Yamaha TT-R125x Visual Jetting and Airbox Modifications Guide
|
|
- May Watkins
- 7 years ago
- Views:
Transcription
1 Yamaha TT-R125x Visual Jetting and Airbox Modifications Guide WARNING! All of the information contained in this document is intended for private, non-commercial use only and is to be used at your own risk. If you are not mechanically proficient, or proficient in the use of any of the required tools, equipment or supplies, seek qualified help before proceeding. The reader is responsible for any and all damages, injuries, charges, fees, fines, or other liabilities incurred from any use of this information. This document was created from the excellent tutorial by ovrrdrive in the following thread: [Side note: You could probably do this without removing the carb from the bike. However, I wanted the experience of doing it and thought the pictures would come out better, too, so I did.] 1. First, go to the left side of the bike and turn the fuel petcock to the Off (horizontal) position. Remove the fuel line, vent line and overflow line from the carburetor. You may need to gently pry them with a screwdriver to break them loose.
2 2. Next, remove the carburetor from the bike; this is easy to do. Go to the right side of the bike and loosen the screws in the clamps holding the intake boot and manifold to the carburetor. Just loosen them a good bit and the boots will pop right off. Remove the carburetor from the boot leading to the air box, first, and then just pop the carburetor out of the manifold boot. The red arrows indicate the two screws for the boot clamps. 3. The choke cable is the shiny, brass one on the top of the carburetor; it loosens with a 14mm open-end wrench. Loosen it up until it pops up, then gently pull it out of the carburetor. Now, loosen the throttle cable / slide valve / jet needle assembly. I loosened mine with a pair of pliers, then spun it off by hand. After it s loose, just carefully work it out of the carburetor; it should slide out easily. Be very careful not to nick, scratch or bend the jet needle.
3 4. After you have the cables removed from the carburetor, it comes right off the bike. Here s a picture of the throttle cable assembly and the choke cable hanging loose after I took the carburetor out.
4 5. Now, it s time for a few gratuitous pictures of the carburetor detailing some of its features 6. Now, to remove the float bowl from the carburetor Before you try to loosen the four retaining screws on the bowl, hold a well-fitting screwdriver in the screw head and tap the end of the screwdriver a few times with a hammer to break them loose and make them easier to remove without stripping the heads. I forgot to do that to the drain screw and almost rounded it off. After you remove the four screws, the float bowl may still be held in place by the gasket (at least mine was). The last thing you want to do is pull on it really hard on the bowl to break it loose. If you do, you ll probably rip the floats out or bend them when the bowl does break loose. I took a small, regular screwdriver and gently pried the bowl in three or four places until it started to come off. You can also tap on the side of the bowl with the handle of the screwdriver to pop it loose. When it does start coming off, be careful not to rip the bowl gasket so that you can reuse it.
5 Here s a picture of the internals of the carburetor after the bowl was removed: and another showing the float needle and seat below the float assembly:
6 7. The jets come right out pretty easily. When I started to loosen the main jet, the piece underneath it started to turn, too, so I held it with an 8mm open-end wrench while I backed the main jet out. If there is any dirt, sediment, varnish, scale, or oxidation in the carburetor, clean it out thoroughly. This is one part of your bike that should always be spotless. If you use Sta-bil or Seafoam in every tank of gas (and in every gas can you fill), you probably won t have to ever do this again. Here s a picture of the stock #105 main jet on the left and the new #107.5 main jet on the right: 8. Be sure to use a small, well-fitting screwdriver when you remove the Pilot Jet. Here is the stock #15 pilot jet on the bottom and the new #17.5 pilot jet on the top:
7 9. Screw both the main jet and the pilot jet in snuggly, but do not over-tighten them. I then reset the pilot (fuel) screw at 1.5 turns out (CCW) from the fully closed (CW) position as a starting point. Reinstall the float needle, floats and the float bowl. This would also be a good time to replace the four float bowl screws with stainless steel allen-head screws from Home Depot, Lowes, Fastenal, your local motorcycle shop, or your local hardware store so you never have to worry about stripping them in the future.
8 10. Screw the float bowl back on and you re ready for reassembly. The throttle slide has two different slots in it, so you need to pay special attention when you place it back into the carburetor. The wide slot with an angled bottom should line up with the idle screw on the left side of the carburetor. The angled portion rests on the idle screw. It s easier to reassemble if you hold the carburetor perfectly level so that the jet needle will hang straight down and line up with the hole in the needle jet in the bottom of the carburetor s throat. You may need to pull the slide back out a few times before the jet needle drops in correctly. DO NOT FORCE IT!
9 11. After you have finished reinstalling the throttle cable, insert the front of the carburetor into the rubber manifold on the cylinder. Be sure the clamp is loose enough to allow the manifold to expand slightly and be sure to line up the protrusion on the top of the carburetor with the notch in the manifold. It takes a firm push to seat the carburetor into the manifold. Then, install the rear air boot onto the carburetor. Next, reinstall the choke cable. It takes a fair amount of downward pressure on the nut to get engaged onto the threads. Snug it up with a 14mm open-end wrench, then reinstall the overflow line, the vent line and the fuel line and tighten both of the carburetor boot clamps. That s it! Make sure everything is reconnected correctly and everything is tight, then turn the fuel valve back on and give it a go! It really isn t too bad of a job if you just take your time and do it right. Now, while I had everything else apart, I pulled the spark plug out to see the color of the insulator. It looked like the jetting was dead-on before. I figured if I wanted any improvement, at all, I d better do some air box modifications to compliment my new jetting. Otherwise, I would be adding a lot more fuel but no additional air which would make it run too rich. I wanted to do the air box modifications, anyway, so here it goes Here s a picture of a good-looking spark plug from a properly-jetted engine. Note that the small, round, ceramic insulator surrounding the small, metal tip has a sort of cardboard color to it. If it s white or pitted, then the engine is running too lean (not enough fuel), if it s very dark brown or black, then the engine is running too rich (too much fuel).
10 Here is a picture of the top of the stock air box with the seat removed: 12. Wiggle the rubber air snorkel while pulling up to remove it from the top of the air box. Here s a top view of the air box with the snorkel removed:
11 13. On the left side of the bike, remove the three screws holding the triangle-shaped cover on the front of the air box, remove the cover, then pull the screen out. Reinstall the cover and the three screws. Here s a picture of the air box from the right side with the screen removed:
12 After all was said and done, the only parts I had left over were the ones that I was supposed to! And that, as they say, is that. After I cranked it up, I ended up going out about a ½ turn more (CCW) on the pilot (fuel) screw as it was popping a bit and the change improved things. I ll need a good riding day to be sure, but I think the #107.5 main jet may not be big enough. I ll probably change it to the #110 main jet I picked up. Ride reports initially are that it has more bottom-end grunt and smoother acceleration through the power band. It just feels more like it should; not like it s being held back. Overall, these were very easy modifications and worthwhile, I think. Well, how d I do? Suggestions, comments?
13 TT-R125 Jets Large round type Mikuni main jets (N ) &webCatId=16&prodFamilyId=25091&allVehParts=true CatId=&mmyId= VM28/486 Pilot Jets &webCatId=16&prodFamilyId=24380&allVehParts=true tid=&mmyid= =2&whichPage=home&vehicleId=&headerVehicleTypeId=2&headerMake=8&headerModel=4383&headerYear= Also, a RotoZip or Dremel with a similar rotary cutting bit work well to cut the top out of the air box for additional air flow. Just be sure to vacuum or blow out all of the plastic.
RULE # 1 is DON T mess with things that you don t know anything about! (Take them to a pro & pay them to fix it)
OK there seems to be a LOT of problems noted on KatRiders having to do with CARBS, so I thought I d write out sort of a checklist of things to help folks. RULE # 1 is DON T mess with things that you don
More informationhttp://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html
http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -
More informationTABLE OF CONTENTS. Section 1 - Assembling your new pit bike.
Orion Pit Bike Sales Owners Manual (All information and content is the property of Orion Pit Bike Sales. Any attempt to copy or resell is a direct violation of our copyright. All violators will be prosecuted)
More informationHonda CX500 & GL500 Forum
Welcome to Honda CX500 & GL500 Forum Sign in Join Faq Honda CX500 & GL500 Forum Discussion about the CX500, CX650, GL500, GL650, and Turbo variants Links Events Photos Forums CX500 Chopper Project Home
More informationHarley Davidson CV Carburetor Upgrade
Harley Davidson CV Carburetor Upgrade Harley Davidson started equipping models with the CV carburetor in 1989 and has utilized the same carb ever since. A CV carburetor (Constant Velocity) incorporates
More informationFigure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top.
Here are some pictures to show what s required when replacing the A/C compressor, expansion valve and receiver/drier on a 2001 Volvo V70. Even if you don t replace these A/C parts these pictures can help
More informationM-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationINSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
More informationBuilding A Computer: A Beginners Guide
Building A Computer: A Beginners Guide Mr. Marty Brandl The following was written to help an individual setup a Pentium 133 system using an ASUS P/I- P55T2P4 motherboard. The tutorial includes the installation
More informationInstallation Instructions 4508 4508S
SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect
More information1998-2002 Suzuki Katana Fender Eliminator
1998-2002 Suzuki Katana Fender Eliminator The following are instructions and illustrations on the installation of the custom fender elimination. 1 Begin by removing seat, both rear fairings, and tail light
More informationCOOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011
COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 Below are instructions for the Mini Mania Pulley Upgrade Kit, Part Number NME5011. Please take all necessary precautions for working
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationTechnical Specifications
Mfg: Honda Make: XR50R Year: All Product: 81.2cc E-Stage Bore Up Kit (part # 010-1-05-522) 88cc S-Stage Bore Up Kit (part # 010-1-05-502) IMPORTANT - PLEASE READ CAREFULLY We recommend that this performance
More informationDive Rite 200 & 300 Bar Isolator Manifold Service Manual
Dive Rite 200 & 300 Bar Isolator Manifold Service Manual Principal Photography and Text by Pete Nawrocky Copyright 2003 Lamartek Inc. D/B/A Dive Rite 0 Warning This manual is only to be used as a guide
More informationMGA Alternator Conversion
MGA Alternator Conversion Installation Instructions For 1955 to 1962 MGA PART # 130-078 and #130-088 440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationFord F-Series Column Shift Repairs
Ford F-Series Column Shift Repairs I ve had it on my list to tighten up the linkage on my 52 s column shift setup for a long time. I tried to get it apart when I had all the front end sheet metal off,
More informationFord 8N Tractor Overhauls - Carburetor
Ford 8N Tractor Overhauls - Carburetor By Don Steward (Don8NAZ) The carburetor kit for the TSX-241A/B/C carburetor is being supplied in only one flavor nowadays. It includes a replacement throttle shaft,
More informationREPAIR AND MAINTENANCE MANUAL
REPAIR AND MAINTENANCE MANUAL Professional Pest Control Application Equipment Prime Line Sprayers B&G Equipment Company 135 Region South Drive, Jackson, GA 30233 800.544.8811 Phone 678.688.5601 Fax 678.688.5633
More informationCorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6
CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize
More information5800 Temperature Sensor Cable Assembly
5800 Temperature Sensor Cable Assembly Removal and Replacement Instruction Sheet #60-4702-070 Revision D, January 14, 2013 Overview The 5800 has two refrigeration temperature sensors, one attached to the
More informationInstalling a new 928 Motorsports All-Aluminum Radiator
928 Motorsports Supercharger Installation Copyright 2008, 928 Motorsports, LLC All Rights Reserved Installing a new 928 Motorsports All-Aluminum Radiator Copyright 2008 928 Motorsports, LLC. Toll-Free
More informationWritten By: Sam Lionheart
iphone 5s Battery Replacement Replace the battery in your iphone 5s. Written By: Sam Lionheart INTRODUCTION Use this guide to bring life back to your iphone 5s with a new battery. Removing the battery
More informationAssembly and Usage Instructions
Assembly and Usage Instructions A Product 5885 West Van Horn Tavern Road Columbia, MO 65203 www.caldwellshooting.com Instruction #1001667 Limited Warranty Every Caldwell product is warrantied to be free
More informationOverview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer
Overview READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION PARTS LIST A. Flush valve B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve
More informationENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER...
FUEL FILTER............................ FUEL HEATER.......................... INJECTOR.............................. SUPPLY PUMP.......................... COMMON RAIL.......................... FUEL PRESSURE
More informationInstallation Guide 2010 BMW S1000RR Full Exhaust System
Installation Guide 2010 BMW S1000RR Full Exhaust System!! THIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE!! Congratulations on the purchase of your new TaylorMade
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks
TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationCorkSport Mazda 3 LED Light Kit 2014+ Mazda 3
CorkSport Mazda 3 LED Light Kit 2014+ Mazda 3 Thank you for purchasing the CorkSport 2014 Mazda 3 LED Light Kit. CorkSport's LED light kit replaces bulbs for the rear dome light, vanity visor lights, front
More informationCooling system components, removing and installing
Engine BHW Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! When doing any repair work, especially in the engine compartment,
More informationSALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT
SALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT INSTALLATION MANUAL: 2005 MUSTANG 4.6 3V MANUAL P/N: 10-8002-C14338C SUPERCHARGER KIT P/N: 10-1607-B14083* Saleen Performance, Inc. 1225 East Maple Rd.,
More informationSoftail Oil Change. Tools
From time to time I see question on the forum regarding doing an oil change on a Harley and more specifically about doing a scavenging oil change on a Softail. Since there didn't seem to be a good thread
More informationJake's Big Airbox Modification
1 sur 12 29/11/2012 16:32 Jake's Big Airbox Modification Captain Jake, the Mel Bay of Motorcycle Modification presents: FREE YOUR AIRBOX! What follows is documentation and photographs of the airbox modification
More informationPARTS NEEDED FOR CONVERTING FROM LP TO NG
1 6 7 8 3 5 4 10 9 2 PARTS NEEDED FOR CONVERTING FROM LP TO NG Number Description 1 30" NG Manifold 2 NG side burner valve 3 NG Regulator 4 Rear I/R NG orifice 4 Rear I/R NG orifice 5 Side burner NG orifice
More informationINGROUND, ROPED, AND HOLELESS JACK SEAL REPLACEMENT
D. L. Martin Company INGROUND, ROPED, AND HOLELESS JACK SEAL REPLACEMENT TYPICAL HYDRAULIC JACK HEAD ASSEMBLY 1 TOOLS REQUIRED: 1) Container to hold hydraulic fluid. 2) Clean rags and protective covers
More informationPOLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS
POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS Polemount Field Fix Support If you have any questions or incur any problems installing or using the new Polemount, please use Miovision s Support System by emailing
More informationBUGGY SETUP GUIDE. Volume GOKARTSUSA GY6 150, CN250. Buggy Setup Guide
BUGGY SETUP GUIDE Volume 1 GOKARTSUSA GY6 150, CN250 Buggy Setup Guide GY6 150, CN250 DUNE BUGGY Buggy Setup Guide GOKARTSUSA.COM 2000 Highway 50 S. Lake Tahoe, CA 96150 Phone 800.603.1437 2 Table of Contents
More informationFitting Instruction: Daytona 675 Street Triple from VIN 411984, Street Triple R from VIN 411984 A9930222
English Fitting Instruction: Daytona 675 Street Triple from VIN 98, Street Triple R from VIN 98 A990 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's
More informationBODY-12, Door Handle - Removal, Installation, and Adjustment
Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationAstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech Components 1 Sky Commander Digital Setting Circle Computer 2 Encoders 10,000 step 1 Sky Commander Digital Setting Circle Manual
More informationInstallation Instructions
Instructions Created by an: Suzuki Samurai Sidewinder CV Carburetor Adapter Kit (SKU# SEU-CVCK-40 ) Instructions also apply to: SEU-CVCK-44 Installation Instructions Revised 09-22-15 CAUTION: Safety glasses
More informationSplitting the feed screw nuts and adjusting backlash on a Bridgeport Milling Machine.
Splitting the feed screw nuts and adjusting backlash on a Bridgeport Milling Machine. Bridgeport manufactures their milling machines with 0.005 backlash in the feedscrews, which increases over time due
More informationFront brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
More informationEASY START SYSTEM. Toni Clark practical scale GmbH EASY START SYSTEM 1
1 GB Toni Clark practical scale GmbH 2 2 INSTALLATION: Unplug the connector in the red lead from power coil to spark coil. Push the round plug of the Easy Start into the power coil s red lead connector.
More information2005-2007 Ford Focus Front Brake Rotors
2005-2007 Ford Focus Front Brake Rotors Replacement Replacing the rotors in 2005-2007 Ford Focus models with rear drum brakes. Written By: David Hodson INTRODUCTION The steps in this guide are used to
More information430 Power/Electronics Replacement
Replacing the main board WARNING Before proceeding, turn off the main power switch and unplug the power cord. Caution Make sure you are properly grounded with an ESD strap before continuing. The main printed
More informationThe M14 Conversion to The M1 Garand Version One
The M14 Conversion to The M1 Garand Version One Project Completed and Written By Lee Cassar Feb. 19, 2007 Table of Contents Introduction:... 3 Tools needed for the Conversion:... 4 Disassembly:... 5 Modifications:...
More informationNavico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement
Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations
More informationCleaning Instructions, Pilot Replacement and Valve Change. Model No.: 233010 Natural Gas
Cleaning Instructions, Pilot Replacement and Valve Change Model No.: 233010 Natural Gas 8mm open-end wrench 9mm open-end wrench 10mm open-end wrench 12mm open-end wrench 13mm open-end wrench Phillips screw
More informationInstructions for: TTW 1 Universal Service Replacement Blower Kit P/N 265-47200-00
Instructions for: TTW 1 Universal Service Kit P/N 265-47200-00 (To be performed ONLY by qualified service providers) The Blowers on the Following Water Heaters are Serviced by This Kit: MITW -10 Series
More informationInstallation instruction do88 Intercooler for Volvo S40 / V50 / C30
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At
More informationTool And Material Checklist
HOW - TO CV JOINTS CV JOINTS Tool And Material Checklist Screwdriver Metal Shears Breaker Bar or Torque Wrench Assorted Wrenches Wire Evaporating Spray Solvent Pusher Tool Vise Snap Ring or Duckbill Pliers
More informationSTEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13
STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT
More informationFRONT TURN SIGNAL RELOCATION KIT
-J0 REV. 00-0-0 FRONT TURN SIGNAL RELOCATION KIT GENERAL Kit Number -0 Models This kit fits 00 and later Dyna model motorcycles (except FXDSE), relocating the front turn signal from the handlebars to the
More informationSCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT
REV. 2015-04-23 SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 29299-08, 29098-09 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories
More informationDrive shaft, servicing
Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,
More information3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE
4 3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE A. Changing the Control Board B. Replacing a Heating Element C. Thermistor Replacement D. High Limit Switch Replacement E. Level Detector Replacement
More informationOwner s Manual Read and keep this manual. Patents World Wide
Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2008 All Rights Reserved The following manual is provided to assist
More informationHow To: Retrofit the Morimoto Mini D2S bi-xenon Projectors
How To: Retrofit the Morimoto Mini D2S bi-xenon Projectors Warning: By reading this document I agree that it is only intended to be used as an educational guide. The Retrofit Source Inc. makes no guarantee
More informationPISTON AND CYLINDER WALLS SCORING
PISTON AND CYLINDER WALLS SCORING Most instances of piston & cylinder scoring can be traced to lack of oil, use of improper oil fuel mixture, foreign particles in cylinder, heating caused by plugged cooling
More informationBILLET HEADLAMP SHELL
-J008 REV. 007-07- BILLET HEADLAMP SHELL GENERAL Kit Number 770-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com
More informationFRONT WINDSHIELD SEAL INSTALLATION
FRONT WINDSHIELD SEAL INSTALLATION Tech Article From Newsletter 16.1-1st Quarter of 2010 Replacing your Front Windshield Seal ISN T AS HARD AS YOU MAY THINK! Recently, we retooled our front window seal
More informationBOBBIN WINDER - TYPES & FUNCTION
BOBBIN WINDER - TYPES & FUNCTION 13.1.006 The bobbin winder is a separate unit screwed on to the machine, adjacent to the balance wheel. Its function is to wind a reserve of cotton evenly onto an empty
More informationAuto-belay Cable Replacement Process
Auto-belay Cable Replacement Process Version 2.00 WARNING: The air pressure in the auto-belay system is what causes the cable to be retracted when releasing the cable or climbing the wall with the cable
More informationCarburetion Troubleshooting Quick Reference Guide
Carburetion Troubleshooting Quick Reference Guide SERVICE DIAGNOSTIC OVERVIEW A logical, planned approach can move service work through a repair center in a smooth and efficient manner. Fueled by information
More informationSCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT
REV. 05-04- SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 95-08B, 9006-09B, 876-0A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories
More informationModular Locomotive System Instruction Manual for HBK5 Billy Body Kit
Modular Locomotive System Instruction Manual for HBK5 Billy Body Kit Roundhouse Engineering Co. Ltd. Units 6-10 Churchill Business Park. Churchill Road, Wheatley. Doncaster. DN1 2TF. England. Tel. 01302
More informationCompliments of SwatchBattery.com
Compliments of SwatchBattery.com Tools Y O U W I L L N E E D Case Holding Vise Case Knife Fine-point Tweezers Plastic Tweezers Small Screwdriver EWB-1 Battery Tester Case Wrench Watch Closing Hand Press
More informationDTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual
DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR Installation and Operation Manual 1 ENGLISH Safety Instructions 2 Features 2-3 Specifications 3 Installation 4-5 Wiring Diagrams 6-7 Warranty 8
More informationDeskCycleTM USER S MANUAL QUESTIONS / PROBLEMS. Order# Support for US Customers TOLL-FREE SUPPORT 877-426-3292 EMAIL SUPPORT support@3dinnovations.
TM DeskCycleTM USER S MANUAL Visit us at www.deskcycle.com for, Usage Tips Calorie Calculator Accessories And More QUESTIONS / PROBLEMS Support for US Customers TOLL-FREE SUPPORT 877-426-3292 EMAIL SUPPORT
More information1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS
By Denny Williams Photos by Denny Williams 1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS Denny Williams - Technical Writer Denny is first and foremost a dyed-in-thewool
More informationVW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS
VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS Tools required: 10mm/13mm socket and 3/8 drive ratchet with extension Torx T20/25/30 screwdrivers or bits Phillips head screwdriver,
More informationCHROME FRONT BRAKE MASTER CYLINDER KIT
-J075 REV. 009-0-0 CHROME FRONT BRAKE MASTER CYLINDER KIT GENERAL Kit Number 5-99D, 5-99D Models These Chrome Master Cylinder Kits are designed to replace the original equipment front brake master cylinder
More informationA&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
More informationSpreader Light Bulb Replacement Instructions
Spreader Light Bulb Replacement Instructions IMPORTANT: DISCONNECT LIGHT FROM BATTERY BEFORE PROCEEDING. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR OTHER DAMAGE. Tools Needed You will need the following
More informationFUEL SYSTEM 2-1. Table of Contents. Fuel Removal Installation
Specifications Special Exploded Tools View, Throttle Surge Choke Throttle Choke Tank Cable Grip Cable Cable and Adjustment Adjustment Cables, Air Carburetors Surge Air Oil Service Element Carburetor Idle
More informationManual for GlobePharma Mini-Press II Rotary Tablet Press
1 of 13 Preparing the Rotary Press 1. Make sure the rotary press is unplugged. 2. Open the bottom cabinet of the rotary press and take out the grey tool kit, and the beige box of punches and dies. 3. Take
More informationArctic Leash Instruction Manual Alaskan Products Company LLC.
Retractable Cord Reel for Engine Block Heaters Arctic Leash Instruction Manual Alaskan Products Company LLC. INSTALLATION INSTRUCTIONS This instruction manual is a reference guide for installing and operating
More informationM-9000-ZX3 JRSC Focus Big Boost Upgrade Kit INSTALLATION INSTRUCTIONS
Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: These instructions
More informationHigh Flow Air Cleaner Assembly
34-0112 High Flow Air Cleaner Assembly 34-0114 34-1128 34-0113 34-0105 34-0178 Big Sucker Air Filter Kits for Carbureted or Fuel Injected Twin Cam and EV2 Big Twin Models. The all-in-one backing plate
More informationH EAD TUBE BASICS. Figure 1 - Head tube, front fork and hardware
H EAD TUBE BASICS Figure 1 - Head tube, front fork and hardware This tutorial will cover some of the basics you need to know when pulling apart the steering system of a bicycle for repair or use on one
More informationContents. Front Derailleurs... 2. Part One - Planning... 2 I. Objectives... 2 II. Materials Needed... 2 III. Setting...2 IV. Evaluation...
Contents... 2 Part One - Planning... 2 I. Objectives... 2 II. Materials Needed... 2 III. Setting...2 IV. Evaluation... 2 Part Two - Activity Instructions... 3 Steps to Adjusting and Replacing... 3 Disassemble...
More informationBuild Your Own Solar Car Teach build learn renewable Energy! Page 1 of 1
Solar Car Teach build learn renewable Energy! Page 1 of 1 Background Not only is the sun a source of heat and light, it s a source of electricity too! Solar cells, also called photovoltaic cells, are used
More informationREPLACE A TOILET FILL VALVE
PROJECT 15 REPLACE A TOILET FILL VALVE 110 PLUMBING OKAY, SO YOU ARE AT PLAN B. Honestly, replacing a fill valve is no biggie. Of course, you can make a big deal and brag to your friends how you saved
More informationINSTALLATION GUIDE. Your guide to Stromberg 97 carburetor installation and adjustment
INSTALLATION GUIDE If you need further information or assistance, please contact your Genuine Stromberg dealer, or email us direct at tech@stromberg-97.com or log on to our Tech Center at www.stromberg-97.com
More informationInstallation Instructions 6028.801
DAZZLE Installation Instructions 08.80 Spread Lavatory Faucet with Speed Connect Drain* Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationMercedes W208 (CLK 99 03) Case Cover Lock/Rear Bow Lock Replacement and Hydraulic Fluid Flush
Mercedes W208 (CLK 99 03) Case Cover Lock/Rear Bow Lock Replacement and Hydraulic Fluid Flush Because a convertible is only cool if the top goes down. Version 1.0 August 9, 2012 by joetwa Table of Contents
More informationStep by step guide to installing your own Ku Band satellite dish
Step by step guide to installing your own Ku Band satellite dish If you don't feel comfortable installing your own system, your local TV Aerial or Handyman can easily follow these helpful guidelines for
More informationTUTORIAL. REbUILdING. REAR CALIpER O-RING CONVERSION CORVETTE 1965-82. Part #: HT-2
Part #: HT-2 1965-82 CORVETTE O-RING CONVERSION REAR CALIpER REbUILdING TUTORIAL Choosing a Brake Caliper Rebuild Kit Standard Lip Seals vs. O-Ring Seals Lip seal design seals are used on 1965-1982 Corvette
More informationOriginal Assembly Guide
TCT Multipurpose Single Bevel Sliding Compound Mitre Saw Original Assembly Guide Read instructions before assembling this tool. Table of Contents GB Assembly Guide Read instructions before assembling this
More informationCable Drum Installation
20 Cable Drum Installation COUNTERBALANCE None Shake the TorqueMaster spring tube gently to extend the winding shafts out about 5" on each side. For single spring applications, there will be no left hand
More information2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13)
2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13) Exploded View Special Tools Required Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool 07GAF-SD40100 Bearing driver attachment,
More informationTUTORIAL. REbUILdING. front CALIpER O-RING CONVERSION CORVETTE 1965-82. Part #: HT-1
Part #: HT-1 1965-82 CORVETTE O-RING CONVERSION front CALIpER REbUILdING TUTORIAL Choosing a Brake Caliper Rebuild Kit Standard Lip Seals vs. O-Ring Seals Lip seal design seals are used on 1965-1982 Corvette
More information