97100 NAMUR 3/2, 5/2 & 5/3 way spool valves electromagnetic actuated, indirectly controlled flanged with NAMUR Interface, G 1/4, 1/4 NPT

Transcription

1 9700 NAMUR /, / & / way spool valves electromagnetic actuated, indirectly controlled flanged with NAMUR Interface, G /, / NPT For single and double operated actuators Crossover-free switching, switch-over function guaranteed even with small cross section air supply Valve switches at power failure into starting position (mechanical return spring, monostable design) Manual override with detent standard The solenoid valves are applicable in the protection class - Ex m for zones,,, (gases and dusts) ATEX cat.ii GD - Ex ia for zones,, (gases) ATEX cat.ii G, - Ex na, for zones, (gases and dusts) ATEX cat.ii GD Approval depends on magnetic system, see pages, and! Technical features Medium: Filtered, non-lubricated or dry compressed air Operation: Indirectly solenoid operated soft seal valves Operating pressure:... 8 bar Orifice: 6 mm Port size: : G /, / NPT and : G /8, /8-NPT NAMUR Interface with integrated exhaust air Flow direction: Fixed Mounting position: Optional Electrical connection: See solenoid table Fluid/Ambient temperature: C, Depending on solenoid system Air supply must be dry enough to avoid ice formation at temperatures below + C. Materials: Housing: Aluminium.06 anodized Pilot flange: Plastic (PBT) Seals: NBR (Perbunan) 9/ 00-c without notice, the specifications given in this document. 0 Norgren GmbH N/en..7.0

2 9700 NAMUR Technical data Standard version, / or / indirect acting valves (conversion instructions see page 6) Symbol Por size,, Actuation Operating pressure (bar) Flow (l/min) (kg) No. *) G / G /8 Flange Solenoid/spring , / NPT /8 NPT Flange Solenoid/spring , G / G /8 Flange Solenoid/solenoid , / NPT /8 NPT Flange Solenoid/solenoid , 9700 G / G /8 Flange Solenoid/solenoid mid position APB / NPT /8 NPT Flange Solenoid/solenoid mid position APB , , *) When ordering please indicate solenoid, voltage and current type (frequency). Valve function: APB = All Ports Blocked Solenoid operators for standard version 97xxx0 only Power consumption V d.c. 0 V a.c. (W) (VA) Rated current V d.c. 0 V a.c. (m A) (m A) Ex-Protection IP-Protection class (to EN 609) Ex-Protection (ATEX-Category) Temperature Ambient/Fluid,8 70 IP 6 (with connector) Connector DIN EN Form B *6) ( C) Electrical connection Circuit diagram (kg) Nr. Nr. 0, 00,6, 0 IP 6 (with connector) Steckverbinder DIN EN Form A *6) 0, 06 8 IIG IID,0 8 IIG IID,0 IIG IID,7 IIG IID Ex na IIC T Gc Ex tc IIIC T9 Dc IP 6 (with connector) Ex na IIC T Gc Ex tc IIIC T9 Dc IP 6 (with connector) Ex mb IIC T/T Gb Ex mb IIC T Gb Ex mb tb T0 C Db IP6 (with connector) Ex mb IIC T Gb Ex mb tb T9 C Db IP6 (with connector) With special connector DIN EN Form A With special connector DIN EN Form A,7 IP 66 (with connector) Connector Mx, DIN IEC *6) 0, 06 0, m cable 0, m cable 0, 06 0, 7 07 Standard voltages (±0%) V d.c., 0 V a.c. Further versions on request. *6) Connector is not scope of delivery, see table»accessories«datasheet ATEX IECEx FM 0x PTB 06 ATEX 0 N/de x PTB 0 ATEX 0 N/en x EC-Declaration of Conformity N/en 7..6 Solenoid with yellow LED N/en..7.0 without notice, the specifications given in this document. 0 Norgren GmbH 00-c 9/

3 9700 NAMUR Valves for minimal electrical power, incl. Ex i, / or / indirect acting valves (conversation intsructions see page 6) Symbol Port size,, Actuation Operating pressure (bar) Flow (l/min) (kg) No. *) G / G /8 Flange Solenoid/spring , / NPT /8 NPT Flange Solenoid/spring , 9700 G / G /8 Flange Solenoid/solenoid , 9700 / NPT /8 NPT Flange Solenoid/solenoid , 970 G / G /8 Flange Solenoid/solenoid mid position APB / NPT /8 NPT Flange Solenoid/solenoid mid position APB , ,0 970 *) When ordering please indicate solenoid, voltage and current type (frequency). Valve function: APB = All Ports Blocked Solenoid actuators Power consumption V d.c. 0 V a.c. (W) (VA) Rated current V d.c. 0 V a.c. (m A) (m A) Ex-Protection IP-Protection class (to EN 609) Ex-Protection (ATEX-Category) Temperature Ambient/Fluid,8 70 IP 6 (with connector) Connector DIN EN Form B *6) ( C) Electrical connection Circuit diagram (kg) Nr. Nr. 0, 00 0,7,0 *) 9 IP 6 (with connector) Connector DIN EN Form A *6) 0, 0 8 IIG IID Ex na IIC T Gc Ex tc IIIC T9 Dc IP6 (with connector With special connector DIN EN Form A 0, 06,0 IIG IID,7 IIG IID Ex mb IIC T/T Gb Ex mb IIC T Gb Ex mb tb T0 C Db IP6 (with connector) Ex mb IIC T Gb Ex mb tb T9 C Db IP6 (with connector),7 IP 66 (with connector) Connector Mx, DIN IEC *6) m cable 0, m cable 0, 06 Solenoid with yellow LED Standard voltages (±0%) V d.c., 0 V a.c. Further versions on request. *) Valves can be operated with DC only. For 0V AC application please use 06V DC coil together with recifier plug: model 0660 *6) Connector is not scope of delivery, see table»accessories«0, 7 07 Datasheet ATEX IECEx FM 0x PTB 06 ATEX 0 N/de x PTB 0 ATEX 0 N/en x EC-Declaration of Conformity N/en / 00-c N/en..7.0 without notice, the specifications given in this document. 0 Norgren GmbH

4 9700 NAMUR For intrinsically safe circuits, Protection class Ex ia IIC T6/T Ga (cat. II G) Nominal resistance RN coil (Ω) Required switching current min. (ma) Resistance RW 0 coil (Ω) Required voltage at terminal RW 0 (V) Temperature Ambient/ Fluid( C) 7 7,8 T T Electrical connection Connector DIN EN Form A *6) IP6 (with connector) (kg) No. Circuit diagram No. 0, 09 When selecting an intrinsically safe power supply, the permissible maximum values according to the Certificate of Conformity should be taken in account. On the other hand, the low effective inductivity and capacity can be ignored. *6) Connector not supplied, required connector: model 0707 Datasheet ATEX IECEx FM 09 PTB 0 ATEX CSA-LR 090- N/en 7..0 N/en..7.0 without notice, the specifications given in this document. 0 Norgren GmbH 00-c 9/

5 9700 NAMUR Options selector Function / way valve, spring return 0 (/ way valve by swapping enclosed adaptor plate) / way impuls valve (/ way valve by swapping enclosed adaptor plate) / way valve, APB (all ports blocked) Port size G / 0 / NPT Voltage V d.c V a.c. 0. Solenoids see table Manual override Push and lock 0 Push and lock, Ex i version only Accessories Connector DIN EN Connector M x M x Silencer Flange plate Yoke Page 8 Page 8 Page Form A 00 (without cable) 006 (90, without cable) C/S (/8 NPT) (NAMUR single connection plate) Form A (with rectifier) 007 ( m cable) 008 (90, m cable length) M/S (G /8) 0679 (NAMUR-rip use in combination with 06790, Alu) Form B 00 ( m cable) 00 (90, m cable length) s Valves 0 0 G / G /8 0,, 6, 8, 0, 7, 7, M, 9, G / G / M 9.. O ring ø 6 x mm in scope with delivery Hole ( mm deep) coding stud / 00-c N/en..7.0 without notice, the specifications given in this document. 0 Norgren GmbH

6 9700 NAMUR s Solenoid operators , 6 Ø9 Ø9 9 8, 0 9,, 9, 9, Mx ~8 Ø9 Electrical connection M x 9 7 9, 8,, Pin Signal Cable + UB brown Out (PNP) / analogue to 0 ma white 0 Volt blue Out (PNP) black M6 X, 0 8 9,, M6 X, 0 8 Ø9 Connector x 90 turnable N/en without notice, the specifications given in this document. 0 Norgren GmbH 00-c 9/

7 9700 NAMUR Circuit diagrams 7 NAMUR hole pattern (driving side) M Port (A) Coding stud threaded M & M6 (0 deep) Port (R) NAMUR quick exhaust module for a better kv-value by exhaust see data sheet..80 NAMUR interlinking plates in redundancy design for»safety exhausting«and»safety ventilating«see data sheet..80 Conversion instructions of / into / way function / way function (original mode of supply) / way function / / / resp. / way function according to version by swapping or turning enclosed adaptor plates. Make sure Marker and Arrow do match as shown on above drawing. Original mode of supply: / function. 6 Arrow 7 Marker 9/ 00-c N/en without notice, the specifications given in this document. 0 Norgren GmbH

8 9700 NAMUR Single connection plate : NAMUR slot : , M (x),, 6 6, G / 9 9,, ø 9, 9 ø, G /, ø 9 ø, 7 Yoke : x 0 M 0 Silencer : M/S, C/S 6, ø, /8 Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under Technical features. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult NORGREN. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. N/en without notice, the specifications given in this document. 0 Norgren GmbH 00-c 9/