TMS 152 / 152T / 152XT TECHNICAL MANUAL
|
|
- Darcy Chambers
- 7 years ago
- Views:
Transcription
1 TMS 152 / 152T / 152XT TECHNICAL MANUAL
2 BLANK PAGE
3 FEATURES FEATURES TMS 152 (non-thermal), 152T (single thermal barrier), and 152XT (double thermal barrier) are front set flush glazed systems that are 6" deep with a 2" wide sightline Glaze from the outside or inside Screw spline or shear block fabrication Glazing options 1/4" to 1-1/4" thick Available in anodized and standard or custom painted finishes Readily available from stock APPLICATIONS Storefront, Punched Openings, or Ribbon Windows Single span Integrated entrance framing to allow Pittco standard entrances or other speciality entrances to be incorporated SYSTEM PERFORMANCE (TMS 152T Single Thermal) Description Test Method Allowed Achieved Test Report Structural ASTM E 0 N/A 0 psf 24-01B Air ASTM E psf psf 24-01B Water (Static) Water (Dynamic) ASTM E 1 AAMA psf 5 psf 10 psf 10 psf 24-01B 24-01B CRF AAMA 150 N/A U Value U Value AAMA 150 NFRC 100 N/A N/A SHGC NFRC 200 N/A CR NFRC 500 N/A SYSTEM PERFORMANCE (TMS 152XT Double Thermal) Description Test Method Allowed Achieved Test Report Structural ASTM E 0 N/A 0 psf 24-01B Air ASTM E psf psf 24-01B Water (Static) Water (Dynamic) ASTM E 1 AAMA psf 5 psf 10 psf 10 psf 24-01B 24-01B CRF AAMA 150 N/A U Value U Value AAMA 150 NFRC 100 N/A N/A SHGC NFRC 200 N/A CR NFRC 500 N/A " IGU (1/4-1/2-1/4) Solarban 70 Low-E, High Performance Spacer, 90% Argon FOR SPECIFIC PRODUCT APPLICATIONS PLEASE CONTACT YOUR PITTCO REPRESENTATIVE 1
4 BLANK PAGE 2
5 INDEX PRODUCT DESCRIPTION - NON THERMAL PAGES 4 TO 8 PRODUCT DESCRIPTION - THERMAL PAGES 9 TO 1 EXPLODED VIEWS PAGE 14 1/4 SIZE DETAILS - TMS 152 NON THERMAL PAGES D1 TO D 1/4 SIZE DETAILS - TMS 152T SINGLE THERMAL PAGES D4 TO D6 1/4 SIZE DETAILS - TMS 152XT DOUBLE THERMAL.... PAGES D7 TO D9 ENTRANCE DETAILS PAGE D10 WINDLOAD CHARTS PAGES S1 TO S10 DEADLOAD CHARTS PAGE S11 TO S1 SECTION PROPERTIES PAGE S14 TO S15 THERMAL CHARTS PAGES T1 TO T2
6 NON-THERMAL PRODUCT DESCRIPTION BASIC USES / RELATED USES Framing is designed for flush, center glazed storefront assembly Vertical mullions are typically open back aluminum members, with solid face and flush closure plates forming tubular members for use on single spans Horizontal mullions are of hollow aluminum with removable glazing stops Corners are configured for 90 and 15 degrees Glazing is insulating glass unit or single pane with adapters Glass may be transparent, opaque, or decorative types Framing is intended for one story applications Framed assembly may be fitted to most rigid and stable framed opening assemblies PRODUCT ATTRIBUTES AND CHARACTERISTICS Framing and glazing stops are designed for glass and panels Wind pressure resistance and pressure equalization are standard within the frame assembly Weep containment and condensate water collection and drainage to the exterior at concealed weeps are standard Integral door frames are available SELECTION CRITERIA Quality, economy, and good performance are provided at a reasonable cost Framing is designed for Interior or exterior environments APPLICABLE STANDARDS, RELATED REFERENCES AA (Aluminum Association) - Designation System for Aluminum Finishes AAMA SFM Aluminum Storefront and Entrance Manual AAMA Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors using Dynamic Pressure AAMA Voluntary Specification for Anodized Architectural Aluminum AAMA Voluntary Test Method for Thermal Transmittance and Condensation Resistance of Windows, Doors, and Glazed Wall Sections AAMA Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels AAMA Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels ASTM A12/A12M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products ASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate ASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric] 4
7 PRODUCT DESCRIPTION NON-THERMAL ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube ASTM B221M - Standard Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube [Metric] ASTM E28 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under Specified Pressure Differences Across the Specimen ASTM E0 - Standard Test Method for Structural Performance of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference ASTM E1 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference QUALITY, TESTS, CERTIFICATIONS, AND APPROVALS Air Infiltration: Maximum leakage of 0.02 cfm/sq ft. when measured in accordance with ASTM E28 at a test pressure of 6.24 psf Static Water Leakage: No uncontrolled leakage, when measured in accordance with ASTM E1 at a test pressure difference of 12.0 psf Dynamic Water Leakage: No uncontrolled leakage, when measured in accordance with AAMA at a test pressure difference of 12.0 psf Structural Performance: Maximum deflection less than 1/175 of the span length and no damage to the assembly, when measured in accordance with ASTM E0 at a test pressure of 25 psf PACKAGING, HANDLING, AND PROTECTION INSTRUCTIONS Packaged in specially designed heavy cartons or shipped pre-fabricated and assembled SPECIAL WARRANTY One (1) year LIMITATIONS Not thermally broken Framing is limited to applications of one story in height Not intended for continuous members for multiple floor applications SAFETY PRECAUTIONS Normal precautions required AVAILABILITY Framing is available in all regions of USA - refer to Internet web site for locations and addresses of distributors COST Varies with elevation, configuration and finish desired 5
8 NON-THERMAL PRODUCT DESCRIPTION PRODUCT PROPERTIES MATERIAL AND DESIGN Aluminum: 606-T6 alloy and temper, to ASTM B221 or ASTM B221M Fasteners: Stainless steel, or zinc plated carbon steel Perimeter Anchors: Aluminum, or steel that will be isolated from aluminum components Glazing Gaskets: Wedge-type, Ethylene Propylene Diene Monomer (EPDM) rubber with non-stretch cord Glass Stops: Snap-in type SHAPE AND DIMENSIONS Frame Size: 2 x 4-1/2 inch Glass Edge Bite: /8 inch Glazing Thickness Accepted: 1/8 inch to 1-1/8 inch in increments of 1/16 inch except 7/16 inch, 9/16 inch, 11/16 inch, and 1/16 inch SHOP FABRICATION AND ASSEMBLY Provide for flush glazing on all sides with no projecting stops Configurations: Two-piece snap together mullions Solid tubular mullions, assembled to specially designed shear block clips Accessories: Expansion Mullions Corner Mullions Open Back Perimeter Members Integral Door Frames Flashing, Subsills Head Receptor Heavy Duty Mullions Standard Steel Reinforcing Available COLORS AND TEXTURES Architectural anodic coating, in accordance with AAMA 611; o Aluminum Association Designation. AA-M10C22A1 - Class II - (Pittco #42 Clear) AA-M10C22A41 - Class I - (Pittco #4 Clear) AA-M10C22A44 - Class I - (Pittco #59 Champagne) AA-M10C22A44 - Class I - (Pittco #60 Light Bronze) AA-M10C22A44 - Class I - (Pittco #61 Medium Bronze) AA-M10C22A44 - Class I - (Pittco #62 Dark Bronze) AA-M10C22A44 - Class I - (Pittco #6 Black) 6
9 PRODUCT DESCRIPTION NON-THERMAL Architectural organic coating, in accordance with AAMA 2604 (50% Kynar 500 ); o Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA Specification 2604, High Performance Organic Coatings on Aluminum o Type: Factory Applied, High Performance, 50% Polyvinylidene Fluoride (PVDF) Coating formulated by a licensed paint manufacturer, and applied by Paint Manufacturer's Warranty-Approved Applicator o Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic surface soils, remove residual oxides, followed by a Chrome Phosphate or Chromate Coating to ensure adhesion to the aluminum o Specify color code, e.g. UC 40577(Duranar Black) Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500 ); o Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA Specification 2605, Superior Performing Organic Coatings on Aluminum o Type: Factory Applied, High Performance, 70% Polyvinylidene Fluoride (PVDF) Coating formulated by a licensed paint manufacturer, and applied by Paint Manufacturer's Warranty-Approved Applicator o Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic surface soils, remove residual oxides, followed by a Chrome Phosphate or Chromate Coating to ensure adhesion to the aluminum o Specify color code, e.g. UC 40577(Duranar Black) PRODUCT PLACEMENT PREPARATION WORK Ensure openings are of proper size, and are plumb, square, level and in the proper location and alignment INSTALLATION Align installed assembly plumb and level, free of warp or twist Maintain dimensional tolerances, aligning with adjacent work Seal joints between framing and building structure watertight Follow guidelines in Pittco Fabrication, Sealant and Erection Brochure START-UP AND OPERATION Not Applicable OWNER'S MAINTENANCE INSTRUCTIONS Wash surfaces with warm water and mild soap; wipe clean, at least once a year 7
10 NON-THERMAL PRODUCT DESCRIPTION Corporate Identification Pittco Architectural Metals, Inc 150 Landmeier Road Elk Grove Village, Illinois Tel: (847) Fax: (847) Toll-Free: (800) Internet: Technical Services Available Toll-Free: (800) Classification and Filing MasterFormat Subset of Section Metal Framed Storefronts UniFormat Section B200 - (exterior entrance frames) or C1020 (interior entrance frames) 8
11 PRODUCT DESCRIPTION NON-THERMAL BASIC USES / RELATED USES Framing is designed for flush, center glazed storefront assembly Vertical mullions are typically open back aluminum members, with solid face and flush closure side plates forming tubular members for use on single spans Horizontal mullions are of hollow aluminum with removable glazing stops Glazing is insulating glass unit or single pane with adapters Corners are available for 90 and 15 degrees Glass may be transparent, opaque, or decorative types Framing is intended for one story applications Framed assembly may be fitted to most rigid and stable framed opening assemblies PRODUCT ATTRIBUTES AND CHARACTERISTICS Aluminum frame members are thermally improved Framing and glazing stops are designed for glass and panels Wind pressure resistance and pressure equalization are standard within the frame assembly Weep containment and condensate water collection and drainage to the exterior at concealed weeps are standard Integral door frames are available SELECTION CRITERIA Quality, economy, and good performance are provided at a reasonable cost Framing is designed for Interior or exterior environments APPLICABLE STANDARDS, RELATED REFERENCES AA (Aluminum Association) - Designation System for Aluminum Finishes AAMA SFM Aluminum Storefront and Entrance Manual AAMA Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors using Dynamic Pressure AAMA Voluntary Specification for Anodized Architectural Aluminum AAMA Voluntary Test Method for Thermal Transmittance and Condensation Resistance of Windows, Doors, and Glazed Wall Sections AAMA Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels AAMA Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels ASTM A12/A12M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products ASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate ASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric] ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube ASTM B221M - Standard Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube [Metric] 9
12 THERMAL PRODUCT DESCRIPTION ASTM E28 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under Specified Pressure Differences Across the Specimen ASTM E0 - Standard Test Method for Structural Performance of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference ASTM E1 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference QUALITY, TESTS, CERTIFICATIONS, AND APPROVALS Air Infiltration: Maximum leakage of 0.02 cfm/sq ft. when measured in accordance with ASTM E28 at a test pressure of 6.24 psf Static Water Leakage: No uncontrolled leakage, when measured in accordance with ASTM E1 at a test pressure difference of 12.0 psf Dynamic Water Leakage: No uncontrolled leakage, when measured in accordance with AAMA at a test pressure difference of 12.0 psf Structural Performance: Maximum deflection less than 1/175 of the span length and no damage to the assembly, when measured in accordance with ASTM E0 at a test pressure of 25 psf Condensation Resistance Factor (CRF): 58 when measured in accordance with AAMA 150 with clear 1 insulated glass unit (1/4, 1/2, 1/4) Insulation U-Factor: 0.59 BTU/hr/sq ft/degrees F when measured in accordance with AAMA 150 with clear 1 insulated glass unit (1/4, 1/2, 1/4) PACKAGING, HANDLING, AND PROTECTION INSTRUCTIONS Packaged in specially designed heavy cartons or shipped pre-fabricated and assembled SPECIAL WARRANTY One (1) year LIMITATIONS Framing is limited to applications of one story in height Not intended for continuous members for multiple floor applications SAFETY PRECAUTIONS Normal precautions required AVAILABILITY Framing is available in all regions of USA - refer to Internet web site for locations and addresses of distributors COST Varies with elevation, configuration and finish desired 10
13 PRODUCT DESCRIPTION THERMAL PRODUCT PROPERTIES MATERIAL, COMPOSITION AND DESIGN Aluminum: 606-T6 alloy and temper, to ASTM B221 or ASTM B221M Fasteners: Stainless steel, or zinc plated carbon steel Perimeter Anchors: Aluminum, or steel that will be isolated from aluminum components Glazing Gaskets: Wedge-type, Ethylene Propylene Diene Monomer (EPDM) rubber with non-stretch cord Glass Stops: Snap-in type Thermal Barrier: Poured and Debridged Polyurethane and Thermal Slots SHAPE AND DIMENSIONS Frame Size: 2 x 4-1/2 inch Glass Edge Bite: /8 inch Glazing Thickness Accepted: 1/8 inch to 1-1/8 inch in increments of 1/16 inch except 7/16 inch, 9/16 inch, 11/16 inch, and 1/16 inch SHOP FABRICATION AND ASSEMBLY Provide for flush glazing on all sides with no projecting stops Configurations: Two-piece snap together mullions Solid tubular mullions, assembled to specially designed shear block clips Accessories: Expansion Mullions Corner Mullions Open Back Perimeter Members Integral Door Frames Flashing, Subsills Head Receptor Heavy Duty Mullions Standard Steel Reinforcing Available COLORS AND TEXTURES Architectural anodic coating, in accordance with AAMA 611; o Aluminum Association Designation. AA-M10C22A1 - Class II - (Pittco #42 Clear) AA-M10C22A41 - Class I - (Pittco #4 Clear) AA-M10C22A44 - Class I - (Pittco #59 Champagne) AA-M10C22A44 - Class I - (Pittco #60 Light Bronze) AA-M10C22A44 - Class I - (Pittco #61 Medium Bronze) AA-M10C22A44 - Class I - (Pittco #62 Dark Bronze) AA-M10C22A44 - Class I - (Pittco #6 Black) 11
14 THERMAL PRODUCT DESCRIPTION Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500 ); o Finish on exposed aluminum shall be compliant with the performance standards set forth in AAMA 2605, Superior Performing Organic Coatings on Aluminum. o Type: Factory Applied - High Performance, 70% Polyvinylidene Fluoride (PVDF) coating based on Elf Atochem, Inc. Kynar 500 or Ausimount USA, Inc. Hylar 5000 resin, formulated by a Licensed Paint Manufacturer and applied by the Paint Manufacturer's Warranty Approved Applicator. o Pre-treatment: Applicator to pre-treat the aluminum with solutions to remove Organic and Inorganic Surface Soils and Residual Oxides, followed by a Chrome Phosphate Conversion Coating, at a minimum 40 mg/sq ft to ensure adhesion of paint to aluminum. o Specify color code, e.g. UC 40577(Duranar Black) Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500 ); o Finish on exposed aluminum shall be compliant with the performance standards set forth in AAMA 2604, High Performance Organic Coatings on Aluminum. o Type: Factory Applied - High Performance, 50% Polyvinylidene Fluoride (PVDF) coating based on Elf Atochem, Inc. Kynar 500 or Ausimount USA, Inc. Hylar 5000 resin, formulated by a Licensed Paint Manufacturer and applied by the Paint Manufacturer's Warranty Approved Applicator. o Pre-treatment: Applicator to pre-treat the aluminum with solutions to remove Organic and Inorganic Surface Soils and Residual Oxides, followed by a Chrome Phosphate Conversion Coating, at a minimum 40 mg/sq ft to ensure adhesion of paint to aluminum. o Specify color code, e.g. UC 40577(Duranar Black) PRODUCT PLACEMENT PREPARATION WORK Ensure openings are of proper size, and are plumb, square, level and in the proper location and alignment INSTALLATION Align installed assembly plumb and level, free of warp or twist Maintain dimensional tolerances, aligning with adjacent work Seal joints between framing and building structure watertight Follow guidelines in Pittco Fabrication, Sealant and Erection Brochure START-UP AND OPERATION Not Applicable OWNER'S MAINTENANCE INSTRUCTIONS Wash surfaces with warm water and mild soap; wipe clean, at least once a year 12
15 PRODUCT DESCRIPTION THERMAL Corporate Identification Pittco Architectural Metals, Inc 150 Landmeier Road Elk Grove Village, Illinois Tel: (847) Fax: (847) Toll-Free: (800) Internet: Technical Services Available Toll-Free: (800) Classification and Filing MasterFormat Subset of Section Metal Framed Storefronts UniFormat Section B200 - (exterior entrance frames) or C1020 (interior entrance frames) 1
16 EXPLODED VIEW SCREW SPLINE ASSEMBLY THE SCREW SPLINE SYSTEM ALLOWS A FRAME TO BE INSTALLED FROM UNITIZED ASSEMBLIES. SCREWS ARE DR THROUGH THE BACK OF THE VERTICALS INTO SPLINES EXTRUDED IN THE HORIZONTAL FRAMING MEMBERS. INDIV UNITS ARE THEN SNAPPED TOGETHER TO FORM A COMPLETE FRAME OPEN BACK MULLION SNAP-IN FILLER HEAD HORIZONTAL GLASS STOP SILL GLASS STOP SHEAR BLOCK ASSEMBLY THE SHEAR BLOCK METHOD OF FABRICATION IS AN ALTERNATE METHOD OF FABRICATION. HORIZONTA ARE ATTACHED TO THE VERTICAL MULLIONS WITH SHEAR BLOCKS. THIS METHOD MUST BE USED WIT TUBULAR VERTICAL MULLIONS. OPEN BACK MULLION SNAP-IN FILLER SHEAR BLOCK HEAD SHEAR BLOCK HORIZONTAL GLASS STOP SILL GLASS STOP 14
17 TYPICAL FRAMING DETAILS (Outside Glazed) NON-THERMAL (JAMB) (PERIMETER FILLER) SCREW SPLINE (JAMB) (GLAZING FILLER) (JAMB) (PERIMETER FILLER) SHEAR BLOCK (JAMB) (GLAZING FILLER) 1 JAMB 2 VERTICAL 1 JAMB 2 VERTICAL HEAD (HEAD) (PERIMETER FILLER) HEAD (HEAD) (PERIMETER FILLER) (SHEAR BLOCK) 4 HORIZONTAL (HORIZONTAL) 2-01 (GLASS STOP) 4 HORIZONTAL (HORIZONTAL) 2-01 (GLASS STOP) (SHEAR BLOCK) 5 SILL (SILL) 2-01 (GLASS STOP) (PERIMETER FILLER) (SUB-SILL) 5 SILL (SILL) 2-01 (GLASS STOP) (PERIMETER FILLER) (SUB-SILL) (SHEAR BLOCK) D1 DETAILS
18 NON-THERMAL TYPICAL FRAMING DETAILS (Inside Glazed) (JAMB) (PERIMETER FILLER) SCREW SPLINE (JAMB) (GLAZING FILLER) (JAMB) (PERIMETER FILLER) SHEAR BLOCK (JAMB) (GLAZING FILLER) 1 JAMB 2 VERTICAL 1 JAMB 2 VERTICAL HEAD (HEAD) (GLASS STOP) (PERIMETER FILLER) HEAD (HEAD) (GLASS STOP) (PERIMETER FILLER) (SHEAR BLOCK) 4 HORIZONTAL (HORIZONTAL) (GLASS STOP) 4 HORIZONTAL (HORIZONTAL) (GLASS STOP) (SHEAR BLOCK) 5 SILL (SILL) (PERIMETER FILLER) (SUB-SILL) 5 SILL (SILL) (PERIMETER FILLER) (SUB-SILL) 2-04 (SHEAR BLOCK) D2 DETAILS
19 CORNER AND OPTIONAL DETAILS NON-THERMAL OUTSIDE CORNER 90 INSIDE CORNER 15 CORNER HEAVY WALL MULLION HEAVY WALL MULLION w/ OPTIONAL STEEL EXPANSION MULLION ADJUSTABLE MULLION HEAD RECEPTOR " x 6" HORIZONTAL " x 6" SILL D DETAILS
20 SINGLE THERMAL TYPICAL FRAMING DETAILS (Outside Glazed) (JAMB) (PERIMETER FILLER) SCREW SPLINE (JAMB) (GLAZING FILLER) (JAMB) (PERIMETER FILLER) SHEAR BLOCK (JAMB) (GLAZING FILLER) 1 JAMB 2 VERTICAL 1 JAMB 2 VERTICAL HEAD (HEAD) (PERIMETER FILLER) HEAD (HEAD) (PERIMETER FILLER) (SHEAR BLOCK) 4 HORIZONTAL (HORIZONTAL) 2-01 (GLASS STOP) 4 HORIZONTAL (HORIZONTAL) 2-01 (GLASS STOP) (SHEAR BLOCK) 5 SILL D4 DETAILS (SILL) 2-01 (GLASS STOP) (PERIMETER FILLER) (SUB-SILL) 5 SILL (SILL) 2-01 (GLASS STOP) (PERIMETER FILLER) (SUB-SILL) (SHEAR BLOCK)
21 TYPICAL FRAMING DETAILS (Inside Glazed) SINGLE THERMAL (JAMB) (PERIMETER FILLER) SCREW SPLINE (JAMB) (GLAZING FILLER) (JAMB) (PERIMETER FILLER) SHEAR BLOCK (JAMB) (GLAZING FILLER) 1 JAMB 2 VERTICAL 1 JAMB 2 VERTICAL HEAD (HEAD) (GLASS STOP) (PERIMETER FILLER) HEAD (HEAD) (GLASS STOP) (PERIMETER FILLER) (SHEAR BLOCK) 4 HORIZONTAL (HORIZONTAL) (GLASS STOP) 4 HORIZONTAL (HORIZONTAL) (GLASS STOP) (SHEAR BLOCK) 5 SILL (SILL) (PERIMETER FILLER) (SUB-SILL) 5 SILL (SILL) (PERIMETER FILLER) (SUB-SILL) 2-04 (SHEAR BLOCK) D5 DETAILS
22 SINGLE THERMAL CORNER AND OPTIONAL DETAILS OUTSIDE CORNER 90 INSIDE CORNER 15 CORNER HEAVY WALL MULLION HEAVY WALL MULLION w/ OPTIONAL STEEL EXPANSION MULLION ADJUSTABLE MULLION HEAD RECEPTOR " x 6" HORIZONTAL " x 6" SILL D6 DETAILS
23 TYPICAL FRAMING DETAILS (Outside Glazed) DOUBLE THERMAL (JAMB) (PERIMETER FILLER) SCREW SPLINE (JAMB) (GLAZING FILLER) (JAMB) (PERIMETER FILLER) SHEAR BLOCK (JAMB) (GLAZING FILLER) 1 JAMB 2 VERTICAL 1 JAMB 2 VERTICAL HEAD (HEAD) (PERIMETER FILLER) HEAD (HEAD) (PERIMETER FILLER) (SHEAR BLOCK) 4 HORIZONTAL (HORIZONTAL) 2-01 (GLASS STOP) 4 HORIZONTAL (HORIZONTAL) 2-01 (GLASS STOP) (SHEAR BLOCK) 5 SILL (SILL) 2-01 (GLASS STOP) (PERIMETER FILLER) (SUB-SILL) 5 SILL (SILL) 2-01 (GLASS STOP) (PERIMETER FILLER) (SUB-SILL) (SHEAR BLOCK) D7 DETAILS
24 DOUBLE THERMAL TYPICAL FRAMING DETAILS (Inside Glazed) (JAMB) (PERIMETER FILLER) SCREW SPLINE (JAMB) (GLAZING FILLER) (JAMB) (PERIMETER FILLER) SHEAR BLOCK (JAMB) (GLAZING FILLER) 1 JAMB 2 VERTICAL 1 JAMB 2 VERTICAL HEAD (HEAD) (GLASS STOP) (PERIMETER FILLER) HEAD (HEAD) (GLASS STOP) (PERIMETER FILLER) (SHEAR BLOCK) 4 HORIZONTAL (HORIZONTAL) (GLASS STOP) 4 HORIZONTAL (HORIZONTAL) (GLASS STOP) (SHEAR BLOCK) 5 SILL (SILL) (PERIMETER FILLER) (SUB-SILL) 5 SILL (SILL) (PERIMETER FILLER) (SUB-SILL) 2-04 (SHEAR BLOCK) D8 DETAILS
25 CORNER AND OPTIONAL DETAILS DOUBLE THERMAL OUTSIDE CORNER 90 INSIDE CORNER 15 CORNER HEAVY WALL MULLION HEAVY WALL MULLION w/ OPTIONAL STEEL EXPANSION MULLION ADJUSTABLE MULLION HEAD RECEPTOR " x 6" HORIZONTAL " x 6" SILL D9 DETAILS
26 1 ENTRANCE DETAILS SINGLE ACTING DOOR JAMBS (HEAD) 2-01 (GLASS STOP) (PERIMETER FILLER) 1 TRANSOM HEAD 6 TRANSOM JAMBS Jambs above transom bar are routed out to accept glass holding insert with or without steel reinforcing (TRANSOM HEAD) (SHEAR BLOCK) (SHEAR BLOCK) (TRANSOM HEAD) (SHEAR BLOCK) (SHEAR BLOCK) 2 DOOR HEAD 10 DOOR HEAD (MULLION) SINGLE ACTING DOOR JAMBS (MULLION) D10 BOTTOM RAIL
27 WINDLOAD CHARTS SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION NON-THERMAL A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUM SECTIONS. S1
28 NON-THERMAL SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION WINDLOAD CHARTS A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF A B C D E WITH STEEL S2 VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUM SECTIONS.
29 WINDLOAD CHARTS SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION NON-THERMAL A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF COMBINED SECTIONS ARE ANALYZED AS AN ASSEMBLY S
30 SINGLE THERMAL SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK WINDLOAD CHARTS A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF S4 VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUM SECTIONS.
31 WINDLOAD CHARTS SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK SINGLE THERMAL A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF A B C D E WITH STEEL VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUM SECTIONS. S5
32 SINGLE THERMAL SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK WINDLOAD CHARTS A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF COMBINED SECTIONS ARE ANALYZED AS AN ASSEMBLY S6
33 WINDLOAD CHARTS SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK DOUBLE THERMAL A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUM SECTIONS. S7
34 DOUBLE THERMAL SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK WINDLOAD CHARTS A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF A B C D E WITH STEEL S8 VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUM SECTIONS.
35 WINDLOAD CHARTS SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK DOUBLE THERMAL A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF COMBINED SECTIONS ARE ANALYZED AS AN ASSEMBLY S9
36 SYSTEM ANALYSIS CRITERIA: ALUMINUM: 606-T6 DEFLECTION LIMITS: L/175 FOR SPANS LESS THAN 1'-6" L/ /4" FOR SPANS GREATER THAN 1'-6" CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN /4" LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM) (FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING) SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK WINDLOAD CHARTS A B C D E A = 15 PSF B = 20 PSF C = 25 PSF D = 0 PSF E = 40 PSF A B C D E S10 VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUM SECTIONS.
37 SYSTEM ANALYSIS CRITERIA: DEADLOAD CHARTS NON-THERMAL ALUMINUM: 606-T6 HORIZONTAL OR DEADLOAD LIMITATIONS ARE BASED UPON 1/8" MAXIMUM ALLOWABLE DEFLECTION WITH 1" THICK INSULATED GLASS SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THE THERMAL BREAK THERMAL SECTIONS (HORIZONTAL) 2-01 (GLASS STOP) B A A = SETTING BLOCKS AT 1/8 POINTS B = SETTING BLOCKS AT 1/4 POINTS (HORIZONTAL) (GLASS STOP) B A S11
38 SYSTEM ANALYSIS CRITERIA: SINGLE THERMAL DEADLOAD CHARTS ALUMINUM: 606-T6 HORIZONTAL OR DEADLOAD LIMITATIONS ARE BASED UPON 1/8" MAXIMUM ALLOWABLE DEFLECTION WITH 1" THICK INSULATED GLASS SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THE THERMAL BREAK THERMAL SECTIONS (HORIZONTAL) 2-01 (GLASS STOP) B A A = SETTING BLOCKS AT 1/8 POINTS B = SETTING BLOCKS AT 1/4 POINTS (HORIZONTAL) (GLASS STOP) B A S12
39 SYSTEM ANALYSIS CRITERIA: DEADLOAD CHARTS DOUBLE THERMAL ALUMINUM: 606-T6 HORIZONTAL OR DEADLOAD LIMITATIONS ARE BASED UPON 1/8" MAXIMUM ALLOWABLE DEFLECTION WITH 1" THICK INSULATED GLASS SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUAL SIMPLE SPAN CONDITION A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THE THERMAL BREAK THERMAL SECTIONS (HORIZONTAL) 2-01 (GLASS STOP) B A A = SETTING BLOCKS AT 1/8 POINTS B = SETTING BLOCKS AT 1/4 POINTS (HORIZONTAL) (GLASS STOP) B A S1
40 SECTION PROPERTIES STRUCTURAL PROPERTIES of TMS 152 NON-THERMAL FRAMING Part Number Ix Sx Iy Sy (Steel) STRUCTURAL PROPERTIES of TMS 152T SINGLE-THERMAL FRAMING Part Number Ix Sx Iy Sy (Steel) S14
41 SECTION PROPERTIES STRUCTURAL PROPERTIES of TMS 152XT DOUBLE-THERMAL FRAMING Part Number Ix Sx Iy Sy (Steel) S15
42 THERMAL CHARTS T1
43 THERMAL CHARTS T2
City of San Diego, CWP Guidelines
PART 1 -- GENERAL SECTION 08520-1.1 WORK OF THIS SECTION City of San Diego, CWP Guidelines A. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens,
More informationRAM Industries 8600 Commerce Park Dr Houston, TX 77036 Tel: 281-495-9056 Fax: 281-495-6778 www.ramwindows.com
SERIES 900 CASEMENT WINDOW Page 1 of 6 RAM Industries 8600 Commerce Park Dr Houston, TX 77036 Tel: 281-495-9056 Fax: 281-495-6778 www.ramwindows.com SPECIFICATION GUIDE SERIES 900 CASEMENT WINDOW RAM Industries
More informationJANUARY, 2016 TR-7100 Windows (Fixed) 1 EC 97909-071 085113 ALUMINUM WINDOWS Guide Specs
JANUARY, 2016 TR-7100 Windows (Fixed) 1 EC 97909-071 085113 ALUMINUM WINDOWS Guide Specs SECTION 085113 ALUMINUM WINDOWS This suggested guide specification has been developed using the current edition
More informationSECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS. System 402 Flush-Glazed Screw Spline Storefront
PART 1 GENERAL 1.01 Work Included SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS System 402 Flush-Glazed Screw Spline Storefront A. Furnish and install aluminum architectural storefront system
More informationSeries 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window
Windows Curtain Walls Entrances Storefronts Series 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window Configurations XO OX XOX Fixed Series 3502 retains an AAMA
More informationEDD-401. Stationary Louver Dual Drainable Blade. Application and Design. Standard Construction
Application and Design is a weather louver designed to protect air intake and exhaust openings in building exterior walls. Design incorporates a drainable head member and stationary horizontal blades to
More informationSECTION 08560 SERIES 1500 VINYL PATIO DOORS
SERIES 1500 VINYL PATIO DOORS PART 1 GENERAL 1.1 SECTION INCLUDES A. Patio Doors 1.2 RELATED SECTIONS A. Section 05450: Cold Formed Metal Framing. B. Section 06100: Rough Carpentry. C. Section 06200: Finish
More informationPERFORMANCE TEST REPORT. Rendered to: UNITED STATES ALUMINUM CORPORATION. SERIES/MODEL: 450 Center Glaze PRODUCT TYPE: Aluminum Curtain Wall
Architectural Testing PERFORMANCE TEST REPORT Rendered to: UNITED STATES ALUMINUM CORPORATION SERIES/MODEL: 450 Center Glaze PRODUCT TYPE: Aluminum Curtain Wall Title Summary of Results Air Infiltration
More informationMOCK-UP TEST REPORT. Rendered to: TUBELITE, INC. PROJECT: 200 Series Curtain Wall Mock-Up
MOCK-UP TEST REPORT Rendered to: TUBELITE, INC. PROJECT: 200 Series Curtain Wall Mock-Up Report No: 85616.01-120-32 Test Completion Date: 01/15/09 Report Date: 02/11/09 Record Retention End Date: 01/15/13
More informationFEBRUARY, 2016 2500 UT Unitwall System 1 EC 97909-074 084413 GLAZED ALUMINUM CURTAIN WALLS Guide Specs
FEBRUARY, 2016 2500 UT Unitwall System 1 EC 97909-074 084413 GLAZED ALUMINUM CURTAIN WALLS Guide Specs Kawneer Company, Inc., 2015 SECTION 084413 GLAZED ALUMINUM CURTAIN WALLS This suggested guide specification
More informationSECTION 07 42 13 METAL WALL PANELS
Mitsubishi Plastics Composites America, Inc. 401 Volvo Parkway Chesapeake, VA 23320 Phone: (800) 422-7270 Fax: (757) 436-1896 E-mail: info@alpolic.com www.alpolic-northamerica.com This MANU-SPEC utilizes
More informationSECTION 08 5656 GUARDA SECURITY WINDOW SCREENS
Page 1 of 5 SECTION 08 5656 GUARDA SECURITY WINDOW SCREENS Guarda Security Window Screens in this specification are appropriate for use in windows, storefronts, curtain walls, vents, and any other applications
More informationSECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2
More informationMIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Report No.: B8049.01-401-18. Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida
Architectural Testing MIAMI-DADE COUNTY PERFORMANCE TEST REPORT Report No.: B8049.01-401-18 Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida PRODUCT TYPE: Aluminum Storefront with Double Doors SERIES/MODEL:
More informationPART 1 PROJECT DESCRIPTION 1.01 GENERAL INFORMATION
Detailed Specifications for Window Replacement for the Metropolitan Sewer District of Greater Cincinnati Little Miami Wastewater Treatment Plant 225 Wilmer Ave. Cincinnati, OH 45226 Administration Building,
More informationTEST REPORT. Rendered to: TFC A DIVISION OF CENTURION INDUSTRIES, INC. Garrett, Indiana
Architectural Testing TEST REPORT Report No.: D0162.02-201-44 Rendered to: TFC A DIVISION OF CENTURION INDUSTRIES, INC. Garrett, Indiana PRODUCT TYPE: Pressure Equalized Rainscreen SERIES/MODEL: 4 mm Composite
More informationSECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK
SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. This section covers the pre-finished, pre-fabricated Architectural standing seam roof system. All metal trim,
More informationK200 SERIES(CW40) (Formerly #1300 Series) SLIDER/CENTER VENT SLIDER/ END VENT SLIDER 2 3/8 FRAME DEPTH FEATURES
K200 SERIES(CW40) (Formerly #1300 Series) SLIDER/CENTER VENT SLIDER/ END VENT SLIDER 2 3/8 FRAME DEPTH FEATURES 1.) Available Configurations -XO, OX, OXO, OR XOX 2.) Main frame / Sash -Fin seal wool pile
More informationSECTION 6. Glass Storefront Doors:
SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail
More informationWATER LEAKAGE IN GLAZED CURTAIN WALL SYSTEMS:
WATER LEAKAGE IN GLAZED CURTAIN WALL SYSTEMS: BY WILLIAM D. SMITH Figure 1 Four Corporate Center, Franklin, TN. Architect: Little & Associates,Charlotte, NC. Gen. Contractor: Ray Bell Const. Co., Nashville,
More informationPART 1 GENERAL 1.1 SECTION INCLUDES
J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including
More informationSun Windows General Information Sun New Construction Window Installation Instructions
Sun Windows General Information Section 1 G F H H H A. Apply Weather Resistive Barrier B. Apply Sill Flashing Tape C. Place Waterproof Sill Shims D. Caulk Back of Nail Fin Sides & Top, Set Window, Fasten
More informationSapa: SECTION 05520 ARCHITECTURAL ALUMINUM HANDRAILS AND RAILINGS
PART 1 GENERAL Sapa: SECTION 05520 ARCHITECTURAL ALUMINUM HANDRAILS AND RAILINGS 1.1 SECTION INCLUDES A. Aluminum and Glass Handrails B. Aluminum Railings 1.2 RELATED SECTIONS A. Section 05700 - Ornamental
More informationSECTION 07 61 13 STANDING SEAM METAL ROOFING
SECTION 07 61 13 STANDING SEAM METAL ROOFING PART 1 GENERAL 1.01 SCOPE OF WORK A. The Work shall include all labor, materials, equipment and supervision required to complete the work of the above referenced
More informationMANCHESTER SERIES(SGD-R35) SLIDING GLASS DOOR 5 5/8 FRAME DEPTH
MANCHESTER SERIES(SGD-R35) SLIDING GLASS DOOR 5 5/8 FRAME DEPTH FEATURES 1.) Available Configurations -Sliding Glass Door -Geometric shapes -OX, XO, OXO, OXXO, XOO, OOX (as viewed from exterior) 2.) Main
More informationASTM E 1886 / ASTM E 1996 AND ASTM E 283, ASTM E 330, ASTM E 331 TEST REPORT. Rendered to: BEKAERT SPECIALTY FILMS, LLC
ASTM E 1886 / ASTM E 1996 AND ASTM E 283, ASTM E 330, ASTM E 331 TEST REPORT Rendered to: BEKAERT SPECIALTY FILMS, LLC SERIES/MODEL: Panorama 8-mil Film PRODUCT TYPE: Fixed Window with Applied Film This
More informationSECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
More informationWindow Installation Instructions
Caution The correct installation methods of windows in full frame or insert applications is critical towards achieving the tested performance of the window and longterm enjoyment and energy savings for
More informationHow To Test For An Architectural Test
Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: CORAL ARCHITECTURAL PRODUCTS SERIES/MODEL: PW 256 with Door Openings PRODUCT TYPE: Aluminum Impact Resistant Curtain Wall System
More informationSECTION 08 53 13 VINYL WINDOWS. A. The General Conditions, Supplementary Conditions, and Division 01 - Requirements apply.
SECTION 08 53 13 VINYL WINDOWS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 - Requirements apply. 1.2 SECTION INCLUDES A. Double
More informationTable of Contents PART 1 WINDOW SELECTION GUIDE. Window and Door Selection Guide
VOLUME 1 - WINDOWS AND DOORS Window and Door Selection Guide PART 1 WINDOW SELECTION GUIDE WSG-11 PART 2 - PERFORMANCE SPECIFICATIONS Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows
More informationASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: Atrium Companies, Inc. SERIES/MODEL: 50/305 HS PRODUCT TYPE: Vinyl Horizontal Slider
ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: Atrium Companies, Inc. SERIES/MODEL: 50/305 HS PRODUCT TYPE: Vinyl Horizontal Slider Report No.: Test Date: 5/21/07 Through: 5/23/07 Report Date: 5/30/07
More informationClad Direct Glaze Window Installation Instructions
Clad Direct Glaze Window Installation Instructions Sill flashing and sealing: 2. An overview of the proper flashing sequence is shown in figure 1. Please read entire installation instructions carefully
More informationTEST REPORT. Report No.: B3404.01-801-47. Rendered to: CROFT, LLC. Magnolia, Mississippi. PRODUCT TYPE: Aluminum Single Hung Window SERIES/MODEL: 95
Architectural Testing TEST REPORT Report No.: B3404.01-801-47 Rendered to: CROFT, LLC. Magnolia, Mississippi PRODUCT TYPE: Aluminum Single Hung Window SERIES/MODEL: 95 SPECIFICATION: AAMA/WDMA/CSA 101/I.S.2/A440-08,
More informationMiami-Dade Qualified Drainable Blade Louvered Penthouse
Application and Design is a gravity intake or exhaust louvered penthouse. Model incorporates high performance horizontal drainable style blades. Meets the performance requirements established by the Florida
More informationDIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS
DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the contract, including general and supplementary conditions and other Division 1
More informationIntroduction...COMB-2 Design Considerations and Examples...COMB-3
SECTION DIRECTORY General Information Introduction...COMB-2 Design Considerations and Examples...COMB-3 Combination Assembly Recommendations and Limitations Composite Configurations...COMB-4 Typical Sealant
More informationGUIDELINE SPECIFICATIONS
GUIDELINE SPECIFICATIONS GORDON SOFFIT-SHIELD - An Exterior Metal Soffit System DIVISION 05 5800 or DIVISION 07 7700 Note To Specifier: SOFFIT-SHIELD should be installed by tradesmen that are experienced
More informationPERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY
PERFORMANCE TEST REPORT Rendered to: GLASSCRAFT DOOR COMPANY SERIES/MODEL: Buffalo Forge Steel Doors / Round Top Single PRODUCT TYPE: In-swing Round Top Single Door RH-4 Title Uniform Load Deflection Test
More informationJANUARY, 2016 NX-8900 Terrace Doors 1 EC 97909-071 084113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS Guide Specs
JANUARY, 2016 NX-8900 Terrace Doors 1 EC 97909-071 084113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS Guide Specs SECTION 084116 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS This suggested guide specification
More informationRACO Interior OfficeFronts. SolutionsII Typical Details. SolutionsII
SolutionsII 1 SolutionsII Product Typical Overview Details I. GENERAL DESCRIPTION Work Included: Furnish all necessary materials, labor and equipment for the complete installation of interior aluminum
More informationn Three 4 x 4 butt hinges per door - prevents wracking and assures smooth positive operation n Heavy duty 16 gauge steel frame
Weather Fin and bulb help keep bad weather outside and good air inside Windows: n Many light kits are available 1-LU 4 X 48 1-LE 16 X 16 1-LA 20 X 24 1-LI 20 X 24 1-B 22 X 36 1-LW 16 X 16 W/GRID 9-LB 22
More informationCLEAR-DIVISIONS CENTERFOLD
CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in
More informationDoor hardware may be specified in whole or in part in this section or in Section 08 71 00 Door Hardware; coordinate requirements.
Page 1 of 17 Manufacturer: U.S. Aluminum 2450 E. Vernon Ave. Los Angeles, California 90058-1802 Toll Free Phone: (800) 262-5151, Phone: (323) 268-4230 Toll Free Fax: (866) 262-3299 www.usalum.com GUIDE
More informationvinyl replacement windows LOOKING FOR VINYL REPLACEMENT WINDOWS? Standard Features easy, trouble-free operation. window material formulated and
vinyl replacement windows LOOKING FOR VINYL REPLACEMENT WINDOWS? We are confident that we carry a style and size to suit your application. You can be sure that your investment will add value to your home,
More informationINSTALLATION OF A BAY WINDOW
INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening
More informationTEST REPORT. Report No.: A9814.01 109 44. Rendered to: BAMCO INC. Middlesex, New Jersey. PRODUCT TYPE: Wall Cladding System SERIES/MODEL: Dry Concept
Architectural Testing TEST REPORT Report No.: A9814.01 109 44 Rendered to: BAMCO INC. Middlesex, New Jersey PRODUCT TYPE: Wall Cladding System SERIES/MODEL: Dry Concept AAMA 508 07, Voluntary Test Method
More informationGarden Windows Builders Vinyl
TABLE OF CONTENTS Specifications... 8-2 QuickSpecGuide... 8-3 Elevations/Sizes: 1/4 Scale GardenUnits... 8-4 Grille Patterns... 8-5 SectionDetails: 6 Scale... 8-6 December 2008 JELD-WEN reserves the right
More informationTEST REPORT. Rendered to: INTERNATIONAL WINDOW Hayward, California. PRODUCT TYPE: Aluminum Hopper SERIES/MODEL: 7222
Architectural Testing TEST REPORT Report No.: C2375.01-301-44 Rendered to: INTERNATIONAL WINDOW Hayward, California PRODUCT TYPE: Aluminum Hopper SERIES/MODEL: 7222 SPECIFICATIONS: AAMA/WDMA/CSA 101/I.S.2/A440-05,
More information2.02. Specifications. General. Products. Execution. Offset Pivots P-694 Top and Bottom Pivots
2.02 Standard Specifications General Entrances Description Furnish all necessary materials, labor and equipment for the complete installation of aluminum entrance doors, door frames and hardware as shown
More informationPERFORMANCE TEST REPORT. Rendered to: BAMCO INC. PRODUCT TYPE: ACM Wall Panel Systems
PERFORMANCE TEST REPORT Rendered to: BAMCO INC. PRODUCT TYPE: ACM Wall Panel Systems Summary of Results Title Test Specimen #1 Test Specimen #2 Air Infiltration
More informationC. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction.
SECTION 081216 - INTERIOR ALUMINUM DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationQuality Assurance and Diagnostic Water Leakage Field Check of Installed Storefronts, Curtain Walls and Sloped Glazing Systems
Method of Test Committee Approval Product Group Approval Approved via 5/21/15 MOT CC Out for Ballot (#805-15) PUBLICATION NO. AAMA 501.2-XX DRAFT #2 DATED 5/21/15 Quality Assurance and Diagnostic Water
More informationNanaWall SL73 - Thermally Broken Aluminum Framed Hurricane Rated Folding System with Miami Dade County, Florida NOA
NanaWall SL73 - Thermally Broken Aluminum Framed Hurricane Rated Folding System with Miami Dade County, Florida NOA ❶ PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Sliding/folding aluminum and glass
More informationDESIGN AND CONSTRUCTION GUIDELINES AND STANDARDS DIVISION 8 DOORS AND WINDOWS 08 50 00 WINDOWS
SECTION INCLUDES Metal Windows Vinyl/Aluminum Clad Wood Windows Solid Fiberglass and Vinyl Windows Wood Windows (Historic Preservation only) RELATED SECTIONS 02 83 00 Lead Paint Remediation 06 10 00 Rough
More informationMarch 14, 2007. Installation of Bay, Bow and Garden Windows
March 14, 2007 Re: Installation of Bay, Bow and Garden Windows Attached are the Atrium Companies, Inc recommendation for the installation of bay, bow and garden windows. These instructions were developed
More informationCLEAR-DIVISIONS VARIOFOLD
CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the
More informationOpen Up Your Space, Add Light Series 2050 and Series 2050i Garden Windows
Open Up Your Space, Add Light Series 2050 and Series 2050i Garden Windows Series 2050 Garden Window The Series 2050 standard garden window has an outstanding reputation for its distinctive design and excellent
More informationSECTION 07400 STANDING SEAM METAL ROOF
SECTION 07400 STANDING SEAM METAL ROOF PART 1 - GENERAL 1.01 SECTION INCLUDES A. Work described in this section includes pre-formed standing seam metal roofing system complete with clips, perimeter and
More informationSection 08520 - Aluminum Windows (4600 Series Specifications)
Section 08520 - Aluminum Windows (4600 Series Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for
More informationSECTION 07720 PREFORMED METAL STANDING SEAM ROOFING
SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING PART ONE GENERAL DESCRIPTION This section includes pre-formed standing seam metal roofing and related flashings, closures, trim and accessories including,
More informationInstaller Training and Certification Overview
Installer Training and Certification Overview Outline of This Presentation The Need for a Training Program The History of the Program Details of the Training Program The Certification Process The Need
More informationPERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY
Architectural Testing PERFORMANCE TEST REPORT Rendered to: GLASSCRAFT DOOR COMPANY SERIES/MODEL: Mahogany Entry Door PRODUCT TYPE: 6' x 8' Double Outswing Hardwood TDL Door with Half Circle TDL Transom
More information- - - - Steel Panel Frame. Exterior Steel Sheeting. Optional Rigid Insulation. Optional Steel Insulation Liner
The Kelly Klosure pre-framed modular panel has 4 components that are factory finished to create an easy and versatile bolt-together system in the field. Steel Panel Frame Exterior Steel Sheeting Optional
More informationGarden Window. Montecito Series Vinyl Garden Window Architectural Manual
Montecito Series Vinyl The offers the outstanding insulating properties, low maintenance, and contemporary aesthetic appeal only vinyl can provide. Available in White and Tan homogenous window frames,
More informationCasement/Awning Window Parts Reference Catalog
Casement/Awning Window Parts Reference Catalog (Includes Miscellaneous Parts for Eyebrow Casement and Garden Bay Windows) #1028654 (Revised 03/02) Weather Shield Mfg., Inc. Medford, WI 54451 715/748-2100
More informationPhoenix-3W Series One-Way Security Revolving Doors
Phoenix-3W Series One-Way Security Revolving Doors ONE-WAY SECURITY REVOLVING DOOR SPECIFICATIONS ARCHITECTURAL SPECIFICATIONS Phoenix-3W Series One-Way Security Revolving Door Division 8 Doors and Windows
More informationglass & Glazing Products
glass & Glazing Products WallMaker Create an unlimited variety of bright, beautiful and secure interior environments with the easy-to-install Stylmark WallMaker glass wall system. This versatile system
More informationIn the Fall 2002 issue of HHE News I examined
Choosing Replacement Windows 1 For Your Home Mark Pierce In the Fall 2002 issue of HHE News I examined reasons for, and against, replacing older windows with new, energy efficient windows. That article
More informationAssessing Curtain Walls
Assessing Curtain Walls Considerations and Best Practices Paul E Beers GCI Consultants, LLC pbeers@gciconsultants.com What is a Curtain Wall System? A curtain wall system is an outer covering of a building
More informationSpecifiers: Click on the icon in the WORD toolbar to reveal detailed instructions SECTION 07 42 13 METAL WALL PANELS
Specifiers: Click on the icon in the WORD toolbar to reveal detailed instructions SECTION 07 42 13 METAL WALL PANELS Concealed Fastener Metal Wall Panels PART 1 - GENERAL 1.1 SECTION INCLUDES A. [Concealed
More informationPERFORMANCE TEST REPORT. Rendered to: ARCHITECTURAL METAL SOLUTIONS, INC.
PERFORMANCE TEST REPORT Rendered to: ARCHITECTURAL METAL SOLUTIONS, INC. SERIES/MODEL: AMS ARMOR-LOCK PRODUCT TYPE: STANDING SEAM METAL ROOF PANEL SYSTEM Report No: 97123.02-901-44 Test Date: 05/17/10
More informationBASIC FIRE DOOR REQUIREMENTS TECHNICAL DATA SHEET NO. 401
BASIC FIRE DOOR REQUIREMENTS SHEET NO. 401 Fire door openings are classified by their locations in the building. The location determines the length of exposure protection required, based on the potential
More informationPERFORMANCE TEST REPORT. Rendered to: TREMCO INCORPORATED. SERIES/MODEL: Proglaze ETA PRODUCT TYPE: Engineered Transition Assembly
PERFORMANCE TEST REPORT Rendered to: TREMCO INCORPORATED SERIES/MODEL: Proglaze ETA PRODUCT TYPE: Engineered Transition Assembly Title Summary of Results Air Infiltration
More informationCHAPTER 7: Building Systems ROOFING SYSTEMS
ROOFING SYSTEMS Purpose Examples 1. Shingle roof system 2. Metal roof with blanket insulation 3. Metal roof with rigid insulation 4. Built-up asphalt roof system 5. Single-ply roof system 6. Modified Bitumen
More informationWe urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.
Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden
More informationPreformed Metal Roofing and Siding
Page -1-1. GENERAL 1.1. Description This specification along with the drawings covers the furnishing of all material, products, equipment, accessories, tools, services, transportation, labor and supervision
More informationSample Calculations...V-CR-12. Door and Window Typical Combinations... V-CR-12 Horizontal and Vertical Typical Combinations...
SECTION DIRECTORY General Information Definitions...V-CR- Design Considerations...V-CR- Composite Configurations...V-CR-4 Design Considerations and Examples for Typical Window and Door Combinations...V-CR-5
More informationAC-3200 ALUMINUM PLATE SYSTEM (DRY JOINT)
ALUMINUM PLATE SYSTEM (DRY JOINT) C D E G P J L A H M B Q F A B C D E F G H J K L M N P Q R HORIZONTAL JOINT DETAIL VERTICAL JOINT DETAIL COPING DETAIL (1) COPING DETAIL (2) COPING DETAIL (3) OUTSIDE CORNER
More informationWINDOW PANNING AND TRIMS
OCTOBER, 2010 PANNING AND TRIMS GENERAL INFORMATION 1 EXTERIOR PANNING Panning is primarily used to cover the perimeters of existing building openings prior to the installation of replacement windows.
More informationResidential Garage Door Terminology
A Air Infiltration: The leakage or passage of air through a door system Anodize: A hard non-corrosive oxide film on the surface of aluminum Astragal: A compressible or deformable seal provided on the bottom
More informationALUMINUM Guide Spec: Standard Aluminum Windows & Doors
ALUMINUM Guide Spec: Standard Aluminum Windows & Doors Standard Aluminum Windows ALUMINUM WINDOWS - 08 51 13 With the thin lines that Migard s Aluminum Windows provide, they are ideal for both new construction
More informationSECTION 08600 POLYVINYL CHLORIDE (PVC) WINDOWS Paradigm Window Solutions 8381 Single Hung
SECTION 08600 POLYVINYL CHLORIDE (PVC) WINDOWS Paradigm Window Solutions 8381 Single Hung PART 1 GENERAL 1.1 APPLICABLE PUBLICATIONS: The publications listed below form a part of this specification to
More informationNFRC 102-2010 THERMAL PERFORMANCE TEST REPORT. Rendered to: CR LAURENCE CO., INC. SERIES/MODEL: 7500 Concealed Vent TYPE: Projecting (Awning)
NFRC 102-2010 THERMAL PERFORMANCE TEST REPORT Rendered to: CR LAURENCE CO., INC. SERIES/MODEL: 7500 Concealed Vent TYPE: Projecting (Awning) Summary of Results Standardized Thermal Transmittance (U-Factor)
More informationCLEAR-DIVISIONS APERTO
CLEAR-DIVISIONS Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS moveable glass wall system. The yellow highlighted areas in the
More informationSpecifications. Preformed Metal Wall and Roof Panels. Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023
Specifications Preformed Metal Wall and Roof Panels Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023 Section 07410 Preformed Metal Wall and Roof Panels Structural
More informationSPECIFICATION Aluminum Module Frames. Allowed anodization before fabrication for clear frames.
SPECIFICATION Allowed anodization before fabrication for clear frames. Page 2 of 9 1. SCOPE 1.1. This document provides general requirements for aluminum frames used in the assembly of photovoltaic modules.
More informationAAMA 2400-10. Standard Practice for Installation of Windows with a Mounting Flange in Open Stud Frame Construction for Low Wind/Water Exposure
A M E R I C A N A R C H I T E C T U R A L AAMA 2400-10 Standard Practice for Installation of Windows with a Mounting Flange in Open Stud Frame Construction for Low Wind/Water Exposure M A N U F A C T U
More informationInstallation Detailed installation instructions are provided which should be strictly followed.
Specification System 6 The Metal Technology Thermally-Broken Vertical Slide Window has been designed in such a way that its'attractive and clean lines will enhance all types of residential and commercial
More informationSECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS
1 SECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and
More informationROOF FLASHING SPRINGLOK FLASHING SYSTEM FEATURES & BENEFITS PRODUCT DESCRIPTION
SPRINGLOK SYSTEM PRODUCT DESCRIPTION FEATURES & BENEFITS Fry Reglet offers five flashing systems, each tailored for a particular type of substrate so you can get exactly what you need. SM Surface mounted
More informationfoot skylight) is enough to knock a worker off their feet. A 10 mph wind gust on a 5 x 6 skylight develops a wind force of 270 lbs.
Skylight Installation Instructions This document provides instruction and guidelines for installation of both curb mount (CM) and self flashing (SF) unit skylights on flat, pitched (> or equal to 3/12
More informationSuperform Products Ltd.
TYPICAL CORNER REINFORCING NOTE : SEE ENGINEERED REBAR SCHEDULES SUPPLIED BY THE MANUFACTURER STEEL REINFORCEMENT WALL CORNER 90 Copyright 2012 Sept. 2012 5.1.1 Rebar Spacing 6" 12" Max. Load LB./FT. 2000
More informationDisplay hidden notes to specifier. (Don't know how? Click Here) A. Advanced Upcoiling Security Grilles, power operated.
SECTION 08333 ADVANCED UPCOILING SECURITY GRILLE MODEL 600 ADV Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Advanced Upcoiling Security Grilles,
More informationConfort 26. Sliding Systems. Sapa Building System
Confort 26 Sliding Systems Sapa Building System Confort 26 is Sapa s thermally insulated sliding system for windows and doors. Available as two- and three-rail solution. Among its features, there are
More informationQuality Building Products for over 50 Years
Light Commercial Quality Building Products for over 50 Years Harvey Building Products is a leading manufacturer and distributor of high quality building products. We manufacture a complete line of superior
More informationAST M F 1642-04/GSA TS01 T EST R EPO R T. Rendered to: UNI T E D ST A T ES A L U M INU M
AST M F 1642-04/GSA TS01 T EST R EPO R T Rendered to: UNI T E D ST A T ES A L U M INU M SE RI ES/M O D E L : B W3250 PR O DU C T T YPE : Aluminum Combination Fixed Window Summary of Results Title Test
More informationEvaluating the Field Performance of Windows and Curtain Walls of Large Buildings
Best2 Airtightness of Buildings Session WB6-2 Evaluating the Field Performance of Windows and Curtain Walls of Large Buildings Mario D. Gonçalves, Patenaude-Trempe and Robert Jutras, Air-Ins Introduction
More informationEnhancing The Beauty And Value Of Your Home. Exclusive Patio Door Collection.
Enhancing The Beauty And Value f Your Home. Exclusive Patio Door Collection. Since 1985 North Star has been an industry leader in the manufacture of attractive and energy-efficient vinyl windows and patio
More informationAstragal: a vertical member placed at the meeting edges of a double door to provide a weather seal and may be used to anchor the fixed door.
Window and Door Dictionary AAMA: American Architectural Manufacturers Association. A national trade association that establishes voluntary standards for the window, door, and skylight industry. Ambient
More information