WL50S High-Intensity Work Spot Light

Transcription

1 Datasheet General-purpose LED work lighting For the latest technical information about this product, including specifications, dimensions, and wiring, see anner Engineering. Three lens options, depending on model, to vary spot size Illuminates a large area with an even pattern of light and no shadows 2 to 0V dc operation abled and quick-disconnect models available 50 mm diameter with flat profile and 0 mm mounting base Rugged sealed housing rated to IP69K WRNING: Not To e Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. failure or malfunction can cause either an energized or de-energized output condition. Models Model LED olor Lumens Lux Lens ngle onnection 0.5 m m WL50SWL5Q White, K WL50SRL5Q Red, nm WL50SGL5Q Green, nm WL50SWLQ White, K WL50SRLQ Red, nm WL50SGLQ Green, nm WL50SWL20Q White, K WL50SRL20Q Red, nm WL50SGL20Q Green, nm ±5 (smaller, more focused ± (larger ±20 (largest 5 pin Euro integral QD connector (use with a 4-wire mating cordset; only 2 wires used for connection) Integral QD models only are listed. For integral 2 m (6.5') PV cable, omit suffix Q from model number (example, WL50SWL5). model with a QD requires a mating cordset (see 4-Pin Euro-Style ordsets on page ).

2 Specifications Supply Voltage and urrent Operating voltage: 2 to 0V dc urrent draw: 400 m max. Supply Protection ircuitry Protected against reverse polarity and transient voltages Light Source Three high-intensity LEDs; see models table for color temperature or wavelengths Useful Life When operating within specifications, output will decrease less than 0% after 50,000 hours. onstruction lack anodized aluminum housing; polycarbonate window; nickel-plated QD connector or PV-jacketed cable; black zinc-plated steel mounting nut Mounting: 0x.5 mm thread base mount onnections Integral 5-pin M2/Euro style QD or 2 m (6.5 ft) integral cable, depending on model; 4-pin connecting cordset required for QD models; only 2 wires used Environmental Rating IE IP67, IP69K per DIN NOTE: Do not spray the cable with a high-pressure sprayer or cable damage will result. Operating onditions 20 to +50 ( 4 F to +22 F) 95% maximum relative humidity (non-condensing) Vibration and Mechanical Shock ll models meet Mil. Std. 202F requirements method 20 (vibration: 0 to 60 Hz max., double amplitude 0.06", maximum acceleration 0G). lso meets IE ; 0G ms duration, half sine wave. Storage Temperature 40 to +70 ( 40 F to +58 F) ertifications eam Patterns

3 Dimensions Wiring Female Wiring Key: = rown = lue 2-0V dc Male 4-Pin Euro-Style ordsets 4-Pin Threaded M2/Euro-Style ordsets Model Length Style Dimensions Pinout MQD-406 MQD- MQD-40 MQD-0.8 m (6 ft) 4.57 m (5 ft) 9.4 m (0 ft) 5.2 m (50 ft) Straight 44 Typ. M2 x ø = rown 2 = White = lue 4 = lack

4 4-Pin Threaded M2/Euro-Style ordsets Model Length Style Dimensions Pinout MQD-406R MQD-R.8 m (6 ft) 4.57 m (5 ft) 2 Typ. [.26"] MQD-40R MQD-0R 9.4 m (0 ft) 5.2 m (50 ft) Right-ngle 0 Typ. [.8"] M2 x ø 4.5 [0.57"] Mounting rackets ll measurements are in mm SM0 Right-angle bracket with curved slot for versatile orientation learance for M6 (¼ in) hardware Mounting hole for 0 mm 2-ga. stainless steel Hole center spacing: to =40 Hole size: =ø 6., = 27. x 6., =ø SM0S Swivel bracket with 0 mm mounting hole for lack reinforced thermoplastic polyester Stainless steel mounting and swivel locking hardware included Hole center spacing: =ø 50.8 Hole size: =ø 7.0, =ø SM0F Swivel bracket with tilt and pan movement for precise adjustment Mounting hole for 0 mm 2-ga. 04 stainless steel Easy mounting to extrude rail T-slot Metric and inch size bolt available olt thread: SM0F, = /8-6 x 2 in; SM0FM0, = M0 -.5 x 50 Hole size: = ø 0. SMMS0R Right-angle SMMS series bracket 0 mm hole for mounting s rticulation slots for 90 + rotation 2-ga. (2.6 mm) cold-rolled steel Hole center spacing: =26.0, to =.0 Hole size: =26.8 x 7.0, =ø 6.5, =ø SM0MM 2-ga. stainless steel bracket with curved mounting slots for versatile orientation learance for M6 (¼ in) hardware Mounting hole for 0 mm SMMS0P Flat SMMS series bracket 0 mm hole for mounting s rticulation slots for 90 + rotation 2-ga. 00 series stainless steel 9 Hole center spacing: = 5, to = 25.4 Hole size: = 42.6 x 7, = ø 6.4, = ø 0. Hole center spacing: =26.0, to =.0 Hole size: =26.8 x 7.0, =ø 6.5, =ø.0

5 anner Engineering orp Limited Warranty anner Engineering orp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. anner Engineering orp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the anner product. THIS LIMITED WRRNTY IS EXLUSIVE ND IN LIEU OF LL OTHER WRRNTIES WHETHER EXPRESS OR IMPLIED (INLUDING, WITHOUT LIMITTION, NY WRRNTY OF MERHNTILITY OR FITNESS FOR PRTIULR PURPOSE), ND WHETHER RISING UNDER OURSE OF PERFORMNE, OURSE OF DELING OR TRDE USGE. This Warranty is exclusive and limited to repair or, at the discretion of anner Engineering orp., replacement. IN NO EVENT SHLL NNER ENGINEERING ORP. E LILE TO UYER OR NY OTHER PERSON OR ENTITY FOR NY EXTR OSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR NY INIDENTL, ONSEQUENTIL OR SPEIL DMGES RESULTING FROM NY PRODUT DEFET OR FROM THE USE OR INILITY TO USE THE PRODUT, WHETHER RISING IN ONTRT OR WRRNTY, STTUTE, TORT, STRIT LIILITY, NEGLIGENE, OR OTHERWISE. anner Engineering orp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by anner Engineering orp.