1.47 N {150 gf} D2S-10 D2S-5 D2S N {50 gf} - D2S-5-F D2S-01-F

Transcription

1 ubminiature Basic witch ubminiature witch with uperb Flux Resistance One-piece terminal construction to keep out flux. High operating-position accuracy (± mm) enables easy peripheral design and positioning. Use of pin plunger also allows horizontal operation. RoH Compliant Number Legend Ratings 10 : 50 VC : 15 VC 5 01 : 30 VC 0.1. ctuator None : Pin plunger L : Hinge lever L13 : imulated roller lever L : Hinge roller lever List of s 3. Maximum Force (OF) None : 1.47 N {150 gf} -F : (For 0.1, 5 ) Note: The given values are for pin plunger only. 4. Terminals None : older : elf-clinching PCB Ratings ctuator Terminals OF max Pin plunger older 1.47 N {150 gf} F -01-F elf-clinching PCB 1.47 N {150 gf} F -01-F Hinge lever imulated roller lever Hinge roller lever older elf-clinching PCB older elf-clinching PCB older elf-clinching PCB -10L -5L -01L - -5L-F -01L-F -10L -5L -01L - -5L-F -01L-F -10L13-5L13-01L L13-F -01L13-F -10L13-5L13-01L L13-F -01L13-F -10L -5L -01L - -5L-F -01L-F -10L -5L -01L - -5L-F -01L-F eparator (old eparately), Terminal Connector (old eparately) Refer to "Basic witch Common ccessories" 1

2 ubminiature Basic witch Contact Form PT COM NO NC Contact pecifications Item pecification Rivet Crossbar Contact Material ilver alloy Gold alloy Gap (standard value) mm Inrush NC 0 max. 1 max. current NO 15 max. 10 max. 1 max. Minimum applicable load (reference value) * 5 VC 160 m 5 VC 1 m * Please refer to "Using Micro Loads" of " Precautions" for more information on the minimum applicable load. Ratings Characteristics Note. The above rating values apply under the following test conditions. (1) mbient temperature: 0± C () mbient humidity: 65±5% (3) frequency: 30 operations/min pproved afety tandards The items shown in the "List of s" are not standard approved. Consult your OMRON sales representative for specific with standard approvals. UL (UL1054)/C(C C. No.55) Rated voltage 15 VC 50 V Item Rated voltage Resistive load 50 VC VC 50 VC VC VC VC Item Permissible operating speed 0.1 mm to 1 m/s (for pin plunger ) Permissible Mechanical 400 operations/min operating frequency Electrical 60 operations/min Insulation resistance 100 MΩ min. (at 500 VC with insulation tester) Contact resistance OF 1.47 N 30mΩ max. 50 mω max. (initial value) OF 0.49 N - 50 mω max. 100 mω max. Between of the same polarity 1,000 VC 50/60 Hz 1 min ielectric strength * 1 Vibration resistance * hock resistance urability * 3 egree of protection Between current-carrying metal parts and ground Between each and non-current-carrying metal parts Malfunction urability Malfunction * Mechanical Electrical mbient operating temperature mbient operating humidity Weight OF 1.47 N OF 0.49 N OF 1.47 N OF ,500 VC 50/60 Hz 1 min 1,500 VC 50/60 Hz 1 min 10 to 55 Hz, 1.5 mm double amplitude 10,000,000 operations min. (60 operations/min) 50,000 operations min. (30 operations/min) 1,000 m/s {approx. 100G} max. 500 m/s {approx. 50G} max. 300 m/s {approx. 30G} max. 00 m/s {approx. 0G} max. 30,000,000 operations min. (60 operations/min) 00,000 operations min. (30 operations/min) IEC IP40-5 C to +85 C (at ambient humidity of 60% max.) (with no icing or condensation) 85% max. (for +5 C to +35 C) pprox. 1.6 g (pin plunger ) Note. The data given above are initial values. *1. The values for dielectric strength shown are for with a eparator (refer to "Micro witch Common ccessories"). *. The values are at Free Position and Total Travel Position values for pin plunger, and Total Travel Position value for lever. Close or open circuit of the contact is 1ms max. *3. For testing conditions, consult your OMRON sales representative.

3 Terminals/ppearances (Unit: mm) ubminiature Basic witch Mounting Holes (Unit: mm) older elf-clinching PCB -.4 dia. mounting holes or M.3 screw holes dia.holes ± ±0. 6.4± ± ±0. 6.4±0. <PCB Mounting imensions (Reference)> dia. 8.8± ±0. PCB's thickness t 1.6mm imensions (Unit: mm) and Characteristics The following figures show with self-clinching PCB. For the solder, refer to "Terminals/ppearances". is replaced with the code for the terminal that you need. ee the "List of s" for available combinations of. Pin plunger -10@ -5@ -5-F@ -01@ -01-F@ ± ±0.05 dia..5±0.07 dia. 16.1± ±0. PT ±0.05 dia. 6.4±0. Force OF Max. Pretravel PT Max. Overtravel OT Min. Movement ifferential M Max. -10@ -5@ -01@ 1.47 N {150 gf} N {5 gf} 0.7 mm 0.4 mm 0.1 mm Position OP 8.4± mm -5-F@ -01-F@ 0.04 N {4 gf} Hinge lever -10L@ -5L@ -5L-F@ -01L@ -01L-F@ t 0.3 *.35±0.05 dia ±0.07 dia. 16.1± ±0..35±0.05 dia. * tainless-steel lever ±0. Force OF Max. Overtravel OT Min. Movement ifferential M Max. Free Position Max. Position OP -10L@ -5L@ -01L@ 13.6 mm 9.4±0.8mm -5L-F@ -01L-F@ 0.0 N { gf} imulated roller lever -10L13@ -5L13@ -5L13-F@ -01L13@ -01L13-F@ t 0.3 *.35±0.05 dia ±0.07 dia. 16.1± ±0. R.35±0.05 dia. *tainless-steel lever ±0. Force OF Max. Overtravel OT Min. Movement ifferential M Max. Free Position Max. Position OP -10L13@ -5L13@ -01L13@ -5L13-F@ -01L13-F@ 15.5 mm 11.4± 0.0 N { gf} Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note. The operating are for operation in the direction ( ). 3

4 ubminiature Basic witch Hinge roller lever t=0.3 *1.35±0.05 dia ±0.07 dia. 16.1± ±0..35±0.05 dia OP *1. tainless-steel lever *. Polyacetal resin roller 4.8x3. * dia. 6.4±0. Force OF Max. Overtravel OT Min. Movement ifferential M Max. Free Position Max. Position OP -10L@ -5L@ -01L@ 19.3 mm 15.1± -5L-F@ -01L-F@ 0.0 N { gf} Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note. The operating are for operation in the direction ( ). Precautions Please refer to "Basic witches Common Precautions" for correct use. Cautions oldering When using automatic soldering baths, we recommend soldering at 60±5 C within 5 seconds. Make sure that the liquid surface of the solder does not flow over the edge of the board. When soldering manually, complete the soldering at the iron tip temperature between 350 to 400 C within 3 seconds, and do not apply any external force for 1 minute after soldering. When applying solder, keep the solder away from the case of the witch and do not allow solder or flux to flow into the case. Correct Use Mounting Use M.3 mounting screw with plane washers or spring washers to securely mount the witch. Tighten the screws to a torque of 0.3 to 0.6 N m {.3 to.7 kgf cm}. Using Micro Loads Using a model for ordinary loads to open or close the contact of a micro load circuit may result in faulty contact. Use that operate in the following range. However, even when using micro load within the following operating range, if inrush current occurs when the contact is opened or closed, it may increase the contact wear and so decrease durability. Therefore, insert a contact protection circuit where necessary. The N-level reference value applies for the minimum applicable load. This value indicates the malfunction reference level for the reliability level of 60% (λ60). (JI C5003) The equation, λ60= 10-6 /operations indicates that the 1 estimated malfunction rate is less than,000,000 operations with a reliability level of 60%. Voltage (V) 0.16 m 30 6 m 100 m 4 1 Micro load type range -01 Normal load type range m 100 m 160 m ,000 Current (m) 4

5 ubminiature Basic witch pplication examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: o not use this document to operate the Unit. OMRON Corporation ELECTRONIC N MECHNICL COMPONENT COMPNY Contact: Cat. No. B09-E (007)(O) 5