Hướng dẫn cấu hình Wireless EnGenius WDS

Transcription

1 Hướng dẫn cấu hình Wireless EnGenius WDS Hướng dẫn cấu hình Access Point Hướng dẫn cấu hình Client Bridge Hướng dẫn cấu hình WDS Bridge Hướng dẫn cấu hình Repeater Hướng dẫn cấu hình WDS Access Point Hướng dẫn cấu hình Client Router Hướng dẫn cấu hình WISP Client Router Mode Wireless Internet Service Proviver CB Hướng dẫn cấu hình Access Point EnGenius Wireless products see EnGenius PC or Notebook, Configure you PC/Notebook network interface to IP address and subnet mask to Open your browser and type in into URL bar, (Check instruction Select [Access Point] and click on [Apply]. Try to use your notebook to access Hướng dẫn cấu hình Client Bridge Two EnGenius Wireless products see EnGenius PC or Notebook, Configure you PC/Notebook network interface to IP address and subnet mask to Configuratiion the first device as AP (Access Point) Configuration of second device as CB (Client Bridge) Open your browser and type in into URL bar, (Check instruction Select [Client Bridge] and click on [Apply].

2 Select on left Menu [Wireless Network] Select [Site Survey] and click on [Apply]. Select which [SSID] you want to connect. in case that you have Wireless security please type password of your main or First AP 10. Try to ping across you CB to the first AP if you get response that mean you have finished 1 You can check status Page see another example of Client Bridge (CB) Hướng dẫn cấu hình WDS Bridge Two EnGenius Wireless products see EnGenius Configuratiion the first device as (WDS Bridge) Configuratiion the second device as (WDS Bridge) Exchange Mac Address Same channel PC or Notebook, Configure you PC/Notebook network interface to IP address and subnet mask to Configuration of second device as CB (Client Bridge) Open your browser and type in into URL bar, (Check instruction Select [WDS Bridge] and click on [Apply]. Select on left Menu [WDS Link Setting] 10. Enter the MAC addresses of the other APs which you would like to link with.

3 1 in case that you have Wireless security please type password of your main or First AP 1 click [Apply] for saving 1 Repeat from Step 7 for second Wireless device 1 Try to ping across your WDS bridge device to the first AP if you get response that mean you have finished see another example of WDS Bridge system Hướng dẫn cấu hình Repeater 2-3 EnGenius Wireless products see EnGenius depend how wide is the area Configuratiion the first device as AP How to configuration AP Configuratiion the second device as Repeater PC or Notebook, Configure you PC/Notebook network interface to IP address and subnet mask to Configuration of second device as Repeater Open your browser and type in into URL bar, (Check instruction default IP to access device) Select [Repeater] and click on [Apply]. Select on left Menu [Wireless Network] Select [Site Survey] and click on [Apply]. Select which [SSID] you want to connect. 10. in case that you have Wireless security please type password of your main or First AP 1 Try to ping across you CB to the first AP if you get response that mean you have finished 1 You can check status Page see another example of Repeater system Hướng dẫn cấu hình WDS Access Point

4 Two EnGenius Wireless products see EnGenius Configuratiion the first device as AP How to configuration AP Configuratiion the second device as AP too Exchange Mac Address Same channel PC or Notebook, Configure you PC/Notebook network interface to IP address and subnet mask to Configuration WDS Open your browser and type in into URL bar, (Check instruction Select [Access Point] and click on [Apply]. Select on left Menu [WDS Link Setting] 10. Enter the MAC addresses of the other APs which you would like to link with. 1 in case that you have Wireless security please type password of your main or First AP 1 click [Apply] for saving 1 Repeat from Step 7 for second Wireless device 1 Try to ping across your first AP and second AP if you get response that mean you have finished see another example of WDS, all client near by range can access the device Hướng dẫn cấu hình Client Router EnGenius Wireless products see EnGenius Configuratiion the device as AP Router PC or Notebook, Configure you PC/Notebook network interface to IP address and subnet mask to

5 This is assume that you have finish Configuration AP, Open your browser and type in into URL bar, (Check instruction Select [AP Router] and click on [Apply]. Select [WAN setting] and click on [Apply]. Normally the defaul will be DHCP but you can set your IP network / subnet / DNS... IP of router should be different from main network see example Try to use your notebook to access after connected you will get DHCP number from you AP router see another example of AP router, all client near by range can access the wireless but get different IP from main network Hướng dẫn cấu hình WISP Client Router Mode Wireless Internet Service Proviver CB EnGenius Wireless products see EnGenius Configuratiion the device as AP How to configuration AP or you may have WISP subsciber near by The configuration will be in second device or client and must be configuration on WAN Setting PC or Notebook, Configure you PC/Notebook network interface to IP address and subnet mask to This is assume that you have finish Configuration AP, Open your browser and type in into URL bar, (Check instruction Select [Client Router] and click on [Apply]. Select [WAN setting] Normally the defaul will be DHCP but you can set your IP network / subnet / DNS... IP of router should be different from main network see example

6 10. Try to use your notebook to access after connected you will get DHCP number from you AP router see another example of AP router, all client near by range can access the wireless but get different IP from main network IT Support Tanduylinh.com