ONR CEN/TR DRAFT ICS

Transcription

1 ICS DRAFT ONR CEN/TR Guidelines on implementing EN :2009+A1:2011, Execution of steel structures and aluminium structures Part 1: Requirements for conformity assessment of structural components Leitfaden für die Umsetzung von EN :2009+A1:2011, Ausführung von Stahlbetonwerken und Aluminiumtragwerken Teil 1: Konformitãtsnachweisverfahren für tragende Bauteile Note: Because of possible comments, the final version of this ONR can differ from the present Draft. Please send your comments (in writing) by to Austrian Standards Institute. Edition:

2 DRAFT ONR CEN/TR 17052: Explanations concerning Draft The present Draft Technical Report CEN/TR 17052, falling within the scope of Committee 013 Steel-, composite- and aluminium-structures, has been submitted to CEN members for voting. In case of a positive result of the voting as required by CEN/CENELEC regulations, this Draft will be published as CEN/TR. Like all member organizations of CEN, Austrian Standards Institute is basically obliged to make available European Technical Reports in Austria in an appropriate manner. Until a possible subsequent transformation of a CEN/TR into an EN, conflicting national standards may remain in force. Austrian Standards Institute herewith submits this Draft of a Technical Report as Draft ONR to public enquiry and information. Since a German translation is not yet available, the English version of prcen/tr is submitted to public enquiry and information, in order to observe the deadline fixed by CEN. Comments on this Draft Please find below some practical instructions intended to offer you and the responsible committee assistance for the processing of comments and proposals for modification: Form Structure Language Script/Format Dispatch Aspects concerning patent law For your comments/proposals for change, please use the relevant form available from Internet. Download under or use the Draft Standard Portal Please use a new line for each comment. This facilitates the attribution of the comments received to the different clauses and chapters of the respective Draft. Please formulate technical comments on European Standards if possible in English, since English is the common working language of the most European standardizing bodies. Editorial and/or linguistic proposals for change/improvement of German versions of European Standards shall (certainly) be submitted in German. Please use the script Arial with 9 pt font size. Please do not change the formats. Please send your comments by to the responsible Committee Manager (k.stumwoehrer-gleich@austrian-standards.at) The recipients of this Draft ÖNORM are requested to add information on any patent rights known to their comments and to provide supporting documentation, if available. 2

3 TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHER BERICHT FINAL DRAFT FprCEN/TR August 2016 ICS English Version Guidelines on implementing EN :2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components Leitfaden für die Umsetzung von EN :2009+A1:2011, Ausführung von Stahlbetonwerken und Aluminiumtragwerken - Teil 1: Konformitãtsnachweisverfahren für tragende Bauteile This draft Technical Report is submitted to CEN members for Vote. It has been drawn up by the Technical Committee CEN/TC 135. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation. Warning : This document is not a Technical Report. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a Technical Report. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprCEN/TR 17052:2016 E

4 FprCEN/TR 17052:2016 (E) ONR DRAFT Contents Page European foreword... 3 Introduction Scope References Terms and definitions Conditions necessary for construction products to be covered by the scope of EN Clarification General Condition 1 The product fulfils the requirements of EN or EN Condition 2 The product is a structural construction product within the meaning of the Construction Products Regulation (EU) 305/ Condition 2a - The product is intended to be incorporated in a permanent manner in construction works Condition 2b - The product has a structural function in relation to the construction work Condition 3 The product is not covered by another European technical specification General Construction products covered by another harmonized standard Construction products covered by an ETA Annex A (informative) Products covered by EN Annex B (informative) Products not covered by EN

5 ONR DRAFT FprCEN/TR 17052:2016 (E) European foreword This document (FprCEN/TR 17052:2016) has been prepared by Technical Committee CEN/TC 135 Execution of steel structures and aluminium structures, the secretariat of which is held by SN. This document is currently submitted to the Vote on TR. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. 3

6 FprCEN/TR 17052:2016 (E) ONR DRAFT Introduction The scope of the standard EN :2009+A1:2011 Execution of steel structures and aluminium structures: Part 1: Requirements for conformity assessment of structural components is very broad and prompted the European Commission to publish on their website under the category Frequently Asked Questions (FAQ) on the Constructions Products Regulation a set of conditions for identifying when a steel or aluminium product falls within its scope and an indicative, non-exhaustive list of products that are not covered by the scope of EN :2009+A1:2011. This Technical Report aims to clarify in addition to the answers given on the European Commission s FAQ website the scope of EN :2009+A1:

7 ONR DRAFT FprCEN/TR 17052:2016 (E) 1 Scope The scope of EN :2009+A1:2011 states that the standard covers structural components and kits which are referred to as structural construction products in this document. This Technical Report gives information that clarifies when a structural construction product is covered by the scope of EN :2009+A1:2011 and lists examples of products covered and not covered. 2 References The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN :2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components EN :2008+A1:2011, Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures EN :2008, Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 harmonized standard for construction products hen standard adopted by one of the European standardisation bodies listed in Annex I to Directive 98/34/EC, on the basis of a request issued by the Commission, in accordance with Article 6 of that Directive, and which has been cited in the Official Journal of the European Union (OJEU) as a harmonized standard under the Construction Products Regulation (EU) 305/2011/EC 3.2 European Assessment Document EAD document on the basis of the EU Construction Products Regulation EU 305/2011 adopted by the organisation of Technical Assessment Bodies for the purposes of issuing European Technical Assessments 3.3 European Technical Assessment ETA documented assessment of the performance of a construction product in relation to its essential characteristics, in accordance with the respective European Assessment Document 5