Actuators for radiator valves

Transcription

1 ctuators for radiator valves with 2.5 mm nominal stroke SS3... SS SS... without auxiliary switch SS... with auxiliary switch Electro-mechanical actuators for radiator valves. Nominal stroke range 2.5 to 5 mm utomatic stroke recognition 3-position or DC 0 0 V control signal C 24 V or C 230 V operating voltage Direct assembly with union nut (no tools required) Can be operated manually Optional auxiliary switch C 250 V / (0.5), with adjustable switching point % Plug-in cable for supply voltage and control signal Parallel connection of multiple actuators possible With position indicator Use For use in heating systems in conjunction with radiator valves from Siemens or from other manufacturers. Functions The DC V control signal or the 3-position control voltage generates a stroke in the actuator which is transmitted to the valve stem. SS3... / SS8... (3-position control) (DC V control signal) Voltage at Y: Valve opens Voltage at Y2: Valve closes No voltage at Y and Y2: Valve remains in current position. The valve opens in proportion to the voltage at Y. t 0 V, the valve is closed. Type summary The basic types are supplied with a.5 metre cable, but actuators may also be ordered without a cable (type codes ending in.../00). long connecting cable (4.5 m, see ccessories ) can be ordered for these. The SS3... and SS8... actuators are also available with auxiliary switches. uxiliary switches ctuator types SS3... and SS8... have a built-in auxiliary switch. The switch cannot be fitted later. HVC Products /5

2 Type summary (continued) ccessories Operating Running time Control signal Cable length Built-in Type voltage at 50 Hz aux. switch SS3 C 230 V 50 s 3-position.5 m No SS8 C 24 V 50 s 3-position.5 m No SS6 C 24 V 34 s DC V.5 m No SS3. C 230 V 50 s 3-position.5 m Yes SS8. C 24 V 50 s 3-position.5 m Yes SS3/00 C 230 V 50 s 3-position No cable No SS8/00 C 24 V 50 s 3-position No cable No SS6/00 C 24 V 34 s DC V No cable No SS3./00 C 230 V 50 s 3-position No cable Yes SS8./00 C 24 V 50 s 3-position No cable Yes SY3L45 Connecting cable C 230 V, 3-position Length 4.5 m SY6L45 Connecting cable C 24 V, DC V Length 4.5 m SY8L45 Connecting cable C 24 V, 3- position Length 4.5 m SY98 Retaining screw for connector dapters for third-party valves V5 V52 V53 V54 V55 V56 dapter for Beulco dapter for Comap dapter for Danfoss R-N dapter for Danfoss RVL dapter for Danfoss RV dapter for Giacomini V57 dapter for Herz V59 dapter for Vaillant V60 dapter for T RVT V6 dapter for Markaryd V00-MLG dapter for Siemens Radiagyr valves Ordering When placing an order please state the quantity, product name and type code. Items are supplied individually packed. Example: 2 actuators, type SS8/00 and 2 connecting cables, type SY8L45 Compatibility The actuators are suitable for use with the following Siemens valves: Valve type kvs [m 3 /h] Nom. pressure [bar] Sheet 2-port valves VD0, VD5, VD25 VD20, VD25, VD ngle valves VE0, VE5, VE25 VE20, VE25, VE Reverse angle valves VU Valves from other manufacturers For trouble-free operation in conjunction with the SS actuators, third-party valves must comply with the following specification : F x 9087 y Threaded connection with union nut M30x.5 ctuator power in range F = N Dimension x, valve closed: x > 9 mm Dimension y, valve open: y 4.5 mm M30 x.5 B To date, the following valves have been tested: Heimeier (standard types), Honeywell, MNG, Finimetall, T (Type TRV400), Cazzaniga, formerly SCS (Types 2T.../). CN4893E/ Siemens Building Technologies 2/5 HVC Products

3 3 mm Mechanical design Features: The actuator and valve are supplied separately. They are assembled with a union nut, requiring no tools or adjustments. In the case of actuators with auxiliary switches, the switch is connected to terminals and must be wired separately. Plastic housing Stall-proof gear unit, no maintenance required Plug-in connecting cable, length.5 m Non-interchangeable C 24 V and C 230 V sockets Manual adjustment with 3 mm llen key Reduced current consumption in stop positions Force-dependent switch-off in the event of overload, and in stroke end-positions. Up to 6 SS3 or SS8, or up to 0 SS6 actuators may be operated in parallel. 807 Engineering notes Note the admissible temperatures (see sections on Use and Technical data ). The connecting cable will not be damaged by contact with the valve body as long as the valve body temperature does not exceed 80 C. Mounting Orientation Mounting instructions are printed on the packaging Permissible NOT permissible Commissioning When commissioning, check the wiring and the functioning of the actuator and auxiliary switch, if fitted. Spindle extended (movement from Mark 0 to ): Valve opens. Spindle retracted (movement from Mark to 0): Valve closes. Caution The calibrates itself (calibration stroke) during commissioning. Correct functioning cannot be guaranteed if the SS is operated without a valve. Operation The actuators can be driven manually to any position between 0 and with a 3 mm llen key. control signal from the controller, however, will take priority over any manual position. Note To hold the actuator in the manually set position, the connecting cable must be unplugged. 3 mm Manual adjustment with llen key B mm B Position indicator at Mark 0 = CLOSED Position indicator at Mark = OPEN HVC Products 3/5

4 Maintenance When servicing the actuator note the following: Switch off the operating voltage. Where applicable, disconnect electrical connections from the terminals. The valve must be mounted in accordance with instructions before commissioning the actuator. Technical data Supply voltage SS3... SS8... Operating voltage C 230 V ±5 % C 24 V ± 20 % C 24 V ± 20 % DC 24 V ± 25 % Frequency 50 / 60 Hz 50 / 60 Hz 50 / 60 Hz Max. power consumption 6 V 0.8 V 2.0 V Quick-acting fuse protection for incoming cable Control uxiliary switch (optional) pplies to all types General ambient conditions Control signal 3-position 3- position DC V Input impedance for DC V > 00 kohm Position accuracy for DC V < 2 % of nominal stroke Max. no. of parallel connected actuators Switch type SPDT SPDT Switching point adjustable from % % Switching capacity C 250 V, resistive, 0.5 inductive Running time for 2.5 mm stroke 50 s 50 s 34 s Nominal stroke 2.5 mm (5.5 mm max.) Nominal force 00 N 5 / + 60 % Connecting cable (actuator) 3-core, length.5 m or 4.5 m Weight without / with auxiliary switch 0.3 kg / 0.4 kg Operation to IEC Class 3K3 : C and %rh Transport to IEC Class 2K3 : C and max. 95 %rh Storage to IEC72-3- Class K3 : C and %rh dmissible temperature of medium (in valve) C Safety With C 24 V operating voltage With C 230 V operating voltage Housing protection standard to EN60730 section 2.7 : Protection class III to EN60730 section 2.7 : Protection class II IP40 CE marking Meets the requirements for CE marking in accordance with EMC directive Low Voltage directive 89/336/EEC 73/23/EEC Connecting cable SS3... Y 6 Black 8022 Control voltage, OPEN (C 230 V) N 4 Blue Neutral (neutral conductor) Y2 7 White Control voltage, CLOSE (C 230 V) SS8... Y 6 Purple 8023 Control voltage, OPEN (C 24 V) G Red Phase (C 24 V) Y2 7 Orange Control voltage, CLOSE (C 24 V) G0 2 Black 8024 System neutral G Y 8 Red Grey Phase (C 24 V) Control signal DC V CN4893E/ Siemens Building Technologies 4/5 HVC Products

5 SS3. and SS8. : Terminals for auxiliary switches Q4 Q2 Q 8025 Do not exceed the max. loads for the SPDT contacts : Max. C 250 V Max. resistive Max. 0.5 inductive Q Q2 closed and Q Q4 open: > Valve > 0 % OPEN. djustable switching point. Q Q2 open and Q Q4 closed: > Valve 0 % = CLOSED The switching point can be adjusted by turning the switching cam with a screwdriver (instructions enclosed with packaging). Dimensions ll dimensions in mm Without auxiliary switches SS3... SS With auxiliary switches SS3... SS Siemens Building Technologies Ltd. HVC Products 5/5