baby in-sight Magical Firefly Auto Mirror

Transcription

1 63013 baby in-sight Magical Firefly Auto Mirror Keep these instructions for future reference as they contain important information. Adult installation required. Accessories not included. birth+ User Manual

2 Mirror Features Front View Remote Features B Top View C Bottom View G D E F H A Power button B Power indicator light A C Remote Transmitter D Entertaining Mode E Soothing Mode F Volume G Visor Clip H Battery Compartment Important: For optimum performance, ensure the remote has an unobstructed visual path to the mirror. 1 2

3 Operating Mirror Remove Demo Tab The mirror is equipped with a demo mode feature. Before using the mirror, pull out the plastic demo tab located on the back of the battery box and discard it for normal operation. Important: The mirror includes 3 AA batteries for in-store demonstration only. Battery life may be impaired. Replace mirror batteries with 3 new AA alkaline batteries (not included ) for normal use. Remote requires 1 CR2032 coin cell battery (not included). 1. Press button on front of mirror. Power indicator light will appear. The button on the front of the mirror must be pressed in order to operate remote control and mirror features. 2. Press desired mode on remote control: Soothing Mode a. Press button on remote once to activate soothing mode. Press again to stop. NOTE: Soothing mode stops automatically after approximately 12 minutes. Press button again to restart. Entertainment Mode b. Press button on remote once to activate entertainment mode. Press again to stop. NOTE: Entertainment mode stops automatically after approximately 12 minutes. Press button again to restart. Important: For optimum performance, ensure the remote has an unobstructed visual path to the mirror. 3 Operating Mirror, continued Auto Shut-Off Battery Conservation To help conserve battery life, the mirror automatically shuts off after 1 hour of inactivity. The power indicator light will turn off and mirror cannot be activated by the remote during this time. To reactivate, press button on mirror. Power indicator light will appear. Manual Shut-Off Press and hold button for 3 seconds. Power indicator light will turn off. 4

4 Battery Installation Battery Installation, continued Remote Battery Door Remote: Loosen the screw in the battery compartment door with a Phillips head screwdriver. Remove the battery compartment door. Correctly insert 1 CR2032 coin cell battery with the polarity shown in battery compartment. Replace the battery compartment door and tighten the screw with a Phillips head screwdriver. Do not overtighten. PULL Mirror Battery Door Mirror: Remove Demo Tab: The mirror is equipped with a demo mode feature. Before using the mirror, pull out the plastic demo tab and discard it for normal operation. Important: The mirror includes 3 AA alkaline batteries for in-store demonstration only. Battery life may be impaired. Replace mirror batteries with 3 new AA alkaline batteries (not included) for normal use. Important: If the mirror does not respond to the remote, it does not necessarily mean that the battery power in the remote is low. Check the orientation of the batteries in the battery compartments to make sure they are properly installed. Hint: Remove the mirror from the seat back prior to replacing the batteries. Loosen the screw in the battery compartment door with a Phillips head screwdriver. Remove the battery compartment door. Correctly insert 3 AA batteries with polarity shown in battery compartment. Hint: We recommend using alkaline batteries for longer battery life. Replace the battery compartment door and tighten the screw with a Phillips head screwdriver. Do not overtighten. Important: Under normal use conditions, the batteries in the mirror will require replacement more often than the battery in the remote. When the mirror s music becomes faint, it s time to replace the batteries in the mirror. 5 6

5 Battery Safety Information CR2032 Lithium Battery 3V Shown Actual Size 1.5V x 3 AA (LR06) Shown Actual Size In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin the remote or the mirror. To avoid battery leakage: Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). Insert batteries as indicated in battery compartments. Remove batteries during long periods of non-use. Always remove exhausted batteries from the remote and mirror. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak. Never short-circuit the battery terminals. Use only batteries of the same or equivalent type, as recommended. Do not charge non-rechargeable batteries. Remove rechargeable batteries from the remote and mirror before charging. If rechargeable batteries are used, they are only to be charged under adult supervision. 7! CAUTION Always verify that the mirror is properly secured on the seat back, head restraint or tether anchor. Check frequently.! WARNING Prevent strangulation or entanglement. Never place or attach to a crib. Never add strings or ties to the product. Never leave child unattended. Important Safety Precautions: Keep mirror out of baby s reach and direct sunlight. Always carefully follow car seat manufacturer s directions for correct installation and position of a child safety seat. To Clean: Wipe the mirror with a soft, damp cloth. Fabric is surface washable with a damp cloth and mild soapy water. Do not submerse mirror in water. 8

6 Mirror Features Rear View I Attaching Mirror D-Ring Clip J 3 Strap K Adjustable Stand L M Clamp I D-Ring J Adjustable Stand K Battery Compartment L Fastener M Clamp N O Back Seat Head Restraint Raise head restraint. Insert clamp underneath head restraint. Wrap adjustable stand over top of head restraint. Bend clamp upward to conform to head restraint. Attach strap s clip to D-Ring. Lower head restraint down to secure in place. Tighten strap and rotate mirror to desired angle so your child is visible to driver in vehicle s rear-view mirror. N Strap O Clip 9 10

7 Attaching Mirror Attaching Mirror Adjustable Stand Fastener Clip Adjustable Stand Clamp Tether Anchor Fastener Clamp Tether Anchor IMPORTANT: DO NOT ATTACH THIS PRODUCT TO YOUR VEHICLE S TETHER ANCHOR IF YOUR CHILD SAFETY SEAT IS INSTALLED IN YOUR VEHICLE USING THIS ANCHOR. Position mirror on seat back in front of tether anchor. Insert clamp between seat back and rear deck of your vehicle. Bend clamp to conform to seat back shape. Attach clip to tether anchor and tighten strap. Unfasten adjustable stand s fastener and tilt mirror to desired angle so your child is visible to driver in vehicle s rear-view mirror. NOTE: The tether anchor attachment method is designed for sedan vehicles. If you own a minivan, station wagon or sport utility vehicle (SUV) and would like to use the tether anchor attachment method, you may need a tether extender. Please visit BRICA at brica.com or call Center Back Seat on Bench Seat Position mirror on center of back seat. Bend clamp to conform to top of seat back. Squeeze clamp firmly to secure mirror in place. Unfasten adjustable stand s fastener, and tilt mirror to desired angle so your child is visible to driver in vehicle s rear-view mirror. NOTE: If a tether anchor is accessible and not in use by your child safety seat, attach clip to tether anchor and tighten strap. This will help increase the stability of mirror. If you own a minivan, station wagon or sport utility vehicle (SUV), you may need a tether extender. Please visit BRICA at brica.com or call

8 Attaching Mirror FCC Note (United States Only) Clip D-Ring Strap Clamp Adjustable Stand Front Head Restraint (for forward-facing children) Raise head restraint up. Insert clamp underneath head restraint. Wrap adjustable stand over top of head restraint. Bend clamp upward to conform to the head restraint. Attach strap s clip to D-Ring. Lower head restraint down to secure in place. Tighten strap and adjust the mirror so child can see themselves. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the legal limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio /TV technician for help. NOTE: Changes or modifications not expressively approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment. NOTE: This method is used for mounting mirror to back side of driver or front passenger seat for entertaining forward-facing children

9 making together better Questions? Retain this address for future reference. USA 2013 BRICA, Inc., 500 West 5th Street, Suite 220, Charlotte, NC brica.com Australia CNP Brands, PO Box 8 Deer Park VIC cnpbrands.com.au Printed in China