OWNER S MANUAL IN-DASH LCD MONITOR/TV TUNER/ AM-FM RECEIVER/CD CHANGER CONTROLLER

Transcription

1 AUDIO SYSTEMS R BV - 00 OWNER S MANUAL IN-DASH LCD MONITOR/TV TUNER/ AM-FM RECEIVER/CD CHANGER CONTROLLER

2 R R R R Congratulations on your purchase of a Audio Systems Mobile Audio/Video System. This receiver/monitor has been built to deliver the highest quality video reproduction. We are sure you'll enjoy watching your favorite movies with this component as a part of your multimedia. For best results please consult a professional mobile electronics installer for application advice or troubleshooting. To guarantee top performance we recommend using The Link installation accessories such as RCA interconnects, power cables, and speaker wire. Thank you for choosing Audio Systems products for your mobile entertainment system. We can't change the world, but we can make it sound and look better. 1

3 INSTALLATION Notes: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop, like an emergency stop. If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance. 30 Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. INSTALLATION HARDWARE Bracket (A) (2 pcs) Bracket (B) (2 pcs) Double sided tape (2 pcs) Lever (2 pcs) Hexagonal Bolt (M6 x 12) (4 pcs) Tapping Screw (M x 12) (4 pcs) Mounting Bolt (M x ) (8 pcs) Mounting Bolt (M4 x ) (4 pcs) Strap (1 pcs) Tapping Screw (M x 2) (1 pcs) Nut (M) (1 pcs) Plain Washer (M) (1 pcs) Spring Washer (M) ( pcs) Spring Washer (M6) (4 pcs) 2

4 MOUNTING THE TUNER UNIT Step 1 Step Bracket (A). Tapping Screw with Washer (M x 12) 2. Mounting Bolt (M x ) 6. Spring Washer (M6) 3. Bracket (B) 7. Spring Washer (M) 4. Hexagonal Bolt with Washer (M6 x 12) 8. Double Sided Tape CAUTION: Most states and local governments have laws and/or ordinances prohibiting the viewing of TV or video while driving. This is for your safety. We advocate full compliance with all applicable laws with regards to mobile entertainment systems. Please consult your local authorities for more information. INSTALLING THE DISPLAY UNIT Before installing the display unit, please remove the backstrap screw and wiring harress. This unit can be properly installed either from front (convertional DIN Frontmount) or rear (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. DIN FRONT-MOUNT Installing the unit Dashboard 2. Mounting Bracket After inserting the holder into the dashboard, select the appropriate tabs according to the thickness of the dashboard material and bend them outwards to secure the bracket in place. (Fig. 1) 3. Display Unit 3

5 (Fig. 2) Removing the unit 1. Dashboard 2. Nut (M) 3. Spring Washer 4. Tapping Screw with Washer (M x 2). Screw 6. Plain Washer 7. Backstrap Be sure to use the backstrap to secure the back of the unit in place. The backstrap can be bent by hand to the desired angle. Note: The trim piece, backstrap, and mounting bracket are not used for REAR-MOUNT Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers upward and out to makes it possible to remove the unit. DIN REAR-MOUNT Installation using the screw holes on the both sides of the unit. 1 Fastening the unit to the factory radio mounting bracket Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws ( x mm) or screws (4 x mm), depending on the shape of the screw holes in the bracket. 2. Screw 3. Factory Radio Mounting Bracket 4. Dashboard or Console. Hook and Screw (Remove this part) Note: The frame, strap, and half-sleeve are not used for REAR-MOUNT. 4

6 HOW TO OPEN AND CLOSE THE SCREEN DISPLAY 1. Press release button then carefully pull the monitor out toward you. Release Button 2. Turning the display upward. 3. Adjust the viewing angle as shown. Adjustment should be made slowly using minimal force.

7 4. To close the unit, turn the display to the center position then fold it down. The monitor must be centered and folded down before the unit can be closed properly.. Push the panel in until is clicks into the locked position. 6

8 ELECTRICAL CONNECTION RADIO/TV MAIN UNIT (VIEW FROM REAR) RADIO/TV MAIN UNIT (VIEW FROM FRONT) TV DIVERSITY ANTENNA INPUT AV INPUT TV MONITOR AV1 RADIO CONTROL CDC INPUT AV2 CDC SET VIDEO AUDIO R AUDIO L A B REAR Rch SPK REAR Lch SPK FRONT Rch SPK FRONT Lch SPK VIOLET VIOLET/BLACK GREEN GREEN/BLACK GREY GREY/BLACK WHITE WHITE/BLACK BLUE/WHITE POWANT RED ACC YELLOW MEMORY CHOKE BLACK GROUND BOX GREY TV CONTROL GREY/BLACK TO CD CHANGER TV DIVERSITY ANTENNA INPUT RADIO ANTENNA INPUT Rch RED (BROWN) FRONT RCA CABLE Lch WHITE Rch RED (GREY) REAR RCA CABLE Lch WHITE (FOR RCA LINE VERSION ONLY) 7ohm RF WIRE (BLACK) VIDEO OUTPUT FROM VIDEO/AUDIO SOURCE TO SELECT CD CHANGER FORMAT BLACK CABLE BLACK PLUG BLACK/GREY CABLE GREY PLUG DISPLAY UNIT TO POWER SUPPLY RADIO CONTROL TV MONITOR CAUTION: If this monitor is mounted in a location that allows viewing from the driver s seat, the unit must be wired to prevent video operation (TV, DVD, VCP, video games, etc.) while the vehicle is being driven. 1. When the gray (TV control) wire is connected to the parking brake switch (in most late model vehicles) The BV-00 will not operate in the TV mode while the parking brake is engaged. 2. There are two operation formats for interfacing a CD Changer. Before completing the installation, connect the CD Changer to the BV-00, turn on the power, and select the CD mode. If the changer functions normally, the mode switch (located on the front of the tuner module) is in the correct position. If not, move the A-B switch to the other position. 7

9 OPERATION

10 GENERAL OPERATION ON/OFF Switch on the unit by pressing PWR button (1). When system is on, press it again to turn it off. FACEPLATE RELEASE Press REL button (2) to draw out the faceplate, push the panel to draw in. When the faceplate is drawn out, turn the faceplate upward and adjust TV display. SELECTING SOUND MODE Press SEL button (6) to move display through volume, bass, treble, balance and fader functions. Use (7) and (8) buttons to adjust the selected mode. When mode has not been adjusted for several seconds, display returns to previous display status (e.g. radio display or CDC display). VOL BAS TRE BAL FAD (Volume) (Bass) (Treble) (Balance) (Fader) Volume Adjust volume level using (7) and (8) buttons. Bass Press SEL button (6) for one time. Adjust bass level using (7) and (8) buttons. Treble Press SEL button (6) for two times. Adjust treble level using (7) and (8) buttons. Balance Press SEL button (6) for three times. Adjust sound balance between left and right speakers using (7) and (8) buttons. Fader Press SEL button (6) for four times. Adjust sound balance between front and rear speakers using (7) and (8) buttons. SELECTING PLAYING MODE When the screen display is drawn in, press MOD button (12) to select desired playing mode between radio and CDC. When the screen display is drawn out, the unit would automatically switch into TV mode. By pressing MOD button (12), you can select desired playing mode among TV, radio and CDC. CAUTION: The installation must be done in a way that prevents TV operation while driving. During this time you may choose between radio and CD (Changer) modes. MUTE Press MUT button (3) to cut down sound output, MUTE appears on display. Press it again to resume the previous volume level. SETTING THE CLOCK Press DSP button () to change the display into clock display. While the current time is appeared on the display, press it again to return to frequency showing. Time Setting - Set hours: Holding down DSP button () for several seconds, and the clock is blinking on the display, press button (14) to adjust the hour. 9

11 - Set minutes: Holding down DSP button () for several seconds, and the clock is blinking on the display, press button (13) to adjust the minutes. LIQUID CRYSTAL DISPLAY The LCD (4) can show the current state of the unit. RESET Reset button (29) must be activated with either a ball point pen or thin metal object. The reset button is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate. - Error symbol on the display. RADIO OPERATION SELECTING BAND Press BAND button (11) to change between three FM bands and two AM bands. Each band stores up to six preset stations. FM1 FM2 FM3 AM1 AM2 SELECTING STATION During radio mode, press MAN/SKP button (13) to increase frequency or (14) to decrease frequency by one step of channel spacing. Hold the button longer for fast tuning. The frequency is updated correspondingly on display. SELECTING MEMORY Press preset memory buttons (1) to preset stations at tuner mode. With this system, a total of 30 stations can be stored in the memory of six buttons. The stations might be FM1, FM2, FM3, AM1 and AM2 band. The operation is as below: - Store in Memory Press and hold desired memory location button for several seconds. The current listening station will be stored into the number button. - Retrieve a Preset Station Press any one of the buttons (1) to retrieve a station which had been stored in the memory in advance the chosen number is shown on display. AUTO MEMORY STORING & SCANNING - Auto Memory Scanning Check the stations stored in the preset memories. Press to retrieve automatically the current stations stored in six preset memories and it will display for several seconds. Press either the AS/PS button (16) again or anyone of the memory buttons to stop the scan operation. During the preset scan operation, the channel number flashes on the display for several seconds. Preset station scan continuously in the pre-selected band. 10

12 - Auto Memory Storing Seeks the six strongest stations in the pre-selected band automatically and stores the stations automatically in preset memories. Initially the tuner seeks and memories the stations in local mode until 6 stations are fully occupied. Otherwise, seeking is proceeded in distance mode. CDC OPERATION SELECTING TRACK During CDC mode, press MAN/SKP button (14) or (13) to move to the previous track or the next track. The track number shows on the display. SELECTING CD Press CD + button (17) to select next disc and CD button (18) to select previous disc. REPEAT THE SAME TRACK Press RPT button (19) to continuously repeat the same track on the current disc. Press it again to continuously repeat all tracks on the current disc. Press it the third time to stop repeating. PREVIEW ALL TRACKS Press SCN button (20) to play the first several seconds of each track on the current disc. Press it again to stop intro and listen to track. RANDOM PLAY Press RND button (21) to play all tracks on the current CD in random order. Press it again to cancel the mode. CD CHANGER SETTING MAIN UNIT (VIEW FROM FRONT) CDC SET A B Switch Button Reference the figure when used as a controller for a 6-disc CD changers, place the switch in the B position. For 10-disc CD changers (BOSS model CDC-3000) place the switch in the A position. TV OPERATION SELECTING RECEIVING MODE Press TV/AV button (22) to select among TVch/AV1/AV2. PICTURE ADJUSTMENT/PROGRAM SETTING/SYSTEM CONTROL In TV mode, press MENU button (23) to enter the main menu. And the menu includes three sub-menus: PICTURE MENU, TUNER MENU and SYSTEM MENU. 11

13 Press the button repeatedly or press CH + button (9) or CH button (10) to select the desired item then press CONTROL + button (24) or CONTROL button (2) to enter the corresponding sub-menu to set. - In PICTURE MENU, use CH + button (9) or CH button (10) to select picture mode upward or downward as follows: BRIGHT CONTRAST COLOR SHARP TINT Then use CONTROL + button (24) or CONTROL button (2) to adjust the selected item. Note: In PAL SYSTEM, there is no TINT item. - In TUNER MENU, use CH + button (9) or CH button (10) to select picture mode upward or downward as follows: POS SKIP BAND FINE AFT SEARCH ASM Then use CONTROL + button (24) or CONTROL button (2) to adjust the selected item. - In SYSTEM MENU, use CH + button (9) or CH button (10) to select picture mode upward or downward as follows: COLOR SOUND LANG. B/B CORING HALFTONE Then use CONTROL + button (24) or CONTROL button (2) to adjust the selected item. In AV mode, press MENU button (23), the screen will display PICTURE MENU and SYSTEM MENU but not TUNER MENU. And in SYSTEM MENU, there is no SOUND item. The setting method is the same with that in TV mode. Note: In the menus (except TUNER MENU), if you don t operate over 6 seconds, the screen display will disappear. SELECTING CHANNEL Press CH + button (9) or CH button (10) to choose channel upward or downward. PROGRAM SCANNING Press SCAN button (27), SCAN OFF will display on the lower left corner of the screen. Press it again, the screen will display SCAN ON, then it begins to scan 1. seconds of each channel in sequence. When it completes, the screen will display SCAN OFF. In the course of scanning, press SCAN button (27), SCAN OFF will also display on the screen and it stops on the TV channel just scanning. SCREEN DISPLAY Press DSP button (26), the screen will display the current status such as TVch/AV1/AV2, the COLOR SYSTEM and the SOUND SYSTEM on the right-top corner. In AV mode, there is no SOUND SYSTEM display. REMOTE SENSOR Point the remote control handset to the remote sensor (28). Press the function keys on the handset to control TV. 12

14 REMOTE CONTROL HANDSET CONTROL & FUNCTION KEYS 1. POWER = Press POWER to turn the unit ON or OFF 2. TV/AV = Switch between TV/AV1/AV = Numeric buttons, press to select the corresponding channel 4. -/-- = Digital selecting button, cooperatively used with numeric buttons. MUTE = Press to mute the sound. When release the button, the screen will display VOLUME XX for about 4 seconds, and this is the AUDIO level setting value of the TV unit. The users may not mind it, and that adjust the volume level by VOL + and VOL buttons. 6. SCAN = Scan 1. seconds of each channel 7. MENU = Display the main menu to adjust picture and set program and control system 8. / = In case of MENU mode, the buttons are used to select the sub-menus 9. / = In case of MENU mode, the buttons are used to adjust the selected item 10. VOL + = Increase the volume level 11. VOL = Decrease the volume level 12. PICT = Select picture mode. There are five modes: STANDARD, SHARP, BRIGHT, MEMORY and MILD. The MEMORY mode is user-defined mode and the others are preset mode. 13. RETURN = Switch between last viewed channel and this time viewed channel 14. CH + = Choose channel upward 1. CH = Choose channel downward 16. DSP = Press to display the channel number and SYSTEM status. In AV mode, there is no SOUND SYSTEM display 17. SORT = Program sorting button, cooperatively used with digital selecting button and numeric buttons 13

15 SPECIFICATION GENERAL Power Supply Voltage : DC 12 Volts, Negative Ground Maximum Power : 70 Watts x 4 Chassis Dimensions : 7 x 6.1 x (W) x 1 (D) x 0 (H) mm Weight : 4.4 KG 9.79 pounds Speaker Impedance : 4 Ohms Current Consumption : 10 Amperes (max.) T one Controls - Bass (at 100 Hz) : + / 10 db - Treble (at 10 KHz) : + / 10 db TV Monitor Screen Size Resolution TV Sensitivity :.0 TFT : 960 x 234 dots : 4 dbµv/pd in average RADIO FM Frequency Coverage : 87. to MHz Sensitivity (30 db S/N) : 6 µv Image Rejection : > 4 db Stereo Separation : > 2 db Frequency Coverage Sensitivity (20 db S/N) Image Rejection AM : 30 to 1710 KHz : 3 db : 4 db 14

16 R AUDIO SYSTEMS 341 Lunar Court Oxnard, CA T