLATION Engine Body On Special Tool(s) Adapter For 303-D043 303-D043-02 or equivalent Special Tool(s) 303-01C-1 Turbocharger Lifting Bracket 303-1266 Wrench, Fan Clutch Nut 303-214
More informationMaintaining the Beauty and Performance of Your Boxster
Maintaining the Beauty and Performance of Your Boxster The Porsche Multi-Point Inspection Report The Porsche Multi-Point Inspection Report is completed by our Factory-trained Porsche Technicians every
More informationENGINE COOLING SYSTEM
ENGINE COOLING SYSTEM 1988 Toyota Celica 1987-88 TOYOTA Engine Cooling Systems Celica DESCRIPTION The basic liquid cooling system consists of a radiator, water pump, thermostat, cooling fan, pressure cap,
More informationNUMBER: 08 DD15-10 S.M. REF.: 3.2 ENGINE: DD15 DATE: September 2008
NUMBER: 08 DD15-10 S.M. REF.: 3.2 ENGINE: DD15 DATE: September 2008 SUBJECT: 3.2 OIL PAN PUBLICATION: DDC-SVC-MAN-0002 Oil pan section 3.2 has been updated. Section Change 3.2 Oil Pan Call-outs have been
More informationEmission Control Systems Warranties
2004 Chevrolet TrailBlazer - 2WD Emission Control Systems Warranties This section outlines the emission warranties that General Motors provides for your vehicle in accordance with the U.S. Federal Clean
More information3/5/2015. Oil Analysis Tests. Lubricating Oils. Six Functions of Lubricating Oil
Oil Analysis Tests Oil analysis is a series of laboratory tests used to evaluate the condition of used lubricants and equipment components. By studying the results of the used oil analysis tests, a determination
More informationCummins Westport, Inc. Engine Overview. March 2015
Cummins Westport, Inc. Engine Overview March 2015 Cummins Westport Inc. (CWI) A Cummins JV Company CWI was established in 2001 as a 50/50 joint venture company between Cummins Inc and Westport Innovations.
More informationWHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW?
WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW? Owner Checks and Services Refer to Mileage Intervals for Additional Checks and Services Certain basic maintenance checks and inspections should be performed
More informationActuator-Swirl Valve DESCRIPTION
US/Canadian 2007 Sprinter Diesel V6 Dodge Service Manual Swirl Valve Info Actuator-Swirl Valve DESCRIPTION The swirl valve linkage links the swirl valves in the intake manifold to the swirl valve actuator.
More informationChapter 7 Hydraulic System Troubleshooting
Chapter 7 Hydraulic System Troubleshooting General The following troubleshooting information is provided as a general guide to identify, locate and correct problems that may be experienced with the hydraulic
More informationMaintaining the Beauty and Performance of Your 911
Maintaining the Beauty and Performance of Your 911 The Porsche Multi-Point Inspection Report The Porsche Multi-Point Inspection Report is completed by our Factory-trained Porsche Technicians every time
More informationUNITED STATES AND U.S. TERRITORIES AND POSSESSIONS EXCEPT PUERTO RICO 2016 / WARRANTY & MAINTENANCE MANUAL
UNITED STATES AND U.S. TERRITORIES AND POSSESSIONS ECEPT PUERTO RICO 2016 / WARRANTY & MAINTENANCE MANUAL Maintenance Service precautions Vehicle maintenance is an important yet frequently neglected item.
More information3620 W 11th Streetб Houston, TX 77008 Telephone: 713-635-6291 Email: sales@kellogg-american.com Website: www.kellogg-american.com
Unpackaging & Handling Be sure to carefully inspect the unit before accepting the shipment. If any damage has occurred document it with the trucking company immediately. Contact your Kellogg Distributor
More informationTURBO Installation Instructions: General
Diagnostic Check of Engine Step 1: Before Replacing A Turbo It is important to conduct a thorough diagnostic check of the engine system to determine if the fault is actually the turbocharger. A lack of
More informationIntake Manifold: Service and Repair
2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 Copyright 2008, ALLDATA 9.90 Page 1 Intake Manifold: Service and Repair Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement.
More informationC32 MARINE ENGINE (RXB)
SAFETY.CAT.COM C32 MARINE ENGINE (RXB) Maintenance Intervals Excerpted from Operation & Maintenance Manual (SEBU7908-09) 2009 Caterpillar All Rights Reserved SEBU7908-09 69 Maintenance Interval Schedule
More information6 Crankcase Ventilation
6 Crankcase Ventilation Introduction... 6-3 Crankcase Ventilation Manager (CVM)... 6-5 Introduction... 6-6 CVM280B..................................... 6-7 CVM280T... 6-10 CVM424B....................................
More informationNational Competency Based Skill Training Refrigeration and Air-conditioning Mechanic Logbook
National Competency Based Skill Training Refrigeration and Air-conditioning Mechanic Logbook Trainee:... Training Provider:... Year:... Trainee Contact no:... Competency Based Skill Training Logbook Introduction
More informationPUMP MAINTENANCE SCHEDULE AND CHECKLISTS
PUMP MAINTENANCE SCHEDULE AND CHECKLISTS Providing a maintenance schedule defined specifically by run hours or yardage pumped serves only as a general guideline given the large amount of variables a unit
More informationLUBRICATION SYSTEM Section Page
4 LUBRICATION SYSTEM Section Page 4.1 ENGINE OIL CIRCUIT... 4-3 4.2 OIL SPRAY NOZZLE... 4-5 4.3 OIL PUMP... 4-12 4.4 OIL FILTER HOUSING... 4-15 4.5 OIL FILTER ELEMENT... 4-17 4.6 HEAT EXCHANGER... 4-19
More informationENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER...
FUEL FILTER............................ FUEL HEATER.......................... INJECTOR.............................. SUPPLY PUMP.......................... COMMON RAIL.......................... FUEL PRESSURE
More informationMAINTENANCE INTERVALS
MAINTENANCE INTERVALS Operation and Maintenance Manual Excerpt 2010 Caterpillar All Rights Reserved SEBU8407-03 November 2009 Operation and Maintenance Manual 279C, 289C and 299C Compact Track Loaders
More informationSkills Standards MEDIUM/HEAVY DUTY TRUCK: DIESEL ENGINE REPAIR TECHNICIAN OD32151 ALIGNED WITH ASE/NATEF
Skills Standards MEDIUM/HEAVY DUTY TRUCK: DIESEL ENGINE REPAIR TECHNICIAN OD32151 ALIGNED WITH ASE/NATEF Competency-Based Education: OKLAHOMA S RECIPE FOR SUCCESS BY THE INDUSTRY FOR THE INDUSTRY Oklahoma
More informationFS Lubricants. Oil Analysis Program
FS Lubricants Oil Analysis Program What can an oil analysis do for you? 1. Establish safe and proper drain intervals. 2. Provide a reduction in unforeseen breakdowns. 3. Reduce down time. 4. Minimize the
More informationPREVENTION MAINTENANCE CHECKLIST FOR TRACTORS, TRUCKS, AND AUTOMOBILES
PREVENTION MAINTENANCE CHECKLIST FOR TRACTORS, TRUCKS, AND AUTOMOBILES Farm Machinery Fact Sheet FM-21 By Dr. Von H. Jarrett, Extension Agricultural Engineer Systematic sequence for inspection GASOLINE
More information3208 MARINE ENGINE Maintenance Intervals
SAFETY.CAT.COM 3208 MARINE ENGINE Maintenance Intervals Excerpted from Operation & Maintenance Manual (SEBU6090-03-01) 2007 Caterpillar All Rights Reserved 56 Maintenance Interval Schedule i00917973 Maintenance
More informationTechnical Guide 08/15/14
Technical Guide 08/15/14 1 Table of Contents Contact information.3 Identifying your system..4-8 Model Number Serial number location Parts of your fuel system..9-14 Fuel pump diagram Wire harness schematics
More informationAGENDA STAFF REPORT. Budgeted: Yes Current Year Cost: $695,000 Annual Cost: N/A
AGENDA STAFF REPORT Agenda Item ASR Control 13-001267 MEETING DATE: 10/22/13 LEGAL ENTITY TAKING ACTION: Board of Supervisors BOARD OF SUPERVISORS DISTRICT(S): 2 SUBMITTING AGENCY/DEPARTMENT: John Wayne
More informationSystem Saver 318 Air Compressor for Mack E-Tech and ASET Engines
Maintenance Manual 31 System Saver 318 Air Compressor for Mack E-Tech and ASET Engines Revised 08-05 NON-THROUGH DRIVE THROUGH DRIVE Service Notes About This Manual This manual provides service and repair
More informationMINNESOTA WEST COMMUNITY & TECHNICAL COLLEGE COURSE OUTLINE
MINNESOTA WEST COMMUNITY & TECHNICAL COLLEGE COURSE OUTLINE Faculty are required to have the outline submitted to the Academic Affairs Office. The course outline is the form used for approval of new courses
More informationMIDLAND COLLEGE SYLLABUS DEMR 1323 AUTOMOTIVE HEATING AND AIR CONDITIONING 2-4
Course Description: Text, References and Supplies: Course Goals/Objectives: Theory of automotive air conditioning and heating systems. Emphasis on the basic refrigeration cycle and diagnosis and repair
More informationPerfectly Adapted. ISL Euro 6 Gas Engine 250-320PS
Perfectly Adapted ISL Euro 6 Gas Engine 250-320PS Cummins ISL-G The ISL G is the natural choice in alternative-fuel engine technology. With industry leading performance, it combines all the advantages
More information11101, 11108 & 11151 INSTALLATION INSTRUCTIONS
11101, 11108 & 11151 INSTALLATION INSTRUCTIONS WARNING! The fuel system is under pressure. Do not open the fuel system until the pressure has been relieved. Refer to the appropriate vehicle service manual
More informationThe Aftertreatment System Technician's Guide has been revised.
NUMBER: 2 ATS 07 S.M. REF.: Listed in Table 1 ENGINE: ATS DATE: April 2007 SUBJECT: UPDATES TO AFTERTREATMENT SYSTEM TROUBLESHOOTING PUBLICATION: 7SE63 The Aftertreatment System Technician's Guide has
More informationSELECTION, APPLICATION AND MAINTENANCE
DIESEL PROTECTION SYSTEMS D-Series Engine Automatic Overspeed Shut Down Valves (Spindle Types with Air Pressure and Manual Shut Down Options) SELECTION, APPLICATION AND MAINTENANCE Valve Numbers D92-AP
More informationSection 7 Adjustment, Repair and Replacement
Section 7 Adjustment, Repair, and Replacement Page 7-1 Section 7 Adjustment, Repair and Replacement Section Contents Page Overview...7-5 Belts Belt Guard Removal/Installation...7-7 Belt Removal/Installation...7-11
More informationTECHNICAL BULLETIN. Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves. How the Cab Leveling and Chassis Leveling Valves Work
Revised 02-00 TECHNICAL BULLETIN Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves This technical bulletin covers both cab and chassis leveling valves manufactured by Meritor WABCO. While the
More informationHVAC Design Requirements
Maintenance of HVAC HVAC Design Requirements Air Flow Diagram แบบ Recirculation Air Flow Diagram แบบ Once Through Definition Of Conditions As built At rest In operation air air air Maintenance GMP Requirements
More informationENGINE COOLING FAN. 1987 Lincoln Mark VII COOLING SYSTEM SERVICING DESCRIPTION MAINTENANCE DRAINING CLEANING FLUSHING
ENGINE COOLING FAN 1987 Lincoln Mark VII 1987 ENGINE COOLING Ford Motor Co. Engine Cooling Fans Ford; Crown Victoria, Escort, Mustang, Taurus, Tempo & Thunderbird Lincoln; Continental, Mark VII & Town
More informationSELECTION, APPLICATION AND MAINTENANCE
DIESEL PROTECTION SYSTEMS Automatic Diesel Engine Shut Down System for Safe Area Applications SELECTION, APPLICATION AND MAINTENANCE Series 300 Series 310 SYSTEM DESCRIPTION Suitable for attended engine
More informationTable Z. Troubleshooting Chart for Air Conditioners. Cause
Troubleshooting Chart for Air Conditioners Type of Unit Complaint Cause With open-type compressor Electric motor will not start Power failure Check circuit for power source Compressor stuck Locate cause
More informationWater Pump Replacement
1 of 8 2/5/2008 6:36 AM Document ID# 713637 2001 Cadillac Seville Print Water Pump Replacement Tools Required 1. J 38816-A Water Pump Remover & Installer 2. J 38185 Hose Clamp Pliers
More informationA Truck Driver s Guide to Care and Maintenance of Diesel Particulate Filters (DPFs)
A Truck Driver s Guide to Care and Maintenance of Diesel Particulate Filters (DPFs) Disclaimer: This handbook is not a substitute for the detailed instructions/warranty limitations supplied by the manufacturer
More informationDiesel: Troubleshooting
Diesel: Troubleshooting Probable Cause Engine not starting Hard to start engine Runs rough at lower RPM Lack of power Diesel knock / pinking Black White Blue Low compression X X X Low fuel pressure X X
More informationUSER S, MAINTENANCE and SERVICE INFORMATION MANUAL
CONTENTS SAFETY INFORMATION................ 2 FOR YOUR SAFETY....................... 2 SYSTEM OPERATION.................. 2 THERMOSTATS........................... 2 INTERMITTENT IGNITION DEVICE...........
More informationHow To Fix A Car With A Carbide Engine
Section 12 Adjustment, Repair, and Replacement Page 12-1 Section 12 Adjustment, Repair and Replacement Section Contents Page Overview...12-5 Belts Belt Guard Removal/Installation...12-7 Belt Removal/Installation...12-11
More informationTable V. Troubleshooting Checklist for Refrigeration Systems. Air or non-condensable gas in system. Inlet water warm.
Table V Troubleshooting Checklist for Refrigeration Systems TROUBLE POSSIBLE CAUSE CORRECTIVE MEASURE High condensing pressure. Low condensing pressure. Air or non-condensable gas in system. Inlet water
More informationFire Hydrant Troubleshooting
Fire Hydrant Troubleshooting Pulsation or chatter during opening and flow of water from hydrant. Loose condition in stem at lower valve plate nut. Tighten lower valve plate nut and secure with SS lock
More informationVehicle Maintenance Policies and Procedures
Vehicle Maintenance Policies and Procedures Adopted: 09/20/2011 1 Table of Contents Introduction:... 4 Goals and objectives:... 5 Goals:... 5 Objectives:... 5 Preventative Maintenance:... 6 Daily... 6
More informationBoiler and Burner Cleaning and Servicing Specifications
Boiler and Burner Cleaning and Servicing Specifications The Town of Groton of Public Works Department is requesting bids to provide manufacturers recommended maintenance, repairs and emergency service
More informationCylinder head, removing and replacing
15-1 Cylinder head, removing and replacing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once, and are unreliable and may fail
More informationAttachment J-C18.1. HVAC Work Instructions
. RFP: Attachment J-C18.1 HVAC Work Instructions NNC13ZFD017J SOW Item No. Title Page C18-02 Control Air Systems Annual PM 2 C18-03 Split System AC Indoor Section Annual PM 3 C18-04 Condensing Unit Semi-Annual
More informationAustin High School Automotive Service Technology Engine Repair 9 th grade Course Syllabus
Austin High School Automotive Service Technology Engine Repair 9 th grade Course Syllabus 1 Prerequisites: Students entering the Automotive Technology Program for engine repair must be of the ninth grade
More informationSection 11 - System Diagrams
Section 11 System Diagrams Page 11-1 Section 11 - System Diagrams Section Contents Page Overview...11-3 Flow Diagram, Fuel System...11-4 Flow Diagrams, Lubricating Oil System...11-5 Flow Diagrams, Cooling
More informationWynn s Extended Care
Wynn s Extended Care Every car deserves to receive the very best care... especially yours. How Do You Keep Your Reliable Transportation Reliable? Count on Wynn s Because Wynn s has been caring for cars
More informationSPECIFICATION TECHNICAL AIR-CONDITIONING UNITS SINGLE AND SPLIT (DUCTED) (AIR COOLED PACKAGED UNIT)
SPECIFICATION TECHNICAL AIR-CONDITIONING UNITS SINGLE AND SPLIT (DUCTED) (AIR COOLED PACKAGED UNIT) MAINTENANCE TYPE: STATUTORY 1.0 SCOPE OF SERVICES The Contractor shall provide maintenance Services for
More informationSERVICE BULLETIN AIR CONDITIONER COMPRESSOR FAILURES ALSO SEE BULLETIN #SB3-304AS (SYSTEM CONTAMINATION)
Form #SB4-304AS AirSourceR SERVICE BULLETIN AIR CONDITIONER COMPRESSOR FAILURES ALSO SEE BULLETIN #SB3-304AS (SYSTEM CONTAMINATION) Second only to refrigerant hose leaks, compressors have the highest rate
More informationATLAS AIR COMPRESSOR OPERATING INSTRUCTIONS COMPRESSOR IDENTIFICATION
ATLAS AIR COMPRESSOR OPERATING INSTRUCTIONS PLEASE READ THIS MANUAL BEFORE USING YOUR AIR COMPRESSOR. KEEP THIS MANUAL FOR FUTURE REFERENCE AS TO THE PROPER OPERATION AND MAINTENANCE OF YOUR AIR COMPRESSOR.
More informationTraining Syllabus to Instruct/Prepare for the ASE Transit Bus Diesel Engines Test
APTA STANDARDS DEVELOPMENT PROGRAM RECOMMENDED PRACTICE American Public Transportation Association 1666 K Street, NW, Washington, DC, 20006-1215 APTA-BTS-BMT-RP-005-10 Approved October, 2010 APTA Bus Maintenance
More informationaccidents which arise due to nonobservance and the safety information herein.
20 GALLON COMPRESSOR Model: 7342 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This
More informationMaintenance and Light Repair IV (MLR IV)
Maintenance and Light Repair IV (MLR IV) Primary Career Cluster: Consultant: Course Code(s): 5882 Transportation, Distribution, & Logistics Rachel Allen, (615) 532-2835, Rachel.Allen@tn.gov Prerequisite(s):
More informationSECTION 23 81 03 - PACKAGED ROOFTOP AIR CONDITIONING UNITS NON-CUSTOM
SECTION 23 81 03 - PACKAGED ROOFTOP AIR CONDITIONING UNITS NON-CUSTOM PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Packaged rooftop air conditioning unit (5 tons and smaller). 2. Roof curb. 1.2
More informationP7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc
P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center
More informationSection 6 - System Diagrams
Section 6 System Diagrams Page 6-1 Section 6 - System Diagrams Section Contents Page Overview...6-3 Flow Diagram, Fuel System...6-4 Flow Diagrams, Lubricating Oil System...6-5 Flow Diagrams, Cooling System...6-8
More informationScheduled Maintenance (North America)
Scheduled Maintenance (North America) Follow Schedule 1 if the vehicle is operated mainly where none of the following conditions apply. f any do apply, follow Schedule 2 (Canada and Puerto Rico residents
More information1 5 05-12 5 05-12. Additions, Revisions, or Updates
5 05-12 1 5 05-12 SUBJECT DATE Cylinder Head May 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0023 EPA04 MBE 4000 Cylinder Head Additional
More informationSTATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE AUTO 220 INTERNAL COMBUSTION ENGINES
STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE AUTO 220 INTERNAL COMBUSTION ENGINES Prepared By: BRANDON BALDWIN CANINO SCHOOL OF ENGINEERING TECHNOLOGY AUTOMOTIVE TECHNOLOGY
More informationFlushing and Cleaning the A/C System
Flushing and Cleaning the A/C System Once an AC system has been contaminated or has suffered a failure, the most important part of the AC service to restore the cooling performance to the system = FLUSHING
More informationMAINTENANCE MANUAL LPG CNG INJECTOR RAIL RAIL TYPE 03
MAINTENANCE MANUAL LPG CNG INJECTOR RAIL RAIL TYPE 03 December 2004 Rev. 01 Tartarini Auto S.p.a Via Bonazzi 43 40013 Castel Maggiore (Bo) Italy Tel.:+39 051 632 24 11 Fax: 051 632 24 00 E-mail: info@tartariniauto.it
More informationMACS Recommended Service Procedures
MACS Recommended Service Procedures Initial Customer Contact It is important to obtain information from the customer identifying the problem and any previous servicing history prior to attempting repair
More informationSeries 53, 71, 92 and 149 Engines
3.5 million two-cycle engines built since 1940 Nearly 500,000 still in operation around the world $100 million in parts inventory to cover your needs Series 53, 71, 92 and 149 Engines Over 2,500 factory
More informationCooling system components, removing and installing
Page 1 of 30 19-1 Cooling system components, removing and installing Notes: When the engine is warm the cooling system is under pressure. If necessary release pressure before commencing repair work. Secure
More informationSection 10 Maintenance Specifications
Page 10-1 Section Contents Page General Engine Data...10-3 Fuel System Specifications...10-3 Lubricating Oil System Specifications...10-4 Cooling System Specifications...10-4 Air Intake System Specifications...10-4
More informationCummins Westport The Natural Choice
Cummins Westport The Natural Choice Driver Tips For Cummins Westport ISL G And ISX12 G Natural Gas Truck And Bus Engines. What You Need To Know About Your Natural Gas Engine. Cummins Westport natural gas
More informationEVERY ROUTE. ISB FOR SCHOOL BUS APPLICATIONS
EVERY ROUTE. TM ISB FOR SCHOOL BUS APPLICATIONS SCHOOL BUS APPLICATIONS. The Cummins ISB is the perfect engine to power your school bus. Reliable, efficient and quiet, the ISB delivers the power you need
More informationAction Plan Template HVAC Page 1
Action Plan Template HVAC Page 1 Once Establish expected HVAC system efficiency - Write down the expected efficiency of HVAC systems to use as a baseline - Add this information to maintenance plan documentation
More information2006 Volkswagen Maintenance Schedule by Miles/Kilometers
2.0 Liter Engine: Engine: Change engine oil and oil filter Engine: Check for leaks Service interval display: Reset (Where applicable) Exhaust system: Check for damage & leaks Battery: Check Door check
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)
17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure
More informationtire inflator with pressure gauge
tire inflator with pressure gauge Model 95583 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks
More informationRegular maintenance of marine diesel engines is key to more uptime and lower life-cycle costs
Marine Regular maintenance of marine diesel engines is key to more uptime and lower life-cycle costs Modern marine diesel engines have a higher power-to-weight ratio, more performance A TOGNUM GROUP BRAND
More informationVehicle Fire Protection. An Ownerʼs Manual for ANSUL Fire Suppression/Detection Systems
Vehicle Fire Protection An Ownerʼs Manual for ANSUL Fire Suppression/Detection Systems 002792 Off-road vehicles do have fires Statistics show that off-road vehicles burn with alarming frequency. These
More informationENGINE COOLING GENERAL DESCRIPTION 11-1
ENGINE COOLING 11-1 GENERAL DESCRIPTION The cooling system of all 1963 Cadillac engines is of the low capacity type. This is made possible by the small cylinder head area exposed to flame and the high
More informationSLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3
PART #50190 SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER
More informationSection 10 Maintenance Specifications
Page 10-1 Section Contents Page General Engine Data...10-3 Fuel System Specifications...10-4 Lubricating Oil System Specifications...10-4 Cooling System Specifications...10-4 Air Intake System Specifications...10-5
More informationOil and Coolant Circulating Heating System. Model - OCSM
Oil and Coolant Circulating Heating System Model - OCSM Installation & Operation Manual 216280-000 REV 2 Identifying Your System The HOTSTART heating system is designed to heat fluids for use in marine
More informationStandard Hydraulic Piping Flushing Procedure
Page 1 of 6 1.0 Scope This procedure covers the minimum technical requirements for cleaning and flushing of Hydraulic and Piping, and related accessories. 2.0 Introduction In hydraulic fluid power systems,
More informationC18 MARINE ENGINE SAFETY.CAT.COM. Maintenance Intervals. Excerpted from Operation & Maintenance Manual (SEBU7689-10)
SAFETY.CAT.COM C18 MARINE ENGINE Maintenance Intervals Excerpted from Operation & Maintenance Manual (SEBU7689-10) 2009 Caterpillar All Rights Reserved SEBU7689-10 81 Maintenance Interval Schedule i03542891
More information6.7L Diesel Fuel System Contamination Diagnosis and Service Procedure Job Aid (Revised March, 2012)
6.7L Diesel Fuel System Contamination Diagnosis and Service Procedure Job Aid (Revised March, 2012) Fuel contamination on 6.7L diesel engines can damage fuel system components including the High Pressure
More information- Service Bulletin - Pistons.
Normal combustion: is smooth and even from the spark plug through the top of the chamber. 1 2 3 Spark occurs Combustion moves smoothly across chamber Combustion and power completed Pre-Ignition: occurs
More informationMAINTENANCE INTERVALS
MAINTENANCE INTERVALS Operation and Maintenance Manual Excerpt 2010 Caterpillar All Rights Reserved SEBU7731-08 July 2007 Operation and Maintenance Manual 216B, 226B, 232B, 236B, 242B, 246B, 248B, 252B,
More informationVOLVO PENTA 2+ 3 FACTORY PROTECTION PROGRAM. A New Generation of Customer Care for Today s New Technology Engines
VOLVO PENTA 2+ 3 FACTORY PROTECTION PROGRAM A New Generation of Customer Care for Today s New Technology Engines A New Generation of Customer Care Volvo Penta provides a factory-backed, factory-administered
More information