LCG Series. Specifications. Stroke length. Linear slide cylinder Double acting single rod type. Bore size: 6, 8, 12, 16, 20, 25.

Transcription

1 Linear slide cylinder Double acting single rod type Bore size: 6, 8, 2, 6, 20, 25 JIS symbol Specifications Descriptions LCG Bore size mm Actuation Working fluid Double acting Compressed air Max. working pressure MPa 0.7 Min. working pressure MPa 0.5 (Note ) Withstanding pressure MPa Ambient temperature -0 to 60 (no freezing) (Note 2) Port size Body side surface M3 M5 Rc/8 Rear body M3 M5 Rc/8 Stroke tolerance mm (Note 3) 0 Working piston speed mm/s 50 to 500 (Note 4) Cushion Rubber cushioned Lubrication Not required (when lubricating, use turbine oil Class ISOG 32) Allowable energy absorption J Refer to the table 3 on Page 752. Note : 0.2MPa when using shock absorber type stopper with 6 mm diameter. Note 2: For 6 mm bore cylinder, when using switches, max. ambient temperature is 50 (45 when installing on an iron plate). Note 3: When not using a stopper, a slight gap may exist between the end plate and floating bushing. Note 4: Use the stopper for adjusting the stroke between 50 and 200 mm/s. Stroke length Bore size (mm) Standard stroke length (mm) 6 0, 20, 30, 40, , 20, 30, 40, 50, , 20, 30, 40, 50, 75, , 20, 30, 40, 50, 75, 00, , 20, 30, 40, 50, 75, 00, 25, , 20, 30, 40, 50, 75, 00, 25, 50 Note: Stroke length other than above is not available. 706

2 Specifications Switch specifications color/2 color indicator Descriptions Applications Proximity 2-wire Proximity 3-wire Proximity 2-wire Proximity 3-wire T2H/T2 T2WH/T2W T3H/T3 T3WH/T3W F2H/F2 F2YH/F2Y F3H/F3 F3YH/F3Y Programmable controller Programmable controller, relay Programmable controller Programmable controller, relay Output method - NPN output - NPN output Power voltage - 0 to 28 DC - 0 to 28 DC Load voltage 0 to 30 DC 24 DC 0% 30 DC or less 0 to 30 DC 24 DC 0% 30 DC or less Load current 5 to 20 ma 00 ma or less 50 ma or less 5 to 20 ma 50 ma or less Light Descriptions Applications LED (ON lighting) T0H/T0 Programmable controller, relay * The T0/T5 switch can be used with 220 AC. Consult with for working conditions. Reed 2 wire Red/green LED (ON lighting) LED (ON lighting) T5H/T5 Programmable controller, relay, IC circuit (w/o light), serial connection Load voltage 2/24 DC 0 AC 5/2/24 DC 0 AC Load current 5 to 50 ma 7 to 20 ma 50 ma or less 20 ma or less Light Leakage current LED (ON lighting) 0 ma Without indicator light Red/green LED (ON lighting) LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Leakage current ma or less 0 A or less ma or less 0 A or less Red/green LED (ON lighting) Cylinder weight Basic type (Unit: g) Bore size Basic type stroke length (mm) (mm) ,220,40,620-20,260,260,260,380,500,20 2,20 2,50 2, ,070 2,070 2,070 2,230 2,430 3,240 3,660 4,080 4,530 Additional variation/option (stopper) (Unit: g) Bore size Option, stopper symbol (mm) S to S4 S5/S6 A to A4 A5/A Linear slide cylinder Combined functions 707

3 How to order Without switch LCG With switch Model no. 8 A Bore size 40 B Stroke length Note on model no. selection Note : When changing adjustable stroke range, use a discrete stopper for adjustable stroke listed on page 7. Note 2: When using shock absorber type, refer to K in the stopper dimensions table on page 726. Note 3: Refer to stopper dimensions on page 726 for port positions. Note 4: When no stopper, port position of standard type are as following Fig. and. Note 5: The stopper for adjustable stroke and shock absorber stopper combination is available as a custom order. Note 6: Selectable only when using a stopper. Note 7: Refer to the selection table on Page 70 for combinations of options. Note 8: For 6 to 8 cylinders with 0mm stroke or 2 to 25 cylinders with 20mm stroke or less, custom order is applied because A**, A2**, A5** and A6** can not be adjusted by a standard stopper. Note : For 6 to 8 and 30mm stroke or less cylinder with S*** or A*** switch, when two switches will be installed, select F*H type switch. <Example of model number> LCG-2-40-F2H-R-ADT Model: Linear slide cylinder double acting single rod type LCG A Bore size : 2 B Stroke length : 40 mm C Switch model no. : Proximity, 2-wire Axial lead wire D Switch quantity : One on rod end E Other options : Shock absorber type Stopper position Side surface and bottom side ports presence Material and alloy steel (nitriding) 708 S5 LCG 2 40 F2H* R ADT D Switch quantity C Switch model no. E Option Stopper position Symbol A Bore size B Stroke length (mm) Descriptions C Switch model no. Axial lead Radial lead Contact Indicator Lead wire wire wire F2H* F2* color 2-wire F3H* F3* indicator type 3-wire F2YH* F2Y* 2 color 2-wire F3YH* F3Y* indicator type 3-wire T0H* T0* color Reed T5H* T5* indicator type 2-wire T2H* T2* color 2-wire T3H* T3* indicator type 3-wire T2WH* T2W* 2 color 2-wire T3WH* T3W* indicator type 3-wire *Lead wire length Blank m (standard) 3 3 m (option) 5 5 m (option) Proximity Proximity D Switch quantity R One on rod end H One on head end D Two Bore size ( ) Bore size E Option Blank No option S Stopper for adjustable stroke Adjustable stroke single 5mm Note, Note 5, Note 7 S** Stopper position (changeable to ) S2** Stopper position (changeable to ) S3** Stopper position (changeable to ) S4** Stopper position (changeable to ) S5** Stopper position, S6** Stopper position, A Shock absorber type stopper Note 2, Note 5, Note 7 A** Stopper position (changeable to ) A2** Stopper position (changeable to ) A3** Stopper position (changeable to ) A4** Stopper position (changeable to ) A5** Stopper position, A6** Stopper position, ** section Blank Port at stopper section: no port D Port at stopper section: side surface and bottom side ports presence Note 3, Note 6 Blank Stopper block material: Rolled steel T Stopper block material: Alloy steel (nitriding) Note 6 Stopper installation position Stopper installation position

4 LCG double acting single rod type selection table (Combinations of stopper for adjustable stroke and shock absorber type stopper) LCG Model no. symbol How to order : Combination possible -: Combination not available Option symbol Stopper for adjustable stroke Shock absorber type stopper Bore size Stroke length S S2 S3 S4 S5 S6 A A2 A3 A4 A5 A6 6, 8 2 to and over 0 to and over The option symbol D: with stopper section port and T stopper block alloy steel (nitriding) combination follows the combination table above. Linear slide cylinder Combined functions 70

5 How to order switch For 6 to 2 For 6 to 25 SW F2H SW T2H3 Switch model no. (Page 708 section C ) Switch model no. (Page 708 section C ) How to order stopper set Stopper section and stopper for adjustable stroke or shock absorber stopper set Use when changing from standard to stopper for adjustable stroke or with shock absorber stopper LCG 2 S 2 D Bore size (Page 708 section A ) A B Stopper type S Stopper for adjustable stroke A Shock absorber type stopper Stopper installation position Stopper position or 2 Stopper position or C Port at stopper section Blank No port D Side surface and bottom port presence Precautions for ordering stopper set S 0 i s i n c l u d e d i n t h e s t o p p e r f o r adjustable stroke parts for the stopper for adjustable stroke set. Only when installed on installation position (), (2) (refer to page 708), add the right part according to stroke length and adjustable stroke length. Model no. symbol - : not available Option symbol Discrete stopper for adjustable stroke Adjustable stroke length (mm) Bore size Stroke length , 8 0 S and over Additional not required S02-0 S to S02 S03-30 and over Additional not required S02 S03 70

6 How to order How to order the discrete stopper for adjustable stroke Hexagon socket head set screw with urethane Used when changing the adjustable stroke range or setting custom stroke length LCG 2 S02 Cautions when purchasing discrete stopper O n l y w h e n i n s t a l l i n g a s t o p p e r f o r adjustable stroke or a shock absorber type stopper on installation position () or (2) (refer to page 708), the right combination may be applied depending on stroke length and adjustable stroke length. Bore size (Page 708 section A ) Model no. symbol -S, S2, S5, S6 -A, A2, A5, A6 A Adjustable stroke range S0 S02 Single 5mm (standard) Single 5mm S03 Single 25mm Indicate S0, S02, S03 for A. Note: S03 is not available for 6, 8. Depending on the type, the incompatible models or adjustable stroke ranges may differ from the above values. - : Not available Discrete stopper for adjustable stroke Discrete shock Option symbol Adjustable stroke length (mm) absorber type Bore size Stroke length stopper 0 S , 8 20 and over S0 S02 - A0 0 S to 20 S02 S and over S0 S02 S03 A0 How to order the discrete shock absorber stopper Shock absorber and stopper cap set Used when changing from stopper for adjustable stroke to shock absorber type stopper LCG 2 A0 Shock absorber Stopper cap Bore size (Page 708 section A ) Note: Some models may not be available depending on the type. Refer to Page 708. Refer to page 726 for the stroke adjustment range of the shock absorber type stopper. Applicable shock absorber model No. Model Shock absorber model no. LCG-6 NCK LCG-8 NCK LCG-2 NCK LCG-6 NCK LCG-20 NCK LCG-25 NCK Discrete stopper block model no. display Use when changing from standard to stopper for adjustable stroke or with shock absorber stopper LCG 2 SB Bore size (Page 708 section A ) T A Stopper block SB 6, 8: 30 stroke or less 2 to 25: 50 stroke or less SB2 6, 8: 40 stroke and over 2 to 25: 75 stroke and over Linear slide cylinder Combined functions B Material Blank T Stopper block material: Rolled steel Stopper block material: Alloy steel (nitriding) 7

7 Dimensions (bore size: 6) LCG-6 Stroke length: 0, 20, 30 (The main body fixing holes in this drawing is for 20 mm stroke) RD 2-M3 depth 3 Piping port C K D F 2 H depth W A 2-main body fixing hole (refer to the A-A' cross section) M3 depth 4 Common port (Plug) D 6 8 A L2 L depth R.5 D, E oval hole section dimension C K D F 2 H M3 depth x 2-M3 depth 3 2-M2.6 depth M2.6 depth M3 depth M4 depth depth 3 20 E 2 A - A' cross section 5 Y depth 3 Stroke length L L W Y RD

8 Dimensions (bore size: 6) Dimensions LCG-6 Stroke length: 40, 50 (The main body fixing holes in this drawing is for 50 mm stroke) depth 3 n-main body fixing hole (refer to the A - A' cross section) W D 6 25 P = 20 P x (n - ) 8 L2 L 4 x 2-M3 depth M2.6 depth M3 depth 3 F2H depth 3 P x (n - ) P = 20 E 5 Y depth 3 Stroke length L 6 06 L n W Y RD Linear slide cylinder Combined functions 75

9 F2H F2H Dimensions (bore size: 8) LCG-8 Stroke length: 0, 20, 30 (The main body fixing holes in this drawing is for 30 mm stroke) RD 2-M5 depth 4 Piping port Main body fixing hole (refer to the A - A' cross section) depth A W M3 depth 4 Common port (Plug) D 7 A L2 L 3 3 D, E oval hole section dimension M3 depth x 2-M3 depth depth 3 2-M2.6 depth M5 depth 4 2-R M4 depth E depth 3 A - A' cross section depth 3 Stroke length L L W 6 26 RD

10 F2H Dimensions Dimensions (bore size: 8) LCG-8 Stroke length: 40, 50, 75 (The main body fixing holes in this drawing is for 50 mm stroke) depth 3 n-main body fixing hole (refer to the A - A' cross section) W D 30 P = 20 4 x 2-M3 depth 3 P x (n - ) L2 L M3 depth 3 2-M5 depth P x (n - ) P = 20 E depth 3 6 Y depth 3 Stroke length L L n W Y RD 4 32 Linear slide cylinder Combined functions 77

11 F2H F2H Dimensions (bore size: 2) LCG-2 Stroke length: 0, 20, 30, 40, 50 (The main body fixing holes in this drawing is for 30 mm stroke) RD 2-M5 depth 4 Piping port depth 4 n-main body fixing hole (refer to the A - A' cross section) A W 2-M3 depth 5 Common port (Plug) M4 depth 4 5 D 38.5 A P = 30 P x (n - ) 2 L2 L 3 x 2-M4 depth 4 2-M3 depth M3 depth 5 2-M5 depth 4 D, E oval hole section dimension depth R M5 depth depth 4 P x (n - ) P = 30 E 6 A - A' cross section 8 Y depth 4 Stroke length L 0 L2 7 8 n W Y RD

12 F2H Dimensions (bore size: 2) Dimensions LCG-2 Stroke length: 75,00 (The main body fixing holes in this drawing is for 00 mm stroke) depth 4 4-main body fixing hole (refer to the A - A' cross section) W D L2 L 4 x 2-M4 depth M3 depth 5 2-M5 depth depth E 8 Y depth 4 Stroke length L L W Y RD Linear slide cylinder Combined functions 7

13 Dimensions (bore size: 6) LCG-6 Stroke length: 0, 20, 30, 40, 50 (The main body fixing holes in this drawing is for 30 mm stroke) T0H T0H RD 2-M5 depth 4 Piping port A n-main body fixing hole (refer to the A - A' cross section) W 2-M3 depth 4 Common port (Plug) D P = 30 P x (n - ) L2 L 3 x 2-M5 depth 5 D, E oval hole section dimension M5 depth A' 2-M3 depth M4 depth 6 2-M5 depth 4 2-R M6 depth P x (n - ) P = 30 E 2 A - A' cross section 8 Y Stroke length L L n W Y T0/5* RD T2/3* 36.5 T2/3W* RD

14 Dimensions (bore size: 6) Dimensions LCG-6 Stroke length: 75,00,25 (The main body fixing holes in this drawing is for 75 mm stroke) T0H n-main body fixing hole (refer to the A - A' cross section) W D 43 P = 30 P x (n - ) 2.5 L2 L 4 x 2-M5 depth M4 depth 6 2-M5 depth P x (n - ) P = 30 E 8 Y Stroke length L L n W Y T0/5* RD 7 T2/3* 53.5 T2/3W* RD.5 5 Linear slide cylinder Combined functions 72

15 Dimensions (bore size: 20) LCG-20 Stroke length: 0, 20, 30, 40, 50 (The main body fixing holes in this drawing is for 30 mm stroke) RD T0H 2-Rc/8 Piping port 2-main body fixing hole (refer to the A - A' cross section) W A 2-M5 depth 5 Common port (Plug) D A L2 L 3 x 2-M5 depth 5 2-M5 depth M4 depth 6 2-R3 D, E oval hole section dimension T0H M5 depth Rc/ M6 depth 40 E 27 A - A' cross section 6 Y depth 6 Stroke length L L W Y T0/5* RD T2/3* 4.5 T2/3W* RD

16 Dimensions (bore size: 20) Dimensions LCG-20 Stroke length: 75,00,25,50 (The main body fixing holes in this drawing is for 00 mm stroke) 2-Rc/8 T0H n-main body fixing hole (refer to the A - A' cross section) W D 4 x 2-5 depth P = 40 5 P x (n - ) L2 L M4 depth P x (n - ) P = 40 E 6 Y Stroke length L L n W Y T0/5* RD 6 T2/3* 6 T2/3W* RD Linear slide cylinder Combined functions 723

17 Dimensions (bore size: 25) LCG-25 Stroke length: 0, 20, 30, 40, 50 (The main body fixing holes in this drawing is for 30 mm stroke) 2-Rc/8 Piping port 2-Rc/8 Common port (Plug) 2-Rc/8 T0H T0H RD W A n-main body fixing hole (refer to the A - A' cross section) M6 depth M5 depth 7 D A 4.5 P = 40 P x (n - ) 5 L2 L x 2-M6 depth 6 2-M5 depth 7 2-R3 D, E oval hole section dimension M8 depth P x (n - ) P = E 33 A - A' cross section depth Y Stroke length L L n W Y T0/5* RD T2/3* 5 T2/3W* RD

18 Dimensions (bore size: 25) Dimensions LCG-25 Stroke length: 75,00,25,50 (The main body fixing holes in this drawing is for 00 mm stroke) n-main body fixing hole (refer to the A - A ' cross section) 2-Rc/8 T0H W D 4.5 P = 40 P x (n - ) 5 L2 L 4 x 2-M6 depth M5 depth 7 6 P x (n - ) P = 40 E 8.5 Y Stroke length L L n W Y T0/5* RD 8.5 T2/3* 7.5 T2/3W* RD 2 77 Linear slide cylinder Combined functions 725

19 Internal structure and parts list LCG A B C Section A for 6 Section A for 8 Section B for 6, 8, 2 Section C for Parts list No. Parts name Material Remarks No. Parts name Material Remarks Hexagon socket head cap bolt Alloy steel Zinc chromate 7 Cushion rubber (H) Urethane rubber 2 Floating bush A Alloy steel Zinc chromate 8 Guard gasket Nitrile rubber 3 Floating bush B Stainless steel 8: Steel C type snap ring Only 8 to 25 8:Steel 2 to 25: Stainless steel 4 C type snap ring Only 8 to 25 2 to 25: Stainless steel 20 Guard Aluminum alloy Chromate 5 Rod packing seal Nitrile rubber 2 End plate Aluminum alloy Alumite 6 Metal gasket Nitrile rubber 22 Hexagon socket head cap bolt Alloy steel Zinc chromate 7 Rod bushing Aluminum alloy Alumite 23 Plug Stainless steel 8 Piston rod Stainless steel 6 to 6: Stainless steel 24 Table Cylinder body Aluminum alloy Hard alumite 20, 25: Steel 0 Cushion rubber (R) Urethane rubber 25 Hexagon socket head set screw Stainless steel Only 6: 0, 40, 50st 26 Floating bush A Stainless steel Spacer Aluminum alloy Only 8: 0st 27 Floating bush B Stainless steel Only 2, 6, 20, 25: 0, 20st 28 Hexagon socket head set screw Stainless steel Only 6 2 Magnet spacer Aluminum alloy Chromate 2 Rod bushing A Stainless steel 3 Magnet Plastic 30 Cap Aluminum alloy Chromate 4 Piston Aluminum alloy Chromate 3 Piston A Aluminum alloy Chromate 5 Plug Stainless steel 32 Piston B Aluminum alloy Chromate 6 Piston packing seal Nitrile rubber Repair parts list Bore size (mm) Kit No. Repair parts number 6 LCG-6K 8 LCG-8K 2 LCG-2K LCG-6K LCG-20K 25 LCG-25K 72

20 Internal structure and parts list Configuration with stopper Type of stopper part with side and bottom parts (symbol D) Internal structure and parts list Without port at stopper section Parts list No. Parts name Material Remarks No. Parts name Material Remarks Stopper bolt Alloy steel Nickeling Stopper block Steel Nickeling 2 Hexagon nut Alloy steel Nickeling (Stopper block symbol: Blank) 7 3 Stopper A Aluminum alloy Alumite Stopper block Alloy steel 4 Gasket Urethane rubber (Stopper block symbol: T) Nitriding 5 Hexagon socket head cap bolt Alloy steel Zinc chromate 8 Stopper B Aluminum alloy Alumite 6 Hexagon socket head cap bolt Alloy steel Zinc chromate Stopper bolt Alloy steel Nickeling 0 Cushion rubber Urethane rubber Linear slide cylinder Combined functions 73