SolidWorks Tutorial 5 TIC-TAC-TOE
|
|
|
- Randolph Bradford
- 7 years ago
- Views:
Transcription
1 SolidWorks Tutorial 5 TIC-TAC-TOE
2 TIC-TAC-TOE In this tutorial we will create a Tic-Tac-Toe game. The game consists of two plates that are on top of each other. In the top plate, there are holes for inserting small cylinders marked X or O. In this exercise we repeat a lot of tools we already know and add a few others: working with configurations and the use of standard Parts. Some new features in this tutorial include working with tolerances and fittings and working with patterns. Work plan First, we will create the top plate. We will do this according to the drawing below. We will execute following steps: 1. First, we will create the top plate first with dimensions 60 x 60 x Then, we will make four counter bore holes. 3. Finally, we will create a pattern of 9 holes. 2
3 1 Start SolidWorks and open a new part Select the Top Plane. 2. Click on Sketch in the CommandManager. 3. Click on Rectangle. 3 Draw a rectangle: 1. Click on Center Rectangle in the PropertyManager. 2. Click on the origin. 3. Click at a random point to get the second corner. 3
4 4 Add a horizontal dimension to the sketch, as in the illustration on the right. Change this dimension to 60mm. Push the <Esc> key on the keyboard to end the command. 5 Set the length of the horizontal and vertical lines to the same length: 1. Select a vertical line. 2. Push the <Ctrl> button and click on a horizontal line. 3. Click on Equal in the PropertyManager. Tip! Remember that a blue field in the PropertyManager is a selection field. You can add elements by clicking on them in your model and you can also delete elements from it (e.g., when you have selected a wrong element). When you see a pink-colored selection field, you do not have to use the Ctrl> key to select more than one element. To remove an element from the list, click on the element in the pink field and push the <Del> (delete) key on your keyboard. SolidWorks often asks you if you really want to remove the element from the selection field to prevent inadvertent deletions. Tip! The sketch is now fully defined. You can determine this from the color of the lines in the sketch: 4
5 - Blue means: the sketch is not fully defined. - Black means: the sketch is fully defined. You can check if a sketch is fully defined in the status bar at the bottom of the screen. In SolidWorks it is not mandatory to make a fully defined sketch, but it is a good practice to do this because it can help you to avoid a lot of problems when creating a model later. In addition to the colors blue and black, a line in a sketch can turn red or yellow. - Red or Yellow means: the sketch is over-defined. Try the following: set the dimension of the height of the square. The Make Dimension Driven? message appears: You have entered too much information because: - The dimension you added says the height is 60mm. - The relation between the two lines you have created before says the height is equal to the width, which is also 60. The height is defined twice now, and this creates a conflict in SolidWorks. You must resolve this inconsistency. In the menu that is shown above, the best thing to do is choose Cancel. The dimension will not be set. Did you make an over-defined sketch anyway? Then, throw away (delete) dimensions and/or relations, so that the sketch is no longer over-defined. 5
6 6 Click on Features in the CommandManager, then on Extruded Boss/Base. 1. Set the thickness of the plate to 10 mm. 2. Click on OK. 7 Next, we will make a sketch in which we determine the exact position of the holes: 1. Select the top plane of the plate 2. Click on the View Orientation icon. 3. Click on Normal To. 8 Draw another rectangle with a dimension of 46 mm. Follow the steps 3 to 5 again if you need help. 6
7 9 Click on Exit Sketch in the CommandManager. We will not use this sketch to make a feature. 10 Start up a new sketch. 1. Select the top plane again. 2. Click on Circle in the CommandManager. 3,4 Draw a circle like the one in the illustration. 11 Set the dimension between the circle and one of the diagonal lines that you have drew previously: 1. Click on Smart Dimension in the CommandManager. 2. Click on the center of the circle. 3. Click on the diagonal line. 4. Set the dimension. 5. Change it to 15mm. 6. Click on OK. 7
8 12 Next, set the dimension to the other diagonal line (15mm) and the diameter of the circle (Ø8mm). Push the <Esc> key to close the Smart Dimension command. 13 To set an exact fitting to the hole (Ø8), execute the following steps: 1. Select a dimension (it turns green). 2. Be sure that Tolerance/Precision is visible in the PropertyManager. Click on the double arrows to reveal it. 3. Set Tolerance type to Fit. 4. Select a fitting of D10 in the Hole Fit field. 5. Click on OK. Tip! In this and the following tutorials, we will be using the commands from the CommandManager more often. At this point, you should be getting used in working with SolidWorks and might find it more convenient to use the quick menu. This quick menu can be activated by pushing the S on the keyboard. The most important and most frequently used commands will appear. You will see the commands and functions that are associated with the part of the menu in which you are working, so you will see different commands/functions when you are in a sketch mode than when you are in feature mode. 8
9 14 Make a hole in this sketch: click on Features in the CommandManager and then on Extruded Cut. Set the depth of the hole in the PropertyManager to Through all and click on OK We will complete the hole pattern now. 1. Select the hole you just created. 2. Click on the Linear pattern icon in the CommandManager. Next, set following features: 1. Select ONE of the diagonal lines. 2. Check to make sure that the line appears in the selection field. 3. Set the distance between the copies to 15mm. 4. Set the number of copies to Whenever the copies are placed on the wrong side, click on Reverse Direction. 9
10 17 Repeat these steps in the area named Direction 2. For this purpose, select the other diagonal line. If the preview looks good to you, click on OK. 18 We will now create the mounting holes for the bolts. Click on Hole Wizard in the CommandManager. 10
11 19 Set the following features in the PropertyManager: 1. Select the hole type Counter bore. 2. Set the ISO. Standard: 3. Set Type: Hex Socket Head ISO Set Size: M5. 5. Click on the Positions tab. 20 Next, click at the four corners of the sketch to position the holes. Click on OK. 11
12 21 The first part, the top plate, is now ready. Save this file as: Slab.SLDPRT. Tip: make a new folder on your computer first. You can arrange all of the files by product. Work plan We will now create the second part, the bottom plate. We will do this in accordance with the drawing below. Notice that this part looks very much like the first one. The perimeter dimensions and the position of the mounting holes are the same. That is why we will create a configuration from the first part to produce the second one. 22 Click on the ConfigurationManager tab. 12
13 23 The name of the configuration is Default. Doubleclick on this name to change it to Top Click your right mouse button on the upper line in the ConfigurationManager. 2. Select Add Configuration from the menu Set the name of the new configuration to: Bottom. 2. Click on OK. 26 There are two configurations in the list now: Top (gray, non-active), and Bottom (black, active). We will work with the active configuration. Click on the FeatureManager tab. 13
14 27 Now Suppress the last three features that you just made: 1. Click on the feature Extrude2. 2. Hold the Shift key on the keyboard and click on the last feature. 3. Release the Shift key. The last three features are now selected, and a small options menu appears. 4. Select: Suppress in the menu. All holes have disappeared from the model. 28 Next, we will make some tapped holes with M5 thread. Click on the Hole Wizard in the CommandManager. 14
15 29 Select the hole type Tap in the PropertyManager. Make sure all settings are equal to the settings in the illustration at right. Click on the Positions tab. 30 Click on the four corners of the sketch to position the holes. Click on OK. 15
16 31 Whenever no thread pattern appears in the holes, then change the following settings: 1. Click the right mouse button on Annotations in the FeatureManager. 2. Select Details Make sure that the option Shaded cosmetic threads is checked. 2. Click on OK. 33 Next, we want to hide the sketch we have used to make the holes: 1. Click with the right mouse button on the Sketch in the FeatureManager. 2. Select menu. Hide in the 16
17 34 Reactivate the configuration of the top plate. Click on the ConfigurationManager tab. 35 Double-click on the configuration Top in the ConfigurationManager. 36 Save the file. Work plan The third part is the cylinder. We will create this by using the dimensions of the drawing below. To be able to play Tic-Tac-Toe, we need to insert an X or an O at the top of each cylinder. We will do this by making two configurations of the cylinder. 37 Open a new part. 17
18 38 Open a sketch in the Top plane. Draw a circle, with the center on top of the origin. Set a dimension Ø8. 39 Set the fitting to h9. 1. Select the dimension. 2. Set the Tolerance type to fit in the PropertyManager. 3. Set Shaft fit to h Drag the height of the extrusion to 20mm. 2. Click on OK. 18
19 41 We will now make an angled edge at the top and at the bottom of the cylinder with the Chamfer command. Click on Chamfer in the CommandManager Click on the vertical outside plane of the cylinder. 2. Set the sloped distance to 1mm in the PropertyManager. 3. Check the angle to be Click on OK Select the top plane of the cylinder. 2. Click on Sketch Text in the CommandManager. 19
20 44 1. Type in the capital X in the text field. 2. Uncheck the option Use document font. 3. Click on the Font button. 45 Check in the menu to make sure the text height is set to 4mm, and click on OK. 46 Click on OK in the PropertyManager. 20
21 47 Rotate the model with the Normal to command so you can get a good view of the sketch. Drag the letter to the centre of the plane. 48 Click on Features in the CommandManager and next on Extruded Cut Set the 0.25mm. depth to 2. Click on OK. 50 The cylinder with the X is now ready. Save the file as: Shaft.SLDPRT. 21
22 51 To make the cylinder with the O we will use a second configuration. Click on the ConfigurationManager tab. 52 Change the name of the current configuration ( Default ) to Shaft-X. Create a new configuration called Shaft-O. If necessary, compare these commands to steps 24 to 26. Check to make sure that the configuration Shaft-O is active (black). Click on the FeatureManager tab. 53 With the Shaft-O configuration active, we must hide the letter X. 1. Click on the last features which you have made. 2. Select Suppress in the menu that appears. 22
23 54 Now, put a letter O on the top plane of the cylinder. Do this in exactly the same way as you did before with the letter X in steps 43 to Save the file. Open a new assembly. 56 When you did not close the two parts we just created (Slab and Shaft) you will see the image on the right. 1. Click on the file Slab. 2. Click on OK. If you did close this file, find it with the Browse command. 57 Click on Insert Components in the CommandManager. 23
24 58 Add the same part again. Place it just below the first one. 59 Next, we have to change the configuration of the bottom plate. 1. Click with the right mouse button somewhere on the bottom plate Select Configure Component in the menu that appears. 1. Select the Configuration Bottom. 2. Click on OK. Tip! When a part is open while added to an assembly, you can only select the desired configuration AFTER putting it in the assembly. That is what we have just done. When a part is closed, click on the PropertyManager and Browse to find it (see step 56). In the menu that appears, you can select the right configuration directly. Therefore, sometimes it is more convenient to use the Browsefunction anyway, even though the part is open. 24
25 61 Next, we have to align the two parts with the mate command. Click on Mate in CommandManager. 62 the Select the sides of both parts as shown in the illustration. Click on OK. 63 Select two other sides of both parts as shown in this illustration. Click on OK. 64 Select the top plane of the bottom part. 25
26 65 Next rotate the model so you get a good view of the bottom of the top part and select the bottom plane. Double-click on OK. 66 Next we will put the hexagon socket head screws in the model. 1. Open the Design Library in the Task Pane. 2. Click on Toolbox. 3. ISO. 4. Bolts and Screws. 5. Hexagon Socket Head Screws. 6. Select: Hex Socket Head ISO Drag the bolt to your model. Release the mouse button at the lower edge of one of the countersink holes. 26
27 68 Set the following features in the PropertyManager: 1. Size : M5. 2. Thread Length : Thread Display : Cosmetic. 4. Click on OK. 69 Put hexagon head screws in the other holes as well. 70 Finally, the cylinders (pegs) should be placed in the holes. Click on Insert Components in the CommandManager. 27
28 71 Place the cylinder or peg in the assembly 8 times at a random position. Note that it does not matter is you pick an X or O cylinders. We will change four of them later. Tip! 72 You can use the Insert Components command 8 times to insert the pegs, but it is much quicker to drag the part from the FeatureManager, holding the <Ctrl> key. A copy of the part is made every time you do so. Next, we will change the letter on four of the pegs. Right-click on a peg and select Configure component. 28
29 73 1. Select the desired configuration in the menu that appears: when a cylinder has an O on top, select the X configuration or do this the other way around. 2. Click on OK. 74 Repeat this step for three other pegs. 75 Next, we have to mate the pegs in the holes. Click on Mate in CommandManager. the 29
30 76 Select the two planes as shown in the illustration on the right. Click on OK. 77 Repeat the last step for all the pegs and select a different hole for every peg. The height of the pegs is not yet been determined. You can still move all of the pegs up and down by dragging them. 30
31 78 79 We will make the final mate now. 1. Click on the Multiple Mate Mode in the PropertyManager. 2. Rotate the model so you get a good view of the INSIDE of a hole. Through the hole you can see the top plane of the bottom part. Select this plane. Rotate the model again so you can see the bottom side of the pegs. 1. Select the bottom side of all pegs. 2. Click on OK. 31
32 80 The assembly is ready now. Save the file as: Tictactoe.SLDASM. What are the main fea- In this tutorial we have repeated al lot of what we have seen and done betures you have learned fore: in this tutorial? Creating simple parts and shapes. Working with configurations. Working with standard parts. Working with the Hole Wizard. We have also learned some new topics: You have set fittings at holes and/or pegs. You have seen how to use text in a sketch. You have learned some new tricks. 32
33 33
SolidWorks Tutorial 3 MAGNETIC BLOCK
SolidWorks Tutorial 3 MAGNETIC BLOCK Magnetic Block In this exercise you will make a magnetic block. To do so, you will create a few parts, which you will assemble. You will learn the following new applications
SolidWorks Tutorial 5
SolidWorks Tutorial 5 Tic-Tac-Toe Preparatory Vocational Training and Advanced Vocational Training Dassault Systèmes SolidWorks Corporation, 75 Wyman Street Waltham, Massachusetts 05 USA Phone: +-800-69-9000
SolidWorks Tutorial 4 CANDLESTICK
SolidWorks Tutorial 4 CANDLESTICK Candlestick In this tutorial you will make a simple container and a candlestick out of sheetmetal. You will learn about working with sheet metal in SolidWorks. We will
Chapter 9. Editing Features. Learning Objectives
Chapter 9 Editing Features Learning Objectives After completing this chapter, you will be able to: Edit features. Edit sketches of the sketch based features. Edit the sketch plane of the sketch based features.
Introduction to Autodesk Inventor for F1 in Schools
Introduction to Autodesk Inventor for F1 in Schools F1 in Schools Race Car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s digital prototyping strategy
Introduction to Autodesk Inventor for F1 in Schools
F1 in Schools race car Introduction to Autodesk Inventor for F1 in Schools In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital Prototyping strategy
SolidWorks Implementation Guides. Sketching Concepts
SolidWorks Implementation Guides Sketching Concepts Sketching in SolidWorks is the basis for creating features. Features are the basis for creating parts, which can be put together into assemblies. Sketch
Generative Drafting. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes
Generative Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Generative Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting
Solidworks Lesson 6 - Assembly & Part Drawings. UCF Engineering
Solidworks Lesson 6 - Assembly & Part Drawings UCF Engineering Mechanical Drawings So far we have been dealing with creating parts and assemblies in SolidWorks, however, when you go to get a part machined,
Chapter 1. Creating Sketches in. the Sketch Mode-I. Evaluation chapter. Logon to www.cadcim.com for more details. Learning Objectives
Chapter 1 Creating Sketches in Learning Objectives the Sketch Mode-I After completing this chapter you will be able to: Use various tools to create a geometry. Dimension a sketch. Apply constraints to
Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional.
Working with layout Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional. In this tutorial, you will create a poster for an imaginary coffee
Microsoft Word 2010. Quick Reference Guide. Union Institute & University
Microsoft Word 2010 Quick Reference Guide Union Institute & University Contents Using Word Help (F1)... 4 Window Contents:... 4 File tab... 4 Quick Access Toolbar... 5 Backstage View... 5 The Ribbon...
Using Microsoft Word. Working With Objects
Using Microsoft Word Many Word documents will require elements that were created in programs other than Word, such as the picture to the right. Nontext elements in a document are referred to as Objects
Windows XP Pro: Basics 1
NORTHWEST MISSOURI STATE UNIVERSITY ONLINE USER S GUIDE 2004 Windows XP Pro: Basics 1 Getting on the Northwest Network Getting on the Northwest network is easy with a university-provided PC, which has
Visit the following websites to learn more about this book:
INSIDE: MultiMedia CD SolidWorks 2011 Tutorial with MultiMedia CD An audio/visual presentation of the tutorial projects A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling Using over 50 feature
SpaceClaim Introduction Training Session. A SpaceClaim Support Document
SpaceClaim Introduction Training Session A SpaceClaim Support Document In this class we will walk through the basic tools used to create and modify models in SpaceClaim. Introduction We will focus on:
Creating a Poster in PowerPoint 2010. A. Set Up Your Poster
View the Best Practices in Poster Design located at http://www.emich.edu/training/poster before you begin creating a poster. Then in PowerPoint: (A) set up the poster size and orientation, (B) add and
SolidWorks: Mirror, Revolve, and. Introduction to Robotics
SolidWorks: Mirror, Revolve, and Circular Pattern Introduction to Robotics Let s Review At this point we have learned the following: Extrude Boss/Base Extruded Cut Adding Relations and Dimensions Linear
Understand the Sketcher workbench of CATIA V5.
Chapter 1 Drawing Sketches in Learning Objectives the Sketcher Workbench-I After completing this chapter you will be able to: Understand the Sketcher workbench of CATIA V5. Start a new file in the Part
Sample Table. Columns. Column 1 Column 2 Column 3 Row 1 Cell 1 Cell 2 Cell 3 Row 2 Cell 4 Cell 5 Cell 6 Row 3 Cell 7 Cell 8 Cell 9.
Working with Tables in Microsoft Word The purpose of this document is to lead you through the steps of creating, editing and deleting tables and parts of tables. This document follows a tutorial format
ACS Version 10.6 - Check Layout Design
ACS Version 10.6 - Check Layout Design Table Of Contents 1. Check Designer... 1 About the Check Design Feature... 1 Selecting a Check Template... 2 Adding a Check Template... 2 Modify a Check Template...
Introduction to CATIA V5
Introduction to CATIA V5 Release 16 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com
Creating Drawings in Pro/ENGINEER
6 Creating Drawings in Pro/ENGINEER This chapter shows you how to bring the cell phone models and the assembly you ve created into the Pro/ENGINEER Drawing mode to create a drawing. A mechanical drawing
WHAT S NEW IN WORD 2010 & HOW TO CUSTOMIZE IT
WHAT S NEW IN WORD 2010 & HOW TO CUSTOMIZE IT The Ribbon... 2 Default Tabs... 2 Contextual Tabs... 2 Minimizing and Restoring the Ribbon... 3 Customizing the Ribbon... 3 A New Graphic Interface... 5 Live
PowerPoint 2007: Basics Learning Guide
PowerPoint 2007: Basics Learning Guide What s a PowerPoint Slide? PowerPoint presentations are composed of slides, just like conventional presentations. Like a 35mm film-based slide, each PowerPoint slide
Part Design. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes
Part Design Page 1 Tutorial Objectives Description This tutorial is an introduction to Part Design. Message This tutorial illustrates how CATIA can Design precise 3D mechanical parts with an intuitive
TABLE OF CONTENTS. INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE...
Starting Guide TABLE OF CONTENTS INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE... 7 ADVANCE CONCRETE USER INTERFACE... 7 Other important
Using Parametric Equations in SolidWorks, Example 1
Using Parametric Equations in SolidWorks, Example 1 (Draft 4, 10/25/2006, SW 2006) Introduction In this example the goal is to place a solid roller on a solid wedge. Their relationship will be governed
Digital Marketing EasyEditor Guide Dynamic
Surveys ipad Segmentation Reporting Email Sign up Email marketing that works for you Landing Pages Results Digital Marketing EasyEditor Guide Dynamic Questionnaires QR Codes SMS 43 North View, Westbury
In this session, we will explain some of the basics of word processing. 1. Start Microsoft Word 11. Edit the Document cut & move
WORD PROCESSING In this session, we will explain some of the basics of word processing. The following are the outlines: 1. Start Microsoft Word 11. Edit the Document cut & move 2. Describe the Word Screen
Create a Poster Using Publisher
Contents 1. Introduction 1. Starting Publisher 2. Create a Poster Template 5. Aligning your images and text 7. Apply a background 12. Add text to your poster 14. Add pictures to your poster 17. Add graphs
2013 Getting Started Guide
2013 Getting Started Guide The contents of this guide and accompanying exercises were originally created by Nemetschek Vectorworks, Inc. Vectorworks Fundamentals Getting Started Guide Created using: Vectorworks
Unit 21 - Creating a Button in Macromedia Flash
Unit 21 - Creating a Button in Macromedia Flash Items needed to complete the Navigation Bar: Unit 21 - House Style Unit 21 - Graphics Sketch Diagrams Document ------------------------------------------------------------------------------------------------
SketchUp Instructions
SketchUp Instructions Every architect needs to know how to use SketchUp! SketchUp is free from Google just Google it and download to your computer. You can do just about anything with it, but it is especially
Autodesk Fusion 360 Badge Guide: Design an F1 in Schools Trophy
Autodesk Fusion 360 Badge Guide: Design an F1 in Schools Trophy Abstract: Gain basic understanding of creating 3D models in Fusion 360 by designing an F1 in Schools trophy. This badge may be claimed by
Pro/ENGINEER Wildfire 4.0 Basic Design
Introduction Datum features are non-solid features used during the construction of other features. The most common datum features include planes, axes, coordinate systems, and curves. Datum features do
Fireworks CS4 Tutorial Part 1: Intro
Fireworks CS4 Tutorial Part 1: Intro This Adobe Fireworks CS4 Tutorial will help you familiarize yourself with this image editing software and help you create a layout for a website. Fireworks CS4 is the
SolidWorks 2013 Tutorial with
SolidWorks 2013 Tutorial with Video Instruction A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard CSWP Marie P. Planchard CSWP Video Instruction SDC PUBLICATIONS Schroff
PowerPoint 2013: Basic Skills
PowerPoint 2013: Basic Skills Information Technology September 1, 2014 1 P a g e Getting Started There are a variety of ways to start using PowerPoint software. You can click on a shortcut on your desktop
Microsoft Access 2010 handout
Microsoft Access 2010 handout Access 2010 is a relational database program you can use to create and manage large quantities of data. You can use Access to manage anything from a home inventory to a giant
Creating a Logo in CorelDRAW
Creating a Logo in CorelDRAW In this tutorial, we will look at creating a logo for an electrical contracting firm. Our goal is to create a logo that is clean and easily recognizable. Lighthouse Electric
Handout: Word 2010 Tips and Shortcuts
Word 2010: Tips and Shortcuts Table of Contents EXPORT A CUSTOMIZED QUICK ACCESS TOOLBAR... 2 IMPORT A CUSTOMIZED QUICK ACCESS TOOLBAR... 2 USE THE FORMAT PAINTER... 3 REPEAT THE LAST ACTION... 3 SHOW
SolidWorks. SolidWorks Teacher Guide. and Student Courseware
SolidWorks SolidWorks Teacher Guide and Student Courseware SolidWorks Corporation Outside the U.S.: +1-978-371-5011 300 Baker Avenue Fax: +1-978-371-7303 Concord, Massachusetts 01742 USA Email: info@solidworks.com
Introduction to Measurement Tools
Introduction to Measurement Tools Revu's built-in measurement tools make it easy to take length, area, perimeter, diameter, volume and radius measurements, count from PDFs and perform area cutouts. Compatibility
Communicate: In Print
Communicate: In Print A simple guide Work areas Communicate: In Print has two different modes in which to edit your documents: Create and Adjust modes. These are easily interchangeable and the toolbars
CAD Student Guide. Engineering Design and Technology Series
Engineering Design and Technology Series CAD Student Guide Dassault Systèmes SolidWorks Corporation, 175 Wyman Street, Waltham, Massachusetts 02451 USA Phone: +1-800-693-9000 Outside the U.S.: +1-781-810-5011
Speaker Drafting. Page 1 1997 2001 DASSAULT SYSTEMES
Speaker Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Assembly Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting
CATIA Basic Concepts TABLE OF CONTENTS
TABLE OF CONTENTS Introduction...1 Manual Format...2 Log on/off procedures for Windows...3 To log on...3 To logoff...7 Assembly Design Screen...8 Part Design Screen...9 Pull-down Menus...10 Start...10
Microsoft Office 2010: Introductory Q&As PowerPoint Chapter 1
Microsoft Office 2010: Introductory Q&As PowerPoint Chapter 1 Are the themes displayed in a specific order? (PPT 6) Yes. They are arranged in alphabetical order running from left to right. If you point
SMART Notebook: Basics and Application
SMART Notebook: Basics and Application Table of Contents TESS Connection... 3 Version Number... 3 Tour of the Window... 5 The Main Toolbar... 5 The Sidebar... 18 Page Sorter... 19 The Gallery... 23 Searching...
Microsoft PowerPoint 2010 Computer Jeopardy Tutorial
Microsoft PowerPoint 2010 Computer Jeopardy Tutorial 1. Open up Microsoft PowerPoint 2010. 2. Before you begin, save your file to your H drive. Click File > Save As. Under the header that says Organize
Sage Accountants Business Cloud EasyEditor Quick Start Guide
Sage Accountants Business Cloud EasyEditor Quick Start Guide VERSION 1.0 September 2013 Contents Introduction 3 Overview of the interface 4 Working with elements 6 Adding and moving elements 7 Resizing
[Not for Circulation]
![[Not for Circulation]](/thumbs/39/20045725.jpg "[Not for Circulation]")
Using SMART Notebook SMART Notebook is software meant to supplement use with the SMART Board. The software helps users create interactive presentations, and offers a variety of ways to enhance presenting
Planning and Managing Projects with Microsoft Project Professional 2013
Slides Steps to Enter Duration: 1. In the Duration column of a task, enter a value, and press Enter on your keyboard Important Points: The default time unit is days, so when you enter 5, this becomes 5
Triggers & Actions 10
Triggers & Actions 10 CHAPTER Introduction Triggers and actions are the building blocks that you can use to create interactivity and custom features. Once you understand how these building blocks work,
SMART board 101. SMART board 101 Training
SMART board 101 SMART board 101 Training For those who want to learn/remember how to connect it, turn it on, configure it, and feel better about using it at a basic level. We will talk about how the SMART
6. If you want to enter specific formats, click the Format Tab to auto format the information that is entered into the field.
Adobe Acrobat Professional X Part 3 - Creating Fillable Forms Preparing the Form Create the form in Word, including underlines, images and any other text you would like showing on the form. Convert the
Excel basics. Before you begin. What you'll learn. Requirements. Estimated time to complete:
Excel basics Excel is a powerful spreadsheet and data analysis application, but to use it most effectively, you first have to understand the basics. This tutorial introduces some of the tasks and features
Introduction to the TI-Nspire CX
Introduction to the TI-Nspire CX Activity Overview: In this activity, you will become familiar with the layout of the TI-Nspire CX. Step 1: Locate the Touchpad. The Touchpad is used to navigate the cursor
CATIA Drafting TABLE OF CONTENTS
TABLE OF CONTENTS Introduction...1 Drafting...2 Drawing Screen...3 Pull-down Menus...4 File...4 Edit...5 View...6 Insert...7 Tools...8 Drafting Workbench...9 Views and Sheets...9 Dimensions and Annotations...10
SMART BOARD USER GUIDE FOR PC TABLE OF CONTENTS I. BEFORE YOU USE THE SMART BOARD. What is it?
SMART BOARD USER GUIDE FOR PC What is it? SMART Board is an interactive whiteboard available in an increasing number of classrooms at the University of Tennessee. While your laptop image is projected on
DOING MORE WITH WORD: MICROSOFT OFFICE 2010
University of North Carolina at Chapel Hill Libraries Carrboro Cybrary Chapel Hill Public Library Durham County Public Library DOING MORE WITH WORD: MICROSOFT OFFICE 2010 GETTING STARTED PAGE 02 Prerequisites
How to make a line graph using Excel 2007
How to make a line graph using Excel 2007 Format your data sheet Make sure you have a title and each column of data has a title. If you are entering data by hand, use time or the independent variable in
Smart Board Notebook Software A guide for new Smart Board users
Smart Board Notebook Software A guide for new Smart Board users This guide will address the following tasks in Notebook: 1. Adding shapes, text, and pictures. 2. Searching the Gallery. 3. Arranging objects
Microsoft Excel 2010 Charts and Graphs
Microsoft Excel 2010 Charts and Graphs Email: training@health.ufl.edu Web Page: http://training.health.ufl.edu Microsoft Excel 2010: Charts and Graphs 2.0 hours Topics include data groupings; creating
Epson Brightlink Interactive Board and Pen Training. Step One: Install the Brightlink Easy Interactive Driver
California State University, Fullerton Campus Information Technology Division Documentation and Training Services Handout Epson Brightlink Interactive Board and Pen Training Downloading Brightlink Drivers
Microsoft Excel 2010 Tutorial
1 Microsoft Excel 2010 Tutorial Excel is a spreadsheet program in the Microsoft Office system. You can use Excel to create and format workbooks (a collection of spreadsheets) in order to analyze data and
Part Design. Preface What's New? Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index
Part Design Preface What's New? Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index Dassault Systèmes 1994-99. All rights reserved. Preface The CATIA Version 5 Part
UML Class Diagrams (1.8.7) 9/2/2009
8 UML Class Diagrams Java programs usually involve multiple classes, and there can be many dependencies among these classes. To fully understand a multiple class program, it is necessary to understand
WORKBOOK MODELING OF MULTI- MEMBER MACHINES
WORKBOOK MODELING OF MULTI- MEMBER MACHINES LUBLIN 2014 0 Author: Mirosław Ferdynus Desktop publishing: Mirosław Ferdynus Technical editor: Mirosław Ferdynus Figures: Mirosław Ferdynus Cover and graphic
Instructions for Formatting APA Style Papers in Microsoft Word 2010
Instructions for Formatting APA Style Papers in Microsoft Word 2010 To begin a Microsoft Word 2010 project, click on the Start bar in the lower left corner of the screen. Select All Programs and then find
Scientific Graphing in Excel 2010
Scientific Graphing in Excel 2010 When you start Excel, you will see the screen below. Various parts of the display are labelled in red, with arrows, to define the terms used in the remainder of this overview.
How to create pop-up menus
How to create pop-up menus Pop-up menus are menus that are displayed in a browser when a site visitor moves the pointer over or clicks a trigger image. Items in a pop-up menu can have URL links attached
Intellect Platform - The Workflow Engine Basic HelpDesk Troubleticket System - A102
Intellect Platform - The Workflow Engine Basic HelpDesk Troubleticket System - A102 Interneer, Inc. Updated on 2/22/2012 Created by Erika Keresztyen Fahey 2 Workflow - A102 - Basic HelpDesk Ticketing System
PowerPoint 2007 Basics Website: http://etc.usf.edu/te/
Website: http://etc.usf.edu/te/ PowerPoint is the presentation program included in the Microsoft Office suite. With PowerPoint, you can create engaging presentations that can be presented in person, online,
ABAQUS/CAE Tutorial: Analysis of an Aluminum Bracket
H. Kim FEA Tutorial 1 ABAQUS/CAE Tutorial: Analysis of an Aluminum Bracket Hyonny Kim last updated: August 2004 In this tutorial, you ll learn how to: 1. Sketch 2D geometry & define part. 2. Define material
SMART NOTEBOOK 10. Instructional Technology Enhancing ACHievement
SMART NOTEBOOK 10 Instructional Technology Enhancing ACHievement TABLE OF CONTENTS SMART Notebook 10 Themes... 3 Page Groups... 4 Magic Pen... 5 Shape Pen... 6 Tables... 7 Object Animation... 8 Aligning
Publisher 2010 Cheat Sheet
April 20, 2012 Publisher 2010 Cheat Sheet Toolbar customize click on arrow and then check the ones you want a shortcut for File Tab (has new, open save, print, and shows recent documents, and has choices
AutoDWG DWGSee DWG Viewer. DWGSee User Guide
DWGSee User Guide DWGSee is comprehensive software for viewing, printing, marking and sharing DWG files. It is fast, powerful and easy-to-use for every expert and beginners. Starting DWGSee After you install
Reviewing documents with track changes in Word 2013
Reviewing documents with track changes in Word 2013 Information Services Reviewing documents with track changes in Word 2013 This note covers how to use Word s reviewing tools to track the changes made
Creating Fill-able Forms using Acrobat 8.0: Part 1
Creating Fill-able Forms using Acrobat 8.0: Part 1 The first step in creating a fill-able form in Adobe Acrobat is to generate the form with all its formatting in a program such as Microsoft Word. Then
Chapter 23: Drafting in Worksheet View
Chapter 23: Drafting in Worksheet View Worksheet View is a powerful, 2D production drafting module. Here you can find all of the drawing and editing tools needed to create fast, accurate, detailed working
Getting Started in Tinkercad
Getting Started in Tinkercad By Bonnie Roskes, 3DVinci Tinkercad is a fun, easy to use, web-based 3D design application. You don t need any design experience - Tinkercad can be used by anyone. In fact,
Sketcher. Preface What's New? Getting Started Basic Tasks Customizing Workbench Description Glossary Index
Sketcher Preface What's New? Getting Started Basic Tasks Customizing Workbench Description Glossary Index Dassault Systèmes 1994-99. All rights reserved. Preface CATIA Version 5 Sketcher application makes
PowerPoint 2013: Absolute Beginners. Workbook
PowerPoint 2013: Absolute Beginners Workbook Edition 1 August 2014 Document Reference: 3809-2014 PowerPoint 2013: Absolute Beginners Contents Introduction Getting started with PowerPoint... 1 After the
Snagit 10. Getting Started Guide. March 2010. 2010 TechSmith Corporation. All rights reserved.
Snagit 10 Getting Started Guide March 2010 2010 TechSmith Corporation. All rights reserved. Introduction If you have just a few minutes or want to know just the basics, this is the place to start. This
Word 2007 WOWS of Word Office 2007 brings a whole new basket of bells and whistles for our enjoyment. The whistles turn to wows.
WOWS of Word Office brings a whole new basket of bells and whistles for our enjoyment. The whistles turn to wows. gfruth@wm.edu Templates Click on the Office Button PDF and select New. You can now change
Presentations and PowerPoint
V-1.1 PART V Presentations and PowerPoint V-1.2 Computer Fundamentals V-1.3 LESSON 1 Creating a Presentation After completing this lesson, you will be able to: Start Microsoft PowerPoint. Explore the PowerPoint
SolidWorks Building Blocks Tutorial. Toy-car
SolidWorks Building Blocks Tutorial Toy-car From the age of until the age of For use with SolidWorks Educational Release 2010-2011 This tutorial was developed for SolidWorks Worldwide and may be used by
Introduction to Word 2007
Introduction to Word 2007 You will notice some obvious changes immediately after starting Word 2007. For starters, the top bar has a completely new look, consisting of new features, buttons and naming
Word 2010: The Basics Table of Contents THE WORD 2010 WINDOW... 2 SET UP A DOCUMENT... 3 INTRODUCING BACKSTAGE... 3 CREATE A NEW DOCUMENT...
Word 2010: The Basics Table of Contents THE WORD 2010 WINDOW... 2 SET UP A DOCUMENT... 3 INTRODUCING BACKSTAGE... 3 CREATE A NEW DOCUMENT... 4 Open a blank document... 4 Start a document from a template...
Tutorials. If you have any questions, comments, or suggestions about these lessons, don't hesitate to contact us at support@kidasa.com.
Tutorials The lesson schedules for these tutorials were installed when you installed Milestones Professional 2010. They can be accessed under File Open a File Lesson Chart. If you have any questions, comments,
Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional.
Workspace tour Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional. In this tutorial, you will become familiar with the terminology and workspace
3D Viewer. user's manual 10017352_2
EN 3D Viewer user's manual 10017352_2 TABLE OF CONTENTS 1 SYSTEM REQUIREMENTS...1 2 STARTING PLANMECA 3D VIEWER...2 3 PLANMECA 3D VIEWER INTRODUCTION...3 3.1 Menu Toolbar... 4 4 EXPLORER...6 4.1 3D Volume
Microsoft Office PowerPoint 2013
Microsoft Office PowerPoint 2013 Navigating the PowerPoint 2013 Environment The Ribbon: The ribbon is where you will access a majority of the commands you will use to create and develop your presentation.
Making 3D Threads in Feature Based Solid Modelers
Making 3D Threads in Feature Based Solid Modelers THREAD BASICS Making true geometric threads in feature-based solid modelers is a fairly straightforward process and can be handled using several different
Microsoft Word defaults to left justified (aligned) paragraphs. This means that new lines automatically line up with the left margin.
Microsoft Word Part 2 Office 2007 Microsoft Word 2007 Part 2 Alignment Microsoft Word defaults to left justified (aligned) paragraphs. This means that new lines automatically line up with the left margin.
Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional.
Creating a logo Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional. In this tutorial, you will create a logo for an imaginary coffee shop.