Introduction Process Piping and Instrumentation Diagram (P&ID)

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Introduction Process Piping and Instrumentation Diagram (P&ID)"

Transcription

1 Session 2313 Use of Lab Experiments to Build Transport Concepts Abstract

2 Introduction Process Piping and Instrumentation Diagram (P&ID)

3 Viscosity Measurement

4

5 Absolute Viscosity vs. Sucrose Conce 40C Absolute Viscosity (cp) Sucrose Concentration (%) Differential Pressure Measurement

6 Pressure v. DP Cell Readings Differential Pressure (psia) DP Transmitter Reading (ma) Fluid Velocity and Reynolds Number

7 Flow Rate vs. Rotameter Reading Flow Rate (gpm) Rotameter Reading (% flow) Frictional Losses

8 ( ) + = 㰗呇 Friction Losses vs. Flow Rate Frictional Loss (J/kg) Flow Rate (gpm ) Pumping System Analysis

9 = + 㰗呇 π + + Σ + + Σ

10 Suction Line Discharge Line No. k Total No. k Total 1/2" Pipe Straight Pipe Ball Valve 3-way Valve Control Valve 90 o Elbow Tee (along run) Tee (as elbow) Expansion Contraction Coupling Pressure Tap Rotameter Orifice Plate 1" Pipe Straight Pipe 90 o Elbow Coupling Pressure Tap Contraction ΣK

11 Pumping System Curve Total Head Loss (ft) Volumetric Flow Rate (gpm) Discussion

12 Conclusion References

13 Acknowledgement Authors Anna Siemionko Nam K. Kim

Michael Montgomery Marketing Product Manager Rosemount Inc. Russ Evans Manager of Engineering and Design Rosemount Inc.

Michael Montgomery Marketing Product Manager Rosemount Inc. Russ Evans Manager of Engineering and Design Rosemount Inc. ASGMT / Averaging Pitot Tube Flow Measurement Michael Montgomery Marketing Product Manager Rosemount Inc. Russ Evans Manager of Engineering and Design Rosemount Inc. Averaging Pitot Tube Meters Introduction

More information

FLUID FLOW Introduction General Description

FLUID FLOW Introduction General Description FLUID FLOW Introduction Fluid flow is an important part of many processes, including transporting materials from one point to another, mixing of materials, and chemical reactions. In this experiment, you

More information

Advanced Differential Pressure Flowmeter Technology V-CONE FLOW METER TECHNICAL BRIEF

Advanced Differential Pressure Flowmeter Technology V-CONE FLOW METER TECHNICAL BRIEF Advanced Differential Pressure Flowmeter Technology V-CONE FLOW METER TECHNICAL BRIEF Table of Contents Section 1 - General Introduction 1.1 1 Principles Of Operation 1.2 1 Reshaping The Velocity Profile

More information

Testing Protocol for Differential Pressure Measurement Devices API MPMS Chapter 22.2

Testing Protocol for Differential Pressure Measurement Devices API MPMS Chapter 22.2 Testing Protocol for Differential Pressure Measurement Devices API MPMS Chapter 22.2 Steve Baldwin Chevron Energy Technology Company Houston, Texas USA Casey Hodges CEESI Measurement Solutions. Nunn, Colorado

More information

WATER MEASUREMENT USING TWO INCH (50 mm) DRAIN TESTS

WATER MEASUREMENT USING TWO INCH (50 mm) DRAIN TESTS GAP.14.1.2.2 A Publication of Global Asset Protection Services LLC WATER MEASUREMENT USING TWO INCH (50 mm) DRAIN TESTS INTRODUCTION A hydrant or other large-volume flow test is necessary for proper water

More information

ME 305 Fluid Mechanics I. Part 8 Viscous Flow in Pipes and Ducts

ME 305 Fluid Mechanics I. Part 8 Viscous Flow in Pipes and Ducts ME 305 Fluid Mechanics I Part 8 Viscous Flow in Pipes and Ducts These presentations are prepared by Dr. Cüneyt Sert Mechanical Engineering Department Middle East Technical University Ankara, Turkey csert@metu.edu.tr

More information

Pressure drop in pipes...

Pressure drop in pipes... Pressure drop in pipes... PRESSURE DROP CALCULATIONS Pressure drop or head loss, occurs in all piping systems because of elevation changes, turbulence caused by abrupt changes in direction, and friction

More information

Experiment # 3: Pipe Flow

Experiment # 3: Pipe Flow ME 05 Mechanical Engineering Lab Page ME 05 Mechanical Engineering Laboratory Spring Quarter 00 Experiment # 3: Pipe Flow Objectives: a) Calibrate a pressure transducer and two different flowmeters (paddlewheel

More information

CHE 253M Experiment No. 3 LIQUID FLOW MEASUREMENT

CHE 253M Experiment No. 3 LIQUID FLOW MEASUREMENT Rev 8/15 AW/GW CHE 253M Experiment No. 3 LIQUID FLOW MEASUREMENT The objective of this experiment is to familiarize the student with several types of flow-measuring devices commonly used in the laboratory

More information

Applied Fluid Mechanics

Applied Fluid Mechanics Applied Fluid Mechanics 1. The Nature of Fluid and the Study of Fluid Mechanics 2. Viscosity of Fluid 3. Pressure Measurement 4. Forces Due to Static Fluid 5. Buoyancy and Stability 6. Flow of Fluid and

More information

OAWWA 2013 Large Meter Testing: Analysis and Calibration

OAWWA 2013 Large Meter Testing: Analysis and Calibration OAWWA 2013 Large Meter Testing: Analysis and Calibration Aaron M. Horbovetz PMP, EIT Project Engineer How much water are you really putting into the distribution system? INFLOW = METERED OUT + LEAKAGE

More information

Experiment 3 Pipe Friction

Experiment 3 Pipe Friction EML 316L Experiment 3 Pipe Friction Laboratory Manual Mechanical and Materials Engineering Department College of Engineering FLORIDA INTERNATIONAL UNIVERSITY Nomenclature Symbol Description Unit A cross-sectional

More information

CHME 302 CHEMICAL ENGINEERING LABOATORY-I EXPERIMENT 302-1 FLOW MEASUREMENT TEST

CHME 302 CHEMICAL ENGINEERING LABOATORY-I EXPERIMENT 302-1 FLOW MEASUREMENT TEST CHME 302 CHEMICAL ENGINEERING LABOATORY-I EXPERIMENT 302-1 FLOW MEASUREMENT TEST OBJECTIVE The purpose of the experiment is to demonstrate the working principles of four most common devices used to measure

More information

Pacific Pump and Power

Pacific Pump and Power Pacific Pump and Power 91-503 Nukuawa Street Kapolei, Hawaii 96707 Phone: (808) 672-8198 or (800) 975-5112 Fax: (866) 424-0953 Email: sales@pacificpumpandpower.com Web: www.pacificpumpandpower.com Pumps

More information

TOPIC: 191004 KNOWLEDGE: K1.01 [3.3/3.5] Which one of the following contains indications of cavitation in an operating centrifugal pump?

TOPIC: 191004 KNOWLEDGE: K1.01 [3.3/3.5] Which one of the following contains indications of cavitation in an operating centrifugal pump? KNOWLEDGE: K1.01 [3.3/3.5] P21 Which one of the following contains indications of cavitation in an operating centrifugal pump? A. Low flow rate with low discharge pressure. B. Low flow rate with high discharge

More information

PROCESS CONTROL INDUSTRIAL MAINTENANCE TECHNICIAN CERTIFICATE

PROCESS CONTROL INDUSTRIAL MAINTENANCE TECHNICIAN CERTIFICATE PROCESS CONTROL INDUSTRIAL MAINTENANCE TECHNICIAN CERTIFICATE Process Control (T5552) Course 1 Introduction to Process Control Course 2 Instrument Tags Course 3 Piping and Instrumentation Diagrams Course

More information

2 1/2 Pipe. 40 = height. the gauge pressure inside the vessel from the gauge pressure at the nozzle inlet as shown:

2 1/2 Pipe. 40 = height. the gauge pressure inside the vessel from the gauge pressure at the nozzle inlet as shown: 116eering. Engineering. Engineering. Engineering. Engineerin Engineering Information SPECIFYING SPRAY NOZZLES Spray nozzles have three basic functions: meter flow distribute liquid break up a liquid stream

More information

ENERGY TRANSFER SYSTEMS AND THEIR DYNAMIC ANALYSIS

ENERGY TRANSFER SYSTEMS AND THEIR DYNAMIC ANALYSIS ENERGY TRANSFER SYSTEMS AND THEIR DYNAMIC ANALYSIS Many mechanical energy systems are devoted to transfer of energy between two points: the source or prime mover (input) and the load (output). For chemical

More information

Practice Problems on Pumps. Answer(s): Q 2 = 1850 gpm H 2 = 41.7 ft W = 24.1 hp. C. Wassgren, Purdue University Page 1 of 16 Last Updated: 2010 Oct 29

Practice Problems on Pumps. Answer(s): Q 2 = 1850 gpm H 2 = 41.7 ft W = 24.1 hp. C. Wassgren, Purdue University Page 1 of 16 Last Updated: 2010 Oct 29 _02 A centrifugal with a 12 in. diameter impeller requires a power input of 60 hp when the flowrate is 3200 gpm against a 60 ft head. The impeller is changed to one with a 10 in. diameter. Determine the

More information

Energy and Flow Measurement for Hydronic Systems

Energy and Flow Measurement for Hydronic Systems Energy and Flow Measurement for Hydronic Systems Presented By: George Szyszko Applications Consultant MCR for ONICON Incorporated Why Measure Thermal Energy? To control something, you must first measure

More information

pumping liquids JET PUMP TECHNICAL DATA

pumping liquids JET PUMP TECHNICAL DATA Section 000 Bulletin 00 Issued 5/87 Replaces /8 JET PUMP TECHNICAL DATA pumping liquids This technical bulletin includes general information about Penberthy Jet Pumps plus specific details for selecting

More information

Technical Publication

Technical Publication Technical Publication Flow Meter Selection for Improved Gas Flow Measurements: Comparison of Differential Pressure and Thermal Dispersion Technologies Art Womack, Sr. Applications Engineer Fluid Components

More information

Variable Frequency Drives for Water/Wastewater. Discussion on Pump Optimization Principles and Need to Know Drive Technology

Variable Frequency Drives for Water/Wastewater. Discussion on Pump Optimization Principles and Need to Know Drive Technology Variable Frequency Drives for Water/Wastewater Discussion on Pump Optimization Principles and Need to Know Drive Technology Pumps in Water Wastewater 2 WWW Challenges: Drivers/Trends Demand for WWW Age

More information

Pressure Drop Basics & Valve Sizing

Pressure Drop Basics & Valve Sizing Pressure Drop Basics & Valve Sizing What is Pressure Drop? The difference in pressure between two points in a system, caused by resistance to flow. What Pressure Drop is Not? Pressure drop is pressure

More information

PIPING WORKBOOK. Solving Piping and Header Networks Using CHEMCAD. Version 6.2

PIPING WORKBOOK. Solving Piping and Header Networks Using CHEMCAD. Version 6.2 PIPING WORKBOOK Solving Piping and Header Networks Using CHEMCAD Engineering advanced Version 6. Piping Simulation Methods Sizing Piping Components Pump Performance Curves Piping Networks Relief Header

More information

FLUID MECHANICS IM0235 DIFFERENTIAL EQUATIONS - CB0235 2014_1

FLUID MECHANICS IM0235 DIFFERENTIAL EQUATIONS - CB0235 2014_1 COURSE CODE INTENSITY PRE-REQUISITE CO-REQUISITE CREDITS ACTUALIZATION DATE FLUID MECHANICS IM0235 3 LECTURE HOURS PER WEEK 48 HOURS CLASSROOM ON 16 WEEKS, 32 HOURS LABORATORY, 112 HOURS OF INDEPENDENT

More information

Pipe Flow-Friction Factor Calculations with Excel

Pipe Flow-Friction Factor Calculations with Excel Pipe Flow-Friction Factor Calculations with Excel Course No: C03-022 Credit: 3 PDH Harlan H. Bengtson, PhD, P.E. Continuing Education and Development, Inc. 9 Greyridge Farm Court Stony Point, NY 10980

More information

Head Loss in Pipe Flow ME 123: Mechanical Engineering Laboratory II: Fluids

Head Loss in Pipe Flow ME 123: Mechanical Engineering Laboratory II: Fluids Head Loss in Pipe Flow ME 123: Mechanical Engineering Laboratory II: Fluids Dr. J. M. Meyers Dr. D. G. Fletcher Dr. Y. Dubief 1. Introduction Last lab you investigated flow loss in a pipe due to the roughness

More information

Flow Measurement Options for Pipeline and Open Channel Flow

Flow Measurement Options for Pipeline and Open Channel Flow Flow Measurement Options for Pipeline and Open Channel Flow October 2013 Presented by Molly Skorpik - 2013 Montana Association of Dam and Canal Systems Conference Irrigation Training and Research Center

More information

Thermal Dispersion Mass Flow

Thermal Dispersion Mass Flow Thermatel Thermal Dispersion Mass Flow Measurement Handbook Table of Contents Introduction...1 What is Mass Flow Measurement?...1 Types of Flow Transmitters...4 Differential Pressure...4 Orifice...4 Venturi...6

More information

BLOWERS EXHAUSTERS CONTINENTAL INDUSTRIE ASME PTC 10 PERFORMANCE TEST PROCEDURE. Blowers & Exhausters. Page 1 of 6 PURPOSE STANDARDS INSTRUMENTS

BLOWERS EXHAUSTERS CONTINENTAL INDUSTRIE ASME PTC 10 PERFORMANCE TEST PROCEDURE. Blowers & Exhausters. Page 1 of 6 PURPOSE STANDARDS INSTRUMENTS PURPOSE Page 1 of 6 Test purpose is the measure of the following compressor operating parameters: flow of gas handled pressure rice produced shaft power requirement efficiency surge limit STANDARDS Test

More information

A Spreadsheet Program for the Calculation of Piping Systems and the Selection of Pumps

A Spreadsheet Program for the Calculation of Piping Systems and the Selection of Pumps Session 1633 A Spreadsheet Program for the Calculation of Piping Systems and the Selection of Pumps Craig W. Somerton Department of Mechanical Engineering, Michigan State University I. Introduction An

More information

CENTRIFUGAL PUMP OVERVIEW Presented by Matt Prosoli Of Pumps Plus Inc.

CENTRIFUGAL PUMP OVERVIEW Presented by Matt Prosoli Of Pumps Plus Inc. CENTRIFUGAL PUMP OVERVIEW Presented by Matt Prosoli Of Pumps Plus Inc. 1 Centrifugal Pump- Definition Centrifugal Pump can be defined as a mechanical device used to transfer liquid of various types. As

More information

AKRON EDUCTORS TROUBLESHOOTING GUIDE OPERATION & THEORY OF EDUCTORS GENERAL OPERATING AND MAINTENANCE INSTRUCTIONS

AKRON EDUCTORS TROUBLESHOOTING GUIDE OPERATION & THEORY OF EDUCTORS GENERAL OPERATING AND MAINTENANCE INSTRUCTIONS AKRON EDUCTORS TROUBLESHOOTING GUIDE OPERATION & THEORY OF EDUCTORS GENERAL OPERATING AND MAINTENANCE INSTRUCTIONS Products Include: 60 gpm eductors Style 3060, 3061, 3062 & 3070 95 gpm eductors Style

More information

Energy Systems Engineering Technology

Energy Systems Engineering Technology College of Technology Instrumentation and Control Module # 4 Flow Measurement Document Intent: The intent of this document is to provide an example of how a subject matter expert might teach Flow Measurement.

More information

Methodology for Liquid Ultrasonic Flow Measurement within the Laminar to Turbulent Transitional Zone

Methodology for Liquid Ultrasonic Flow Measurement within the Laminar to Turbulent Transitional Zone Methodology for Liquid Ultrasonic Flow Measurement within the Laminar to Turbulent Transitional Zone Dave Seiler Daniel Measurement and Control March 25, 2014 Heavy Oil Definition!!!!the API classifies

More information

C. starting positive displacement pumps with the discharge valve closed.

C. starting positive displacement pumps with the discharge valve closed. KNOWLEDGE: K1.04 [3.4/3.6] P78 The possibility of water hammer in a liquid system is minimized by... A. maintaining temperature above the saturation temperature. B. starting centrifugal pumps with the

More information

Flow Measurement in Pipes and Ducts. Flow Measurement in Pipes and Ducts, Course #503. Presented by:

Flow Measurement in Pipes and Ducts. Flow Measurement in Pipes and Ducts, Course #503. Presented by: Flow Measurement in Pipes and Ducts, Course #503 Presented by: PDH Enterprises, LLC PO Box 942 Morrisville, NC 27560 www.pdhsite.com This course is about measurement of the flow rate of a fluid flowing

More information

Theory, Application, and Sizing of Air Valves

Theory, Application, and Sizing of Air Valves Theory, Application, and Sizing of Air Valves VAL-MATIC VALVE AND MANUFACTURING CORP. 905 RIVERSIDE DRIVE, ELMHURST, IL 60126 TEL. (630) 941-7600 FAX. (630) 941-8042 www.valmatic.com 1 THEORY, APPLICATION,

More information

Pipe Loss Experimental Apparatus

Pipe Loss Experimental Apparatus Pipe Loss Experimental Apparatus Kathleen Lifer, Ryan Oberst, Benjamin Wibberley Ohio Northern University Ada, OH 45810 Email: b-wibberley@onu.edu Abstract The objective of this project was to develop

More information

FIGURE P8 50E FIGURE P8 62. Minor Losses

FIGURE P8 50E FIGURE P8 62. Minor Losses 8 48 Glycerin at 40 C with r 1252 kg/m 3 and m 0.27 kg/m s is flowing through a 4-cm-diameter horizontal smooth pipe with an average velocity of 3.5 m/s. Determine the pressure drop per 10 m of the pipe.

More information

Method to Determine PERFORMANCE OF INDIRECT-FIRED WATER HEATERS March 2003 Edition

Method to Determine PERFORMANCE OF INDIRECT-FIRED WATER HEATERS March 2003 Edition Supplement to TESTING STANDARD Method to Determine PERFORMANCE OF INDIRECT-FIRED WATER HEATERS March 2003 Edition [NOTE: This supplement incorporates testing and calculations to determine heat source friction

More information

! WARNING. Before using product, read and understand instructions.

! WARNING. Before using product, read and understand instructions. McDonnell & Miller Installation & Maintenance Instructions MM-600G) Series FS8-W General Purpose Liquid Flow Switch OPERATION This control is an independently mounted water flow sensing device that makes

More information

Energy Efficiency Considerations in Pumps and Pump Stations

Energy Efficiency Considerations in Pumps and Pump Stations Energy Efficiency Considerations in Pumps and Pump Stations Jeff Foray, P.E. (JeffForay@KennedyJenks.com) WSU Extension Energy Program 14 March 2014 How Do You Save Energy? Don t design it wrong Operate

More information

ABB Flowmeters Review of industrial processing flowmeters

ABB Flowmeters Review of industrial processing flowmeters White paper ABB Flowmeters Review of industrial processing flowmeters Understanding flowmeters and their pros and cons By Ron DiGiacomo, ABB Measurement Products One of the most critical measurements in

More information

Sta-Rite Industries Basic Training Manual

Sta-Rite Industries Basic Training Manual LOW SPEED BOOSTER PUMP HIGH SPEED FILTER PUMP AUX 1 AUX 2 1915 0895 Sta-Rite Industries Basic Training Manual THIRD EDITION Hydraulics Pumps Motors Filtration Heaters 2668 0397NF 2003 Sta-Rite Industries,

More information

Entrained Gas Diagnostic with Intelligent Differential Pressure Transmitter

Entrained Gas Diagnostic with Intelligent Differential Pressure Transmitter January Page Entrained Gas Diagnostic with Intelligent Differential Pressure Transmitter Dave Wehrs - Director, Pressure Engineering Andrew Klosinski - Application Engineer, Pressure Diagnostics Emerson

More information

measurement, but almost any pipe elbow can be calibrated Elbow meters are not as potentially accurate as venturi,

measurement, but almost any pipe elbow can be calibrated Elbow meters are not as potentially accurate as venturi, Lecture 14 Flow Measurement in Pipes I. Elbow Meters An elbow in a pipe can be used as a flow measuring device much in the same way as a venturi or orifice plate The head differential across the elbow

More information

Fluid Dynamics Viscosity. Dave Foster Department of Chemical Engineering University of Rochester Email: dafoster@che

Fluid Dynamics Viscosity. Dave Foster Department of Chemical Engineering University of Rochester Email: dafoster@che Fluid Dynamics Viscosity Dave Foster Department of Chemical Engineering University of Rochester Email: dafoster@che che.rochester.eduedu 1 Chemical Engineering What do Chemical Engineers Do? Manufacturing

More information

Fire Pump Plan Review March 2010

Fire Pump Plan Review March 2010 Fire Pump Plan Review March 2010 Date of Review: / / Permit Number: Business/Building Name: Address of Project: Designer Name: Designer s Phone: Contractor: Contractor s Phone: Occupancy Classification:

More information

Wet gas compressor capacity limits

Wet gas compressor capacity limits Understanding Centrifugal Compressor Performance in a Connected Process System Scott Golden, Scott A. Fulton and Daryl W. Hanson Process Consulting Services Inc., Houston, Texas Wet gas compressor capacity

More information

UNIT Engineering: Measurement Technology Flow (SCQF level 6)

UNIT Engineering: Measurement Technology Flow (SCQF level 6) National Unit Specification: general information CODE H0W6 12 SUMMARY This Unit can be delivered as part of a National Qualification Group Award but can also be taken as a free-standing Unit. This Unit

More information

TECHNICAL BULLETIN 4 USE OF MAZZEI INJECTORS IN WATER-WELL / PRESSURE TANK APPLICATIONS

TECHNICAL BULLETIN 4 USE OF MAZZEI INJECTORS IN WATER-WELL / PRESSURE TANK APPLICATIONS TECHNICAL BULLETIN No. 4 USE OF MAZZEI INJECTORS IN WATER-WELL / PRESSURE TANK APPLICATIONS The selection, installation and use of Mazzei Injectors in water-well/pressure tank systems is quite straightforward.

More information

ELECTRIC/DIESEL FIRE PUMP CHECK LIST

ELECTRIC/DIESEL FIRE PUMP CHECK LIST BUILDING NAME: DESIGNER: SCO REPRESENTATIVE: PUMP MANUF.: LOCATION: INSTALLER: DATE: OWNER NAME: INSTALLATION Certificate for flushing and hydrostatic test furnished Piping been hydrostatically tested

More information

Fluid Dynamics Basics

Fluid Dynamics Basics Fluid Dynamics Basics Bernoulli s Equation A very important equation in fluid dynamics is the Bernoulli equation. This equation has four variables: velocity ( ), elevation ( ), pressure ( ), and density

More information

Technical Bulletin TB8102 Rupture Disc Sizing

Technical Bulletin TB8102 Rupture Disc Sizing Technical Bulletin TB8102 Rupture Disc Sizing The objective of this bulletin is to provide detailed guidance for sizing rupture discs using standard methodologies found in ASME Section VIII Div. 1, API

More information

Hydraulic losses in pipes

Hydraulic losses in pipes Hydraulic losses in pipes Henryk Kudela Contents 1 Viscous flows in pipes 1 1.1 Moody Chart.................................... 2 1.2 Types of Fluid Flow Problems........................... 5 1.3 Minor

More information

Innovative Mass Air Flow Measurement

Innovative Mass Air Flow Measurement Innovative Mass Air Flow Measurement Mr. Lucas Howard, Mr. Jonathan Hayes, Mrs. Pat Buford, Dr. Wayne Helmer, Mechanical Engineering/Electrical Engineering Arkansas Tech University Russellville, Arkansas

More information

Aeration Air & Digester Gas Flow Metering Using Thermal Mass Technology. HWEA 2011 Conference Craig S. Johnson

Aeration Air & Digester Gas Flow Metering Using Thermal Mass Technology. HWEA 2011 Conference Craig S. Johnson Aeration Air & Digester Gas Flow Metering Using Thermal Mass Technology HWEA 2011 Conference Craig S. Johnson Presentation Overview Introduction Aeration Air & Digester gas challenges Gas flow metering

More information

BASIC HYDRONIC SYSTEM DESIGN

BASIC HYDRONIC SYSTEM DESIGN Hydronic Systems BASIC HYDRONIC SYSTEM DESIGN FCU FCU FCU FCU FCU FCU Terminal Units Fan Coils, Chilled Beams, Finned Tube, Radiant, etc. Distribution Piping AS-1 Primary Pumps P-1 & P-2 P-1 P-2 ET-1 P-B-1

More information

Selecting a Vertical Turbine Pump (Information required from client)

Selecting a Vertical Turbine Pump (Information required from client) Selecting a Vertical Turbine Pump (Information required from client) 1. Liquid to be pumped: (Note: If liquid is not clear water, the following must also be ascertained). a. Foreign material present in

More information

Centrifugal Fans and Pumps are sized to meet the maximum

Centrifugal Fans and Pumps are sized to meet the maximum Fans and Pumps are sized to meet the maximum flow rate required by the system. System conditions frequently require reducing the flow rate. Throttling and bypass devices dampers and valves are installed

More information

ME332 FLUID MECHANICS LABORATORY

ME332 FLUID MECHANICS LABORATORY ME332 FLUID MECHANICS LABORATORY Mihir Sen Department of Aerospace and Mechanical Engineering University of Notre Dame Notre Dame, IN 46556 Contents January 8, 2003 Spring 2003 Before break: Experiments

More information

Flow Measurement. Reference - Flow Measurement FUNDAMENTALS. ρ = fluid density (lb/ft3 or kg/m3)

Flow Measurement. Reference - Flow Measurement FUNDAMENTALS. ρ = fluid density (lb/ft3 or kg/m3) Flow Measurement FUDAMETALS Flowmetering terms can often seem cryptic Here are definitions of some of the most commonly used ACCURACY Accuracy is a quantity defining the limit that errs will not exceed

More information

CHEMCAD 6.0 SIZING TOOLS

CHEMCAD 6.0 SIZING TOOLS CHEMCAD 6.0 SIZING TOOLS PIPES, PUMPS, METERS AND VALVES By John E. Edwards CONTENTS Introduction... 3 Pipe UnitOp Validation Case... 5 Control Valve Liquid Sizing Tool... 8 Control Valve Gas and Vapour

More information

Valve Sizing. Te chnic al Bulletin. Flow Calculation Principles. Scope. Sizing Valves. Safe Product Selection. www.swagelok.com

Valve Sizing. Te chnic al Bulletin. Flow Calculation Principles. Scope. Sizing Valves. Safe Product Selection. www.swagelok.com www.swagelok.com Valve Sizing Te chnic al Bulletin Scope Valve size often is described by the nominal size of the end connections, but a more important measure is the flow that the valve can provide. And

More information

Pump Formulas Imperial and SI Units

Pump Formulas Imperial and SI Units Pump Formulas Imperial and Pressure to Head H = head, ft P = pressure, psi H = head, m P = pressure, bar Mass Flow to Volumetric Flow ṁ = mass flow, lbm/h ρ = fluid density, lbm/ft 3 ṁ = mass flow, kg/h

More information

4.What is the appropriate dimensionless parameter to use in comparing flow types? YOUR ANSWER: The Reynolds Number, Re.

4.What is the appropriate dimensionless parameter to use in comparing flow types? YOUR ANSWER: The Reynolds Number, Re. CHAPTER 08 1. What is most likely to be the main driving force in pipe flow? A. Gravity B. A pressure gradient C. Vacuum 2.What is a general description of the flow rate in laminar flow? A. Small B. Large

More information

Grant Agreement No. 228296 SFERA. Solar Facilities for the European Research Area SEVENTH FRAMEWORK PROGRAMME. Capacities Specific Programme

Grant Agreement No. 228296 SFERA. Solar Facilities for the European Research Area SEVENTH FRAMEWORK PROGRAMME. Capacities Specific Programme Grant Agreement No. 228296 SFERA Solar Facilities for the European Research Area SEVENTH FRAMEWORK PROGRAMME Capacities Specific Programme Research Infrastructures Integrating Activity - Combination of

More information

Friction Loss of Pulp Suspensions in Pipe

Friction Loss of Pulp Suspensions in Pipe Friction Loss of Pulp Suspensions in Pipe I. INTRODUCTION In any stock piping system, the pump provides flow and develops hydraulic pressure (head) to overcome the differential in head between two points.

More information

A10VSO Nominal size 18 see RD 92712 A10VSO Nominal size 28...140 see RD 92711

A10VSO Nominal size 18 see RD 92712 A10VSO Nominal size 28...140 see RD 92711 A10VO Nominal size 18 see RD 92712 A10VO Nominal size 28...140 see RD 92711 The variable displacement axial piston pump A10VO in swashplate design was designed for hydrostatic drives in open circuits.

More information

CONTROL VALVE PRESSURE DROP AND SIZING

CONTROL VALVE PRESSURE DROP AND SIZING CONTENT Chapter Description Page I Purpose of Control Valve II Type and Main Components of Control Valve 3 III Power 5 IV. Pressure Drop Across Control Valve 7 V. Symbols and Units 10 VI. Unit Conversion

More information

In-Line Air Separators

In-Line Air Separators Air Elimination & Control In-Line Air Separators The AC models of air separators deliver all the quality and performance you expect from Taco products. They are built to last with shell, heads and ANSI

More information

The Unique Accelabar Flow Meter

The Unique Accelabar Flow Meter The Unique Accelabar Flow Meter The Accelabar is a new and unique flow meter that combines two differential pressure technologies to produce operating ranges never before attainable in a single flow meter.

More information

Modeling Fluid Systems

Modeling Fluid Systems Modeling Fluid Systems The prevalent use of fluid (hydraulic) circuitry in machines tool applications, aircraft control systems, and similar operations occurs because of such factors such as accuracy,

More information

Custody Transfer Measurement. with the V-Cone Flowmeter

Custody Transfer Measurement. with the V-Cone Flowmeter Custody Transfer Measurement with the V-Cone Flowmeter Stephen A. Ifft McCrometer Inc. Hemet, California, USA Abstract This paper will discuss the approval of the McCrometer V-Cone flowmeter for custody

More information

SIZING OF WATER PIPING SYSTEM

SIZING OF WATER PIPING SYSTEM SIZING OF WATER PIPING SYSTEM SECTION E101 GENERAL E101.1 Scope. E101.1.1 This appendix outlines two procedures for sizing a water piping system (see Sections E103.3 and E201.1). The design procedures

More information

PEERLESS PUMP COMPANY SYSTEM ANALYSIS FOR PUMPING EQUIPMENT SELECTION

PEERLESS PUMP COMPANY SYSTEM ANALYSIS FOR PUMPING EQUIPMENT SELECTION PEERLESS PUMP COMPANY SYSTEM ANALYSIS FOR PUMPING EQUIPMENT SELECTION Peerless Pump Company 005 Dr. Martin Luther King Jr. Street P.O. Box 706 Indianapolis, Indiana 4607-706 Phone: (317) 95-9661 Fax: (317)

More information

Approved: Ernesto Gutierrez-Miravete, Engineering Project Adviser

Approved: Ernesto Gutierrez-Miravete, Engineering Project Adviser A Design Study of the Heat Removal System for the Propulsion Machinery of a Nuclear Powered Ship by Scott E. Misiaszek An Engineering Project Submitted to the Graduate Faculty of Rensselaer Polytechnic

More information

MOBILE FIRE - RESCUE DEPARTMENT FIRE CODE ADMINISTRATION

MOBILE FIRE - RESCUE DEPARTMENT FIRE CODE ADMINISTRATION MOBILE FIRE - RESCUE DEPARTMENT FIRE CODE ADMINISTRATION Fire Pump Plan Review 2009 International Fire Code and NFPA 20 Date of Review / / BLD201 - Project Address: Project Name: Contractor s Business

More information

Theory overview of flow measurement using differential pressure devices based on ISO-5167 standard.

Theory overview of flow measurement using differential pressure devices based on ISO-5167 standard. Theory overview of flow measurement using differential pressure devices based on ISO-567 standard. rian FL40 flow computer description. Flow Cad software users manual. Technical note, Differential pressure

More information

Flow Accelerated Corrosion. in Angra 1 and Angra 2 Nuclear Power Plants. Lucio Ferrari Tomás D. S. Costa

Flow Accelerated Corrosion. in Angra 1 and Angra 2 Nuclear Power Plants. Lucio Ferrari Tomás D. S. Costa Flow Accelerated Corrosion in Angra 1 and Angra Nuclear Power Plants Lucio Ferrari Tomás D. S. Costa December/008 Angra Site Angra 1 Power: 657 MW Start of Operation: 198 Westinghouse Angra Power: 1390

More information

Basic Concepts of Ventilation Design

Basic Concepts of Ventilation Design Building Design and Engineering Approaches to Airborne Infection Control Basic Concepts of Ventilation Design Jack Price General Principles of Ventilation Introduction Need for ventilation: Comfort Contamination

More information

Rosemount Orifice Plate in Wet Gas

Rosemount Orifice Plate in Wet Gas 00870-0100-4810 January 2006 Page 1 Rosemount Orifice Plate in Wet Gas This paper discusses the phenomenon of wet gas measurement, definitions, and the need to accurately measure this mixture. This paper

More information

Avoiding Pump Wear in Centrifugal Pumps

Avoiding Pump Wear in Centrifugal Pumps Pump Wear Avoiding Pump Wear in Centrifugal Pumps Introduction: In the moment of starting a new pump, that pump is headed for a day when it will need repair even if the design and operation is correct.

More information

HYDRAULIC ANALYSIS OF PIPE LINED WITH MADISON S 100% SOLIDS STRUCTURAL POLYURETHANE COATINGS

HYDRAULIC ANALYSIS OF PIPE LINED WITH MADISON S 100% SOLIDS STRUCTURAL POLYURETHANE COATINGS HYDRAULIC ANALYSIS OF PIPE LINED WITH MADISON S 100% SOLIDS STRUCTURAL POLYURETHANE COATINGS Shiwei William Guan, Ph.D. Vice President, R&D and International Business Madison Chemical Industries Inc. 490

More information

HOW TO ALIGN THE UNIT

HOW TO ALIGN THE UNIT First check that the pump has not been damaged during trasport. Place the fondation bolts loosely in the holes of the base plate and align the plate by using shims. Check alignment with a spirit level.

More information

Pump Maintenance - Repair

Pump Maintenance - Repair Pump Maintenance - Repair Brian Trombly Mo Droppers Cummins Bridgeway, Gaylord, Mi The basic centrifugal pump consists of two main elements: 1. The rotating element which includes an impeller and a shaft.

More information

Nozzle Loads, Piping Stresses, and the Effect of Piping on Equipment

Nozzle Loads, Piping Stresses, and the Effect of Piping on Equipment Nozzle Loads, Piping Stresses, and the Effect of Piping on Equipment By Patty Brown & Mark van Ginhoven November 13, 2009 1 CA 2009 Fluor Corporation. All Rights Reserved. Topics Covered Introduction Nozzle

More information

New Method for Accurate High Reynolds Metering Uses Water Calibration for Significant Cost Savings White Paper

New Method for Accurate High Reynolds Metering Uses Water Calibration for Significant Cost Savings White Paper New Method for Accurate High Reynolds Metering Uses Water Calibration for Significant Cost Savings White Paper Page 1 of 3 White Paper Jonathan Hollist, V-Cone Engineer Nick Voss, V-Cone Product Manager

More information

Secondary Refrigerant Pipe Flow Rates

Secondary Refrigerant Pipe Flow Rates Secondary Refrigerant Pipe Res 1.0 Introduction The purpose of this technical bulletin is to provide allowable velocities and flow res for a range of various fluids for a range of pipe sizes. The velocities

More information

Chapter 10. Flow Rate. Flow Rate. Flow Measurements. The velocity of the flow is described at any

Chapter 10. Flow Rate. Flow Rate. Flow Measurements. The velocity of the flow is described at any Chapter 10 Flow Measurements Material from Theory and Design for Mechanical Measurements; Figliola, Third Edition Flow Rate Flow rate can be expressed in terms of volume flow rate (volume/time) or mass

More information

PUMPS STEAM TURBINES BUILDING & FIRE WASTEWATER SERVICE PUMP CLINIC 22 VISCOSITY

PUMPS STEAM TURBINES BUILDING & FIRE WASTEWATER SERVICE PUMP CLINIC 22 VISCOSITY PUMP CLINIC 22 VISCOSITY The viscosity of a fluid is that property which tends to resist a shearing force. It can be thought of as the internal friction resulting when one layer of fluid is made to move

More information

= water horsepower WHP brake horsepower QH WHP = (222) ( 33,000 ft-lbs/min-hp)( 7.481 gal/ft ) 1 HP=0.746 kw

= water horsepower WHP brake horsepower QH WHP = (222) ( 33,000 ft-lbs/min-hp)( 7.481 gal/ft ) 1 HP=0.746 kw Lecture 11 Pumps & System Curves I. Pump Efficiency and Power Pump efficiency, E pump E pump = water horsepower WHP brake horsepower = BHP (221) where brake horsepower refers to the input power needed

More information

A MTR FUEL ELEMENT FLOW DISTRIBUTION MEASUREMENT PRELIMINARY RESULTS

A MTR FUEL ELEMENT FLOW DISTRIBUTION MEASUREMENT PRELIMINARY RESULTS A MTR FUEL ELEMENT FLOW DISTRIBUTION MEASUREMENT PRELIMINARY RESULTS W. M. Torres, P. E. Umbehaun, D. A. Andrade and J. A. B. Souza Centro de Engenharia Nuclear Instituto de Pesquisas Energéticas e Nucleares

More information

The Versatile Differential Pressure Transmitter. By David Gunn Honeywell Process Solutions

The Versatile Differential Pressure Transmitter. By David Gunn Honeywell Process Solutions The Versatile Differential Pressure Transmitter By David Gunn Honeywell Process Solutions The Versatile Differential Pressure Transmitter 2 Table of Contents Abstract... 3 Pressure Fundamentals... 3 Applications...

More information

Figure 1. Head losses in a pipe

Figure 1. Head losses in a pipe 53:071 Principles of Hydraulics Laboratory Experiment #1 ENERGY AND HYDRAULIC GRADE LINES IN WATER PIPE SYSTEMS Principle The energy of a real fluid decreases as it moves through a pipe. The energy budget

More information

FLUID MECHANICS. TUTORIAL No.7 FLUID FORCES. When you have completed this tutorial you should be able to. Solve forces due to pressure difference.

FLUID MECHANICS. TUTORIAL No.7 FLUID FORCES. When you have completed this tutorial you should be able to. Solve forces due to pressure difference. FLUID MECHANICS TUTORIAL No.7 FLUID FORCES When you have completed this tutorial you should be able to Solve forces due to pressure difference. Solve problems due to momentum changes. Solve problems involving

More information

Compact Medium-pressure Vane Pump

Compact Medium-pressure Vane Pump Compact Medium-pressure Vane Pump Features The straight vane type structure realizes compact and lightweight design which brings greater cost effectiveness. These vane pumps with a maximum pressure of

More information

Pump ED 101. Positive Displacement Pumps. Part I Reciprocating Pumps

Pump ED 101. Positive Displacement Pumps. Part I Reciprocating Pumps Pump ED 101 Positive Displacement Pumps Part I Reciprocating Pumps Joe Evans, Ph.D http://www.pumped101.com There are many pump designs that fall into the positive displacement category but, for the most

More information