Design Object Library Guide
|
|
- Joan Pearson
- 7 years ago
- Views:
Transcription
1 Design Object Library Guide For Revit Objects Centre for Construction IT
2 Contents 1. Introduction Understanding the Revit s Family Editor Family Editor Tools Creating Mechanical Equipment with CP83 Symbol Recommended Workflow... 7 Planning... 8 Choosing a Family Template... 9 Create an Object Sub-categoty Creating the Object Framework Creating the Object Geometry Creating Solid 3D Geometry Creating CP83 2D Symbol Adding MEP Connectors Managing object Visibility Graphics Testing the Object into the Project References Revit Families Guide Library Creation Tutorial Videos Customizing Autodesk Seek Library to comply with the local standards Content Modification Page 2
3 1. Introduction This guide is intended to give concept in creating and modifying Revit objects to comply with the Singapore standards. This should be read in conjunction with Revit Families Guide to better understand some software terms used in the entire documents. Although any sketching and 2D or 3D modeling experience is helpful to understand how to work with families, before working with this guide, users should have a basic understanding of Revit MEP. If not, it is recommended to use the tutorials included in the software. In this guide, the user will learn: - how to create MEP objects from the scratch - how to create and incorporate CP83 2D symbols in the MEP objects - how to modify downloaded objects from the internet and other sources - how to load and use created objects into the project Page 3
4 2. Understanding the Revit s Family Editor The Family Editor is a graphical editing mode in Revit MEP that allows you to create objects to include in your project. To get started, choosing the correct template for the objects to be created should be considered. The template can include multiple views, such as plan and elevation views. The Family Editor has the same look and feel as the project environment in Revit MEP, but features different tools located on a single Home tab. Family Editor can be accessed through: Application Menu > New > Family Page 4
5 2.1 Family Editor Tools Family Category and Parameters (Home tab Family Category and Parameters) opens the Family Category and Parameters. You can create new family types or new instance and type parameters. Dimension tool (Annotate tab Dimension panel) add permanent dimensions to the family, in addition to ones that Revit MEP automatically creates as you draw the geometry. This is important if you wish to create different sizes of the object. Symbolic Line tool (Annotate tab Detail panel Symbolic Line) lets you draw lines that are meant for symbolic purposes only. For example, you might use symbolic lines to represent the flow direction for a pipe fitting. Symbolic lines are not part of the actual geometry of the object. Symbolic lines are visible parallel to the view in which you draw them. You can control symbolic line visibility on cut instances. Select the symbolic line, and click Modify Lines tab Visibility panel Visibility Settings. In the Family element visibility settings dialog, select Show only if instance is cut. Reference Plane tool (Home tab Datum panel Reference Plane) creates a reference plane, which is an infinite plane that serves as a guide for drawing lines and geometry. Reference Line tool (Home tab Datum panel Reference Line) creates a line similar to a reference plane, but that has logical start and end points. Text tool (Annotate tab Text panel Text) lets you add text notes to the family. This is typically used in an annotation object. Model Text tool (Home tab Model panel Model Text) lets you add signage to a building or letters to a wall. Section (View tab Create panel Section) lets you create a section view. Component tool (Home tab Model panel Component) selects the type of component to be inserted into the Family Editor. After you select this tool, the Type Selector becomes active and you can select a component. Symbolic Line tool (Annotate tab Detail panel Symbolic Line) lets you place 2D annotation drawing symbols. Detail Component tool (Annotate tab Detail panel Detail Component) lets you place a detail component. Masking Region tool (Annotate tab Detail panel Masking Region) lets you apply a mask that will obscure model elements when the object is used to create an element in a project. See Masking Regions in the Revit MEP 2012 Help. Page 5
6 Forms tool (Home tab Forms panel) provides access to tools that let you create solid and voids geometry in the object. Load into Project (Home tab Family Editor panel Load Into Project) lets you load a family directly into any open project or family. Page 6
7 3. Creating Mechanical Equipment with CP83 Symbol To create an object in revit, you need to define the geometry and size of the object using a family template that is provided in Revit MEP. You can then save the object as a separate Revit family file (.rfa file) and load it into any project. Depending on the complexity of the object, the creation process can be time-consuming. If you can identify an object that is similar to the one you want to create, you can save time and effort by copying, renaming, and modifying the existing object. The topics in this section apply to the creation of model (3D) objects, but some are relevant to 2D objects, including titleblocks, annotation symbols, and detail components. 3.1 Recommended Workflow Page 7
8 Planning Before creating the object, it is important to list down the object s requirements. Below are the requirement should be considered: Sizes Display in plan or in 3D such as symbols. Detail Hosting if necessary Non-geometry attributes such as Voltage, Capacity, etc Below is the example. Capacity Apparent Load Hosting CP83 Symbol 300KVA 2000KVA Face Base Page 8
9 Choosing a Family Template After you plan an object, your next step is to choose the base template that you will use. When you create an object, you are prompted to select a family template that corresponds to the type of element that the object will going to create. The template serves as a building block, containing the information that you need to start creating the object and that Revit MEP needs to place the object in projects. 1. Application Menu > New > Family 2. Choose Metric Generic Model face based.rft from the list of available templates. NOTE: If you are creating an annotation or titleblock object, click New Annotation Symbol or Title Block. Page 9
10 Create an Object Sub-categoty When you create an object, the template assigns it to a category that defines the default display of the object (line weight, line color, line pattern, and material assignment of the object geometry) when the object is loaded into a project. Placing the object in the right category can be done though the following steps: 1. From the Home Tab, choose Family Category and Parameters. 2. On the Family Category and Parameters dialog box, choose Mechanical Equipment. TIP: You can apply a drafting pattern to the object. When you create and define a subcategory to apply to the object, you can specify its surface and cut pattern materials to have a drafting Page 10
11 pattern. You cannot apply a model pattern to the object. Only flat or cylindrical surfaces can have drafting patterns. See Fill Patterns in the Revit MEP 2012 Help. Creating the Object Framework After planning the object s parameters, the next step is to create the object s framework. The framework is comprised of lines and parameters in which you later create the object geometry. It also defines the origin (insertion point) of elements that you create with the object. To create a framework for the object shown on planning stage, please follow below steps. 1. From the chosen template, add a reference line from point 1 to point 2. See the figure above. 2. In the temporary dimension, key-in 350mm distance from the reference plane. (green dotted line in the family editor window). 3. Mirror the 2 reference lines created to have a square with 700mm x 70mm size. This will be the face of the equipment. Page 11
12 Creating the Object Geometry You can use both 2- and 3-dimensional geometry to create the object. Create solid geometric shapes to represent the element that the object is intended to create. Use 2D linework to add detail to solid geometry in certain views or to create a symbolic plan representation of an element. Creating Solid 3D Geometry To create solid object geometry, you use 3-dimensional solid and void forms. Solid forms are 3D shapes that represent the solid geometry of object. 1. From the Home tab, choose Extrusion. On the property panel, key-in 25mm for the extrusion end. This will be the thickness of the equipment face. 2. Start the extrusion from point a to point b. Please see the figure in the left. 3. Click Finish Edit mode once done. 4. Do the same procedure to create the body of the FCU by setting the following: Extrusion end: 286mm Offset from the edge of the object : 62.5mm Once done, the object will be the same in the left figure. Page 12
13 5. Creating geometry for pipe connector. - On the Home Tab, click set to assign one of the sides of the object to be the reference workplane. (d) - On the Wok Plane dialog box, choose Pick the Workplane. - Pick the object s side surface. (e) - Go to the right elevation of the model using View Cube. This is to easily draw a circle that will represent the connection point. - Repeat no. 2 procedures to draw the pipe connection points, this time choose Circle for the drawing method. (f) - Make 12.5mm for the radius and 50mm for the extrusion end. - Add two more connection points for chilled water supply, chilled water return and drain system of the equipment. - The object will be the same as the figure below once done. Created Geometry Page 13
14 Other detail steps in creating 3D geometry can be found inside the Family Guide of Revit. Creating CP83 2D Symbol 2D symbol will be the representation of the 3D elements in plan view in compliance with the CP83 standards. Follow below procedures to add 2D symbols to the 3D object. 1. Use the symbolic lines under Annotate tab of Revit to draw the 2D symbol. 2. Trace some of the lines of the 3D geometry. Adding MEP Connectors Connectors allow Revit MEP content to participate in specific systems and facilitate calculations for a variety of parameters. Below connectors can be added to the 3D geometry as requires by the equipment to be created. Please do below procedures to add MEP connectors to the 3D model. 1. On the 3D view, choose Pipe connector from the Home Tab. Page 14
15 2. Pick the edge of the pipe connection points that has been modeled 3. Select the Pipe Connector Element and on Property Panel, change the System Type to Hydronic Supply (4) and the Radius of the pipe to 12.5mm. 4. Create 2 more connectors for hydronic return and drain by doing the above procedures. 5. Choose the Electrical Connectors to add the electrical properties of the equipment. This can be done by doing the above procedures. On the Property panel, key-in the desire voltage. Note: More steps for Adding Connectors Properties can be found on page 82 of the Revit Families Guide. Page 15
16 Managing object Visibility Graphics Visibility of a object determines in which view the object displays and what it looks like in that view. In a 3D or elevation view, you may want a fully detailed 3D representation of the element but only 2D symbols on your floor plans. You have the flexibility to display different levels of geometry by controlling the objects geometry visibility. 1. On the 3D view, select the elements that will not be shown on plan. Use the Ctl key on the keyboard to do a multiple selection if necessary. 2. Choose the Visibility Settings and uncheck the Plan / RCP in the setting. Testing the Object into the Project After you have finished the object, load it in at least one project, and create elements with the family types to ensure it works correctly. Make sure you select a test project that contains any geometry with which the family must interact. For example, if the family is a host-based family like a lighting fixture, ensure that the test project contains the host elements (ceilings or walls). BEST PRACTICE Until you successfully test the family, do not save it in a library where it is accessible to others. To test the Object into the project 1. Open a test project. NOTE Imperial and metric testing projects are available in the Training Files folder. Click Open Project, click Training Files in the left pane of the Open dialog, and open Imperial or Metric. Open Imperial_ Family_Testing_Template.rvt or Metric_Family_Testing_Template.rvt. 2. To load the family in the project, do either of the following: In the family, click Home tab Family Editor panel Load into Project. In the project, click Insert tab Load from Library panel Load Family, navigate to the location of the family, select it, and click Open. 3. In the project, click the Home tab, and then click the appropriate tool to begin creating an element from one of the new family types. 4. On the Properties panel, select a type from the Type Selector drop-down. Page 16
17 5. Add the element to the project. If the element is host-based, place it in a host element. 6. In the current view, test the element: - On the View Control Bar, change the Detail Level and/or Model Graphics style to ensure that visibility settings work correctly. - Click View tab Graphics panel Visibility & Graphics, and change the visibility for the element by category and, if applicable, by subcategories. - Select the element, right-click, and click Element Properties. - In the Instance Properties dialog, change any of the instance parameters, and click OK to view and verify the changes. - If the family contains multiple types, select the element, and on the Modify <element> tab Element panel, select a different family type from the Type Selector drop-down. 7. Open additional project views, and repeat step If the family contains more than one type, repeat steps 3-6 to test other types in the family. 9. If you find any errors in the family, edit the family, and retest it in a project. 10. When you finish testing the family, save it in the metric Revit MEP library or in another location of your choice. Page 17
18 4. References Revit Families Guide Hands on tutorial with training files included Library Creation Video Tutorials Start Creating Geometry Making Parametric Library Customizing Autodesk Seek Library to comply with the local standards Content Modification Page 18
Exercise 9-6 Creating a Window Family
Exercise 9-6 Creating a Window Family Estimated Time: File: 10 minutes ex8-5, generic model wall based.rft This exercise reinforces the following skills: Standard Component Families Templates We want to
More informationAll in the Family: Creating Parametric Components in Autodesk Revit
All in the Family: Creating Parametric Components in Autodesk Revit Matt Dillon D C CADD AB2100 The key to mastering Autodesk Revit Architecture, Autodesk Revit MEP, or Autodesk Revit Structure software
More informationThis Skill Builder demonstrates how to define and place sketched symbols in drawings.
Sketched Symbols This Skill Builder demonstrates how to define and place sketched symbols in drawings. A sketched symbol is a user-defined symbol. You create sketched symbols in the sketch environment
More informationIntroduction to Autodesk Inventor for F1 in Schools
Introduction to Autodesk Inventor for F1 in Schools F1 in Schools Race Car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s digital prototyping strategy
More informationIntroduction to Autodesk Inventor for F1 in Schools
F1 in Schools race car Introduction to Autodesk Inventor for F1 in Schools In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital Prototyping strategy
More informationTABLE OF CONTENTS. INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE...
Starting Guide TABLE OF CONTENTS INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE... 7 ADVANCE CONCRETE USER INTERFACE... 7 Other important
More informationChapter 1. Creating Sketches in. the Sketch Mode-I. Evaluation chapter. Logon to www.cadcim.com for more details. Learning Objectives
Chapter 1 Creating Sketches in Learning Objectives the Sketch Mode-I After completing this chapter you will be able to: Use various tools to create a geometry. Dimension a sketch. Apply constraints to
More informationAutodesk Fusion 360 Badge Guide: Design an F1 in Schools Trophy
Autodesk Fusion 360 Badge Guide: Design an F1 in Schools Trophy Abstract: Gain basic understanding of creating 3D models in Fusion 360 by designing an F1 in Schools trophy. This badge may be claimed by
More informationThe number of parameters required for authoring an ipart depends on the type of the part you are publishing.
Publishing and Styles In This Exercise This Skill Builder demonstrates how to create a tube and pipe ipart, publish it into a custom Tube & Pipe Library, create a style using published parts, and then
More informationCreating Steel Fabrication Friendly Families and Schedules with Autodesk Revit Structure
Creating Steel Fabrication Friendly Families and Schedules with Autodesk Revit Structure Tina Bos Herold Engineering Limited SE3048-L Once you have mastered the day-to-day use of Autodesk Revit Structure,
More informationATS Revit Family Creation Standards July 23 rd, 2012 Plumbing Fixtures: Faucets Version 1.0
This document outlines the design standard Allied Technical Services uses in the creation of Revit families. This edition will feature faucets, more specifically, bathroom and kitchen faucets. It is important
More informationSteady Flow: Laminar and Turbulent in an S-Bend
STAR-CCM+ User Guide 6663 Steady Flow: Laminar and Turbulent in an S-Bend This tutorial demonstrates the flow of an incompressible gas through an s-bend of constant diameter (2 cm), for both laminar and
More informationIntroduction to CATIA V5
Introduction to CATIA V5 Release 16 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com
More informationSession 25 Revit MEP Tips and Tricks
Session 25 Revit MEP Tips and Tricks Page 1 of 17 Sometimes it's the little things which make all the difference. I thought I would share some nifty tricks that can help make Revit MEP go down a little
More informationPro/ENGINEER Wildfire 4.0 Basic Design
Introduction Datum features are non-solid features used during the construction of other features. The most common datum features include planes, axes, coordinate systems, and curves. Datum features do
More informationMS WORD 2007 (PC) Macros and Track Changes Please note the latest Macintosh version of MS Word does not have Macros.
MS WORD 2007 (PC) Macros and Track Changes Please note the latest Macintosh version of MS Word does not have Macros. Record a macro 1. On the Developer tab, in the Code group, click Record Macro. 2. In
More informationCreating 2D Drawings from 3D AutoCAD Models
Creating 2D Drawings from 3D AutoCAD Models David Piggott CrWare, LP GD205-2P This class explores the various techniques in creating 2D part and assembly drawings from 3D AutoCAD models. As part of the
More informationBuilding Information Modeling with Autodesk Revit Building. Student Workbook
Building Information Modeling with Autodesk Revit Building Student Workbook Contents Introduction 4 Unit 1 7 Theory: CAD Versus BIM... 7 Autodesk Revit Building: Introduction, Interface, and Sketching...
More informationChapter 9. Editing Features. Learning Objectives
Chapter 9 Editing Features Learning Objectives After completing this chapter, you will be able to: Edit features. Edit sketches of the sketch based features. Edit the sketch plane of the sketch based features.
More informationVisual Tutorial Basic Edition 1. Visual. Basic Edition Tutorial. www.visuallightingsoftware.com
Visual Tutorial Basic Edition 1 Visual Basic Edition Tutorial www.visuallightingsoftware.com Visual Tutorial Basic Edition 2 Basic Edition Tutorial Introduction In this tutorial, you will use the Visual
More informationRaising the Roof Creating Roofs in Revit David Cohn
David Cohn AB322-1 Roofs are one of the most complex architectural elements to model, but with Revit you can create just about any type of roof. This class will explore the best methods for creating various
More informationMicrosoft Word 2011: Create a Table of Contents
Microsoft Word 2011: Create a Table of Contents Creating a Table of Contents for a document can be updated quickly any time you need to add or remove details for it will update page numbers for you. A
More informationME 24-688 Week 11 Introduction to Dynamic Simulation
The purpose of this introduction to dynamic simulation project is to explorer the dynamic simulation environment of Autodesk Inventor Professional. This environment allows you to perform rigid body dynamic
More informationLayout Tutorial. Getting Started
Getting Started Layout Tutorial This tutorial will explain how create a layout template, send views to a layout page, then save the document in PDF format. In this tutorial you will learn about: Creating
More informationPrepare your data in ArcGIS for Desktop
Collector for ArcGIS (ios) Tutorials Prepare your data in ArcGIS for Desktop Create and share a map for data collection Track where collectors went Additional help FAQs Supported data Configure map capabilities
More informationVico Office R3.0 Help
1 Vico Office R3.0 Help User guide 2 Contents 3 Vico Office R3.0 Help Revision 1 4 Vico Office Introduction Welcome to Vico Office, Vico's integrated Virtual Construction environment. The Vico Office Suite
More informationSpaceClaim Introduction Training Session. A SpaceClaim Support Document
SpaceClaim Introduction Training Session A SpaceClaim Support Document In this class we will walk through the basic tools used to create and modify models in SpaceClaim. Introduction We will focus on:
More informationFDOT Roadway Design and 3D Modeling
State of Florida Department of Transportation FDOT Roadway Design and 3D Modeling CE-11-0138, CE-11-0139, and CE-11-0140 User Training Manual October 30, 2014 ENGINEERING / CADD SYSTEMS OFFICE TALLAHASSEE,
More informationUnderstand the Sketcher workbench of CATIA V5.
Chapter 1 Drawing Sketches in Learning Objectives the Sketcher Workbench-I After completing this chapter you will be able to: Understand the Sketcher workbench of CATIA V5. Start a new file in the Part
More informationSolidWorks Tutorial 3 MAGNETIC BLOCK
SolidWorks Tutorial 3 MAGNETIC BLOCK Magnetic Block In this exercise you will make a magnetic block. To do so, you will create a few parts, which you will assemble. You will learn the following new applications
More informationLearning Autodesk. Modeling, Analysis and Animation SDC. Randy H. Shih. Better Textbooks. Lower Prices. PUBLICATIONS www.sdcpublications.
Learning Autodesk Inventor 2012 Modeling, Analysis and Animation Randy H. Shih SDC Better Textbooks. Lower Prices. PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Visit the following
More informationChapter 23: Drafting in Worksheet View
Chapter 23: Drafting in Worksheet View Worksheet View is a powerful, 2D production drafting module. Here you can find all of the drawing and editing tools needed to create fast, accurate, detailed working
More information511 - Creating Structural Frame Designs
4 th Generation VLC courtesy of Edison2 511 - Creating Structural Frame Designs Rahul Kulkarni, Manager, Product Design, Pune Center, Siemens PLM Software #SEU13 Agenda: 511 - Creating Structural Frame
More information84 part video tutorial training course. The course is 100% free with no catches or exclusions. You don
Please Note: If you're new to Revit, you may be interested in my " Beginner's Guide to Revit Architecture " 84 part video tutorial training course. The course is 100% free with no catches or exclusions.
More informationAutoCAD Civil 3D 2010 ESSENTIALS
AutoCAD Civil 3D 2010 ESSENTIALS SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. Visit our website to learn more about this and other books: AutoCAD Civil
More informationSearch help. More on Office.com: images templates
Page 1 of 7 PowerPoint 2010 Home > PowerPoint 2010 Help and How-to > Getting started with PowerPoint Search help More on Office.com: images templates Basic tasks in PowerPoint 2010 Here are some basic
More informationCATIA Functional Tolerancing & Annotation TABLE OF CONTENTS
TABLE OF CONTENTS Introduction...1 Functional Tolerancing and Annotation...2 Pull-down Menus...3 Insert...3 Functional Tolerancing and Annotation Workbench...4 Bottom Toolbar Changes...5 3D Grid Toolbar...5
More information11 Printing Designs. When you have completed this chapter, you will be able to:
11 Printing Designs Creating printed documents is the end we have worked towards from the beginning of this course. We have already been introduced to it very briefly with Printing - A First Look on page
More informationWeld Design. CATIA V5 Training Foils. Weld Design. Copyright DASSAULT SYSTEMES 1. Instructor Notes:
CATIA V5 Training Foils Weld Design Version 5 Release 19 January 2009 EDU_CAT_EN_WD1_FI_V5R19 1 About this course Objectives of the course Upon completion of this course you will be able to: - Weld parts,
More informationMulti-user Collaboration with Autodesk Revit Worksharing
AUTODESK REVIT WHITE PAPER Multi-user Collaboration with Autodesk Revit Worksharing Contents Contents... 1 Autodesk Revit Worksharing... 2 Starting Your First Multi-user Project... 2 Autodesk Revit Worksets...
More informationEffective Collaboration using Revit Structure and AutoCAD MEP
REVIT STRUCTURE Effective Collaboration using Revit Structure and AutoCAD MEP This white paper explains how structural engineers using Revit Structure software and mechanical/electrical/plumbing (MEP)
More informationAutodesk Revit Architecture 2013 Fundamentals
Autodesk Revit Architecture 2013 Fundamentals Supplemental Files SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial files on enclosed
More informationLayout Tutorial. Chapter 10: Getting Started
Chapter 10: Layout Tutorial In this tutorial we will create a layout template, send a few views to a layout page, then save this document in PDF format. In this tutorial you will learn about: Creating
More informationIntroduction to Measurement Tools
Introduction to Measurement Tools Revu's built-in measurement tools make it easy to take length, area, perimeter, diameter, volume and radius measurements, count from PDFs and perform area cutouts. Compatibility
More informationEffective Collaboration
AUTODESK BUILDING SOLUTIONS Effective Collaboration Exporting Revit Architecture Models as ACIS Solids for Use in AutoCAD MEP The intent of this paper is to explain a process by which architects using
More informationOrganizing and Managing Email
Organizing and Managing Email Outlook provides several tools for managing email, including folders, rules, and categories. You can use these tools to help organize your email. Using folders Folders can
More informationLinear Referencing Tutorial
Copyright 1995-2010 Esri All rights reserved. Table of Contents An overview of the linear referencing tutorial........................ 3 Exercise 1: Organizing your linear referencing data in ArcCatalog...............
More informationWIX: Building a Website with a Template. Choosing a Template First you will need to choose a template from the Create section of the Wix website.
WIX: Building a Website with a Template Choosing a Template First you will need to choose a template from the Create section of the Wix website. To choose a template: 1. Go to wix.com. 2. From the top
More informationCreating detailed drawings
Creating detailed drawings Publication Number spse01545 Creating detailed drawings Publication Number spse01545 Proprietary and restricted rights notice This software and related documentation are proprietary
More information3D Modeling in Vectorworks 2009 by Jonathan Pickup. mple
3D Modeling in Vectorworks 2009 by Jonathan Pickup mple 3D Modeling in Vectorworks 2009 by Jonathan Pickup 3D Modeling Vectorworks 2009 Published by Nemetschek North America 2008 Jonathan Pickup Vectorworks
More informationInterior Design Tutorial
Chapter 4: Interior Design Tutorial In the Interior Design Tutorial, we ll pick up where we left off in the House Design Tutorial. The shell and basic structure of our plan is complete, but a lot of interior
More informationRevit MEP. Autodesk Navisworks
What is BIM? Autodesk BIM is an intelligent model-based process that helps owners and service providers achieve business results by enabling more accurate, accessible, and actionable insight throughout
More informationBasic 2D Design Be sure you have the latest information!
Basic 2D Design mastercam x getting started tutorials Basic 2D Design December 2011 Be sure you have the latest information! Information might have been changed or added since this document was published.
More informationEnvisioneer Technical Note
Title Blocks By default there are four pre-defined Worksheet view windows available (Floor Plan, Elevations, Details, and Site Plan). Each one contains a generic border and title block supplied by Cadsoft.
More informationCreating Drawings in Pro/ENGINEER
6 Creating Drawings in Pro/ENGINEER This chapter shows you how to bring the cell phone models and the assembly you ve created into the Pro/ENGINEER Drawing mode to create a drawing. A mechanical drawing
More informationGenerative Drafting. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes
Generative Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Generative Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting
More informationSQL Server 2005: Report Builder
SQL Server 2005: Report Builder Table of Contents SQL Server 2005: Report Builder...3 Lab Setup...4 Exercise 1 Report Model Projects...5 Exercise 2 Create a Report using Report Builder...9 SQL Server 2005:
More informationThe Shorten AutoCAD the road solution for mechanical, electrical, to done. and plumbing engineering. AutoCAD AutoCAD.
The Shorten AutoCAD the road solution for mechanical, electrical, to done. and plumbing engineering. AutoCAD AutoCAD Civil 3D MEP 2009 More Productivity, Same Skills Michigan-based Peter Basso Associates
More informationCollaborating Across Disciplines with Revit Architecture, MEP, and Structure
Collaborating Across Disciplines with Revit Architecture, MEP, and Structure David Cohn AB104-3 Are you ready to take the next step and use building information modeling to share data across the entire
More informationEmail Basics. a. Click the arrow to the right of the Options button, and then click Bcc.
Email Basics Add CC or BCC You can display the Bcc box in all new messages that you compose. In a new message, do one of the following: 1. If Microsoft Word is your e-mail editor a. Click the arrow to
More informationInterior Design Tutorial
Chapter 4: Interior Design Tutorial In the Interior Design Tutorial, we ll pick up where we left off in the House Design Tutorial. The shell and basic structure of our plan is complete, but a lot of interior
More informationInstructions for Configuring a SAS Metadata Server for Use with JMP Clinical
Instructions for Configuring a SAS Metadata Server for Use with JMP Clinical These instructions describe the process for configuring a SAS Metadata server to work with JMP Clinical. Before You Configure
More informationMicrosoft Access 2010 Part 1: Introduction to Access
CALIFORNIA STATE UNIVERSITY, LOS ANGELES INFORMATION TECHNOLOGY SERVICES Microsoft Access 2010 Part 1: Introduction to Access Fall 2014, Version 1.2 Table of Contents Introduction...3 Starting Access...3
More informationKitchen and Bath Design Tutorial
Adding Cabinets Kitchen and Bath Design Tutorial This tutorial continues where the Interior Design Tutorial left off. You should save this tutorial using a new name to archive your previous work. The tools
More informationReal Time Rendering. Preface What's New Getting Started Basic Tasks Advanced Tasks Workbench Description Index
Real Time Rendering Preface What's New Getting Started Basic Tasks Advanced Tasks Workbench Description Index Dassault Systèmes 1994-99. All rights reserved. Preface CATIA Version 5 Real Time Rendering
More informationLearning Module 4 - Thermal Fluid Analysis Note: LM4 is still in progress. This version contains only 3 tutorials.
Learning Module 4 - Thermal Fluid Analysis Note: LM4 is still in progress. This version contains only 3 tutorials. Attachment C1. SolidWorks-Specific FEM Tutorial 1... 2 Attachment C2. SolidWorks-Specific
More informationKodu Curriculum: Getting Started with Keyboard and Mouse
Kodu Curriculum: Getting Started with Keyboard and Mouse PC Requirements 1. Kodu requires a Windows Operating System 2. DirectX9 graphics 3. Shader Model 2.0 or greater. How to Check Your DirectX Version
More informationApplying a circular load. Immediate and consolidation settlement. Deformed contours. Query points and query lines. Graph query.
Quick Start Tutorial 1-1 Quick Start Tutorial This quick start tutorial will cover some of the basic features of Settle3D. A circular load is applied to a single soil layer and settlements are examined.
More informationLayout Tutorial. Chapter 10: Getting Started
Chapter 10: Layout Tutorial In this tutorial we will create a layout template, send a few views to a layout page, then save this document in PDF format. In this tutorial you will learn about: Creating
More informationIn the Link Point Cloud window, locate the desired point cloud file
Point Clouds Adding a Point Cloud: Open a Plan, Elevation, Section, or 3D view Select the Insert tab o In the Link section, select the Point Cloud button In the Link Point Cloud window, locate the desired
More informationMET 306. Activity 8a. Mechanism Design Creo 2.0 Level 7 POINT A GROUND LINK LINK 1 LINK 2 LINK 3 POINT B 10/15/2010 1
Mechanism Design Creo 2.0 Level 7 POINT A LINK 1 GROUND LINK LINK 2 LINK 3 POINT B 10/15/2010 1 Download parts ground, key, link_1, link_2, link_3 and pulley from the V:/MET_306/Activity_8_Creo drive.
More informationInstructions to view & create.kmz/.kml files from Google Earth
Page 1 of 6 Instructions to view & create.kmz/.kml files from Google Earth Make sure you have Google Earth downloaded on your computer. If you don t, please visit this link to download Google Earth http://www.google.com/earth/download/ge.
More informationHow To Create A View Frame In 3D
12/4/2008-10:00 am - 11:30 am Room:Palazzo O-P (5th) The Secrets of Cutting Plan and Profile Sheets in AutoCAD Civil 3D Michelle Rasmussen - Application Engineer, IMAGINiT Technologies CV304-1P In this
More informationAuto-Archiving your Emails in Outlook
Changing the AutoArchive Settings for all your Mailbox Folders Changing the AutoArchive Settings for all your Mailbox Folders (cont.) One way to minimize the amount of server space you are using for your
More informationKitchen and Bath Design Tutorial
Adding Cabinets Chapter 5: Kitchen and Bath Design Tutorial This tutorial continues where the Materials Tutorial left off. You should save this tutorial using a new name to archive your previous work.
More informationLots and Lots of Symbols, Free. Introduction. Tutorial: Getting Symbols. New Commands in AutoCAD 2010: Part 8. by Ralph Grabowski
New Commands in AutoCAD 2010: Part 8 Lots and Lots of Symbols, Free by Ralph Grabowski Introduction AutoCAD 2010 introduces a new way to access symbols from Autodesk's Web site -- and a way to share yours
More informationSetting Up a New Project
Setting Up a New Project Contents About this tutorial... 3 Step 1. Create a new project... 3 Step 2. Select project settings... 4 Step 3. Save your project... 11 Step 4. Create a project template... 12
More informationLayouts, Plotting, Printing
Layouts, Plotting, Printing Sacramento City College Engineering Design Technology Layouts, Plotting, Printing 1 Objectives Print and plot a drawing. Set up layouts using title blocks and viewports. Create
More informationAECOsim Building Designer. Quick Start Guide. Chapter 15 Creating Construction Documents. 2012 Bentley Systems, Incorporated. www.bentley.
AECOsim Building Designer Quick Start Guide Chapter 15 Creating Construction Documents 2012 Bentley Systems, Incorporated www.bentley.com/aecosim Table of Contents Creating Construction Documents... 3
More informationTic, Tie & Calculate Quick Start Guide. Quick Start Guide
Quick Start Guide 1 Table of Contents Quick Start Guide... 3 Welcome to Tic, Tie & Calculate... 3 Features Overview... 3 Important Installation Notes... 3 Installation... 4 Step 1: Receive Account Creation
More informationSolidWorks: Mirror, Revolve, and. Introduction to Robotics
SolidWorks: Mirror, Revolve, and Circular Pattern Introduction to Robotics Let s Review At this point we have learned the following: Extrude Boss/Base Extruded Cut Adding Relations and Dimensions Linear
More informationPresentations and PowerPoint
V-1.1 PART V Presentations and PowerPoint V-1.2 Computer Fundamentals V-1.3 LESSON 1 Creating a Presentation After completing this lesson, you will be able to: Start Microsoft PowerPoint. Explore the PowerPoint
More informationUsing Parametric Equations in SolidWorks, Example 1
Using Parametric Equations in SolidWorks, Example 1 (Draft 4, 10/25/2006, SW 2006) Introduction In this example the goal is to place a solid roller on a solid wedge. Their relationship will be governed
More informationJumpStart Guide. Trimble QuickPen PipeDesigner 3D Software
L JumpStart Guide Trimble QuickPen PipeDesigner 3D Software Revision A February 2013 F Englewood Office Trimble Navigation Limited 384 Inverness Parkway, Suite 200 Englewood, Colorado 80112 (800) 234-3758
More informationAutodesk Revit Architecture 2011 Professional Massmodeling Rendering Video Tutorial
Autodesk Revit Architecture 2011 Professional Massmodeling Rendering Video Tutorial Instructor Handout Created by: Marvi Basha, Klaus Hyden und Philipp Müller Autodesk Student Experts TU Graz September
More informationSmart Board Notebook Software A guide for new Smart Board users
Smart Board Notebook Software A guide for new Smart Board users This guide will address the following tasks in Notebook: 1. Adding shapes, text, and pictures. 2. Searching the Gallery. 3. Arranging objects
More informationguide Axis Camera Families for Autodesk Revit
guide Axis Camera Families for Autodesk Revit Interactive 3D CAD security camera models Table of contents 1. Introduction 3 2. Loading Axis Camera Families 3 3. Using the camera families 4 3.1 Mounting
More informationCommunicate: In Print
Communicate: In Print A simple guide Work areas Communicate: In Print has two different modes in which to edit your documents: Create and Adjust modes. These are easily interchangeable and the toolbars
More informationThere are two distinct working environments, or spaces, in which you can create objects in a drawing.
That CAD Girl J ennifer dib ona Website: www.thatcadgirl.com Email: thatcadgirl@aol.com Phone: (919) 417-8351 Fax: (919) 573-0351 Autocad Model Space and Paper Space Model Space vs. Paper Space Initial
More informationDatum > Curve KIM,ME,NIU
Datum > Curve Intersect First create at least one quilt on the surface of the model. Feature > Surface (> New) > Copy (do not use offset that creates a surface off the solid surface even with zero offset)
More informationEDIT202 PowerPoint Lab Assignment Guidelines
EDIT202 PowerPoint Lab Assignment Guidelines 1. Create a folder named LABSEC-CCID-PowerPoint. 2. Download the PowerPoint-Sample.avi video file from the course WebCT/Moodle site and save it into your newly
More informationAn introduction to 3D draughting & solid modelling using AutoCAD
An introduction to 3D draughting & solid modelling using AutoCAD Faculty of Technology University of Plymouth Drake Circus Plymouth PL4 8AA These notes are to be used in conjunction with the AutoCAD software
More informationAutoCAD Structural Detailing 2011. Getting Started with AutoCAD Structural Detailing, Reinforcement module
AutoCAD Structural Detailing 2011 Getting Started with AutoCAD Structural Detailing, Reinforcement module 2010 Autodesk, Inc. All Rights Reserved. Except as otherwise permitted by Autodesk, Inc., this
More informationPublishing Geoprocessing Services Tutorial
Publishing Geoprocessing Services Tutorial Copyright 1995-2010 Esri All rights reserved. Table of Contents Tutorial: Publishing a geoprocessing service........................ 3 Copyright 1995-2010 ESRI,
More informationTutorial: 3D Pipe Junction Using Hexa Meshing
Tutorial: 3D Pipe Junction Using Hexa Meshing Introduction In this tutorial, you will generate a mesh for a three-dimensional pipe junction. After checking the quality of the first mesh, you will create
More informationMicrosoft Word 2010. Quick Reference Guide. Union Institute & University
Microsoft Word 2010 Quick Reference Guide Union Institute & University Contents Using Word Help (F1)... 4 Window Contents:... 4 File tab... 4 Quick Access Toolbar... 5 Backstage View... 5 The Ribbon...
More informationStructure Design. Preface What's New? Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index
Structure Design Preface What's New? Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index Dassault Systèmes 1994-2000. All rights reserved. Preface CATIA Version
More informationSolidWorks. SolidWorks Teacher Guide. and Student Courseware
SolidWorks SolidWorks Teacher Guide and Student Courseware SolidWorks Corporation Outside the U.S.: +1-978-371-5011 300 Baker Avenue Fax: +1-978-371-7303 Concord, Massachusetts 01742 USA Email: info@solidworks.com
More informationFiles Used in this Tutorial
Generate Point Clouds Tutorial This tutorial shows how to generate point clouds from IKONOS satellite stereo imagery. You will view the point clouds in the ENVI LiDAR Viewer. The estimated time to complete
More information