LAV B Page 1 of 9 Engine Parts List #1

Transcription

1 LAV B Page 1 of 9 Engine Parts List #1

2 LAV B Page 2 of 9 Engine Parts List # B Cylinder (Incl. 2, 8, 9 & 20) (2-5/8" Bore) Pin, Dowel Washer, Flat Rod, Governor A Lever, Governor Clamp, Governor lever (Clamp is positioned towardsspark plug end on and latermodels. It is positioned opposite spark plugend on earlier models.) Screw, 8-32 x 5/16" Spring, Governor Seal, Oil A Crankshaft Piston, Pin & Ring Set (Std.) (2-5/8" Bore) Piston, Pin & Ring Set (.010" OS) Piston, Pin & Ring Set (.020" OS) B Piston & Pin Ass'y.(Std.)(Incl. 43)(2-5/8") B Piston & Pin Ass'y. (.010" OS) (Incl. 43) B Piston & Pin Ass'y. (.020" OS) (Incl. 43) Ring Set (Std.) (2-5/8" Bore) Ring Set (.010" OS) Ring Set (.020" OS) Ring, Piston pin retaining Rod Assy., Connecting (Incl. 18) 46A Plate, Lock (Do not use with 32610A locking type screw) Connecting Rod Bolt (Early Production ) A Bolt, Connecting rod 48A Lifter, Intake valve Lifter, Exhaust valve Camshaft (MCR) Pump Assy., Oil Extension, Blower housing Screw, Torx T-30, 1/4-20 x 1/2" * Gasket, Mounting flange D Flange Ass'y. (Incl. 58, 72, 75, 80 & 306) Plug, Oil drain (Incl. 73) 72A 9556 Oil Drain Plug (Use as required) * Drain Plug Gasket (Do not use w/plast ic plug) Seal, Oil Shaft, Mechanical governor A Washer, Flat Gear Assy., Governor (Incl. 81) A Spool, Governor Ring, Retaining Screw, 1/4-20 x 1-1/4" Key, Flywheel Washer, Belleville Nut, Flywheel Screw, 1/4-20 x 5/8" Ground Wire A * Gasket, Cylinder head A Head, Cylinder (Incl. 131) A Intake Valve (STD)(Incl.151) (Inverte d Ports) A Intake Valve (1/32" OS)(Incl.151) (Inverted Ports) C Exhaust Valve (STD)(Incl. 151) (Inverted Ports) C Exhaust Valve (1/32" OS)(Incl. 151) (Inverted Ports) Washer (Not used in late production) Washer (Used on late production)

3 LAV B Page 3 of 9 Engine Parts List # A Screw, 5/16-18 x 1-1/2" (Use as requi red) Screw, 5/16-18 x 1-1/2" (Use as requi red) A Screw, 5/16-18 x 2" (Use as required) A Screw, 5/16-18 x 2-1/2" (Use as requi red) Spark Plug (J-8C) Valve Spring Cap) (Used in early prod uction) Spring, Valve Cap, Lower valve spring A * Gasket, Valve spring cover A Body Assy., Breather (Incl. 169 & 171 ) Element, Breather Screw, x 1/2" Nut & Lockwasher, 1/ Screw, 1/4-28 x 7/8" Screw, 1/4-28 x 7/8" A * Gasket, Carburetor Pipe, Intake Link, Governor spring Control Bracket (Incl. 203, 204 & 206 ) Spring, Compression Screw, 5-40 x 7/16" Terminal Assy Link, Governor-to-throttle Screw, x 9/16" Screw, 1/4-20 x 13/16" A * Gasket, Intake Screw, x 1/2" A * Gasket, Air cleaner B Housing, Blower NOTE: Replacement hardware may differ when servicing starter assy. or blower housing. Refer to Service Bulletin Screw, 1/4 20 x 5/8" Screw, Torx T-30, 1/4-20 x 1/2" (Use as req.) Screw, 1/4-28 x 7/16" (Use as require d) Screw & Lockwasher, 1/4-28 x 1/2" 287 Pop Rivet (Purchase locally) (3/16" d ia.) 287A Nut & Lockwasher, 1/4-28 (Use as requ ired) 290B Connector, Fuel line (Braided 8-1/4") (21cm) 290A Fuel Line (Metal 3-3/8") Fuel Line(Braided 8-1/4")(21 cm)(use as req.) Fuel Line (Epichlorohydrin 6-3/4") (1 7 cm) Fuel Line (Braided 16")(40 cm)(use as req.) Fuel Line Clamp (Use as required) A Fuel Tank (Incl. 292 & 301) B Fuel Cap (Std.) (Use as required) Fuel Cap (Use as required) Fuel Cap (use as required) Oil Fill Tube 325A Clip, Hi-tension wire (Use as require d) 370A Name & Instruction Decal Decal, Instruction Magneto (W/Ring Gear) NOTE: This magneto is not available as an assembly. The magneto number is shown for reference purposes only. Order component parts individually, as shown in parts breakdown. Refer to Division 5, Section B, page24 or Fiche 6, Grid F-11 for breakdown) A Contact Assy., Breaker

4 LAV B Page 4 of 9 Engine Parts List # B Condenser A Inlet Needle, Seat, Gasket & Spring A ssy D * Gasket Set (Incl. items marked *) SAE 30 4-Cycle Engine Oil (Quart) A Gauge, Visual fuel

5 LAV B Page 5 of 9 Engine Parts List #2

6 LAV B Page 6 of 9 Engine Parts List # Spring, Governor Washer, Tang Washer, Flat PTO Shaft (Incl. 54) 55B Pin, P.T.O. shaft Gear, Worm Ring, Retaining Seal, Oil Washer, Flat Screw, 1/4-20 x 2-1/4" Washer, Belleville Nut, Flywheel Screw, 1/4-28 x 7/8" Screw, 1/4 20 x 5/8" Screw, 1/4-20 x 5/8" Screw, 1/4-28 x 7/16" (Use as require d) Screw & Lockwasher, 1/4-28 x 1/2" 287 Pop Rivet (Purchase locally) (3/16" d ia.) Oil Fill Tube "O" Ring (This "O" ring is required with metal fill tube only when replacement mounting flange with.777 dia. oil fill hole has been used.) "O" Ring "O" Ring Screw, x 1/2" Dipstick (Incl. 307) 370A Name & Instruction Decal Decal, Instruction 379A Diaphragm Assy. (Incl. gasket) A Inlet Needle, Seat, Gasket & Spring A ssy. 380A Carburetor (Incl. 184) (Refer to Division 5, Section A, page 96 or Fiche 6, Grid D-11 for breakdown) Rope Assy., Starter Pulley, Starter Electric Side Mount Motor (12 Volt) (Refer to Division 5, Section D, page 12 or Fiche 6, Grid G-8 for breakdown) Cap, Pulley Bracket, Starter mounting Washer (Use as required) Screw, 1/4-20 x 5/8" Screw, 1/4-20 x 5/8" Washer, Flat Spacer Key & Chain Assy Charger, Battery (110 Volt) (Domestic ) Charger, Battery (220 Volt) (Export O nly) Bracket, Battery box Switch Box Clamp (3/4") Switch Box Clamp (7/8") Screw, Retainer "U" Clip Starter Cord Assy. (56") Terminal, Charging Wire, Terminal Screw, 8-14 x 3-1/2" Box, Battery

7 LAV B Page 7 of 9 Engine Parts List # Plug, Output Battery Cover Ass'y.(Incl. 1156, 1157 & 1160) A Battery Box Assy.(Incl.1154 & 1156 th ru 1161) Bracket Ass'y. (Use as required) Open End Rivet (Use as required)

8 LAV B Page 8 of 9 Engine Parts List #3

9 LAV B Page 9 of 9 Engine Parts List # Spring, Governor A * Gasket, Valve spring cover Element, Breather Screw, x 1/2" Screw, 1/4-28 x 7/8" Lever, Carburetor control 220A Knob, Control Screw, x 1/2" 240A Body, Air cleaner 245B Screen, Air cleaner Element, Air cleaner Cover, Air cleaner Screw, 1/4-20 x 5/8" 275A Muffler Screw, Torx T-30, 1/4-20 x 1/2" (Use as req.) Screw, 1/4-28 x 7/16" (Use as require d) Screw & Lockwasher, 1/4-28 x 1/2" 287 Pop Rivet (Purchase locally) (3/16" d ia.) Fuel Line(Braided 8-1/4")(21 cm)(use as req.) Fuel Line (Epichlorohydrin 6-3/4") (1 7 cm) Fuel Line (Braided 16")(40 cm)(use as req.) Fuel Line Clamp (Use as required) Oil Fill Tube A Primer Assy. (Incl. 185, 186 & 187) C Line, Primer Nut, Conduit 370B Decal, Air cleaner Muffler Adapter Kit (Incl. 274 & 277A ) (Inverted Ports) Screw, 8-32 x 1/2" Ring, Retaining Washer, Flat Spring, Compression