INSTALLATION INSTRUCTIONS

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Transcription

1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII ATTACHMENT RIDGELINE Issue Date (EX-L WITH NAVI) FEB 2005 PART LIST Template Attachment Kit P/N: 08B21-SJC-100 Rear camera trim 19 Wire ties Rear camera bracket 9 Small wire ties 6 Wire ties with clip Rear camera subbracket 6-Pin connector Harness clamp bracket A Grommet Harness clamp bracket B 2 Pieces of clear adhesive tape Rear camera subharness 3 Blind nuts 2005 American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 08B21-SJC of 17

2 2 EPT sealers 4 Cushion tapes 2 Socket bolts, 4 x 10 mm 3 Washer screws, 4 x 12 mm 2 Washer screws, 4 x 6 mm 7 Clips TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver 10 mm Combination wrench Ratchet 10, 12 mm and 14 mm Socket Torque wrench File Isopropyl alcohol Shop towel Tape measure Drill 3 mm, 8 mm, and 10 mm Drill bits Utility knife T40, and T50 Torx bit KTC trim tool Scissors Tape Electrical tape Wire 3 mm Hex wrench Illustration of the Rear Camera Installed on the Vehicle Round grommet CONTROL UNIT 6 Oval grommets Rear Camera Kit P/N: 08A57-SJC-100 SUB 6-PIN K Rear camera INSTALLATION Owner s Manual Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 2 of 17 AII (0502) 2005 American Honda Motor Co., Inc - All Rights Reserved.

3 3. Remove the fuel fill door release handle. Remove the left front door sill trim (three clips and three retaining tabs). TAB FUEL FILL DOOR RELEASE HANDLE CLIPS (3) LEFT FRONT DOOR SILL TRIM TAB 5. Pull away the weatherstrip from the B-pillar lower trim panel. Remove the left seat belt lower anchor bolt cover and remove the lower anchor bolt. Remove the left B-pillar lower trim panel by pulling it out toward you as shown. Seat belt anchor bolt torque: 30 to 35 N m (22 to 25 lbs) WEATHERSTRIP (Pull away.) FRONT LEFT B-PILLAR LOWER TRIM PANEL FRONT T 4. Remove the left rear door sill trim (three clips and four retaining tabs). LOWER ANCHOR BOLT COVER LEFT SEAT BELT LOWER ANCHOR BOLT T TAB CLIPS (3) LEFT DOOR SILL TRIM 6. Remove the driver s seat frame rear cover (two clips and two hooks). TAB DRIVER S SEAT FRONT T HOOKS (2) DRIVER S SEAT FRAME COVER CLIPS (2) K 2005 American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 3 of 17

4 7. Lift up the rear seats, and remove the rear underseat trim panel: Remove the right rear under-seat trim panel (four clips). Remove the left rear under-seat trim panel (seven clips). 9. Remove the rear seat belt anchor bolt and eight seat anchor bolts. Seat belt anchor bolt torque: 30 to 35 N m (22 to 25 lbs) RIGHT UNDER-SEAT TRIM PANEL CLIPS (4) CLIPS CLIPS (7) LEFT UNDER-SEAT TRIM COVER T 8. Remove the rear seat bracket covers: Remove the left and right rear seat bracket covers (two clips for each cover). Remove the center seat bracket cover (two clips and nine retaining tabs). SEAT ANCHOR BOLTS (8) 10. Remove the caps from the rear trim panel cover (four retaining tabs for each cover), and remove the rear seat. TABS (4) SEAT BELT ANCHOR BOLT CAP TABS (4) T CAP LEFT SEAT BRACKET COVER CLIP TABS (9) SEAT CENTER SEAT BRACKET COVER T CLIPS (2) RIGHT SEAT BRACKET COVER CLIP T 4 of 17 AII (0502) 2005 American Honda Motor Co., Inc - All Rights Reserved.

5 11. Remove the rear trim panel cover (eight clips and two retaining tabs). TABS (2) TRIM PANEL COVER 14. Remove the left rear lower anchor bolt cover, and remove the left rear seat belt lower anchor bolt: Seat belt anchor bolt torque: 30 to 35 N m (22 to 25 lbs) CLIP CLIPS (6) CLIPS (2) CLIP LEFT SEAT BELT UPPER ANCHOR BOLT TABS (4) CLIP T 12. Remove the left rear seat belt upper anchor bolt cover (four retaining tabs), and remove the left rear seat belt upper anchor bolt: Seat belt anchor bolt torque: 30 to 35 N m (22 to 25 lbs) LEFT LOWER ANCHOR BOLT COVER LEFT SEAT BELT LOWER ANCHOR BOLT 15. Remove the upper clip, then pull the left rear pillar lower trim out toward you to release two clips. 16. Remove the left rear taillight (two bolts, two clips and vehicle connector). Remove the right taillight the same way. LEFT SIDE LEFT PILLAR LOWER TRIM RIGHT SIDE K LEFT SEAT BELT ANCHOR BOLT TABS (2) COVER LEFT PILLAR UPPER TRIM CLIP K BOLT 13. Remove the left rear pillar upper trim: CLIPS (2) With side airbag; pull the clip, and remove the left rear pillar trim by releasing the one clip. Without side airbag; remove the left rear pillar trim by releasing the two clips. LEFT TAILLIGHT H 2005 American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 5 of 17

6 17. Remove the rear bumper: Remove the license plate (two bolts). Remove two bolts, eight self-tapping screws and six clips from the rear bumper. Pull the rear bumper toward you. Unplug the two vehicle connectors, and remove the rear bumper. Set the rear bumper on the blanket. Using a KTC trim tool, carefully pry up the front of the trim to release the three front clips. Start with the left clip and work towards the right clip. Gently lift the front of the trim to release the four rear clips. CLIPS (7) S (2) CLIPS (6) KTC TRIM TOOL RIGHT CLIP (Finish here.) BUMPER BOLTS (2) CLIPS (4) SELF- TAPPING SCREWS (8) LEFT CLIP (Start here.) CENTER CLIP (Second.) 4D19062H LICENSE PLATE BOLT Remove the antenna grommet from the roof, unplug the vehicle connector, and remove the rear roof trim. 18. Remove the rear roof trim: Remove the roof trim nut covers (two retaining tabs for each cover). Remove the two nuts. HOOKS (2) ROOF TRIM ROOF TRIM NUT COVER TABS (2) NUTS (2) HIGH-MOUNT BRAKE LIGHT ANTENNA S (2) H ROOF TRIM 4D19051H 6 of 17 AII (0502) 2005 American Honda Motor Co., Inc - All Rights Reserved.

7 19. Remove and discard the grommets from the roof panel, and install the six oval grommets and one round grommet into the roof panel. (Discard.) ROUND 21. Remove the left bed rail trim: Remove the screw cover (four retaining tabs). Remove the self-tapping screw. Pull the left bed rail trim back to release the six clips, and remove the left bed rail trim. SCREW COVER TABS (4) CLIPS (6) ROOF PANEL LEFT BED RAIL TRIM OVAL S (6) SELF- TAPPING SCREW S (6) (Discard.) 4D20510K LEFT BED RAIL TRIM 20. On the rear roof trim backside, remove and discard the clips from the rear roof trim, and install the seven clips to the rear roof trim. ROOF TRIM 22. Remove the left C-pillar outer trim light (one screw) and unplug the connector. CLIPS (3) (Install.) H CLIPS (7) CLIPS (3) (Remove.) PANEL C-PILLAR OUTER TRIM LEFT C-PILLAR OUTER TRIM CLIPS (7) (Discard.) 4D20501K SELF-TAPPING SCREW 23. Remove the left C-pillar outer trim (slide rearward, and unplug the vehicle connector). Remove the clips from the body, and reinstall the clips to the left C-pillar outer trim American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 7 of 17

8 24. Remove the left front anchor (two torx bolts). 26. Remove the left lower bed light (one self-tapping screw, pull the light out towards you, and unplug the vehicle connector). LEFT FRONT ANCHOR CLIP LEFT LOWER BED LIGHT SELF-TAPPING SCREW T50 TORX BOLT LEFT ANCHOR T50 TORX BOLT H H 27. Remove the left rear anchor (two torx bolts). 25. Remove the front bed panel (six torx bolts). 28. Remove the left side bed panel (six torx bolts). LEFT SIDE BED PANEL FRONT BED PANEL T40 TORX BOLTS (6) H T40 TORX BOLTS (6) H 8 of 17 AII (0502) 2005 American Honda Motor Co., Inc - All Rights Reserved.

9 29. Remove the tailgate trim: Remove the four screws and release the one end clip on each side. Sharply push the tailgate trim to the right to release the 16 clips from the trim. Remove the 16 clips from the tailgate, and reinstall the 16 clips to the tailgate trim in the direction shown. 31. Get the template. Using scissors, cut out the marked area from the template. Align the edge of the template with the edge of the tailgate as shown, and attach it to the tailgate with tape. OUTER CUT TEMPLATE TRIM CLIPS (16) UPPER HANDLE TEMPLATE S (9) CLIPS (2) TRIM SELF-TAPPING SCREWS (4) 30. Remove the tailgate panel (seven torx screws) T CUT AREA 32. Center punch the tailgate at the marks on the template. Remove the template K T40 TORX SCREWS (7) MARKS (4) PANEL UPPER HANDLE CENTER PUNCH CUT TEMPLATE K T 2005 American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 9 of 17

10 33. Drill three 8 mm holes and one 10 mm hole in the tailgate. Wrap tape around a 3 mm drill bit, an 8 mm drill bit and a 10 mm drill bit 10 mm from the end or use a drill stop. While wearing eye protection, drill a 3 mm hole, then an 8 mm hole in all four locations. Drill a 10 mm hole only in the upper center hole. Remove any burrs, and apply touch-up paint to all of the holes. 35. Remove the four screws from the rear camera. Route the rear camera harness through the rear camera subbracket, and install the rear camera subbracket to the rear camera with the four screws. SUBBRACKET 10 mm DRILL BIT DRILL BIT (3 mm 8 mm 10 mm) (Wrap tape around the drill bit.) UPPER CENTER HOLE (10 mm) SCREWS (4) K MARKS (4) K 36. Attach a piece of wire to the terminals on the rear camera harness, and tape the wire to the terminals. DRILL DRILL BIT (3 mm 8 mm) 34. Install one blind nut into each 8 mm hole. TERMINALS K BLIND NUT 8 mm HOLES (3) K WIRE 10 of 17 AII (0502) 2005 American Honda Motor Co., Inc - All Rights Reserved.

11 37. Route the rear camera harness through the 10 mm hole in the tailgate, and seat the grommet into the 10 mm hole. 10 mm HOLE 39. Align the two locating tabs on the rear camera subbracket with the slots in the rear camera bracket, and install two 4 x 6 mm washer-screws. NOTE: Make sure the flat surface of the rear camera subbracket is facing up; otherwise, the camera view will be upside down. 4 x 6 mm WASHER SCREW BRACKET WIRE SLOTS (2) PANEL K 38. Install the rear camera bracket to the three blind nuts with three 4 x 12 mm washer-screws. SUBBRACKET Flat surface facing up. LOCATING TABS (2) 4 x 6 mm WASHER SCREW K BLIND NUT PANEL 4 x 12 mm WASHER SCREW BRACKET K 2005 American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 11 of 17

12 40. Install clear adhesive tape to the tailgate: Open the tailgate. Get the pieces of clear adhesive tape. Using scissors, cut 30 mm from the end of each piece. Using isopropyl alcohol on a shop towel, clean the tailgate where the adhesive tape will attach. 41. Route the rear camera harness along the tailgate as shown K 42. Remove the torx bolt from the tailgate hinge, and attach the harness clamp bracket B to the tailgate using the torx bolt you just removed. Do not tighten the torx bolt at this time. T50 TORX BOLT (Do not tighten at this time.) 30 mm CLAMP BRACKET B CLEAR ADHESIVE HINGE K 30 mm SECOND ADHESIVE CLEAR ADHESIVE LIP FIRST ADHESIVE 4N09043K 12 of 17 AII (0502) 2005 American Honda Motor Co., Inc - All Rights Reserved.

13 43. Secure the rear camera harness to the harness clamp bracket with two small wire ties. Attach the wire tie, over the black tape attached to the harness, where the vinyl cover begins. 46. Pull the rear camera harness out from the inside of the tailgate, and secure the rear camera harness to the harness clamp bracket A with one small wire tie. Attach the wire tie over the black tape attached to the harness. SMALL WIRE TIE (Attach over the black tape.) BLACK T50 TORX BOLT (Torque to 29 to 32 N m) SMALL WIRE TIE CLAMP BRACKET T50 TORX BOLT (Torque to 29 to 32 N m) 44. Torque the T50 torx bolt to 29 to 32 N m (21 to 23 lbs) K 45. Close the tailgate. Remove the lower outboard hinge bolt, and attach harness clamp bracket A to the tailgate hinge with the torx bolt you just removed. Do not tighten the torx bolt at this time. CLAMP BRACKET A BLACK SMALL K WIRE TIE (Attach over the black tape.) 47. Torque the T50 torx bolt to 29 to 32 N m (21 to 23 lbs). 48. Open the tailgate. Using isopropyl alcohol on a shop towel, clean the tailgate where the cushion tapes will attach. Using scissors, cut one cushion tape in half. Secure the rear camera harness to the tailgate with two half cushion tapes and two full cushion tapes at the locations shown. CUSHION K HINGE CLAMP BRACKET A T50 TORX BOLT (Do not tighten at this time.) CUSHION (Cut in half.) 4N09050K 2005 American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 13 of 17

14 49. Secure the rear camera harness to the tailgate with five wire ties with clip. WIRE TIES WITH CLIP (5) 52. Route the rear camera harness out through the bed panel hole, and secure the rear camera harness to the vehicle harness with one wire tie just inside the panel hole. BED PANEL HOLE WIRE TIE FRONT CUSHION Cut in half K 50. Using isopropyl alcohol on a shop towel, clean the tailgate where the cushion tape will attach. Using scissors, cut one cushion tape in half. Secure the rear camera harness to the tailgate with one half cushion tape. 51. Route the rear camera harness through the left side vehicle panel hole, and secure the rear camera harness to the vehicle harness with two wire ties. LEFT SIDE PANEL HOLE LEFT SIDE PANEL K 53. Route the rear camera harness along the vehicle harness towards the front of the vehicle, and secure it to the vehicle harness with six wire ties in the areas shown. WIRE TIES (6) 4N09060K WIRE TIE K 14 of 17 AII (0502) 2005 American Honda Motor Co., Inc - All Rights Reserved.

15 54. Remove the vehicle grommet from the left C-pillar. OPENING LEFT C-PILLAR BED BULKHEAD WIRE 57. Inside the passenger s compartments turn down the rear panel insulator. Pull the rear camera harness out from the hole in the C-pillar, and remove the tape and wire from the rear camera harness. PANEL OPENING FRONT WIRE K 6-PIN Black/ Black Red/ Red Blue/ Black White/ White Yellow/ Yellow Brown Harness side view TERMINALS (6) 6-PIN 6-PIN LOCK K 55. Insert the rear camera harness through the grommet, and route the rear camera harness through the vehicle grommet opening. Seat the grommet into the grommet hole. 56. Using electrical tape, secure the grommet to the rear camera harness. Pay attention to the angle of the grommet. 58. Remove the lock from the 6-pin connector. Plug the rear camera harness terminals into the 6-pin connector as shown. Reinstall the lock. 59. Get the rear camera subharness. Plug the rear camera subharness 6-pin connector into the rear camera harness 6-pin connector, and secure the connected 6-pin connectors to the vehicle connectors with two wire ties. WIRE TIE 6-PIN C-PILLAR UP WIRE TIES (2) FRONT SUB 6-PIN OPENING DOWN K SUB WIRE TIE K 60. Route the rear camera subharness forward along the vehicle harness, and secure the subharness to the vehicle harness with five wire ties American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 15 of 17

16 61. Continue routing the rear camera subharness forward along the vehicle harness, and secure the subharness to the vehicle harness with four small wire ties. DRIVER S SEAT 63. Plug the rear camera subharness 6-pin connector into the Navi control unit. NAVI CONTROL UNIT SUB FRONT SUB 6-PIN K SMALL WIRE TIE K 62. Route the rear camera subharness along the vehicle harness and under the floor carpet, then pull the rear camera subharness out from under the floor carpet opening (under the driver s seat). Secure the rear camera subharness to the vehicle harness with two wire ties. 64. Slide the driver s seat back and forth to check that the rear camera subharness is not pulled too tight or is too loose. Check that the rear camera subharness is not pulled too tight when the seat is moved back and forth. DRIVER S SEAT FLOOR CARPET OPENING DRIVER S SEAT K WIRE TIE SUB 4N10010K 16 of 17 AII (0502) 2005 American Honda Motor Co., Inc - All Rights Reserved.

17 65. Reconnect the negative cable to the battery. Turn the key to the ON position, and enter the Navi code. 66. Move the shift knob to the R position. 67. Adjust the angle of the rear camera while watching the navigation monitor. When you are satisfied with the camera angle, install the rear camera trim to the rear camera bracket with two 4 x 10 mm socket bolts. 69. Measure and mark the rear bumper at the location shown. BUMPER Adjust the angle. 15 mm 10 mm TRIM 3 mm Cut off. 4N15011K 4 x 10 mm SOCKET BOLT 68. Turn the key to the off position. BRACKET K 70. Using a utility knife, cut and remove the measured piece from the rear bumper. Remove any burrs from the cut area with a file. 71. Reinstall the rear bumper. 72. Check that all wire harnesses are routed properly and all connectors are plugged in. 73. Enter the customer s radio anti-theft code, and reset the radio station presets. 74. Set the clock. 75. Check the operation of the rear camera according to the owner s manual provided. 76. Put the rear camera Owner s Manual in the glove box with the vehicle owner s manual. 77. Reinstall all removed parts American Honda Motor Co., Inc - All Rights Reserved. AII (0502) 17 of 17

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM 2003 ACCORD 4 DOOR AII 24378 Issue Date MARCH 2003 The XM Radio will not fit in a vehicle equipped with a rear entertainment

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH CR-V Application Publications No. AII 12095 Issue Date DEC 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-T0A-100 Hex nut, 12 mm Trailer hitch Hitch pin Hitch

More information

INSTALLATION INSTRUCTIONS www.collegehillshonda.com Accessory USB ADAPTER Application 2009 FIT (BASE MODEL) Publications No. AII 39879 Issue Date SEP 2008 PARTS LIST USB Adapter Attachment Kit P/N 08B28-TK6-100

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S P/N 08V31-SWA-100 Application CR-V Publications No. AII 32952-35942 Issue Date APRIL 2007 PARTS LIST Right fog light Switch Relay Left fog light Bracket Fog light

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SVA-100A 2007 CIVIC SI All 33486 Issue Date AUG 2006 PARTS LIST Right fog light 5 Wire ties Left fog light Clip Right bracket

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 24393 ACCORD (DX, LX) SYSTEM 2-AND 4-DOOR Issue Date AUG 2002 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS FOG LAMP ATTACHMENT P/N 08V70-MJR-640 GL1800C MII Issue Date January 2014 PARTS LIST No. Description Qty ((( Right bracket 1 (1) (2) (((

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24087 2003 ACCORD 2-DOOR Issue Date SEP 2002 PARTS LIST P/N 08U97-SDN-110 (Birdseye) P/N 08U97-SDN-110A (Burlwood) P/N 08U97-SDN-110B

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. INSTALLATION INSTRUCTIONS S 2005 CIVIC HYBRID AII 28002 Issue Date SEP 2004 PARTS LIST 33 Wire ties Fog Lights (sold separately): P/N 08V31-S5D-102A Left fog light

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 37369 WHEEL 2008 TL Issue Date JUN 2007 PARTS LIST 1. Make sure you have the anti-theft code for the radio, then write down the frequencies

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. PASSENGER ARMREST P/N 08R32-MCA-100 GL1800 Honda Dealer: Please give a copy of these instructions to your customer. MII 11185 Issue Date

More information

TOYOTA RAV4 2006 - TRAILER WIRE HARNESS Section I Installation Preparation

TOYOTA RAV4 2006 - TRAILER WIRE HARNESS Section I Installation Preparation Section I Installation Preparation Part Number: 08921-42900 Kit Contents Item # Quantity Reqd. Description 1 1 Converter 2 1 Wire harness 3 1 Sub wire harness No.1 4 2 Plastic Tie (300mm) 5 21 Plastic

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. INSTALLATION INSTRUCTIONS HEATED GRIP WITH THERMOSTAT P/N 08T50-MCA-102 GL1800 Honda Dealer: Please give a copy of these instructions to your customer. Issue Date

More information

Polaris Slingshot Trailer Hitch Installation Instructions #PSS007

Polaris Slingshot Trailer Hitch Installation Instructions #PSS007 Polaris Slingshot Trailer Hitch Installation Instructions #PSS007 1. Lay out and familiarize yourself with the components and hardware supplied with the hitch. Note the included trailer wiring isolator

More information

TOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation

TOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,

More information

Form #5327, Rev. RTP, 03-28-12. Honda Civic DRL KIT 2011-UP Part Number: 260-1022-HN2

Form #5327, Rev. RTP, 03-28-12. Honda Civic DRL KIT 2011-UP Part Number: 260-1022-HN2 Form #5327, Rev. RTP, 03-28-12 Honda Civic DRL KIT 2011-UP Kit Contents Item # Qty. Description 1 1 Controller 2 2 DRLs 3 2 Bezels L, R 4 1 DRL Extension 5 1 Ignition Harness 6 1 Illumination 7 1 Ground

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS [1] Description: Tow Hitch Wire Harness Kit [2] Application: Nissan Rogue Note: Tow Harness application is limited to specific vehicle option packages that include tow harness

More information

TOYOTA TACOMA 2012 - TRAILER WIRE HARNESS Preparation

TOYOTA TACOMA 2012 - TRAILER WIRE HARNESS Preparation Preparation Part Number: PT725-35120 Kit Contents Item # Quantity Reqd. Description 1 1 Flasher Assembly (F/A) 2 1 Wire Harness 3 1 Sub Wire Harness 4 2 Plastic Tie (300mm) 5 4 Plastic Tie (200mm) 6 13

More information

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware

More information

Mazda MX-5 Soft Top Installation Instructions

Mazda MX-5 Soft Top Installation Instructions Mazda MX-5 Soft Top Installation Instructions These instructions show how to replace your soft top with the frame remaining attached to the car. This requires the use of a right angled driver which is

More information

TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation

TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation Part Number: PT297-35061 Kit Contents Item # Quantity Reqd. Description 1 2 Driving Lamp Assembly 2 1 Switch Harness 3 1 Lamp Harness 4 2 Stone Shield

More information

Installation Instructions

Installation Instructions Installation Instructions Page 1 of 16 January 2008 Equipment Parts, Trailer Hitch Ver 3.0 Accessory Development SUBJECT TRAILER HITCH KIT (US Only) - P/N 71 60 0 413 359 MODEL X5 (E70): Select Vehicle

More information

INSTALLATION MANUAL INSIDE PASSENGER COMPARTMENT. HFC 134a FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH

INSTALLATION MANUAL INSIDE PASSENGER COMPARTMENT. HFC 134a FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH HFC 134a Ozone Friendly Refrigerant FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH AAAMU-60 / INSIDE PASSENGER COMPARTMENT INSTALLATION MANUAL 2000 (EUROPE) B.V.. All Rights Reserved. This

More information

Installation instruction do88 Intercooler for Volvo S40 / V50 / C30

Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At

More information

TOOL SERVICE PARTS SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL EXTRACTION TOOL GENERAL APPLICABILITY

TOOL SERVICE PARTS SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL EXTRACTION TOOL GENERAL APPLICABILITY TOYOTA COROLLA,MATRIX,TACOMA,TUNDRA,PRIUS,YARIS PONITIAC VIBE PART NUMBER: 250-1731 TOOL SERVICE PARTS CRUISE CONTROL KIT 1 1 2 BASE KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CONTROL SWITCH ASSEMBLY 1 2 SCREWS

More information

Installing RNS-E SAT NAV for Audi A4

Installing RNS-E SAT NAV for Audi A4 As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost

More information

Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006

Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering

More information

CONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation

CONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER

More information

INSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL

INSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL PREMIUM FRONT BUMPER AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL 2012 3 0026032.0 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND

More information

2012-2014 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: 4 x 1/4 washers Wax & Grease Remover

2012-2014 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: 4 x 1/4 washers Wax & Grease Remover 2012-2014 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Bumper Ratchet, 10mm, 14mm & 19mm sockets 2 x Slider Plates

More information

P150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813

P150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813 P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6

More information

INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5100 for use with R1100RT and R1150RT

INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5100 for use with R1100RT and R1150RT INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5100 for use with R1100RT and R1150RT Read these instructions carefully and thoroughly before beginning work. Before installing the accessory,

More information

COMPONENTS IP 2 INSTRUMENT PANEL INSTRUMENT PANEL ASSEMBLY ASSIST GRIP RETAINER RH FRONT PILLAR GARNISH RH FRONT DOOR OPENING TRIM WEATHERSTRIP RH

COMPONENTS IP 2 INSTRUMENT PANEL INSTRUMENT PANEL ASSEMBLY ASSIST GRIP RETAINER RH FRONT PILLAR GARNISH RH FRONT DOOR OPENING TRIM WEATHERSTRIP RH INSTRUMENT PANEL INSTRUMENT PANEL INSTRUMENT PANEL PRECAUTION 1 1. PRECAUTION FOR VEHICLE WITH SRS AIRBAG AND SEAT BELT PRETENSIONER (a) Some of these operations may affect the SRS airbag system. Read

More information

Post Mount Light Installation*

Post Mount Light Installation* Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service

More information

Time needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.

Time needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk. DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage

More information

Extendable Trailer Towing Mirror

Extendable Trailer Towing Mirror Extendable Trailer Towing Mirror Installation Instructions For: 1997-2001 Ford F150 CIPA Part Numbers 72000 & 82000 WARNING Manufacturer recommends this installation be carried out by a professional installer

More information

INSTALLATION INSTRUCTIONS ELEVATION REAR BUMPER RAM

INSTALLATION INSTRUCTIONS ELEVATION REAR BUMPER RAM INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 4 8mm x 40mm Hex Bolts 1 Universal License Plate Light 4 8mm x 28mm x 3mm Flat Washers 8 12-1.75mm x 50mm Hex Bolts 4 8mm Lock Washers

More information

TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation

TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

Installation instructions, accessories - Handsfree, Volvo Handsfree System with Bluetooth

Installation instructions, accessories - Handsfree, Volvo Handsfree System with Bluetooth XC90 Section Group Weight(Kg/Pounds) Year Month 3 394 1/2.2 2007 11 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2007, XC90 2008, XC90 2008, XC90 2009, XC90 2010 Replaces issue: 2006 05

More information

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger

More information

C5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions

C5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions C5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions Ok, let's start with taking the radio bezel dash area off first. Here is what the OEM radio looks like... First you flip

More information

TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation

TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

WARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE

WARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8

More information

Cut zip ties and remove 2 plastic wiring harness brackets.

Cut zip ties and remove 2 plastic wiring harness brackets. TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports

More information

TOOL SVC NUMBERS: 250-2598, 250-2600 SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL 250-2598 2 1 EXTRACTION TOOL/PART# 250-2600

TOOL SVC NUMBERS: 250-2598, 250-2600 SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL 250-2598 2 1 EXTRACTION TOOL/PART# 250-2600 07-08 TOYOTA FJ CRUISER, 05-09 SIENNA, 06-08 SCION TC PART NUMBER: 250-1732 1 CRUISE CONTROL KIT TOOL SVC NUMBERS: 250-2598, 250-2600 2 2 1 BASE KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CONTROL SWITCH ASSEMBLY

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure

More information

Fresenius Medical Care North America Service Bulletin

Fresenius Medical Care North America Service Bulletin Fresenius Medical Care North America Service Bulletin Equipment: Bulletin: Subject: 2008 K Hemodialysis Machines 15-FRK-001 Rev A Optional Shunt Box Ferrite Core Installation (Update) 1.0 PURPOSE To inform

More information

** T23 * R PART NUMBER INSTALLATION INSTRUCTIONS FOR TOYOTA NAVIGATION SYSTEM NAVIGATION KIT PART N Manual Ref. Nr.

** T23 * R PART NUMBER INSTALLATION INSTRUCTIONS FOR TOYOTA NAVIGATION SYSTEM NAVIGATION KIT PART N Manual Ref. Nr. TOYOTA NAVIGATION SYSTEM INSTALLATION INSTRUCTIONS FOR ** T2 * R PART NUMBER NAVIGATION KIT PART N 08545-0080 Manual Ref. Nr.N1RT2-0-00 TOYOTA MOTOR CORPORATION PRECAUTIONS PLEASE READ THOROUGHLY THESE

More information

Installation Manual for the Rockmeister Roof Ladder Exclusively for Mercedes-Benz Geländewagen W460, W461 & W463 with single rear door

Installation Manual for the Rockmeister Roof Ladder Exclusively for Mercedes-Benz Geländewagen W460, W461 & W463 with single rear door Installation Manual for the Rockmeister Roof Ladder Exclusively for Mercedes-Benz Geländewagen W460, W461 & W463 with single rear door NOTE: W460 & W461 models have a different Frame Bracket than the W463.

More information

Headlight Removal & Installation: BMW E46

Headlight Removal & Installation: BMW E46 Headlight Removal & Installation: BMW E46 DISCLAIMER Buyer assumes any and all risk and liability from the installation and use of this product. Seller, author, or any of their affiliates assume no liability

More information

KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER

KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING

More information

STEALTH. The MOST Versatile and Easiest To Use Towed Vehicle Braking System available! INSTALLATION MANUAL

STEALTH. The MOST Versatile and Easiest To Use Towed Vehicle Braking System available! INSTALLATION MANUAL 90 STEALTH The MOST Versatile and Easiest To Use Towed Vehicle Braking System available! PROFESSIONAL INSTALLERS: Please return these instructions to the owner, for the owner s future reference INSTALLATION

More information

MGB Chrome Bumper Conversion

MGB Chrome Bumper Conversion MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different

More information

Lincoln Mark VII Power Window Motor Repair

Lincoln Mark VII Power Window Motor Repair Lincoln Mark VII Power Window Motor Repair Is your door no longer going up and down? Does the window motor make a horrible sound when in use? Does your window no longer work at all? You may need to replace

More information

Trailblazer, Envoy, Rainier, Ascender

Trailblazer, Envoy, Rainier, Ascender 6. After removing the trim plate bezel simply remove the four ¼ screws holding the instrument cluster in place. Pull the cluster out and unplug the single wiring harness connection in the back. Trailblazer,

More information

Installation instructions, accessories - Handsfree for cellular phone, system B, entry level

Installation instructions, accessories - Handsfree for cellular phone, system B, entry level XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18

More information

Bushtec Trailer Hitch for BMW R 1200 RT Installation Instructions READ ALL INSTRUCTIONS BEFORE YOU START

Bushtec Trailer Hitch for BMW R 1200 RT Installation Instructions READ ALL INSTRUCTIONS BEFORE YOU START Bushtec Trailer Hitch for BMW R 1200 RT Installation Instructions READ ALL INSTRUCTIONS BEFORE YOU START ATTENTION INSTALLER: THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER!!! BMW Motorrad USA, BMW North

More information

TOYOTA TUNDRA 2015 Billet Grille w/led DRL

TOYOTA TUNDRA 2015 Billet Grille w/led DRL TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3

More information

REAR BUMPER INSTALLATION INSTRUCTIONS TOYOTA TACOMA 05-10 (WITH STOCK HITCH)

REAR BUMPER INSTALLATION INSTRUCTIONS TOYOTA TACOMA 05-10 (WITH STOCK HITCH) Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 REAR BUMPER INSTALLATION INSTRUCTIONS TOYOTA TACOMA 05-10 (WITH STOCK HITCH) Please read before beginning Stainless steel hardware

More information

Installation instructions, accessories - Navigation system, RTI

Installation instructions, accessories - Navigation system, RTI XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 4/8.8 2007 08 Page 1 of 20 Required tools A0000162 IMG-239667 IMG-239664 IMG-239980 IMG-242205 R8802817 R3905015 Page 2 of 20 R3903812 IMG-213320 Page

More information

Here I Will Explain How To Install Recon Cab Lights In A 3rd Gen Dodge Ram.

Here I Will Explain How To Install Recon Cab Lights In A 3rd Gen Dodge Ram. 1 P age Here I Will Explain How To Install Recon Cab Lights In A 3rd Gen Dodge Ram. *Now, There Are Many Ways of Installing Them, Including Wiring Methods, Wiring Connectors, And Other Variables - In This

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-644) Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon, Chevrolet Silverado, GMC Sierra 2000 05 General Tech Tips: Use painter s tape rather than

More information

Installation Instruction and Owners Manual BLASTER SALT/SAND SPREADERS MOUNTING SYSTEMS for Models: 750 & 750S

Installation Instruction and Owners Manual BLASTER SALT/SAND SPREADERS MOUNTING SYSTEMS for Models: 750 & 750S Form - R October 0 Installation Instruction and Owners Manual BLASTER SALT/SAND SPREADERS MOUNTING SYSTEMS for Models: 0 & 0S Meyer Products LLC reserves the right, under its continuing product improvement

More information

2003 ACCORD - Automatic Transmission Removal

2003 ACCORD - Automatic Transmission Removal 2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special

More information

SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V

SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V INSTALLATION GUIDE for the SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly mounted to the

More information

POWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents

POWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents -J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English

More information

SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM SEAT BELT SEAT BELT WARNING SYSTEM SEAT BELT WARNING SYSTEM RESTRAINTS BELT PARTS LOCATION 1 COMBINATION METER ASSEMBLY DRIVER SEAT BELT WARNING LIGHT PASSENGER SEAT BELT WARNING LIGHT DRIVER SIDE JUNCTION

More information

Chevrolet 1500 SAFETY

Chevrolet 1500 SAFETY 2007-2013 Chevrolet 1500 REAR BUMPER INSTALLATION INSTRUCTIONS SAFETY Know safety, no injury. Know injury, no safety. ~Author Unknown READ ALL SAFETY INSTRUCTIONS BEFORE INSTALLATION o o o o o FOLLOW ALL

More information

Before installation it is important to know what parts you have and what the capabilities of these parts are.

Before installation it is important to know what parts you have and what the capabilities of these parts are. INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With

More information

69-26. Airbag. Special tools. VAS 5094 Airbag adapter

69-26. Airbag. Special tools. VAS 5094 Airbag adapter 69-26 Airbag Special tools VAS 5094 Airbag adapter 69-27 Airbag system component locations (Jetta) 1 - Airbag unit driver's side (with Airbag igniter, driver's side -N95) Removing Page 69-36 2 - Airbag

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic

More information

Aluminum Trailer Kit Assembly Overview

Aluminum Trailer Kit Assembly Overview Aluminum Trailer Kit Assembly Overview VERY IMPORTANT: ALWAYS REFER TO YOUR OWNER S MANUAL FOR PROPER OPERATING AND SAFETY INFORMATION REGARDING YOUR TRAILER & PARTS LIST. Step 1: Remove All Parts Remove

More information

Model A Turn Signal Kit Installation Guide

Model A Turn Signal Kit Installation Guide Model A Turn Signal Kit Installation Guide Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/G 2003 3407 Hwy. 120 Duluth, GA 30096, USA Logo Lites and the

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual

More information

Mul$media Interface Installa$on Guide BMW 3- series 2006-2008 with idrive

Mul$media Interface Installa$on Guide BMW 3- series 2006-2008 with idrive Mul$media Interface Installa$on Guide BMW 3- series 2006-2008 with idrive WARNING: All func.ons of this mul.media kit should only be used while exercising cau.on and responsibility. We hold NO responsibility

More information

A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS

A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.

More information

Installation Instructions

Installation Instructions Installation Instructions For Use with PXPV230, PXPV265, PXPD230, and PXPD265 models Attention! - Please read these instructions completely before attempting installation. Always unplug the power supply

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46) 46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel

More information

RECOMMENDED SEQUENCE OF APPLICATION

RECOMMENDED SEQUENCE OF APPLICATION INSTALLATION INSTRUCTIONS (09-12) DODGE RAM PART #250-8408/C (13-CURRENT) DODGE RAM PART #250-8407/C *REQUIRES CHRYSLER/DODGE DEALER ACTIVATION KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE ADAPTER HARNESS

More information

Installation Instructions Avalanche XUV Cap IMPORTANT! IMPORTANT!

Installation Instructions Avalanche XUV Cap IMPORTANT! IMPORTANT! Installation Instructions Avalanche XUV Cap IMPORTANT! Read all instructions carefully before commencing any work. Always wear safety equipment. Some installation steps will require two or more installers.

More information

2003/2004/2005 TOYOTA COROLLA

2003/2004/2005 TOYOTA COROLLA 2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have

More information

Part Number: TCA-715. Hardware Bag Contents. General Applicability SE and LE MODELS. Conflicts - XSE and XLE

Part Number: TCA-715. Hardware Bag Contents. General Applicability SE and LE MODELS. Conflicts - XSE and XLE Date: 03.11.2015 TOYOTA CAMRY 2015 - LED DRL w/turn signal Part Number: TCA-715 Kit Contents Item # Quantity Reqd. Description 1 2 DRL housings w/integrated turn singal 2 1 Harness bag 3 1 User s card

More information

Installation Instructions Kit, Base Rail Bracket Part # 31404

Installation Instructions Kit, Base Rail Bracket Part # 31404 Installation Instructions Kit, Base Rail Bracket Part # 31404 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions. provide important operating and

More information

5 Mechanisms and accessories

5 Mechanisms and accessories 5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR EQUIPMENT 57A INTERIOR EQUIPMENT X79 NOVEMBER 2009

More information

Convertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995)

Convertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995) Convertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995) Written by Samit Ghosh with picture material from vexed of benzworld.org

More information

2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT

2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT 14385 Veterans Way Moreno Valley, CA 92553 Phone: (951) 571-0212 Fax: (951) 571-0215 WWW.CSTSUSPENSION.COM 2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT READ THE FOLLOWING NOTES PRIOR

More information

- power windows - alarm system - electric door mirror control - door warning light - central locking - seat memory

- power windows - alarm system - electric door mirror control - door warning light - central locking - seat memory Door Wiring Harness Plug Connections Binder -, Electrics Vehicle Type: (86) Model Year: 7 (V) Concern: Door wiring harness plug connections X11 / X12. Information: The rubber boot for the door connector

More information

INSTALLATION GUIDE. APPLICATION LENGTH MODEL YR PART # Bestop PART #

INSTALLATION GUIDE. APPLICATION LENGTH MODEL YR PART # Bestop PART # INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Bestop PART # Ford Super Duty F-250 / F-350 Regular Cab (48 ) 1999 2007 10-02513-24 75102-01 Ford Super Duty F-250 / F-350 Super Cab (60 ) 1999 2007

More information

BACKUP CAMERA JEEP COMMANDER/GRAND CHEROKEE

BACKUP CAMERA JEEP COMMANDER/GRAND CHEROKEE BACKUP CAMERA 1 JEEP COMMANDER/GRAND CHEROKEE 2 Call Out Description Parts Quantity 1 Tie Wrap-Nylon 6.9" Supplied in kit 12 2 Camera, Rear View Supplied in kit 1 3 Camera Extension Harness Connector Supplied

More information

Items Required For Installation Small screw driver Straight O-ring pick Coat hanger or welding rod Electrical Tape

Items Required For Installation Small screw driver Straight O-ring pick Coat hanger or welding rod Electrical Tape J u i c e d H y b r i d s T o y o t a P r i u s 2 0 1 2-2 0 1 3 F o g L i g h t K i t ¼ ratchet ¼ X 6 extension ¼ 10mm shallow socket Philips screw driver Items Required For Installation Small screw driver

More information

R O A D M A S T E R, I N C.

R O A D M A S T E R, I N C. R O A D M A S T E R, I N C. ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 6 13 11 MOUNTING BRACKET KIT Cable Tab 14 12 7 15 9 Cable Tab 360-896-0407 fax 360-735-9300 www.roadmasterinc.com ITEM

More information