STABILO LUXE VENETIAN BLINDS
|
|
- Phoebe White
- 7 years ago
- Views:
Transcription
1
2 STABILO LUXE VENETIAN BLINDS Stabilo Luxe 80, 80-F Venetian blinds - External blinds using 80mm wide adjustable and retractable slats. These blinds have the highest degree of control over the widest possible range due to the large range of adjustment of the slats. There are two kinds using flanged or non-flanged slats. In both cases the slats are made of flexible aluium utilizing a burned-in painting method for surface treatment. The flanged version accommodates flanges on both edges. Due to this the wind resistance of slats is increased and wider blinds can be installed. The non-flanged or flat slats are slightly cambered and are flexible. Strong winds can bend the slats, but due to their flexibility they regain their original shape. The two systems mainly differ in their application s scope. The flat slatted system takes up significantly less space above the window. Guidance of slats can be achieved using either guide rails or cables. The guide rail is an extruded aluium profile in which the guiding pins are running. These pins located on the end of the slats. In case of the cable guided system the cable guides the slats via oval pressed in holes. The rail guided system provides a more rigid guidance but the rails still can be seen in retracted state. The horizontal position of slats has been ensured by using a bottom rail, which is heavier than the slats. Flanged and non-flanged slats The blinds can be operated using a hand crank or a motor. A single hand crank or motor can operate multiple blinds utilizing a clutch mounted on their shafts. The motor or the manual drive system placed into head rail, which is on the top of the blind system. The drive transmitted to the rotating units via an appropriately stiff aluium shaft. These units are moving the slats in the vertical direction and also tilting them. The head rail and the mechanism within protected using an aluium cover. Depending on the installation, this protective cover can be 'U', 'L' or 'I' shaped. The head rail with motor The head rail with hand crank
3 STABILO LUXE 80-F Stabilo Luxe 80-F blind - External shading system with 80 mm wide non flanged slats. One of the major advantages of using planar slats is their small retracted height. Using this with a cable guided system can make the blind almost invisible on the facade in the retracted state. The non flanged or flat slats are slightly cambered and they are extremely flexible. Their material is a special 5754 H48 ALMG3 aluium alloy. Strong winds can bend the slats, but due to their flexibility they regain their original shape. Guidance of slats has been done using a cable system. The slats mostly guided on both of their ends. When using wider blinds, above 2.75m we install more wires. The cables are guiding the slats via oval holes on their ends. The materials of these cables are stainless steel coated with UV resistant plastic sheathing. This ensures a smooth and noiseless operation of the slats. Stabilo Luxe 80-F There is a special feature on cable guided Stabilo Luxe 80-F system. The punching of the oval holes also followed by an asymmetric deformation which results in an increased slat deflection when compared to a plain oval hole. This way the light can be shut off to a larger degree. There are further special perforations on the slats. One of them is a double horseshoe shaped punching which supports the ladder string. The other is a hole for the retracting string between these horseshoe-shaped holes, keeping the retracting string in the centre of the ladder string. There is another type of hole for the retracting string. This hole is flanged with its own material, this way the slat is not damaging the retraction string. As opposed to using a plastic flange ring there is no UV resistance problem. Flat slat Wire tensioning consoles The retraction strap made of high tensile strength material; it is either 6 or 8mm wide. The width always based on the size of the blind. To anchor the cables, we use different type of consoles. This depends on the installation. The consoles are adjustable, this way the ideal vertical position of the cables ensured. Protection covers MAJOR DIMENSIONS Width Height Area Area weight Motor driven 0.58m 4.40m* 19,8m² 2.0kg/m² 7.2kg/m² Manual 0.42m 4.40m* 9m² 2.0kg/m² 6.1kg/m² * above 2.75m we install more wires
4 STABILO LUXE 80 with guide rails Stabilo Luxe 80 blind - External shading system with 80 mm wide flanged slats. Both edges of the slats are flanged using a set of special rollers. This results in a 4mm diameter enclosed section. Due to this the wind resistance of the slats increased and wider blinds can be built. There are guide profiles riveted in the slat ends. These are running in guide rails. The guide profiles made of UV resistant plastic; therefore the sun doesn t damage them. The guide rails lined with two rubber inserts each. These insert has a dumping effect on the noise generated by the wind or the slats. Stabilo Luxe 80 We use different type of consoles for the mounting of the guide rails which depends on the kind of installation. These consoles can support the guide rails on the side or from behind. They are adjustable; this ensures the perfect vertical position and distance from the facade. The lifting strap made of high tensile strength (1000N) terylene and is 6 or 8mm wide. The width always based on the size of the blind. These straps made using special weaving techniques. They are UV, stretch, wear, and shrink resistant. Guide rail consoles The hole for the lifting string is flanged using its own material, this way the slats cannot damage the string. As opposed to using plastic flange rings there is no UV resistance problem. Guide rails The flanged slat system has a bigger retracted height; therefore its appearance is more striking. This effect is further enhanced by the visible guide rails. This can be emphasized even more by installing the system in front of the facade. MAJOR DIMENSIONS Width Height Area Area weight Motor driven 0.58m 4.40m 19,8m² 2.7kg 8.3kg Manual 0.42m 4.40m 9m² 2.6kg 7.2kg
5 STABILO LUXE 80 with cable Stabilo Luxe 80 blind - External shading system with 80 mm wide flanged slats. Both edges of the slats are flanged using a set of special rollers. This results in a 4mm diameter enclosed section. Due to this the wind resistance of the slats increased and wider blinds can be built. Guidance of slats has been done using a cable system. The slats mostly guided on both of their ends. When using wider blinds, above 2.75m we install more wires. The cables are guiding the slats via oval holes on their ends. The materials of these cables are stainless steel coated with UV resistant plastic sheathing. This ensures a smooth and noiseless operation of the slats. Stabilo Luxe 80 To anchor the cables, we use different type of consoles. This depends on the installation. The consoles are adjustable, this way the ideal vertical position of the cables ensured. The lifting strap made of high tensile strength (1000N) Terylene and is 6 or 8mm wide. The width always based on the size of the blind. These straps made using special weaving techniques. They are UV, stretch, wear, and shrink resistant. The hole for the lifting string is flanged using its own material, this way the slats cannot damage the string. As opposed to using plastic flange rings there is no UV resistance problem. Wire tensioning consoles The flanged slat system has a bigger retracted height than the flat slatted, therefore its appearance is more emphasized on the facade. This blind can be installed behind the facade cover. Due to the cable guided system it is almost invisible in the retracted state. MAJOR DIMENSIONS Width Height Area Area weight Motor driven 0.58m 4.40m* 19,8m² 6.7kg/m² 8.0kg/m² Manual 0.42m 4.40m* 9m² 2.0kg/m² 6.9kg/m² * above 2.75m we install more wires
6 INSTALLMENT OPTIONS 1 Installation coincides with facade plane. Installation behind facade 120,0 50,0 128,0 'I' type protection cover VARIABLE VARIABLE VARIABLE VARIABLE Flat slat Tensioning wire Wire tensioning console * It is worth to construct the facade cover console in such way that it can accommodate the blind and its cover. Required space envelope: 120mm + 30mm. Installation in front of the facade, lifted up. 'U' type protection cover Guide rail Guide console Aluium cover plate Flat slate Tensioning wire Wire tensioning console VARIABLE VARIABLE VARIABLE VARIABLE 120,0 128,0 120,0 * It is worth to construct the facade cover console in such way that it can accommodate the blind and its cover. Required space envelope: 120mm + 30mm. 'L' type protection cover Flat slat Tensioning wire Wire tensioning console Installation in front of the facade
7 INSTALLMENT OPTIONS 2 Installation in front of the facade, lifted up Installation on window extension 'I' type protective cover 50,0 135,0 VARIABLE 205,0 Extruded protective cover Guide rail Guide console Tensioning wire Wire tensioning console ~10,0 127,0 127,0 VARIABLE VARIABLE * The consoles mounted on the window, their extra load must be considered. It is particularly important to accurately install the windows. * The heightening should match the height of the blind. Hand crank routing on multiple windows Hand crank installation on the hinge side Drive system of blind Drive system of blind 80,0 23,5 127,0 23,5 80,0 23,5 23,5 20,0 20,0 20,0 20,0 20,0 20,0 80,0 Hand crank route Hand crank Hand crank route Hand crank 40,0 * The drive system is always facing the hand crank. As a consequence, the inside and outside installation surfaces also have to be facing to each other. The routing can also be done by sinking the drive system into a recess.
8 DIACENTER LABORATÓRIUM ÉS IRODAHÁZ BUDAPEST BUDAPESTI KOMMUNIKÁCIÓS FŐISKOLA BUDAPEST ALBERT HACKERODT HUNGÁRIA KFT. GYŐR KÁLMÁN IMRE KULTÚRÁLIS KÖZPONT SIÓFOK SAP IRODAHÁZ BUDAPEST
The load carrier system designed for professionals
The load carrier system designed for professionals THULE PROFESSIONAL The rugged time-saving system Thule Professional is a load carrier system from the world leader in utility transportation. Every aspect
More informationBAGGAGE HANDLING SYSTEMS. Trastecnica S.p.A. Handling Baggage Systems Edition 2002 - Rev. 00-1 -
BAGGAGE HANDLING SYSTEMS Trastecnica S.p.A. Handling Baggage Systems Edition 2002 - Rev. 00-1 - TECHNICAL SPECIFICS INDEX Check-in with one conveyor 4 Scales 6 Belt Conveyors 8 Take away 9 Feeder and Belt
More informationV80 HEAD DETAIL - SECTION VIEW DRAWING SCALE 1:2. Dwg. No. V10101. 13mm min. 85mm. 72mm 95mm 65mm. 26mm. 10mm 60mm 75mm. 135mm.
13mm min. 72mm 95mm 65mm 85mm 26mm 10mm 60mm 75mm 135mm 145mm V80 HEAD DETAIL - SECTION VIEW Dwg. No. V10101 Manually operated blind with gearbox showing 90 & 45 degree crank penetrations in section view.
More informationAluminium systems profile selection
Aluminium systems profile selection The purpose of this document is to summarise the way that aluminium profile selection should be made, based on the strength requirements for each application. Curtain
More informationMONDOATHENS BASKETBALL SET (Reference PK110)
MONDOATHENS BASKETBALL SET (Reference PK110) DESCRIPTION The MONDOATHENS backstop unit is mainly designed for multi-sports pavilions and installations where the highest-level basketball competitions are
More informationCable Trays Technical Instructions & Specifications
Cable Trays Technical Instructions & Specifications Products Catalogue Objective and Structure The company s main objective is the supply of quality products, with respect to: practical design increased
More informationSECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2
More informationDiameter. Swift Lift Round Recess Plug. Note: The diameter of the narrow recess plug is the same as the diameter of the round recess plug.
P-5 The P-5 is hot forged from carbon steel. The formed head provis spherical seating that the Lifting Eye engages, while a disc-shaped foot is embedd in the concrete. Due to its being a forged part, the
More informationBOQ SPECIFICATIONS. The Blind system consist of a coated aluminium tube of 38 mm diameter with provision of fabric clamping.
BOQ SPECIFICATIONS VERTICAL BLINDS Vertical Blinds made of glass fibre fabrics in width 5 (or 4 ). Minimum overlapping of ¾ in fabric. Top aluminium anodized rail of 1.4 mm thickness. 2 inch wide channel
More informationQuarry & Recycling Products
Quarry & Recycling Products CONTENTS Woven mesh screens Perforated screen plates Rubber & Polyurethane screens Walkways & Steps Ordering Information Further Information PAGE 3 6 8 9 10 11 Graepel has a
More informationSHUTTER INSTALLATION INSTRUCTIONS. AUGUST 2006 Version 2
SHUTTER INSTALLATION INSTRUCTIONS AUGUST 2006 Version 2 All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
More informationPrecision Vise Combinations
Precision Vise Combinations PanaVise vises and work holding tools have hundreds of uses limited only by your imagination! Each vise allows the head to Tilt, Turn & Rotate and position your work anywhere
More informationValu Guide Sheaths. Valu Guide Inserts. Optional Valu Guide Inserts. Typical Properties of Valu Guide Rail. and Hardware.
14 gauge stainless steel The Original, Long Life Sanitary Guide Rail Valu Guide rail incorporates two outstanding materials: stainless steel and UHMW. The 14 ga. stainless steel sheath provides rigid streamlined
More informationIntegrated Manhole Ladder System
Application: This innovative product has been designed to provide safe access and egress to precast concrete manholes and inspection chambers. It can also be used within any other underground concrete
More informationClad Direct Glaze Window Installation Instructions
Clad Direct Glaze Window Installation Instructions Sill flashing and sealing: 2. An overview of the proper flashing sequence is shown in figure 1. Please read entire installation instructions carefully
More informationRack installation instructions
Rack installation instructions Review the documentation that comes with the rack cabinet for safety and cabling information. Before you install the server in a rack cabinet, review the following guidelines:
More informationNow available with full IP65 rating: Protection from dust and water jets NEW: K470 Plus covered containers
Now available with full IP65 rating: Protection from dust and water jets NEW: K470 Plus covered containers Universal container K 470 the original since 1950 Often copied but never equalled or bettered
More informationResidential Garage Door Terminology
A Air Infiltration: The leakage or passage of air through a door system Anodize: A hard non-corrosive oxide film on the surface of aluminum Astragal: A compressible or deformable seal provided on the bottom
More information#25 The Basics of Lightweight Conveyor Belting
#25 The Basics of Lightweight Conveyor Belting The overall belting market share for lightweight conveyor belting has increased modestly over the past couple of decades. The primary reasons for the increase
More informationSecurity Shutters, Retractable Security Gates, SeceuroBar & Aluminium Folding Shutter
Security Shutters, Retractable Security Gates, SeceuroBar & Aluminium Folding Shutter C38 Vision 38 showing in-line punching Continental Range Experience Syston Doors have been manufacturing & supplying
More informationInstallation instructions of the MIDI-Heki roof light with operating bar, with crank or electrical version
Installation instructions of the MIDI-Heki roof light with operating bar, with crank or electrical version with operating bar with crank electrical version 1. Prerequisite for a correct installation of
More information1.1 DIMENSIONS AND WEIGHT PAG. 2 1.2 LOAD CENTRE FOR LIFTING PAG. 2 1.3 STORAGE CONDITIONS PAG. 2
TRANSPORT AND INSTALLATION. DIMENSIONS AND WEIGHT PAG.. LOAD CENTRE FOR LIFTING PAG..3 STORAGE CONDITIONS PAG. STARTING. INSTALLATION PAG.. SPACE REQUIREMENTS PAG. 3.3 ELECTRIC CONNECTION PAG. 3 3 DESCRIPTION
More informationInForm Tables and Base Cabinets
System tables 30 mm thick, coated with laminate, selection of 3 different front edges: Postformed edge, 70 mm high Edge band, 3 mm thick FlexiLine edge, replaceable. Permitted surface load on the tabletop:
More informationThe Roskilde Domes 2011 and 2012
Proceedings of the International Association for Shell and Spatial Structures (IASS) Symposium 2013 BEYOND THE LIMITS OF MAN 23-27 September, Wroclaw University of Technology, Poland J.B. Obrębski and
More informationGo-kart for little race-drivers
Go-kart for little race-drivers Drill and drive. Go-kart What it lacks in speed, it more than makes up for in fun: the go-kart will excite little race-drivers. 1 Introduction It s only a go-kart, but it
More informationCOIL PAC. Subec AB, Sprängarvägen 16, 132 38 Saltsjö-Boo, Sweden, Tel.: +46 8 884633, Fax: +46 8 977658, e-mail: info@subec.se
COIL PAC Subec AB, Sprängarvägen 16, 132 38 Saltsjö-Boo, Sweden, Tel.: +46 8 884633, Fax: +46 8 977658, e-mail: info@subec.se Description of the machine Coil Pac 240 und Coil Pac 400 are two types of
More informationType 1, 3, & 3R Enclosures
Junction oxes Type 1 Screw over....................................................................... 50-53 Junction oxes Type 1 Hinge over........................................................................
More informationRemoving chips is a method for producing plastic threads of small diameters and high batches, which cause frequent failures of thread punches.
Plastic Threads Technical University of Gabrovo Yordanka Atanasova Threads in plastic products can be produced in three ways: a) by direct moulding with thread punch or die; b) by placing a threaded metal
More informationRINGFEDER. Automatic Hook Couplings for Road and Cross Country Vehicles. TYPE RUwg. Prospect
RINGFEDER E 07 00 Prospect Automatic Hook Couplings for Road and Cross Country Vehicles TYPE RUwg Automatic Hook Couplings Types RUwg K O D, K 1 D, K 2 D, K 3 D, K 4 D for towing eye according to VG 74059
More informationRear Impact Guard TEST METHOD 223. Standards and Regulations Division. Issued: December 2003
Transport Canada Safety and Security Road Safety Transports Canada Sécurité et sûreté Sécurité routière Standards and Regulations Division TEST METHOD 223 Rear Impact Guard Issued: December 2003 Standards
More informationWindows, French doors, folding windows, terrace doors SFB 1074 with low U-values
Windows, French doors, folding windows, terrace doors SFB 1074 with low U-values SFB 1074 is available in two versions. In the first version the profiles are insulated with 30 mm glass fibre reinforced
More informationInstallation guide for the SafeLine type anchorage device. Tested in compliance with EN 795: 1996. No.: SE-...
Installation guide for the SafeLine type anchorage device Tested in compliance with EN 795: 1996 No.: SE-... Version: 09.10.2008 SE 67 Subject to technical alterations! Contents 1. General information
More informationAwning Instructions. Standard Manual 1.5m to 4.5m
Awning Instructions Standard Manual 1.5m to 4.5m English Standard Manual Instructions Contents Warning 1.5m 3.0m Awnings 4 x Expansion bolts (2 per bracket)** 2 x brackets 1 x Awning 1 x Winder handle
More informationVideo Conferencing Solutions
Video Conferencing Solutions Innovative Products To Make Your Video Conferencing More Effective Just like the internet, video conferencing is evolving rapidly. New efficiencies, benefits, and audiences
More informationGK Packing System Welding Instructions
GK Packing System Welding Instructions Roxtec GmbH Neuer Höltigbaum 1-3, 22143 Hamburg GERMANY Tel +49 (040) 657398-0, Fax +49 (040) 657398-50 EMAIL info@de.roxtec.com, www.roxtec.de Welding instructions
More informationMODEL HSR-007 Direct Drive Rolling Steel
MODEL HSR-007 Direct Drive Rolling Steel 200 Fairview Road, Unit #2, Barrie, Ontario L4N 8Z8 Tel: 866-792-9968 or 705-792-9968 Fax: 705-735-9564 www.tnrdoors.com email: info@tnrdoors.com Model HSR-007
More informationBelt Drives and Chain Drives. Power Train. Power Train
Belt Drives and Chain Drives Material comes for Mott, 2002 and Kurtz, 1999 Power Train A power train transmits power from an engine or motor to the load. Some of the most common power trains include: Flexible
More informationPREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS
SYSTEM COMPONENTS PREASSEMBLED ELEMENTS FOR FIFTING AND SLIDING DOORS s r ood gn i d i l s dna gn i t f i f r o f s t neme l e de l bme s s ae r P PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS These
More informationDSM http://www.dsmmfg.com 1 (800) 886-6376
DESIGN GUIDE FOR BENT SHEET METAL This guide discusses how the bends are made, what thicknesses of sheet metal are commonly used, recommended bend radius to use when modeling the part, some practical limits
More informationProduct Information 19 / 45HU Data-Center-Rack (Cabinet)
The Rosenberger-OSI Data-Center-Rack has been developed especially for FO patch distributors in Data Centers. In Data Centers the requirement for highest density becomes increasingly more important than
More informationThere is no upside to. down time
EXPANDED and PERFORATED Data and Specifications 30 Similar to Type 302 with excellent mechanical properties, resistance to many corrosive agents. Useful where sanitation and cleanliness are important.
More informationTELESCOPE Motorized Lighting Suspension
TELESCOPE Motorized Lighting Suspension Mod. 8400 FEATURES The De Sisti TELESCOPE is a single point suspension specifically designed to provide rigidity and stabilization of all moving parts. It can extend
More informationDryLin ZLW Belt Drive
Belt Drive +50º 0º DryLin toothed belt drives have been developed for the fast positioning of small loads. The linear units with toothed belt drive are corrosion resistant, light and compact, besides having
More informationROUNDO 3-Roll Plate Bending Machines Type PS
ROUNDO 3-Roll Plate Bending Machines Type PS Universal Machine used for all Plate Bending Double Pinch Design 1. Align the plate using the alignment grooves in the lower rolls or against the rear roll.
More informationLift- and transport truck HTW 50/100 Standard model
Lift- and transport truck HTW 50/100 Standard model The lift- and transport truck has a rugged, torsion-resistant frame structure, steel powder-coated (grey RAL 7035) with smoothly running, integrated
More information19 DYNAmax Free Standing Server C A B I N E T s
9 DYNAmax Free Standing Server C A B I N E T s 9 DYNAmax Free Standing Server Cabinets FAMILY W=600mm and W=800mm DYNAmax Series Free Standing Server Cabinets DYNAmax series Servering Enclosures, provide
More informationEZ-Steer Assisted Steering System
EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-54 Case IH CVX 1135 CVX 1145 CVX 1155 CVX 1170 CVX 1190 CVX 1195 CVX 135 CVX 145 CVX 155 CVX 175 CVX 195 New Holland TVT
More informationSpeed-Mat Rectangle Cutter
Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.
More informationElectroShade Skylight, Atrium and Monumental Shades
ElectroShade Skylight, Atrium and Monumental Shades Flat Horizontal Double Motor Soft Fold Top Down Gravity Drop Flat Triangular Double Motor Bottom Up Flat Top Down Gravity Drop Soft Fold Single Motor
More informationSTEEL-RITE II or III COMMERCIAL SECTIONAL DOOR Owner s Manual Supplement Model 52242 NOTICE TO USER
STEEL-RITE II or III COMMERCIAL SECTIONAL DOOR Owner s Manual Supplement Model 52242 NOTICE TO USER Thank you for purchasing the Steel-Rite II or III, model 52242 commercial sectional door from RITE-HITE
More informationTechnical Information
Technical Information This section of the catalogue provides technical information that will help specify, install and maintain Surelock McGill devices and components. The topics are listed below: Blast
More informationVXT. Open Cooling Towers. Open Cooling Towers. Product Detail VXT - B 1. Engineering Data... B2. Structural Support... B6
- B 1 Product Detail Engineering Data... B2 Structural Support... B6 Engineering Specifications... B9 - B 2 Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions &
More informationHighly flexible couplings
Construction and operation 8.03.00 Instructions for installation 8.03.00 Types of stress 8.04.00 Diagrams for static deformation of the coupling ring 8.05.00 Coupling size 8.07.00 Examples of combinations
More informationB.TECH. (AEROSPACE ENGINEERING) PROGRAMME (BTAE) Term-End Examination December, 2011 BAS-010 : MACHINE DESIGN
No. of Printed Pages : 7 BAS-01.0 B.TECH. (AEROSPACE ENGINEERING) PROGRAMME (BTAE) CV CA CV C:) O Term-End Examination December, 2011 BAS-010 : MACHINE DESIGN Time : 3 hours Maximum Marks : 70 Note : (1)
More informationSecure your IT equipment with confidence... secure with NetClosure
Secure your IT equipment with confidence... secure with NetClosure SERVER CABINETS NetClosure s REM Series Server Cabinet is the ultimate solution designed and engineered for demanding data center environments.
More informationHRA SULKY APPROVAL POLICY
HRA SULKY APPROVAL POLICY COMMENCEMENT DATE This policy comes into effect on 18 October 2010. PURPOSE The maintenance and improvement of the safety standards during harness racing has required Harness
More informationBUILD A TABLETOP LOOM
BUILD A TABLETOP LOOM From 1" x 2" stock (actual 3/4" x 1"1/2) cut: 4 pieces 15" long 4 pieces 5"1/2 long Use the above to make 2 frames for the front and back of the loom. From 1" x 4" stock (actual 3/4"
More informationCABLE SUPPORT SYSTEMS
CABLE SUPPORT SYSTEMS eaturing the CADDY CAT HP J-Hook System Why CADDY CAT HP? Why Choose CADDY CAT HP over tray? ast and Easy to Install Much faster installation compared to conventional cable or ladder
More informationCable ladder installation at S.C.M. Chemicals Limited s titanium dioxide Plant in Western Australia
Exel Composites Cable Support Systems offer engineers a structural product for solving many design and plant engineering problems, enabling long term reliable support of expensive and often critical cables.
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationVITOSOL r 200-T SP2A. VITOSOL 200-T Type SP2A
Technical Data Manual Model Nos. and pricing: see Price List Vacuum tube collector based on the heat pipe principle For the utilisation of solar energy VITOSOL r 200-T SP2A Product may not be exactly as
More informationK17.12 Door closers K17. Doors 01.09.2013
K17 Doors K17.12 01.09.2013 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com Contents 1. OPTIC door closer TS40(V) with scissor
More informationRollers. from the UK s largest roller manufacturer. Quality Performance Reliability
Rollers from the UK s largest roller manufacturer Quality Performance Reliability 42 Index Gravity Rollers Light to Medium Duty 4 Heavy Duty 5 Plastic Rollers 6 Stainless Steel Rollers 7 Grooved Rollers
More informationBelt and Roller Conveyor for boxes and containers
logiss srl 38068 Rovereto (TN) Italy Viale del Lavoro, 16/E (ZI) Tel. +39 0464 401121 Fax. +39 0464 423077 Mail technical@logiss.eu Web Belt and Roller Conveyor for boxes and containers A wide range of
More informationΑΡΧΙΤΕΚΤΟΝΙΚΑ ΣΥΣΤΗΜΑΤΑ ΑΛΟΥΜΙΝΙΟΥ ARCHITECTURAL ALUMINIUM SYSTEMS
ΑΡΧΙΤΕΚΤΟΝΙΚΑ ΣΥΣΤΗΜΑΤΑ ΑΛΟΥΜΙΝΙΟΥ ARCHITECTURAL ALUMINIUM SYSTEMS NORMAL SLIDING and SLIDING WITH THERMAL BREAK A L U M IN IU M S Y S T E M S 32 SERIES 32 SLIDING. : 9045 815 gr/m 475 mm -25-25 - FOR
More informationSOHOline and SOHO Slimline The SOHOline and SOHO Slimline offer a modular, sturdy and compact design
SOHOline and SOHO Slimline The SOHOline and SOHO Slimline offer a modular, sturdy and compact design Ideal installation for; Offices Branch Offices Schools Computer Aided Classes Government Offices Hotels
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More informationProfiles in stock Standard catalogue. Discover the possibilities with aluminium profiles from Sapa
Profiles in stock Standard catalogue Discover the possibilities with aluminium from Sapa You can create your own profile or you can choose from a wide selection of standard. Delivery: 1 2 weeks for standard
More informationPole Lathe and Shave Horse Design
Pole Lathe and Shave Horse Design These pictures and accompanying words are Copyright Michael Hughes February 2002. They are not to be re-produced, in part or whole, without permission from the author.
More information19 DYNAmax Free Standing Server C A B I N E T s
9 DYNAmax Free Standing Server C A B I N E T s 9 DYNAmax Free Standing Server Cabinets FAMILY W=mm and W=800mm DYNAmax Series Free Standing Server Cabinets DYNAmax series Servering Enclosures, provide
More informationTopSky DLG Installation Manual
TopSky DLG Installation Manual Attention: Because after the compound materials solidify, there will be ammonia iris on the surface, which affect the bonding strength afterwards. Please polish with sandpaper
More informationPOLE MOUNT SYSTEM-3 INSTALLATION
1 May 2014 POLE MOUNT SYSTEM-3 INSTALLATION The Pole Mount System-3 is an easy to install and flexible system designed to allow ONE SYSTEMS loudspeaker products to be mounted to pole structures. The only
More informationGeneral Safety. Always do a risk assessment.
recipitous.co.uk Access Equipment Call 020 8684 6999 Scaffold Towers Ladders & Steps Podiums Rigging Tube & Fittings New & Used Sales Hire Repair Manufacture The Skymaster Ladder is a 3 section combination
More informationInstallation Window Building In Details
Installation Window Building In Details INSTALLATION Photo courtesy of Rowe Aluminium DATE: NOVEMBER 2009 REPLACES: AUGUST 2003 INSTALLATION Installation Replaces: Scale: NOT TO SCALE Vantage snap-on couplers
More informationPUMP JACK SYSTEM AND ACCESSORIES
Pump Jack Model # 2200 A low cost, easy to operate, safe, portable scaffolding built of rugged steel. It's perfect for shingling, siding, sheathing, insulating, painting, building, roofing, home repair
More informationCLEAR-DIVISIONS CENTERFOLD
CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in
More informationCATALOGO PRODOTTI PORTONI INDUSTRIALI COIBENTATI
CATALOGO PRODOTTI PORTONI INDUSTRIALI COIBENTATI The Company Founded in 1973 by Mr Imes Tinti in association with his son Vanni Tinti. In 1999 the locksmith workshop became a modern industrial company
More informationLEADER IN CUTTING TECHNOLOGY
LEADER IN CUTTING TECHNOLOGY FOR OVER 2 YEARS REASONS WHY TRONEX IS THE BEST IN THE WORLD 1 2 SUPERIOR CUTTING PERFORMANCE Cut hundreds of thousands of times before dulling. Cut hundreds of thousands of
More informationFlamco Stainless steel mountings
S TA I N L E S S S T E E L M O U N T I N G S 9 Flamco Stainless steel mountings BRS-A BSF - SS RAIL R - SS GP - SS Edition 2007 / UK Stainless steel mountings Flamco offers the best attachment options
More informationReaction Torque Sensor
Force 1 1 N m up to 1 000 1 000 N m Type 9329A 9389A These easy to install piezoelectric reaction torque sensors are particularly suitable for measuring rapidly changing torques at non-rotating shafts.
More informationPOLE MOUNT SYSTEM EX-3 INSTALLATION
May 2014 POLE MOUNT SYSTEM EX-3 INSTALLATION The Pole Mount System EX-3 is an easy to install and flexible system designed to allow ONE SYSTEMS loudspeaker systems to be mounted to pole structures. The
More informationB098N USERS: MACHINE MANUFACTURERS DRAUGHTSMEN OPERATORS MAINTENANCE WORKERS ANY OTHERS
INSTRUCTION MANUAL TRAVELLING BEAM DEVICE MANUAL CODE B098N USERS: MACHINE MANUFACTURERS DRAUGHTSMEN OPERATORS MAINTENANCE WORKERS ANY OTHERS REV. DESCRIZIONE REDATTO/GESTITO APPROVATO COD. IDENT. PAGINE
More informationBasic Spring Motor Roller Shades
Comprehensive Roller Shade Installation Guide Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension
More informationDrive shaft, servicing
Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,
More informationFIBREGLASS LADDERS THE LADDER WITH THE BLUE TRIM
SUPERLITE STEP-LADDER WITH ALUMINIUM TREADS 1 700 700-06 SOLID TRIANGULAR BOTTOM GUSSET PINCH RESISTANT SPREADER BARS Ref. Bar Code No. of steps Weight 700-06 6005413007015 6 8.3kg 700-08 6005413007022
More information1300 MAXTRAK SPECIFICATION
CONE CRUSHER Crusher type: Liners: Standard concave: Lubrication: Adjustment: Control: Concave options: 1300 Automax Crusher. Manganese steel alloy mantle and concave. Medium Coarse. Pumped system having
More informationSECTION G2: CABLE PROCESSOR MODULE MAINTENANCE
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop
More informationOperator s Manual EVENTER 20 / 25 Series Lifts
Operator s Manual EVENTER 20 / 25 Series Lifts May 2013! Before operating this lift, read and understand this Operator s Manual. Become familiar with the potential hazards of this unit. Call SUMNER should
More informationGuidelines for Earthquake Bracing Residential Water Heaters
Guidelines for Earthquake Bracing Residential Water Heaters Department of General Services Division of the State Architect In accordance with the Health and Safety Code Section 19215, the Division of the
More informationHow To Work With Beads. By Rowan
R O W A N How To Work With Beads By Rowan HOW TO WORK WITH BEADS Adding beads to a knitted or crocheted design gives it a really special touch especially when the beads added are as stunning as those in
More informationIPR-02-64. Äspö Hard Rock Laboratory. International Progress Report. Temperature Buffer Test. Report for retaining plug and anchoring
International Progress Report IPR-02-64 Äspö Hard Rock Laboratory Temperature Buffer Test Report for retaining plug and anchoring Richard Bäck Äspö HRL September 2002 Svensk Kärnbränslehantering AB Swedish
More informationConstruction of a Fencing Mask
Academy of Historical Arts & HEMAC Construction of a Fencing Mask Author: Keith Farrell Version: 01 Date: 5th May 2012 Version and Copyright Information Version: 01 Date: 5th May 2012 Research: Copyright
More informationLED LEONARDO 120 W. LED Fresnel SPOTLIGHT White light, either Tungsten or Daylight balanced Correlated Color Temperature
LED LEONARDO 120 W LED Fresnel SPOTLIGHT White light, either Tungsten or Daylight balanced Correlated Color Temperature OVERVIEW The LED LEONARDO 120W is a highly efficient Fresnel lens spotlight using
More informationC O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S
C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S January 2009 Issue 6 Valu Guide Brackets The Ultimate in Adjustability and Cost Savings Valu Guide brackets are part of a family
More informationProfile rail guides LLR
Profile rail guides LLR Content The SKF brand now stands for more than ever before, and means more to you as a valued customer. While SKF maintains its leadership as the hallmark of quality bearings throughout
More informationCLEAR-DIVISIONS VARIOFOLD
CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the
More informationTECHNICAL MANUAL AWNINGS STELA, JASMINA, ISABELA, LAURA
TECHNICAL MANUAL AWNINGS STELA, JASMINA, ISABELA, LAURA EN MARKISE Contents - Awnings CE product marking 4 Jasmina awning without load-bearing profile 5 Basic technical specification 6 Stela awning with
More informationKnürr Miracel. Knürr Miracel. 19 Network and Server Rack Platform 1.12 to 1.22 1.11
Knürr Miracel 19 Network and Server Rack Platform 1.12 to 1.22 1.11 19" Server Rack: Knürr Miracel Strong points 1.13 Knürr Miracel ASP ASP/Server Rack 1.16 Knürr Miracel Server Rack 1.18 Knürr Miracel
More informationSheet metal operations - Bending and related processes
Sheet metal operations - Bending and related processes R. Chandramouli Associate Dean-Research SASTRA University, Thanjavur-613 401 Table of Contents 1.Quiz-Key... Error! Bookmark not defined. 1.Bending
More informationEZ-Steer Assisted Steering System
EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-21 Case IH Puma 165 Puma 180 Puma 195 Puma 210 New Holland T7030 T7040 T7050 T7060 Revision A June 2007 Part Number 53345-21-EU2
More information